NXP Semiconductors

PCA9511D - Hot-Swappable I2C/SMBus Buffer | NXP

MPN: PCA9511D ✗ जीवन की समाप्ति
2.7 V to 5.5 V Vdss 8-pin SOIC Package 400 kHz Speed
न्यूनतम ऑर्डर मात्रा: 1 |

PCA9511D अवलोकन

The NXP Semiconductors PCA9511D is a one-channel hot-swappable I2C and SMBus bus buffer operating from 2.7 V to 5.5 V, with distributor listings identifying a 400 kHz bus speed and an 8-pin SOIC package. It is intended for systems where removable cards connect to, or disconnect from, an operating I2C or SMBus backplane without corrupting the data and clock buses.

A hot-swappable bus buffer is an interface IC that isolates two bus segments while a card is inserted or removed. Its control circuitry prevents electrical disturbance from the newly connected or disconnected card from propagating across the active bus. Within the interface hierarchy, the PCA9511D belongs to the I2C and SMBus buffer class, which sits beneath bus transceivers and broader interface ICs used to protect, isolate, or route communications links.

The principal device characteristics are a 2.7 V to 5.5 V supply range, support for I2C and SMBus signaling, a nominal 400 kHz operating rate, and an 8-pin SOIC package. The buffer function allows equipment makers to use the same backplane architecture across cPCI, VME, AdvancedTCA, and similar multipoint backplane systems where field-replaceable cards may be inserted into a running system.

The PCA9511D separates the bus side connected to the insertion or removal event from the host-side communication path. This isolation is functionally important because connector transients and card power-state transitions can otherwise disturb clock and data waveforms. The NXP product page identifies the device as discontinued, so it should be treated as a legacy component for maintenance, repair, and previously qualified system support rather than a new-design preference.

Typical uses include hot-pluggable cPCI and VME controller cards, AdvancedTCA line cards, embedded backplane interfaces, and other I2C or SMBus systems that require controlled card insertion or removal. The 400 kHz bus designation also places the device in legacy low-speed bus applications rather than newer high-speed I2C designs.

When designing around the PCA9511D, preserve the bus-side and card-side separation described by the manufacturer datasheet, validate connector and card power-up sequencing, and verify signal integrity in the completed backplane. PCB changes are generally unnecessary when replacing the same 8-pin SOIC device, but functional and lifecycle qualification must precede substitution.

This product record combines lifecycle, electrical, package, sourcing, cross-reference, and replacement guidance with practical hot-plug design considerations. It also distinguishes true pin-to-pin options from superficially similar I2C switches and multiplexers that require different control, channel-count, or bus-isolation behavior.

के लिए ड्रॉप-इन विकल्प PCA9511D — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं PCA9511D (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type.

NXP Semiconductors
Package: 8-SO, 8 pins
Product Type: Hot-swappable I2C-bus and SMBus buffer
इसके साथ तुलना करें PCA9511D →

इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।

विकल्प अनुरोध करें

PCA9511D विशेषताएं

Product Type Hot-swappable I2C and SMBus bus buffer
Channel Count 1 channel
Supply Voltage Range 2.7 V to 5.5 V
Nominal Bus Speed 400 kHz
Supported Interfaces I2C and SMBus
Hot-Swap Capability Yes
पैकेज 8-pin SOIC
माउंटिंग प्रकार Surface mount
Output Buffer Type I2C bus and SMBus switch
लाइफसाइकिल स्थिति Discontinued

PCA9511D 8-pin soic पिन कॉन्फ़िगरेशन गाइड

PCA9511D (8-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

PCA9511D के लिए 8-pin soic पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: PCA9511D.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

PCA9511D के लिए उपयुक्त है 6 अनुप्रयोगs: Hot-Pluggable CPCI Backplane Cards, VME Card Insertion Control, AdvancedTCA Line-Card Interface, Embedded Hot-Swap Control Bus, Instrumentation Module Interconnect, Legacy Communication Equipment Repair.

🖥️

Hot-Pluggable CPCI Backplane Cards

The PCA9511D fits a cPCI card interface that may be inserted into or removed from an operating backplane. Its hot-swappable I2C and SMBus buffer function is intended to keep disturbance from the card connection event from corrupting the active data and clock buses. With a 2.7 V to 5.5 V supply range and a one-channel architecture, it is appropriate for legacy cPCI management paths operating at the 400 kHz class. The implementation should follow the manufacturer application circuit, preserve bus isolation, and validate connector transitions, card power states, and signal integrity in the assembled chassis.

🖥️

VME Card Insertion Control

The PCA9511D is suited to VME backplane management interfaces where card insertion or removal must not corrupt an active I2C or SMBus segment. The one-channel buffer provides a controlled isolation point between the host side and card side of the interface while the card is connected or disconnected. Its 2.7 V to 5.5 V operating range supports common legacy embedded-system supply levels, while the 400 kHz designation matches low-speed management-bus requirements. Validate the final design against the manufacturer hot-plug circuit, including startup sequencing, connector bounce, bus capacitance, and card power-state behavior during insertion.

🏭

AdvancedTCA Line-Card Interface

The PCA9511D can support legacy AdvancedTCA line-card systems in which a management interface must tolerate card removal from a live backplane. Its hot-swappable I2C and SMBus buffer architecture is intended to prevent connection-related disturbance from propagating into the operating bus. The one-channel implementation, 2.7 V to 5.5 V supply, and 400 kHz operating class align with low-speed administrative links rather than high-speed differential payloads. Before release, reproduce the manufacturer's application topology and verify isolation timing, power sequencing, connector behavior, and channel capacitance across the complete platform.

🔧

Embedded Hot-Swap Control Bus

The PCA9511D is appropriate for an embedded controller that exchanges I2C or SMBus management information with a removable expansion module. Its hot-swappable buffer behavior is designed to protect the active host bus when the module is inserted or extracted, reducing the risk that connector transients or card-state changes corrupt clock and data. The 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V legacy systems, and the one-channel arrangement suits a single isolated expansion path. The circuit must follow the manufacturer hot-plug example and be tested with realistic connector transitions, card power-up sequences, and bus loading.

🧩

Instrumentation Module Interconnect

The PCA9511D can isolate a removable instrumentation module's I2C or SMBus management connection from a host controller that remains active during service or reconfiguration. This is useful where the module may be connected without shutting down the measurement system and where bus corruption could disrupt calibration, configuration, or status reporting. The device's one-channel architecture and 400 kHz class are appropriate for low-speed control traffic, while its 2.7 V to 5.5 V supply range supports common embedded supply rails. Confirm timing, enable behavior, capacitance, and supply sequencing in the manufacturer application circuit before production use.

🌐

Legacy Communication Equipment Repair

The PCA9511D is relevant to repair and maintenance of legacy communication equipment with hot-pluggable I2C or SMBus cards. Its documented one-channel buffer function allows an original motherboard to retain the intended isolation behavior when a failed device must be replaced. Because NXP identifies the part as discontinued, procurement should require exact package marking, date code, condition, and traceability. Technical interchangeability must be established through pin, timing, supply-voltage, enable-state, and hot-swap comparisons rather than package appearance alone. Request the legacy part through the Request a Quote form on this page.

