OPA241UA - 25µA Micro-Power Op Amp | Texas Instruments
MPN: OPA241UA ✓ Hoạt độngOPA241UA Tóm tắt
An operational amplifier is a voltage-feedback analog building block that amplifies the difference between two input voltages while presenting high input impedance and low output impedance. The OPA241 belongs to the low-dropout, micropower operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its low operating current makes it suitable for sensor interfaces, portable instrumentation, battery monitoring, and low-duty-cycle control systems where continuous amplifier power would dominate the system budget.
The principal operating characteristics are a 25 µA supply current, 35 kHz gain-bandwidth product, 0.01 V/µs slew rate, and operation from a single 5 V supply. The device also provides rail-to-rail output swing, which increases usable output range on low-voltage rails. Low offset voltage supports accurate amplification of small sensor signals, while the high common-mode rejection ratio reduces sensitivity to supply and ground-disturbance signals. A unity-gain bandwidth of 35 kHz makes the amplifier appropriate for low-frequency signal conditioning rather than high-speed waveform processing.
OPA241UA is a single-amplifier implementation in the broader OPAx241 family, alongside the OPA2241 and OPA4241 dual and quad versions. The family targets portable applications where low power consumption, common-mode range, and output swing are more important than wideband performance. Single-supply operation also simplifies battery-powered design, while the small SOIC package supports conventional surface-mount assembly.
Typical uses include low-power sensor amplification, portable measurement equipment, battery-current monitoring, industrial signal conditioning, and low-leakage sensing interfaces. In these applications, the amplifier can sit close to a sensor and condition its output before conversion or transmission. The 35 kHz bandwidth is adequate for slow physiological, temperature, pressure, and position signals, but it is not intended for high-speed communications, pulse shaping, or precision audio workloads.
For a new design, verify the signal bandwidth, output load, common-mode range, and stability requirements against the manufacturer datasheet. Place the bypass capacitor close to the supply pins and avoid capacitive loading that can reduce phase margin. The low-current advantage should also be checked against the complete analog signal chain, since additional amplifiers, converters, and protection devices can consume more power than the OPA241UA itself.
This product page consolidates the manufacturer specifications, commercial sourcing guidance, package details, cross-reference alternatives, and application-focused engineering notes. It supports faster part selection by connecting the OPA241UA electrical limits with practical low-power circuit requirements rather than repeating only the basic ordering information.
Bộ thay thế dễ dàng lắp đặt cho OPA241UA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với OPA241UA (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Number of Channels, Operating Temperature Range, Package, Slew Rate.
OPA241UAG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD8676ARZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LT6015
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX44246
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
OPA241UA Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single operational amplifier |
| Supply Type | Single supply |
| Nominal Supply Voltage | 5 V |
| Điện áp yên tĩnh | 25 µA |
| Gain-Bandwidth Product | 35 kHz |
| Slew Rate | 0.01 V/µs |
| Supply Voltage Range | ±1.35 V to ±18 V |
| Output Swing | Rail-to-rail |
| Offset Voltage | Low |
| Common-Mode Rejection | High |
| Open-Loop Gain | High |
| Number of Channels | 1 channel |
| Số lượng chân | 8 pins |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Application | Battery-powered portable applications |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
Hướng dẫn cấu hình chân OPA241UA 8-pin soic
Cấu hình chân cho OPA241UA (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho OPA241UA.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
OPA241UA phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Interfaces, Portable Medical Instrumentation, Industrial Process Measurement, Battery Current Monitoring, Low-Power Data Acquisition, Precision Voltage Buffering.
Battery-Powered Sensor Interfaces
The OPA241UA is suitable for conditioning outputs from temperature, pressure, position, and electrochemical sensors in battery-operated equipment. Its 25 µA quiescent current limits the amplifier's contribution to standby power, while the 35 kHz gain-bandwidth product accommodates slow sensor signals without requiring a wideband amplifier. Place the device close to the sensor and use local supply bypassing to minimize sensitive traces and susceptibility to external interference. The rail-to-rail output can improve signal range on low-voltage rails, although the complete input and output ranges must remain within the datasheet limits for the selected gain and load.
