OPA694ID - 1.5GHz Wideband Op Amp | Texas Instruments
MPN: OPA694ID ✓ AktifOPA694ID Genel Bakış
A current-feedback operational amplifier is a voltage-feedback amplifier subclass whose feedback impedance determines closed-loop bandwidth and gain. Unlike a conventional voltage-feedback amplifier, a current-feedback amplifier maintains relatively stable bandwidth as closed-loop gain changes. This behavior is valuable in wideband systems where gain is adjusted across multiple stages, particularly when low differential gain and phase errors are important for maintaining signal integrity.
The OPA694ID combines more than 500 MHz bandwidth with low supply current, high slew rate, and strong output-drive capability. Its ±80 mA output stage can drive lower-impedance loads and downstream circuitry while retaining less than 1.5 V of headroom. The 1700 V/µs slew rate supports rapid transitions required by video routers, waveform generators, active filters, and high-speed instrumentation. The single-amplifier configuration also keeps board area and external component requirements compact.
Because the OPA694ID uses current feedback, feedback-network selection requires more care than with voltage-feedback amplifiers. A conventional 1 kΩ feedback resistor is often appropriate for modest gain, but the exact value should follow the manufacturer’s gain-versus-feedback-resistance guidance for the required closed-loop gain. Board parasitics, package inductance, and long feedback traces can materially affect isolation and stability at these bandwidths.
Typical applications include high-density video routing, broadcast and surveillance video systems, analog test equipment, communications receivers, and wideband active filters. In a video buffer, it can preserve large-signal swing while offering more than 500 MHz bandwidth. In instrumentation, its 1.5 GHz gain-bandwidth product supports amplification stages that must retain low distortion and timing accuracy.
Use short, impedance-controlled PCB traces, maintain symmetric routing around the amplifier, and place compensation or feedback components close to the relevant pins. Decoupling capacitors should connect directly between each supply pin and ground with a low-impedance return path. Avoid long loops around high-speed feedback nodes and test the completed layout with time-domain reflectometry or equivalent signal-integrity equipment.
This page combines the OPA694ID’s core electrical characteristics with package information, practical layout guidance, engineering comparisons, and drop-in replacement considerations. It is designed to help engineers evaluate bandwidth, slew rate, output drive, feedback-network behavior, and PCB implementation requirements before integrating the amplifier into a high-speed analog signal chain.
Drop-in alternatifler için OPA694ID — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
OPA694UID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
OPA694IDG4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
OPA694IDRG4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
OPA694IDR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
OPA694ID Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Current-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 1.5 GHz |
| Minimum Gain-Bandwidth Product | >500 MHz |
| Slew Rate | 1700 V/µs |
| Output Drive Current | ±80 mA |
| Output Voltage Headroom | <1.5 V |
| Power Class | Low-power wideband operational amplifier |
| Package Type | 8-SOIC |
| Package Width | 3.90 mm |
| Package Body Length | 0.154 in |
| Montaj Türü | Surface mount |
| Packaging | Tube |
OPA694ID Pin Yapısı
| Pin 1 | NC — Not connected (per datasheet) |
| Pin 2 | -IN — Inverting input |
| Pin 3 | +IN — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected (per datasheet) |
| Pin 6 | OUT — Amplifier output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected (per datasheet) |
Tipik Uygulamalar
OPA694ID için uygundur 6 uygulamas: High-Density Video Routing, Broadcast and Surveillance Video, Communications Signal Conditioning, High-Speed Test and Measurement, Wideband Active Filters, Imaging and Sensor Interfaces.
High-Density Video Routing
The OPA694ID is well suited to high-density video routing because its more than 500 MHz bandwidth preserves fast video transitions while its 1700 V/µs slew rate supports large-signal swing. Approximately ±80 mA of output drive and less than 1.5 V of headroom help the amplifier drive downstream routing and termination networks. Place the device close to the video source and load, keep feedback traces short, and use controlled impedance routing to minimize reflections. The main design tradeoff is the current-feedback network, which must be selected from the manufacturer’s gain and feedback-resistance guidance rather than copied from a voltage-feedback amplifier.
Önerilen
Broadcast and Surveillance Video
OPA694ID applications in broadcast and surveillance equipment benefit from the combination of a 1.5 GHz gain-bandwidth product, 1700 V/µs slew rate, and low-power current-feedback operation. These characteristics support amplification of video waveforms with meaningful edge speed while limiting the electrical load placed on upstream sensor or serializer circuitry. The amplifier can be used in video buffers, gain stages, and distribution paths where low differential gain and phase errors are important. PCB implementation should preserve the wideband balance of the input and feedback paths and provide local supply bypassing to prevent supply noise from appearing in the output.
Önerilen
Communications Signal Conditioning
The OPA694ID fits communications signal-conditioning blocks that require accurate handling of high-speed waveforms. Its 1.5 GHz gain-bandwidth product provides useful bandwidth margin, while the 1700 V/µs slew rate allows the output to follow large input transitions without excessive distortion. The approximately ±80 mA output drive is also relevant when the amplifier drives mixers, filters, or other finite-impedance stages. Because this is a current-feedback amplifier, engineers should select the feedback resistor from the manufacturer’s curves for the required closed-loop gain and verify common-mode range, supply headroom, and output swing against the communications waveform.
Önerilen
High-Speed Test and Measurement
OPA694ID instrumentation is appropriate for oscilloscope drivers, arbitrary waveform output paths, active probes, and wideband test fixtures requiring rapid slew capability. The 1700 V/µs slew rate and 1.5 GHz gain-bandwidth product allow the amplifier to preserve large-amplitude, fast-edge signals more effectively than lower-bandwidth general-purpose op amps. The less-than-1.5 V output-headroom specification helps support operation near the output-voltage limits of the selected supplies. Keep the amplifier within its specified output-current capability, terminate unused inputs appropriately, and use very short feedback connections so parasitic capacitance does not degrade rise time or stability.
Önerilen
Wideband Active Filters
The OPA694ID can implement high-order or wideband active-filter stages where the 1.5 GHz gain-bandwidth product and 1700 V/µs slew rate provide useful operating margin. Current feedback is especially useful in filters with changing closed-loop gain because its bandwidth is less strongly dependent on gain than that of a conventional voltage-feedback amplifier. However, the feedback impedance and compensation components strongly influence both response and stability, so the complete filter response should be simulated with the intended source and load impedances. Place filter components close to the amplifier and keep the high-impedance summing node as compact as possible.
Önerilen
Imaging and Sensor Interfaces
OPA694ID signal paths are suitable for fast imaging and sensor-interface stages that need to process rapidly changing analog waveforms. Its more than 500 MHz bandwidth, 1.5 GHz gain-bandwidth product, and low-power current-feedback architecture provide a useful combination of speed and manageable system loading. The approximately ±80 mA output drive can support downstream stages requiring moderate current, although the exact load must remain within the amplifier’s limits. Design the input network for the sensor’s source impedance, verify the common-mode range for sensor output excursions, and use short ground returns to prevent return-path noise from coupling into the high-gain signal chain.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: OPA694ID — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | OPA694UID | OPA694IDG4 | OPA694IDRG4 | OPA694IDR |
|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Architecture | Current feedback | Current feedback | Current feedback | Current feedback | Current feedback |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 1.5 GHz | 1.5 GHz | 1.5 GHz | 1.5 GHz | 1.5 GHz |
| Slew Rate | 1700 V/µs | 1700 V/µs | 1700 V/µs | 1700 V/µs | 1700 V/µs |
| Output Drive Current | ±80 mA | ±80 mA | ±80 mA | ±80 mA | ±80 mA |
| Output Voltage Headroom | <1.5 V | <1.5 V | <1.5 V | <1.5 V | <1.5 V |
| Power Class | Low power | Low power | Low power | Low power | Low power |
| Differential Gain and Phase Error | Low | Low | Low | Low | Low |
Ana Farklılayıcılar
- High-speed current-feedback performance in a low-power package (karşılaştırma:OPA828ID)
- Identical electrical ordering variants support assembly flexibility (karşılaştırma:OPA694IDR)
- Large-signal output capability with low headroom (karşılaştırma:OPA694IDG4)
Tasarım Notları
Keep the OPA694ID feedback resistor, inverting-input connection, and compensation components directly adjacent to the amplifier pins. The current-feedback input node is sensitive to parasitic capacitance, and long or asymmetric traces can reduce stability or alter channel behavior. Use short supply pins, place bypass capacitors at the pins, and provide a continuous ground plane so high-frequency return current does not cross a split in the reference plane.
Do not substitute a conventional voltage-feedback compensation network without simulation. The OPA694ID’s current-feedback bandwidth depends on feedback impedance, so the manufacturer’s gain-versus-feedback-resistance guidance should determine the resistor value. Preserve balanced input routing and avoid adding capacitance to the inverting input. Validate rise time, overshoot, and stability at the intended closed-loop gain using the final source impedance and load.
Confirm that both supply rails provide the required output headroom and that the load does not exceed the approximately ±80 mA output-drive capability. Because the output stage requires less than 1.5 V of headroom, adequate rail voltage is still necessary for the desired waveform swing. Use separate local bypassing paths for each supply pin and keep the negative-supply return close to the device to minimize supply-inductor effects at high slew rate.
A common OPA694ID mistake is assuming that a 1 kΩ feedback resistor is universal. Feedback resistance must be coordinated with closed-loop gain, bandwidth, output loading, and topology. Another common mistake is leaving the NC pins physically unrouted without checking the package drawing. Verify the pin-description table, termination networks, output load, and supply sequencing before releasing the PCB layout.
Uyumluluk Bilgisi
The manufacturer product information and listed orderable variants do not explicitly state the requested compliance statuses. AEC-Q100 qualification is not applicable to the identified catalog ordering options.