अनुशंसित उत्पादों का सारांश

PCA9511D,112 Commercial ordering code for the PCA9511D device उपयोग में: Hot-Pluggable CPCI Backplane Cards, VME Card Insertion Control, AdvancedTCA Line-Card Interface, Embedded Hot-Swap Control Bus, Instrumentation Module Interconnect, Legacy Communication Equipment Repair PCA9511D,118 Commercial ordering code for the PCA9511D device उपयोग में: Hot-Pluggable CPCI Backplane Cards, VME Card Insertion Control, AdvancedTCA Line-Card Interface, Embedded Hot-Swap Control Bus, Instrumentation Module Interconnect, Legacy Communication Equipment Repair
What is the PCA9511D?
The PCA9511D is a one-channel hot-swappable I2C and SMBus bus buffer made by NXP Semiconductors. According to the NXP product page, it is intended to permit card insertion and removal from a live backplane without corrupting the data or clock buses. It operates from 2.7 V to 5.5 V, is associated with a 400 kHz bus rate, and is offered in an 8-pin SOIC package.
What voltage does the PCA9511D operate from?
The PCA9511D operates from 2.7 V to 5.5 V. This range supports both 3.3 V and 5 V system environments, although the host and card interfaces must still be checked for compatible logic levels. The NXP manufacturer documentation identifies the device as a hot-swappable I2C and SMBus buffer with one channel and an 8-pin SOIC package.
Where can I download the PCA9511D datasheet PDF?
The official PCA9511D product documentation is available from the NXP product page at https://www.nxp.com/products/PCA9511D. The page links to the manufacturer datasheet and historical product information. Use the manufacturer PDF for the authoritative pin description, timing limits, electrical characteristics, application circuit, and hot-plug behavior before laying out or qualifying a replacement board.
Where can I find the PCA9511D pinout?
The PCA9511D uses an 8-pin SOIC package, but a complete numbered pin list is not available in the retrieved product summaries. Use the pin-description table and package drawing in the NXP manufacturer datasheet when assigning PCB nets. In particular, verify the bus-side, card-side, supply, ground, and enable-related connections against the exact datasheet revision before fabrication.
Is the PCA9511D still active?
No. The NXP manufacturer page states that the PCA9511D is no longer manufactured and provides its information for historical reference only. It should therefore be treated as an obsolete or discontinued legacy component. New designs should evaluate currently supported interfaces, while maintenance programs can request availability and lot traceability through the Request a Quote form on this page.
Where can I buy PCA9511D online?
Use the Request a Quote form on this page to request the exact PCA9511D device, package marking, quantity, and current availability. Because NXP identifies the PCA9511D as discontinued, procurement should include a written lifecycle and traceability statement. Do not assume that a similarly named interface IC has equivalent hot-swap behavior without checking its datasheet and pin configuration.
What is the price of PCA9511D?
Current PCA9511D pricing is shown through the Request a Quote form on this page and can change as legacy inventory is sourced. The structured price fields are intended for live catalog and inventory feeds, so request a formal quotation for production quantities. For an obsolete device, specify the manufacturer part number, package marking, date code, inspection requirements, and traceability documents with the request.
What is the lead time for PCA9511D?
The current lead time for the discontinued PCA9511D should be confirmed through the Request a Quote form on this page. Legacy availability can vary by lot, date code, and remaining inventory, so a nominal delivery estimate is not sufficient for production planning. Request a lot-specific commitment and include the required quantity, acceptable date-code range, package condition, and inspection level.
Is PCA9511D in stock?
Stock status for the discontinued PCA9511D must be confirmed through the Request a Quote form on this page. The NXP manufacturer page explicitly states that the device is no longer manufactured, so any remaining supply is legacy inventory rather than normal production replenishment. For maintenance use, request date-code details and traceability so inventory can be evaluated against the qualification requirements of the system.
What can replace PCA9511D?
A valid PCA9511D replacement must be an 8-pin SOIC device with matching pin assignments, the same 2.7 V to 5.5 V operating range, equivalent I2C and SMBus hot-swap behavior, and acceptable 400 kHz bus performance. No cross-brand device in the retrieved cross-reference records establishes all of these requirements. Use the Request a Quote form to request an engineering review of exact candidate MPNs.
Is PCA9511D the same as PCA9512AD?
No. The PCA9511D is a one-channel hot-swappable I2C and SMBus buffer rated for a 2.7 V to 5.5 V supply and a 400 kHz bus. Cross-reference information lists the PCA9512AD as a related product but not an identical device. A physical 8-pin package match does not establish functional equivalence, so verify channel count, isolation behavior, enable logic, timing, and pin assignments before considering a substitution.
PCA9511D vs PCA9512AD — which is better for a live backplane?
The PCA9511D is the better-defined choice when the requirement specifically calls for one-channel hot-swappable I2C or SMBus operation. The PCA9512AD is a related PCA-family interface device, but the retrieved cross-reference information does not establish identical hot-swap isolation or control behavior. The PCA9511D should therefore be selected for a qualified legacy design unless the alternative's datasheet proves equivalent operation.
When should I choose PCA9511D over PCA9512AD?
Choose the PCA9511D when a previously designed system requires its documented one-channel hot-swap buffer function, 2.7 V to 5.5 V supply range, and 400 kHz operating class. Choose the PCA9512AD only when its own datasheet confirms that its channel arrangement, enable controls, isolation behavior, timing, and pinout satisfy the system. Package similarity alone is not sufficient for a drop-in decision.
Is PCA9511D suitable for hot-plug backplane cards?
Yes, the PCA9511D is specifically described as a hot-swappable I2C and SMBus bus buffer for live card insertion and removal. Its one-channel architecture and control circuitry are suited to isolating disturbance caused by card connection events. Final suitability still depends on matching the card-side and bus-side interfaces, supply sequencing, connector behavior, and the complete system timing in the manufacturer application circuit.
What are the key specifications of PCA9511D that engineers should know?
The key PCA9511D specifications are a 2.7 V to 5.5 V operating supply, one buffered channel, I2C and SMBus support, a nominal 400 kHz bus rate, hot-swap capability, and an 8-pin SOIC package. The device is also discontinued according to NXP. Detailed timing, electrical limits, enable behavior, and pin assignments must be taken from the manufacturer datasheet for design release and substitution review.

के लिए इंजीनियरिंग संदर्भ डेटा PCA9511D — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the PCA9511D when maintaining or reproducing a legacy system that specifically requires a one-channel hot-swappable I2C or SMBus buffer at the 400 kHz class. Its 2.7 V to 5.5 V range and 8-pin SOIC package fit common legacy backplane arrangements, but the manufacturer datasheet must define the final connections and controls. Do not select PCA9512AD or PCA9543ADR merely because they also use 8-pin packages; their retrieved records indicate related interface functions rather than verified equivalent hot-swap behavior. For new products, the discontinued lifecycle status makes a currently supported interface solution preferable. For repair of an original design, exact package marking, timing behavior, supply range, and traceability should be verified before approval. If no fully qualified substitute exists, preserving the original architecture and sourcing an authentic PCA9511D is the lower-risk path.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद
Package 8-pin SOIC
Brand NXP Semiconductors
Product Type Hot-swappable I2C and SMBus bus buffer
Channel Count 1 channel
Supply Voltage Range 2.7 V to 5.5 V
Nominal Bus Speed 400 kHz
Hot-Swap Capability Yes
Lifecycle Status Discontinued

मुख्य विशेषताएँ

  • Purpose-built hot-swap isolation (बनामPCA9512AD)
  • Defined legacy backplane role (बनामPCA9543ADR)
  • One-channel focused implementation (बनामPCA9512AD)

डिज़ाइन नोट्स

Route the bus-side and card-side I2C or SMBus paths as separate nets terminated only at the locations specified by the manufacturer application circuit. Keep the buffer close to the connector or card interface and preserve the isolation topology, because long shared copper paths can allow card-insertion transients to reach the active bus. Match trace geometry where possible and verify that the card-side stub does not create timing or capacitance problems during hot insertion.

Design the 2.7 V to 5.5 V supply path so the PCA9511D remains within its operating range during card insertion, removal, and system startup. Include local supply decoupling as specified in the manufacturer datasheet and keep the return path continuous when connector and card ground states change. Validate sequencing with the actual connector, backplane, and card because a nominal operating range alone does not guarantee correct hot-swap behavior.

Do not treat a generic 8-pin I2C switch or multiplexer as a direct substitute for the PCA9511D. Pin position, enable polarity, channel count, bus-side isolation, operating range, and hot-swap timing must all agree with the manufacturer datasheet. For the discontinued target, preserve the original schematic and verify any proposed substitute across insertion, removal, idle, bus traffic, and supply-ramp conditions before committing it to production.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The manufacturer page identifies PCA9511D as discontinued and no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was confirmed for the exact device.

डेटा सत्यापन तिथि: 2026-11-19 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

PCA9511D PCA9511D datasheet PCA9511D datasheet pdf PCA9511D pinout PCA9511D schematic PCA9511D equivalent PCA9511D replacement PCA9511D cross reference PCA9511D vs PCA9512AD PCA9511D SOIC-8 hot swap buffer PCA9511D price PCA9511D stock NXP PCA9511D PCA9511D backplane application circuit

संबंधित कंपोनेंट्स और शब्द

NXP Semiconductors PCA9511D PCA9511D,112 PCA9511D,118 PCA9512AD PCA9543ADR I2C bus SMBus hot-swappable bus buffer bus buffer interface IC semiconductor one-channel buffer 2.7 V to 5.5 V supply 400 kHz bus speed 8-pin SOIC SOIC family surface mount SMD live backplane cPCI VME AdvancedTCA card insertion bus isolation I2C bus and SMBus switch
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें