Texas Instruments

PCM1770RGAR - 24-Bit Stereo DAC with HP Amp, 98dB SNR | Texas Instruments

MPN: PCM1770RGAR ✓ सक्रिय
Single supply Vdss VQFN-20 (RGA) 4.2 x 4.2 mm, HVQCCN Package
न्यूनतम ऑर्डर मात्रा: 1 |

PCM1770RGAR अवलोकन

The Texas Instruments PCM1770RGAR is a 24-bit stereo audio digital-to-analog converter with an integrated headphone amplifier and software-controlled output switching, delivering 98 dB SNR at up to 48 kHz sampling in a 20-pin VQFN (RGA) 4.2 x 4.2 mm package.

An audio DAC is a signal-chain integrated circuit that converts digital audio samples into an analog voltage; a DAC with an integrated headphone amplifier adds a low-noise current/voltage output stage so that headphones can be driven directly without a separate amplifier chip. In the component hierarchy the PCM1770RGAR sits as an audio codec-class converter: stereo DAC -> audio converter IC -> signal-chain semiconductor, one tier above discrete op-amp output stages and one tier below a full audio codec with analog inputs.

Key features include 24-bit resolution, 98 dB signal-to-noise ratio, a 2-channel architecture with no analog input paths, an SPI control port for register-based configuration, and single-supply operation from 1.6 V for low-voltage portable systems. The headphone output stage is controlled in software, allowing mute and channel-routing functions to be driven from the host microcontroller rather than external hardware.

Internally the device is a CMOS monolithic converter built on TI's enhanced multilevel architecture, employing noise shaping and multilevel amplitude quantization to push quantization noise out of the audio band while keeping the required passband filter simple. The 20-pin VQFN (RGA) package is a leadless HVQCCN outline with a thermal and ground pad, which lowers parasitic inductance on digital lines and keeps the footprint smaller than the 16-pin TSSOP alternative offered in the same family.

Typical uses include USB and Bluetooth audio dongles, portable media players and handsets with analog headphone output, digital mixing consoles and broadcast monitors that need a low-noise local DAC, and instrumentation or test equipment that generates analog audio from a digital source. In each case the part replaces a discrete DAC plus output buffer and reduces both board area and assembly count.

When laying out the PCB, place the analog and digital supplies' decoupling capacitors directly at the package pins, bond the exposed pad to a solid ground plane, and keep the SPI clock and data traces short and referenced to a quiet ground region. Master clock jitter and the ratio between master clock and the audio sample rate determine the achievable dynamic range, so a clean, low-jitter clock source is as important as the filter selection.

This page consolidates the device specifications, a package-matched drop-in alternative list, a parameter-by-parameter comparison and practical layout notes into one engineering-focused reference that the manufacturer datasheet alone does not provide.

के लिए ड्रॉप-इन विकल्प PCM1770RGAR — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं PCM1770RGAR (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Maximum Sampling Rate, Signal-to-Noise Ratio, Architecture, Operating Temperature Range.

Texas Instruments
Package: 20-pin VQFNP (RGA)
Maximum Sampling Rate: 50 kHz
Signal-to-Noise Ratio: 98 dB
इसके साथ तुलना करें PCM1770RGAR →
Texas Instruments
Package: 20-pin VQFN (RGA), 4.2 mm × 4.2 mm
Maximum Sampling Rate: 50 kHz
Signal-to-Noise Ratio: 98 dB
इसके साथ तुलना करें PCM1770RGAR →

PCM1771RGAR

✅ ड्रॉप-इन
📦 VQFN-20 (RGA) 4.2 x 4.2 mm
same 24-bit stereo converter core, same 20-pin VQFN outline and 48 kHz class sampling; control register set and feature emphasis differ, so firmware register writes are not interchangeable

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

PCM1772RGAR

✅ ड्रॉप-इन
📦 VQFN-20 (RGA) 4.2 x 4.2 mm
same 24-bit low-power stereo DAC in the identical 20-pin VQFN package, but no integrated headphone amplifier stage, so an external output amplifier is required (+0 dB versus integrated HP output)

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

PCM1773RGAR

✅ ड्रॉप-इन
📦 VQFN-20 (RGA) 4.2 x 4.2 mm
same 20-pin VQFN stereo DAC footprint and 24-bit/48 kHz class conversion core; published SNR figure for this variant is not stated in the retrieved listings, so noise performance may differ from the 98 dB of the PCM1770

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

PCM1770RGA

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 VQFN-20 (RGA) 4.2 x 4.2 mm
identical device, identical electrical specifications and identical 20-pin VQFN land pattern; differs only in shipping format (tray rather than tape and reel)

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

PCM1770RGAG4

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 VQFN-20 (RGA) 4.2 x 4.2 mm
identical die and 20-pin VQFN footprint with 100% of the 24-bit/48 kHz/98 dB key ratings; differs only in the lead-free green (G4) environmental ordering code

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

PCM1770RGAR Maximum Ratings और Electrical Characteristics

रेज़ोल्यूशन 24 bit
DAC Channels 2 (stereo)
Maximum Sampling Rate 48 kHz
Signal-to-Noise Ratio 98 dB (typical)
Architecture Multilevel delta-sigma (noise shaping with multilevel amplitude quantization)
Control Interface SPI
Supply Type Single supply
Minimum Supply Voltage 1.6 V
Integrated Headphone Amplifier Yes, with software (S/W) control
पैकेज VQFN-20 (RGA) 4.2 x 4.2 mm, HVQCCN
Number of Terminals 20
Terminal Form No lead
Package Shape Square
माउंटिंग प्रकार Surface mount
Temperature Grade Commercial
RoHS स्थिति Compliant (RoHS3 per distributor listing)

PCM1770RGAR square पिन कॉन्फ़िगरेशन गाइड

PCM1770RGAR (square पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

PCM1770RGAR के लिए square पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: PCM1770RGAR.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

PCM1770RGAR के लिए उपयुक्त है 6 अनुप्रयोगs: USB Audio DAC Dongle with Headphone Output, Portable Media Player and Handset Headphone Drive, Digital Mixer Console and Broadcast Monitoring, Instrumentation and Test Audio Source, Automotive Infotainment and Telematics Audio, Bluetooth and Network Audio Receiver Module.

🎧

USB Audio DAC Dongle with Headphone Output

The PCM1770RGAR suits a USB audio dongle that converts 24-bit playback streams into analog line and headphone signals. Its 24-bit resolution preserves the full dynamic range of 24-bit host files, the 98 dB SNR keeps the noise floor well below headphone audibility, and the integrated software-controlled headphone amplifier removes the need for a separate output buffer chip. With single-supply operation from 1.6 V, the converter works directly from a 3.3 V or 5 V USB-derived rail. In this design the converter sits behind the USB controller, clocked by a low-jitter master clock derived from the host, with the analog outputs driven through a passive coupling network and the headphone outputs taken directly from the integrated amplifier.

📱

Portable Media Player and Handset Headphone Drive

In a portable media player or handset, board area and power budget both matter, and the PCM1770RGAR addresses both. The 20-pin VQFN (RGA) package occupies only 4.2 x 4.2 mm, so it fits beside a processor and flash on a dense main board, while single-supply operation from 1.6 V allows operation directly from a low cell voltage. The integrated headphone amplifier with software control lets the host codec mute or reconfigure the output path in firmware rather than through external switching hardware. Trade-off to note: the headphone stage adds power draw versus a line-output-only converter, so duty-cycled headphone enable in software is worthwhile in battery designs.

🏭

Digital Mixer Console and Broadcast Monitoring

A digital mixing console or broadcast monitor often needs a local high-quality analog output for cue speakers, and the PCM1770RGAR provides that conversion stage. The 24-bit resolution and 98 dB SNR give more headroom than typical 16-bit paths, which reduces quantizing distortion when several mix buses are summed digitally and reproduced on a single stereo monitor pair. Because the converter accepts no analog input, it drops cleanly into a digital signal chain, and the SPI control port allows the console firmware to set mute state and output routing without mechanical relays. Watch the master clock: in a multi-channel console the clock distribution network, not the converter, is usually the limiting factor for the final dynamic range.

🔧

Instrumentation and Test Audio Source

In test and measurement equipment that must produce a known analog audio output, the PCM1770RGAR offers a compact, reproducible 24-bit source. Digital stimulus data can be generated by the instrument's processor and converted to analog with the 98 dB SNR of the converter, while the software-controlled headphone and line switching allows the same board to serve headphone monitoring and balanced line output. Because the part is a low-power CMOS converter in a small leadless package, it also fits bench instruments where panel space is limited. Keep analog output traces short and away from the SPI bus to avoid coupling control activity into the measured output.

🚗

Automotive Infotainment and Telematics Audio

An automotive infotainment head unit or telematics control unit needs a reliable local audio path, and the PCM1770RGAR suits designs that stay within the 24-bit, 48 kHz class audio typical of in-vehicle systems. The single-supply operation simplifies power tree design, and the VQFN-20 leadless footprint is compatible with automated assembly and with boards that must survive vibration and thermal cycling. The integrated headphone amplifier is useful for driver-seat personal audio outputs, and the software switching lets the head unit mute or reroute channels on state changes. For safety-critical deployments, confirm the AEC-Q100 qualification status of the specific ordering code with the manufacturer before releasing it into a vehicle program.

🌐

Bluetooth and Network Audio Receiver Module

A Bluetooth or network audio receiver that terminates in analog line output can use the PCM1770RGAR as the final conversion stage. The SPI control port lets the module's host processor configure format, mute and output switching as soon as a stream is established, which keeps the analog path quiet during idle periods. Its 4.2 x 4.2 mm footprint allows placement close to the antenna-side RF and baseband section, shortening the sensitive analog traces and reducing radiated emissions from digital coupling. The trade-off to plan for is clocking: network audio arrives with its own timing, so the master clock source and the ratio to the sample rate determine whether the full 98 dB SNR is realized.

What is the PCM1770RGAR?
The PCM1770RGAR is a Texas Instruments 24-bit stereo digital-to-analog converter with an integrated headphone amplifier and software-controlled switching. It converts two channels of digital audio into analog output, offers 98 dB SNR, and is controlled through an SPI port. The device is packaged in a 20-pin VQFN (RGA) 4.2 x 4.2 mm leadless package, and operates from a single supply with a 1.6 V minimum input.
What are the key specifications of PCM1770RGAR that engineers should know?
The PCM1770RGAR is a 2-channel, 24-bit DAC with 98 dB SNR, a maximum sampling rate of 48 kHz, a multilevel delta-sigma architecture with noise shaping, SPI control, and an integrated software-controlled headphone amplifier. It uses a single supply with a 1.6 V minimum, has no analog input paths, and comes in the 20-pin VQFN (RGA) package with an exposed thermal and ground pad. The TI part description lists the device as a 98 dB SNR low-power stereo DAC with headphone amplifier.
What is the output SNR of PCM1770RGAR?
The PCM1770RGAR delivers 98 dB typical signal-to-noise ratio as stated in the TI product description for the PCM1770 family. This figure is measured against the digital input with the analog output referenced to full scale, so actual in-system performance also depends on supply noise and the layout of the reference and output network.
What sampling rates does the PCM1770RGAR support?
The PCM1770RGAR supports sampling rates up to 48 kHz according to the published family comparison data, and distributor catalogs classify the part in the 50 kHz class for 24-bit audio. It is therefore intended for CD-quality standard-rate audio and consumer multimedia rather than 96 kHz or 192 kHz high-resolution streams. Verify the master-clock ratio requirement in the datasheet for the system mode you plan to use.
What control interface does the PCM1770RGAR use?
The PCM1770RGAR is configured through an SPI serial control port. Register writes set the audio data format, mute state, the software-controlled headphone output switching and the operating mode, while audio samples themselves are clocked in by the audio interface in parallel with control traffic. SPI keeps the control pin count low, which matters in the small 4.2 x 4.2 mm footprint.
What supply voltage does PCM1770RGAR need?
The PCM1770RGAR runs from a single supply with a minimum input voltage of 1.6 V, which supports low-voltage portable and battery-powered designs. It separates analog and digital supply pins, so each rail should be decoupled locally with its own capacitor group and referenced to the same ground plane.
Where to download the PCM1770RGAR datasheet PDF?
The PCM1770RGAR datasheet is published by Texas Instruments and can be reached from the TI PCM1770 product page or through the TI literature link at https://www.ti.com/lit/ds/symlink/pcm1770.pdf. The document contains the pin configuration, the recommended operating conditions, the typical application circuit, the digital audio interface timing and the control register map. Mirror copies of the same document are also indexed by third-party datasheet aggregators.
Where can I find the PCM1770RGAR pinout?
The complete 20-pin VQFN (RGA) pin assignment is tabulated in the pin configuration section of the Texas Instruments PCM1770 datasheet, together with the exposed pad connection. Use that table when assigning PCB nets, because the analog supply, digital supply, grounds, master clock, serial data and SPI control lines are interleaved on the fine-pitch 4.2 mm square outline. A package diagram with all 20 positions is shown on this page alongside the source document.
PCM1770RGAR vs PCM1772RGAR - which is better for a headphone output design?
Choose the PCM1770RGAR when the design needs an integrated headphone amplifier with software-controlled switching, because the TI part description specifies a headphone amplifier with S/W control in a 20-pin VQFN package. The PCM1772RGAR is also a 24-bit low-power stereo DAC in a 20-pin VQFN, but its role is line-level conversion, so a discrete or integrated output amplifier must be added. The trade-off is board area: the PCM1770RGAR saves an amplifier stage, the PCM1772RGAR offers a leaner analog path.
Is the PCM1770RGAR suitable for a USB audio dongle?
Yes, the PCM1770RGAR fits a USB audio dongle that outputs analog audio to headphones or line inputs. Its single-supply operation down to 1.6 V suits USB-powered 5 V or 3.3 V rails, the 24-bit resolution suits 16-bit/24-bit playback, and the integrated headphone amplifier removes the need for a separate output buffer. Provide a low-jitter master clock, as USB audio source implementations typically derive their clock from the host and the converter's dynamic range depends on clock quality.
When should I choose PCM1770RGAR over PCM1771RGAR?
Choose the PCM1770RGAR when your design relies on the software-controlled headphone output behavior and you have already validated its control register map against your firmware. The PCM1771RGAR is a sibling device in the same 24-bit stereo converter family and shares the 20-pin VQFN outline, but its register set and feature mix differ, so it is not a firmware-transparent substitution. In both cases confirm the audio data format, mute behavior and mode pins against the datasheet before committing the layout.
What is the best drop-in replacement for PCM1770RGAR?
The best drop-in replacements are the same-family Texas Instruments 20-pin VQFN parts listed on this page, such as PCM1771RGAR, PCM1772RGAR and PCM1773RGAR, which use the identical 4.2 x 4.2 mm HVQCCN footprint and the same 24-bit stereo converter core. Because the control register map differs between family members, verify mode pin settings and register writes in the datasheet before substituting. A like-for-like swap that keeps the exact same device with different reel packing is also available as PCM1770RGA.
What can replace the PCM1770RGAR?
Drop-in replacements for the PCM1770RGAR must keep the 20-pin VQFN (RGA) footprint, 24-bit resolution, 2-channel output and single-supply operation, because changing the package forces a PCB respin. Members of the PCM177x family in the same VQFN-20 outline satisfy the mechanical and electrical fit; register compatibility must still be confirmed line by line against the datasheet. If a footprint change is acceptable, the 16-pin TSSOP variant of the family offers a smaller pin count at the cost of a different land pattern.
Is the PCM1770RGAR the same as the PCM1771RGAR?
No. The PCM1770RGAR and PCM1771RGAR are related but distinct members of the Texas Instruments 24-bit stereo converter family, and both are offered in a 20-pin VQFN (RGA) package. They differ in feature emphasis and control behavior, so the pin-compatible footprint does not imply identical functionality. Treat them as alternative candidates for a layout, not as interchangeable parts for an existing firmware.
Where can I buy PCM1770RGAR online?
You can request a quote for the PCM1770RGAR through the Request a Quote form on this page, where XAIPART confirms availability, condition and delivery options for the 20-pin VQFN (RGA) package. The same applies for volume quantities and scheduled deliveries, which are easier to commit through a quote than through a static listing. Use the form for a current answer rather than relying on cached distributor pages.
What is the price of PCM1770RGAR?
Pricing for the PCM1770RGAR is generated live for your quantity and delivery terms through the Request a Quote form on this page, so no static figure should be treated as current. Stock on this legacy audio converter moves in small quantities across authorized channels, so a quote reflects the real position rather than an outdated catalog entry. Ask for the 3000-piece tape-and-reel quantity as well as single-unit quantities when planning production.
What is the lead time for PCM1770RGAR?
Current lead time and minimum order quantity for the PCM1770RGAR are confirmed through the Request a Quote form on this page, which lets you state the target quantity, reel size and required delivery date. Because this part has been in the catalog for many years, factory support and standard packaging quantities are stable, but allocation can vary with demand. Provide your schedule early so a date can be committed against a production build.
Is PCM1770RGAR in stock?
Live inventory for the PCM1770RGAR is confirmed through the Request a Quote form on this page, where the answer reflects the current position for the exact VQFN (RGA) ordering code you intend to use. Because the same device is offered in several packing codes, check availability for the code that matches your assembly process, whether tray, tape and reel or cut tape. Requesting a quote for the exact quantity you need is the fastest way to confirm both stock and delivery.