Được đề xuất
Portable Medical Instrumentation
The OPA241UA can amplify low-level physiological or diagnostic signals in portable instruments where every microamp of supply current affects battery life. Its 25 µA quiescent current, low offset voltage, high common-mode rejection, and high open-loop gain support accurate amplification around a low-voltage analog front end. The 35 kHz bandwidth is appropriate for many ECG, pressure, and biochemical monitoring waveforms that remain below the amplifier's useful frequency range. Verify electrode protection, input bias-current error, patient-safety isolation, and applicable medical requirements independently of the amplifier's electrical performance.
Được đề xuất
Industrial Process Measurement
OPA241UA suits low-frequency industrial sensor chains where a 24 V source must be reduced to a compact, low-energy analog signal. Although the device is identified for 5 V single-supply operation, its documented supply range permits other suitable operating rails. The 25 µA supply current reduces power in remote monitoring loops, and the 0.01 V/µs slew rate supports slow process variables with reasonable small-signal bandwidth. Add protection against industrial transients and verify the exact input common-mode range, output swing, and grounding strategy before connecting field-wired sensors.
Được đề xuất
Battery Current Monitoring
The OPA241UA can amplify the voltage across a low-value shunt when monitoring current consumption in a portable battery system. Its low 25 µA supply current prevents the measurement amplifier from materially changing the load being measured, while low offset voltage supports accurate recovery of small voltage differences. The 35 kHz bandwidth is suitable for relatively slow charge and discharge current profiles rather than fast pulse currents. Use a Kelvin connection, high-side or low-side topology appropriate to the system ground, and an input filter sized against the shunt impedance and amplifier noise requirements.
Được đề xuất
Low-Power Data Acquisition
OPA241UA is useful in compact, low-duty-cycle data-acquisition systems that amplify sensor outputs before conversion and control overall energy use. The 25 µA quiescent current is beneficial when the acquisition node must operate throughout a long battery life, and the single 5 V supply simplifies system partitioning. The 35 kHz gain-bandwidth product is sufficient for many environmental, occupancy, and condition-monitoring inputs but not for high-speed vibration analysis. Select the gain and output range for the converter, account for settling time, and preserve a clean analog return path between the sensor, amplifier, and converter.
Được đề xuất
Precision Voltage Buffering
OPA241UA can provide voltage buffering and gain for low-level reference or control signals in compact portable equipment. Its high open-loop gain reduces output error when driving a moderate load, while low offset voltage helps preserve small reference levels. The rail-to-rail output increases the available range near the supply rails, and the 0.01 V/µs slew rate is sufficient for slowly changing control or measurement nodes. Confirm stability with the intended load capacitance, avoid excessive resistive loading, and use the datasheet's input common-mode and output-swing limits when operating near either rail.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho OPA241UA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | OPA241UAG4 | AD8676 | LT6015 | MAX44246 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Maxim Integrated |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
Bảo phân biệt quan trọng
- Very low supply demand for a general-purpose operational amplifier (vsOPA241UAG4)
- Single 5 V supply operation with rail-to-rail output (vsAD8676)
- Focused low-frequency signal-conditioning bandwidth (vsMAX44246)
Ghi chú thiết kế
Budget the OPA241UA's 25 µA quiescent current together with output-current demand and the power consumed by surrounding circuitry. A nominally low-current amplifier can still raise total system consumption after accounting for sensor biasing, bypass leakage, conversion electronics, and protection components. Where the system operates intermittently, evaluate whether the shutdown behavior of the upstream circuit can provide a larger saving than selecting a marginally lower-current amplifier.
Place the supply bypass capacitor immediately beside the OPA241UA power pins and route the return directly to the device ground. Keep sensitive input traces short, away from switching-node and high-current return paths. Because the gain-bandwidth product is 35 kHz, the circuit is intended for slow signals, but correct grounding and local decoupling still determine whether offset, interference, and supply ripple appear as gain or common-mode errors.
Do not assume that rail-to-rail output swing permits operation at or beyond either supply rail. Check the input common-mode range, output swing under the intended load, gain setting, and minimum supply voltage from the manufacturer datasheet. Likewise, verify capacitive-load stability before connecting long cables, large filter capacitors, or ADC sampling inputs directly to the output.
Thông tin tuân thủ
The Texas Instruments product and ordering pages identify OPA241UA as active in an 8-pin SOIC package with a -40 °C to +85 °C operating range. Specific environmental and material compliance declarations were not present in the cited excerpts and require confirmation from the manufacturer.