Texas Instruments

OPA694ID - 1.5GHz Wideband Op Amp | Texas Instruments

MPN: OPA694ID ✓ सक्रिय
<1.5 V Vdss ±80 mA Id 8-SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

OPA694ID अवलोकन

The Texas Instruments OPA694ID is a single-amplifier, wideband, low-power current-feedback operational amplifier with a 1.5 GHz gain-bandwidth product, 1700 V/µs slew rate, and low differential gain and phase errors. It is packaged in an 8-pin SOIC and provides approximately ±80 mA of output drive with less than 1.5 V of output voltage headroom, making it suitable for high-speed video, imaging, communications, and test-equipment signal chains.

A current-feedback operational amplifier is a voltage-feedback amplifier subclass whose feedback impedance determines closed-loop bandwidth and gain. Unlike a conventional voltage-feedback amplifier, a current-feedback amplifier maintains relatively stable bandwidth as closed-loop gain changes. This behavior is valuable in wideband systems where gain is adjusted across multiple stages, particularly when low differential gain and phase errors are important for maintaining signal integrity.

The OPA694ID combines more than 500 MHz bandwidth with low supply current, high slew rate, and strong output-drive capability. Its ±80 mA output stage can drive lower-impedance loads and downstream circuitry while retaining less than 1.5 V of headroom. The 1700 V/µs slew rate supports rapid transitions required by video routers, waveform generators, active filters, and high-speed instrumentation. The single-amplifier configuration also keeps board area and external component requirements compact.

Because the OPA694ID uses current feedback, feedback-network selection requires more care than with voltage-feedback amplifiers. A conventional 1 kΩ feedback resistor is often appropriate for modest gain, but the exact value should follow the manufacturer’s gain-versus-feedback-resistance guidance for the required closed-loop gain. Board parasitics, package inductance, and long feedback traces can materially affect isolation and stability at these bandwidths.

Typical applications include high-density video routing, broadcast and surveillance video systems, analog test equipment, communications receivers, and wideband active filters. In a video buffer, it can preserve large-signal swing while offering more than 500 MHz bandwidth. In instrumentation, its 1.5 GHz gain-bandwidth product supports amplification stages that must retain low distortion and timing accuracy.

Use short, impedance-controlled PCB traces, maintain symmetric routing around the amplifier, and place compensation or feedback components close to the relevant pins. Decoupling capacitors should connect directly between each supply pin and ground with a low-impedance return path. Avoid long loops around high-speed feedback nodes and test the completed layout with time-domain reflectometry or equivalent signal-integrity equipment.

This page combines the OPA694ID’s core electrical characteristics with package information, practical layout guidance, engineering comparisons, and drop-in replacement considerations. It is designed to help engineers evaluate bandwidth, slew rate, output drive, feedback-network behavior, and PCB implementation requirements before integrating the amplifier into a high-speed analog signal chain.

के लिए ड्रॉप-इन विकल्प OPA694ID — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

OPA694UID

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 8-SOIC
Same OPA694 current-feedback amplifier and 8-SOIC electrical function; ordering-code difference is 0% in bandwidth, slew rate, and output-drive ratings

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

OPA694IDG4

✅ ड्रॉप-इन
📦 8-SOIC
Same OPA694ID amplifier and 8-SOIC footprint; G4 ordering suffix adds a green-material designation with 0% change to stated bandwidth, slew rate, and output drive

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

OPA694IDRG4

✅ ड्रॉप-इन
📦 8-SOIC
Same OPA694ID electrical function and 8-SOIC footprint; R denotes tape-and-reel assembly and G4 denotes green material, with 0% change to stated key performance

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

OPA694IDR

✅ ड्रॉप-इन
📦 8-SOIC
Same OPA694ID electrical function and 8-SOIC footprint; R denotes tape-and-reel assembly, with 0% change to stated bandwidth, slew rate, and output drive

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

OPA694ID Maximum Ratings और Electrical Characteristics

Amplifier Type Current-feedback operational amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 1.5 GHz
Minimum Gain-Bandwidth Product >500 MHz
Slew Rate 1700 V/µs
Output Drive Current ±80 mA
Output Voltage Headroom <1.5 V
Power Class Low-power wideband operational amplifier
Package Type 8-SOIC
Package Width 3.90 mm
Package Body Length 0.154 in
माउंटिंग प्रकार Surface mount
Packaging Tube

OPA694ID पिन कॉन्फ़िगरेशन

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
पिन 1 NC — Not connected (per datasheet)
पिन 2 -IN — Inverting input
पिन 3 +IN — Non-inverting input
पिन 4 V- — Negative supply connection
पिन 5 NC — Not connected (per datasheet)
पिन 6 OUT — Amplifier output
पिन 7 V+ — Positive supply connection
पिन 8 NC — Not connected (per datasheet)

सामान्य अनुप्रयोग

OPA694ID के लिए उपयुक्त है 6 अनुप्रयोगs: High-Density Video Routing, Broadcast and Surveillance Video, Communications Signal Conditioning, High-Speed Test and Measurement, Wideband Active Filters, Imaging and Sensor Interfaces.

📺

High-Density Video Routing

The OPA694ID is well suited to high-density video routing because its more than 500 MHz bandwidth preserves fast video transitions while its 1700 V/µs slew rate supports large-signal swing. Approximately ±80 mA of output drive and less than 1.5 V of headroom help the amplifier drive downstream routing and termination networks. Place the device close to the video source and load, keep feedback traces short, and use controlled impedance routing to minimize reflections. The main design tradeoff is the current-feedback network, which must be selected from the manufacturer’s gain and feedback-resistance guidance rather than copied from a voltage-feedback amplifier.

🎥

Broadcast and Surveillance Video

OPA694ID applications in broadcast and surveillance equipment benefit from the combination of a 1.5 GHz gain-bandwidth product, 1700 V/µs slew rate, and low-power current-feedback operation. These characteristics support amplification of video waveforms with meaningful edge speed while limiting the electrical load placed on upstream sensor or serializer circuitry. The amplifier can be used in video buffers, gain stages, and distribution paths where low differential gain and phase errors are important. PCB implementation should preserve the wideband balance of the input and feedback paths and provide local supply bypassing to prevent supply noise from appearing in the output.

🌐

Communications Signal Conditioning

The OPA694ID fits communications signal-conditioning blocks that require accurate handling of high-speed waveforms. Its 1.5 GHz gain-bandwidth product provides useful bandwidth margin, while the 1700 V/µs slew rate allows the output to follow large input transitions without excessive distortion. The approximately ±80 mA output drive is also relevant when the amplifier drives mixers, filters, or other finite-impedance stages. Because this is a current-feedback amplifier, engineers should select the feedback resistor from the manufacturer’s curves for the required closed-loop gain and verify common-mode range, supply headroom, and output swing against the communications waveform.

🔧

High-Speed Test and Measurement

OPA694ID instrumentation is appropriate for oscilloscope drivers, arbitrary waveform output paths, active probes, and wideband test fixtures requiring rapid slew capability. The 1700 V/µs slew rate and 1.5 GHz gain-bandwidth product allow the amplifier to preserve large-amplitude, fast-edge signals more effectively than lower-bandwidth general-purpose op amps. The less-than-1.5 V output-headroom specification helps support operation near the output-voltage limits of the selected supplies. Keep the amplifier within its specified output-current capability, terminate unused inputs appropriately, and use very short feedback connections so parasitic capacitance does not degrade rise time or stability.

📡

Wideband Active Filters

The OPA694ID can implement high-order or wideband active-filter stages where the 1.5 GHz gain-bandwidth product and 1700 V/µs slew rate provide useful operating margin. Current feedback is especially useful in filters with changing closed-loop gain because its bandwidth is less strongly dependent on gain than that of a conventional voltage-feedback amplifier. However, the feedback impedance and compensation components strongly influence both response and stability, so the complete filter response should be simulated with the intended source and load impedances. Place filter components close to the amplifier and keep the high-impedance summing node as compact as possible.

🖥️

Imaging and Sensor Interfaces

OPA694ID signal paths are suitable for fast imaging and sensor-interface stages that need to process rapidly changing analog waveforms. Its more than 500 MHz bandwidth, 1.5 GHz gain-bandwidth product, and low-power current-feedback architecture provide a useful combination of speed and manageable system loading. The approximately ±80 mA output drive can support downstream stages requiring moderate current, although the exact load must remain within the amplifier’s limits. Design the input network for the sensor’s source impedance, verify the common-mode range for sensor output excursions, and use short ground returns to prevent return-path noise from coupling into the high-gain signal chain.

What is the OPA694ID?
The OPA694ID is a single wideband, low-power, current-feedback operational amplifier from Texas Instruments. It combines a 1.5 GHz gain-bandwidth product, a 1700 V/µs slew rate, more than 500 MHz bandwidth, and approximately ±80 mA of output drive in an 8-pin SOIC package. According to the Texas Instruments OPA694 product information, its low differential gain and phase errors make it suitable for high-density video routing, communications, and precision analog signal chains.
Where can I download the OPA694ID datasheet PDF?
The official OPA694ID datasheet and product information are available from the Texas Instruments product page at https://www.ti.com/product/OPA694, with the ordering-information page at https://www.ti.com/product/OPA694/part-details/OPA694ID. These pages contain the manufacturer’s electrical characteristics, pin configuration, ordering information, and application guidance. Use the manufacturer’s pin-description table when assigning PCB tracks because the SOIC lead numbering must match the selected package drawing.
Where can I find the OPA694ID pinout?
The OPA694ID pinout is shown in the Texas Instruments OPA694 datasheet and uses the standard single-amplifier 8-SOIC arrangement: pin 1 is NC, pin 2 is the inverting input, pin 3 is the non-inverting input, pin 4 is the negative supply, pin 5 is NC, pin 6 is the output, pin 7 is the positive supply, and pin 8 is NC. Follow the pin-description table in the manufacturer datasheet when laying out the PCB or wiring a prototype.
What are the key specifications of OPA694ID that engineers should know?
The principal OPA694ID specifications are a 1.5 GHz gain-bandwidth product, a 1700 V/µs slew rate, more than 500 MHz bandwidth, and approximately ±80 mA of output drive. The device is a single current-feedback amplifier in an 8-SOIC package and operates as a low-power wideband part. According to the Texas Instruments OPA694 product information, the output stage requires less than 1.5 V of headroom, which supports large-signal operation in video and communications equipment.
Is OPA694ID suitable for video applications?
Yes, the OPA694ID is suitable for high-speed video buffering and routing because it provides more than 500 MHz bandwidth, a 1700 V/µs slew rate, and approximately ±80 mA of output drive. According to the Texas Instruments OPA694 product information, its low supply current and less-than-1.5 V output headroom meet the requirements of high-density video routers. PCB layout must still minimize feedback-node capacitance and maintain controlled return paths.
What is the difference between OPA694ID and OPA694IDR?
The OPA694ID and OPA694IDR provide the same OPA694 amplifier in different orderable packaging arrangements: OPA694ID is supplied in a tube, while OPA694IDR is the tape-and-reel ordering option. The OPA694ID listing identifies an 8-SOIC package and one current-feedback amplifier circuit. Because the electrical device and PCB land pattern are the same, OPA694IDR is a procurement and assembly alternative when reel packaging is required.
OPA694ID vs OPA828ID: which is better for a high-speed amplifier?
The OPA694ID is the clearer choice when low power and a current-feedback architecture are priorities, while the OPA828ID is an alternative high-speed operational amplifier that may suit designs requiring a different voltage-feedback implementation. The OPA694ID provides a 1.5 GHz gain-bandwidth product and 1700 V/µs slew rate in an 8-SOIC package. Final selection should compare supply range, noise, distortion, output swing, feedback resistors, and stability for the intended gain.
When should I choose OPA694ID over a lower-bandwidth amplifier?
Choose the OPA694ID when the signal path needs more than 500 MHz bandwidth, 1700 V/µs slew rate, or approximately ±80 mA of output drive. These characteristics are important for video routing, communications, active filtering, and high-speed instrumentation. A lower-bandwidth amplifier may be preferable only when its lower power consumption and simpler voltage-feedback compensation are more important than large-signal bandwidth.
Is OPA694ID suitable for a high-speed instrumentation amplifier?
Yes, the OPA694ID can fit high-speed instrumentation stages that require a 1.5 GHz gain-bandwidth product and 1700 V/µs slew rate. Its current-feedback topology is especially useful when several gain settings must be supported, because bandwidth changes less dramatically with closed-loop gain than in a conventional voltage-feedback amplifier. The actual noise, offset, input-impedance, and accuracy requirements must still be checked against the complete signal path.
What can replace the OPA694ID?
The OPA694ID can be replaced without PCB changes by OPA694 orderable variants that use the same 8-SOIC footprint and retain the same amplifier function. The OPA694UID is the closest same-family choice because it preserves the OPA694 current-feedback architecture and pin arrangement. Because current-feedback amplifiers are sensitive to feedback impedance, replacement should be verified against the original feedback resistor, gain setting, supply voltage, and required bandwidth.
What is the best Analog Devices equivalent for OPA694ID?
No Analog Devices drop-in replacement can be selected responsibly from the available cross-reference information because it does not identify a candidate MPN with a verified 8-SOIC pin arrangement and comparable specifications. A functional equivalent is not automatically a drop-in replacement for a current-feedback amplifier. Request a specific Analog Devices candidate and verify its package, pinout, feedback network, bandwidth, slew rate, supply range, output drive, and stability before substitution.
How should the feedback resistor be chosen for OPA694ID?
Choose the OPA694ID feedback resistor from the manufacturer’s recommended feedback resistance versus closed-loop gain curves rather than applying the usual voltage-feedback formula mechanically. A resistance near 1 kΩ is a common starting point for many current-feedback amplifiers, but the optimum value depends on gain, bandwidth, output loading, and the number of feedback components. Preserve the recommended topology and keep the feedback node physically compact.
How should I lay out an OPA694ID PCB for high-speed operation?
Place input, feedback, and bypass components directly beside their associated OPA694ID pins, and route supply and ground connections with minimal inductance. Keep the inverting-input and feedback-node traces short to reduce parasitic capacitance that can disturb stability and isolation. Connect input and output grounds to a low-impedance plane, avoid splits beneath the amplifier, and verify the final layout with signal-integrity measurements if large-signal performance is critical.
Can OPA694ID operate from dual supplies?
The OPA694ID is designed for dual-supply operation, but the permitted supply-voltage range must be confirmed from the Texas Instruments datasheet before applying either rail. Its output stage provides approximately ±80 mA of drive with less than 1.5 V of output headroom, so each supply rail must leave adequate voltage range for the required output swing. Input common-mode voltage and output-swing limits also need to be checked against the actual signal.
Where can I buy OPA694ID and check its current lead time?
Use the Request a Quote form on this page to inquire about OPA694ID availability, current lead time, order quantity, and tube-packaging requirements. The manufacturer lists the OPA694 family through Texas Instruments, and distributor records identify OPA694ID as an 8-SOIC current-feedback amplifier. Because stock and lead time change by region and order volume, request the current commitment rather than relying on a historical listing snapshot.

के लिए इंजीनियरिंग संदर्भ डेटा OPA694ID — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the OPA694ID for wideband video, communications, imaging, and instrumentation paths that benefit from a 1.5 GHz gain-bandwidth product, 1700 V/µs slew rate, and approximately ±80 mA of output drive. Its current-feedback architecture is valuable when closed-loop gain changes, but it requires feedback-resistor selection from the manufacturer’s guidance and careful PCB control around the inverting input. OPA694UID is the closest same-family replacement when a different ordering code is required. OPA694IDR, OPA694IDG4, and OPA694IDRG4 retain the same amplifier and 8-SOIC footprint while supporting tube, reel, or green-material ordering needs. If a different amplifier architecture is preferred, compare the OPA828ID and other high-speed devices against supply range, noise, distortion, input impedance, output swing, and feedback-network requirements before changing the PCB.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद OPA694UID OPA694IDG4 OPA694IDRG4 OPA694IDR
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Architecture Current feedback Current feedback Current feedback Current feedback Current feedback
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Gain-Bandwidth Product 1.5 GHz 1.5 GHz 1.5 GHz 1.5 GHz 1.5 GHz
Slew Rate 1700 V/µs 1700 V/µs 1700 V/µs 1700 V/µs 1700 V/µs
Output Drive Current ±80 mA ±80 mA ±80 mA ±80 mA ±80 mA
Output Voltage Headroom <1.5 V <1.5 V <1.5 V <1.5 V <1.5 V
Power Class Low power Low power Low power Low power Low power
Differential Gain and Phase Error Low Low Low Low Low

मुख्य विशेषताएँ

  • High-speed current-feedback performance in a low-power package (बनामOPA828ID)
  • Identical electrical ordering variants support assembly flexibility (बनामOPA694IDR)
  • Large-signal output capability with low headroom (बनामOPA694IDG4)

डिज़ाइन नोट्स

Keep the OPA694ID feedback resistor, inverting-input connection, and compensation components directly adjacent to the amplifier pins. The current-feedback input node is sensitive to parasitic capacitance, and long or asymmetric traces can reduce stability or alter channel behavior. Use short supply pins, place bypass capacitors at the pins, and provide a continuous ground plane so high-frequency return current does not cross a split in the reference plane.

Do not substitute a conventional voltage-feedback compensation network without simulation. The OPA694ID’s current-feedback bandwidth depends on feedback impedance, so the manufacturer’s gain-versus-feedback-resistance guidance should determine the resistor value. Preserve balanced input routing and avoid adding capacitance to the inverting input. Validate rise time, overshoot, and stability at the intended closed-loop gain using the final source impedance and load.

Confirm that both supply rails provide the required output headroom and that the load does not exceed the approximately ±80 mA output-drive capability. Because the output stage requires less than 1.5 V of headroom, adequate rail voltage is still necessary for the desired waveform swing. Use separate local bypassing paths for each supply pin and keep the negative-supply return close to the device to minimize supply-inductor effects at high slew rate.

A common OPA694ID mistake is assuming that a 1 kΩ feedback resistor is universal. Feedback resistance must be coordinated with closed-loop gain, bandwidth, output loading, and topology. Another common mistake is leaving the NC pins physically unrouted without checking the package drawing. Verify the pin-description table, termination networks, output load, and supply sequencing before releasing the PCB layout.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The manufacturer product information and listed orderable variants do not explicitly state the requested compliance statuses. AEC-Q100 qualification is not applicable to the identified catalog ordering options.

डेटा सत्यापन तिथि: 2026-11-19 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

OPA694ID datasheet OPA694ID datasheet pdf OPA694ID pinout OPA694ID specifications OPA694ID 8-SOIC OPA694ID 1.5GHz OPA694ID equivalent OPA694ID replacement OPA694ID vs OPA828ID OPA694ID video amplifier OPA694ID price OPA694ID stock Texas Instruments OPA694ID

संबंधित कंपोनेंट्स और शब्द

Texas Instruments OPA694ID OPA694UID OPA694IDR OPA694IDG4 OPA694IDRG4 OPA828ID current-feedback operational amplifier operational amplifier amplifier IC semiconductor gain-bandwidth product slew rate output drive current output voltage headroom differential gain error differential phase error feedback impedance 8-SOIC SOIC family surface-mount package video routing communications signal conditioning test and measurement
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें