PCA9546ADW - 4-Channel I2C/SMBus Translating Switch with Reset | Texas Instruments
MPN: PCA9546ADW ✓ सक्रियPCA9546ADW अवलोकन
An I2C or SMBus bus switch, also called a bus multiplexer or fan-out buffer, is an interface IC that lets one controller talk to several targets that share the same SDA and SCL lines. Structurally, the PCA9546ADW sits in the hierarchy of interface ICs: I2C/SMBus switch -> bus multiplexer -> interface controller -> digital IC -> semiconductor. Instead of separate I2C lines running to every sensor or EEPROM, the upstream bus reaches the switch and the switch routes it to only the selected downstream segment.
Key features include four independently selectable downstream channels, bidirectional pass-gate construction, an active-low RESET input that returns the internal I2C-bus state machine to a known condition and deselects all channels, and an internal power-on reset that performs the same function at startup. Two address pins allow several switch devices to coexist on one bus, and the pass-gate structure allows the VDD pin to limit the maximum high voltage that is passed through the channels.
Technically, the part is a state-machine-controlled multiplexer rather than a repeater. The upstream controller writes a control byte that determines which SCn/SDn channels pass the bus. Because the pass gates are bidirectional, the same device can also be used where the direction of the bus flow changes, and the device does not regenerate or re-time the clock signal. The RESET path is the recovery mechanism of choice when a slave holds SDA low after a brown-out and blocks the bus.
Typical uses include multi-sensor measurement hubs, banks of serial EEPROMs, RTC and PMIC fan-out, LED driver arrays, and industrial acquisition boards that must connect several low-voltage I2C devices to one MCU.
A key design consideration is pull-up placement: the upstream pull-ups belong on the controller side, while each downstream segment needs its own pull-ups if the channel is not connected continuously. Confirm the address-strapping resistors and the RESET trace are routed so a system reset also clears the mux state.
This page consolidates the switching function, reset behavior, pin assignment, drop-in alternatives, and practical layout guidance for the PCA9546ADW into one place, and adds engineering context that is not reproduced in the manufacturer datasheet.
के लिए ड्रॉप-इन विकल्प PCA9546ADW — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं PCA9546ADW (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Address Pins, Number of Channels, Package.
TCA9546ADWR
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
PCA9546AD
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →PCA9546ADW Maximum Ratings और Electrical Characteristics
| Device Type | Quad bidirectional I2C/SMBus translating switch |
| Number of Channels | 4 downstream SCn/SDn channels |
| Upstream Ports | 1 (SCL/SDA) |
| Downstream Ports | 4 (SC0/SD0 through SC3/SD3) |
| Bus Standards Supported | I2C and SMBus |
| Signal Direction | Bidirectional |
| Control Interface | I2C-programmable control register |
| Reset Function | Yes - active-low RESET input deselects all channels and resets the I2C-bus state machine |
| Power-On Reset | Yes - internal POR performs the same deselect action at startup |
| Switch Implementation | Pass gates; VDD pin can limit the maximum high voltage passed through the channels |
| Address Pins | 2 address pins (A0/A1) for multi-switch addressing |
| पैकेज | 16-pin SOIC (DW) |
| पिन काउंट | 16 pins |
| माउंटिंग प्रकार | Surface mount |
PCA9546ADW पिन कॉन्फ़िगरेशन
| पिन 1 | RESET — Active-low reset input; low resets the I2C-bus state machine and deselects all channels |
| पिन 2 | GND — Ground |
| पिन 3 | SCL — Upstream I2C/SMBus clock input |
| पिन 4 | SDA — Upstream I2C/SMBus data input/output |
| पिन 5 | SC0 — Downstream channel 0 clock (bidirectional pass gate) |
| पिन 6 | SD0 — Downstream channel 0 data (bidirectional pass gate) |
| पिन 7 | SC1 — Downstream channel 1 clock (bidirectional pass gate) |
| पिन 8 | SD1 — Downstream channel 1 data (bidirectional pass gate) |
| पिन 9 | SC2 — Downstream channel 2 clock (bidirectional pass gate) |
| पिन 10 | SD2 — Downstream channel 2 data (bidirectional pass gate) |
| पिन 11 | SC3 — Downstream channel 3 clock (bidirectional pass gate) |
| पिन 12 | SD3 — Downstream channel 3 data (bidirectional pass gate) |
| पिन 13 | GND — Ground |
| पिन 14 | VDD — Positive supply; also limits the maximum high voltage passed through the channels |
| पिन 15 | A0 — Address input bit 0 |
| पिन 16 | A1 — Address input bit 1 |
सामान्य अनुप्रयोग
PCA9546ADW के लिए उपयुक्त है 6 अनुप्रयोगs: Multi-Sensor Measurement Hub, Serial EEPROM and Flash Bank Fan-Out, LED Driver Array Control, Real-Time Clock and PMIC Management, Industrial Data Acquisition, Test and Measurement Fixture.
Multi-Sensor Measurement Hub
The PCA9546ADW lets one microcontroller reach four separate sensor segments over a single upstream SCL/SDA pair, which keeps the host PCB from needing a separate bus header for every sensor. Each downstream SCn/SDn pair can be selected independently, so a firmware scan cycle can enable one segment at a time, read it, and move on, reducing bus capacitance on the active segment and simplifying address planning across four unrelated sensor families. Because the pass gates are bidirectional, the same topology also works when a sensor must drive data back toward the controller. The RESET input gives the hub a clean recovery path if a target holds SDA low after a brown-out, and the internal power-on reset guarantees that no channel is left enabled at startup.
अनुशंसित
Serial EEPROM and Flash Bank Fan-Out
Banks of serial memories frequently exceed the address budget of one I2C segment, and adding a second microcontroller pin pair for every memory is expensive in routing and board area. The PCA9546ADW resolves this by placing up to four memory banks behind one upstream pair, with each bank enabled by a bit in the control register. Memory buses are strongly pull-up dominated, so the per-segment pull-up arrangement recommended for the PCA9546ADW keeps each bank at its intended rise time rather than sharing a single weak pull-up network with unused stubs. The two address pins also make it practical to combine several switches on one bus when the design needs more than four banks.
अनुशंसित
LED Driver Array Control
Addressable LED drivers such as the PCA9956 family and similar constant-current drivers commonly share a single command bus, and an LED panel with several driver rows or zones is a natural fit for channel multiplexing. The PCA9546ADW routes the upstream command and data lines to one driver row at a time, which keeps the total device count on the shared bus low and prevents commands intended for one row from appearing on another. Since LED drivers often latch a command and then shift data internally, the bidirectional pass gates of the PCA9546ADW handle both the write and acknowledge phases. Panel designs also benefit from tying RESET to the panel reset line so a newly powered driver group is addressed cleanly.
अनुशंसित
Real-Time Clock and PMIC Management
Compact embedded systems often pair a real-time clock, a power management device, and a fuel gauge that all respond to the same I2C address ranges or sit behind separate connectors on different boards. The PCA9546ADW isolates those devices onto discrete downstream segments, so the host processor can address each device unambiguously while still using one bus header to the module. Isolation also stops an unpowered sub-board from back-powering the main rail through the shared lines, which is a common source of brown-out and partial-power failures. The active-low RESET input is useful here as well, because it re-initializes the mux state machine whenever the module is power-cycled.
अनुशंसित
Industrial Data Acquisition
Industrial acquisition cards often terminate several remote sensor strings on one board, and each string can sit at a different ground potential or carry its own local controller. The PCA9546ADW lets the card present one upstream SCL/SDA pair to the backplane while routing it to as many as four locally terminated downstream channels. Because the pass-gate structure allows the VDD pin to limit the maximum high voltage that is passed, the switch can be used to add a level of protection to the forwarded bus in designs where the downstream segment is exposed to harsher conditions. The RESET pin doubles as a bus-recovery mechanism when a field-wired target locks up SDA after surge events.
अनुशंसित
Test and Measurement Fixture
Automated test fixtures frequently need to reach several DUT straps, buffer amplifiers, or EEPROMs that do not share a common address map, and the fixture controller typically exposes only one I2C header. The PCA9546ADW converts that single header into four independently addressable DUT ports, so the test sequence can select one device at a time and avoid address collisions between instruments and the DUT. The ability to deselect all channels through RESET also helps the fixture establish a known state between test iterations, which shortens measurement setup time and improves repeatability. Because the fixture is a small, adapter-board design, the 16-pin SOIC footprint keeps the adapter routing simple and manufacturable.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा PCA9546ADW — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | TCA9546ADWR | PCA9546AD |
|---|---|---|---|
| Package | SOIC-16 (DW) | SOIC-16 (DW) - same | SOIC-16 (D) - narrower body, verify pad span |
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Number of Channels | 4 downstream SCn/SDn channels | 4 downstream SCn/SDn channels | 4 downstream SCn/SDn channels |
| Upstream Port | 1 (SCL/SDA) | 1 (SCL/SDA) | 1 (SCL/SDA) |
| Bus Support | I2C and SMBus | I2C and SMBus | I2C and SMBus |
| Signal Direction | Bidirectional pass gates | Bidirectional pass gates | Bidirectional pass gates |
| Reset Function | Active-low RESET plus internal power-on reset | Active-low RESET plus internal power-on reset | Active-low RESET plus internal power-on reset |
| VDD High-Voltage Limiting of Pass Gates | Supported - VDD pin limits the maximum high voltage passed | Supported - VDD pin limits the maximum high voltage passed | Supported - VDD pin limits the maximum high voltage passed |
| Address Pins | 2 (A0/A1) | 2 (A0/A1) | 2 (A0/A1) |
मुख्य विशेषताएँ
- Reset input plus internal power-on reset gives a defined mux state and a bus-recovery path (बनामPCA9546AD (NXP))
- Same-family naming consistency with the wider 16-pin SOIC (DW) outline (बनामPCA9546AD (NXP))
- Four independently selectable channels with two address pins for multi-switch systems (बनामTCA9546ADWR)
डिज़ाइन नोट्स
Route the upstream SCL and SDA pair as a short, tightly coupled pair from the controller to pins 3 and 4, and keep each downstream SCn/SDn pair matched in length to its own channel. Do not run downstream stubs past the switch into channels you do not use, because an open stub on a pass-gate segment raises the effective capacitance seen by the upstream driver and slows the rising edge. Where a channel is unused, leave the pins unconnected rather than routing them to a test pad that dangles.
Decouple the VDD pin close to the device with a local ceramic capacitor and return the ground pins (2 and 13) directly to the ground plane rather than through a shared trace. Remember that on this class of device the VDD pin also sets the maximum high voltage that the pass gates will forward, so the supply choice and the bus voltage level of the downstream segment must be consistent. Do not use a VDD value that is lower than the logic high level of the downstream devices you intend to switch to.
The most common integration error is a single shared pull-up network across all four downstream segments. Place pull-ups on the upstream side for the controller bus and a separate pull-up pair on each enabled downstream segment, sized for that segment's capacitance. A second common mistake is ignoring the RESET line: connect it to the system reset so that a brown-out on the downstream rail cannot leave the multiplexer addressing a segment that is no longer powered.
Treat the four downstream segments as four separate buses, not as one large bus, and keep each segment's device population as small as practical so that rise times stay within the limits specified for the controller. When the system must tolerate a downstream fault, remember that RESET de-selects all channels and clears the internal state machine, which releases a segment whose target has latched SDA low; use this as the documented recovery step in the system fault handler rather than power-cycling the whole board.
अनुपालन जानकारी
The interface switch is not an automotive-qualified device, so AEC-Q100 does not apply. RoHS, REACH, lead-free and halogen-free statements were not stated in the manufacturer material captured for this part; confirm the current declarations on the manufacturer product page before release.