के लिए इंजीनियरिंग संदर्भ डेटा PCM1770RGAR — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the PCM1770RGAR when your design needs a compact 24-bit stereo DAC that can drive headphones directly and be muted or reconfigured from firmware, particularly in USB dongles, portable players and instrument audio sources where the 4.2 x 4.2 mm footprint and 1.6 V single-supply operation matter. Choose the PCM1772RGAR when you want a line-level stereo DAC in the same 20-pin VQFN footprint and prefer to control the output amplifier yourself; you accept the extra amplifier stage in exchange for a simpler analog path. Choose the PCM1771RGAR when its specific feature mix matches your system better, but confirm the control register map in the datasheet before reusing existing firmware. For a like-for-like manufacturing change, the PCM1770RGA tray ordering code is electrically identical. If your product needs a single board that must also accept analog sources, this converter has no analog inputs and a codec-class device is the better architectural choice.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद PCM1771RGAR PCM1772RGAR PCM1773RGAR PCM1770RGA
Package VQFN-20 (RGA) 4.2 x 4.2 mm VQFN-20 (RGA) 4.2 x 4.2 mm - same VQFN-20 (RGA) 4.2 x 4.2 mm - same VQFN-20 (RGA) 4.2 x 4.2 mm - same VQFN-20 (RGA) 4.2 x 4.2 mm - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
DAC Channels 2 (stereo) 2 2 (stereo) 2 (stereo) 2 (stereo)
Number of Terminals 20 20 20 20 20

मुख्य विशेषताएँ

  • Integrated headphone amplifier with software control removes a discrete output stage (बनामPCM1772RGAR)
  • Same 24-bit converter core and package as PCM1771RGAR, but a distinct, documented control set (बनामPCM1771RGAR)
  • Drop-in flexibility within the same land pattern through identical-device ordering codes (बनामPCM1770RGA)

डिज़ाइन नोट्स

The 20-pin VQFN (RGA) land pattern is only 4.2 x 4.2 mm with fine-pitch leads, so pad geometry and solder mask definition matter as much as routing. Follow the land pattern in the TI datasheet exactly, including the exposed thermal pad and its solder mask opening, and check that your assembly house supports a 0.5 mm pitch fine-pitch package with a bottom paste stencil. Keep the analog supply (AVDD), digital supply (DVDD) and their decoupling capacitors adjacent to the corresponding pins so that loop area stays minimal.

Bond the exposed pad to a low-impedance ground plane with a full set of thermal vias placed directly under the pad, because the pad is both the thermal path and the device ground reference. Route SPI clock, data and mode pins on the digital side of the board and keep analog output nets away from them, since coupling from the SPI bus into the headphone and line outputs is a common source of audible clicks and hiss. A clean split between analog and digital ground regions, joined at a single point near the converter, usually preserves more of the 98 dB SNR than a fully interleaved plane.

The achievable dynamic range of this converter depends on master clock quality as much as on the internal converter. Use a low-jitter oscillator or a jitter-cleaned clock, feed the master clock into the package on a short trace with a controlled impedance, and confirm the required master-clock-to-sample-rate ratio for the operating mode in the datasheet. Audio data and latch clock lines should be length-matched and routed away from switching nodes, and the SPI bus should be kept short or series-terminated if the board is large.

Two mistakes dominate in designs built around this converter. First, treating the SPI mode and format pins as decorative: they must be strapped for the interface mode and data format your firmware expects, and a wrong strap produces scrambled audio even though the clocking looks correct. Second, expecting analog input paths - the device has none, so any source signal must arrive digitally. Also verify the headphone mute and switching behavior in firmware before taping out, and keep the audio interface idle until the master clock is stable.

Estimated power use: with a 3.3 V analog and digital supply, a 48 kHz stereo stream and the headphone stage enabled, the converter typically draws only a few tens of milliwatts, but the integrated headphone amplifier adds current that scales with output power into the load. Estimate the headphone dissipation as Vrms squared divided by the headphone impedance, add the converter static current times the supply voltage, and confirm that the supply can deliver the peak current on headphone load transients. Place a bulk capacitor near the headphone supply rail to absorb those transients.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

A distributor product listing marks the PCM1770RGAR as RoHS3 compliant. No REACH, AEC-Q100, lead-free or halogen-free statements are published for this ordering code in the available listings, so those fields remain unconfirmed; the green (G4) ordering code indicates the lead-free-compliant variant of the same device.

डेटा सत्यापन तिथि: 2026-11-20 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

PCM1770RGAR PCM1770RGAR datasheet PCM1770RGAR datasheet pdf PCM1770RGAR pinout PCM1770RGAR VQFN-20 footprint PCM1770RGAR price PCM1770RGAR stock PCM1770RGAR equivalent PCM1770RGAR replacement PCM1770RGAR vs PCM1772RGAR Texas Instruments PCM1770 PCM1770 24 bit stereo DAC headphone amplifier PCM1770RGAR application circuit PCM1770RGAR USB audio DAC

संबंधित कंपोनेंट्स और शब्द

Texas Instruments PCM1770 PCM1770RGAR PCM1771RGAR PCM1772RGAR PCM1773RGAR PCM1770RGA PCM1770RGAG4 PCM1681PWPR PCM3060PWR PCM3010DBR PCM5142PWR digital-to-analog converter DAC stereo DAC audio codec headphone amplifier multilevel delta-sigma noise shaping multilevel amplitude quantization signal-to-noise ratio SPI control interface I2S master clock VQFN-20 RGA package HVQCCN QFN package family surface mount SMD single supply RoHS 98 dB SNR 48 kHz sampling USB audio portable audio
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें