PCM1770RGAR - 24-Bit Stereo DAC with HP Amp, 98dB SNR | Texas Instruments
料号: PCM1770RGAR ✓ 量产中PCM1770RGAR 概述
An audio DAC is a signal-chain integrated circuit that converts digital audio samples into an analog voltage; a DAC with an integrated headphone amplifier adds a low-noise current/voltage output stage so that headphones can be driven directly without a separate amplifier chip. In the component hierarchy the PCM1770RGAR sits as an audio codec-class converter: stereo DAC -> audio converter IC -> signal-chain semiconductor, one tier above discrete op-amp output stages and one tier below a full audio codec with analog inputs.
Key features include 24-bit resolution, 98 dB signal-to-noise ratio, a 2-channel architecture with no analog input paths, an SPI control port for register-based configuration, and single-supply operation from 1.6 V for low-voltage portable systems. The headphone output stage is controlled in software, allowing mute and channel-routing functions to be driven from the host microcontroller rather than external hardware.
Internally the device is a CMOS monolithic converter built on TI's enhanced multilevel architecture, employing noise shaping and multilevel amplitude quantization to push quantization noise out of the audio band while keeping the required passband filter simple. The 20-pin VQFN (RGA) package is a leadless HVQCCN outline with a thermal and ground pad, which lowers parasitic inductance on digital lines and keeps the footprint smaller than the 16-pin TSSOP alternative offered in the same family.
Typical uses include USB and Bluetooth audio dongles, portable media players and handsets with analog headphone output, digital mixing consoles and broadcast monitors that need a low-noise local DAC, and instrumentation or test equipment that generates analog audio from a digital source. In each case the part replaces a discrete DAC plus output buffer and reduces both board area and assembly count.
When laying out the PCB, place the analog and digital supplies' decoupling capacitors directly at the package pins, bond the exposed pad to a solid ground plane, and keep the SPI clock and data traces short and referenced to a quiet ground region. Master clock jitter and the ratio between master clock and the audio sample rate determine the achievable dynamic range, so a clean, low-jitter clock source is as important as the filter selection.
This page consolidates the device specifications, a package-matched drop-in alternative list, a parameter-by-parameter comparison and practical layout notes into one engineering-focused reference that the manufacturer datasheet alone does not provide.
直接替换替代料: PCM1770RGAR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCM1770RGAR (相同外形与封装尺寸) ——差异在于 Package, Maximum Sampling Rate, Signal-to-Noise Ratio, Architecture, Operating Temperature Range.
PCM1771RGAR
✅ 直接替换📋 参考替代料(不在目录中)
PCM1772RGAR
✅ 直接替换📋 参考替代料(不在目录中)
PCM1773RGAR
✅ 直接替换📋 参考替代料(不在目录中)
PCM1770RGA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1770RGAG4
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCM1770RGAR 最大额定值与电气特性
| 分辨率 | 24 bit |
| DAC Channels | 2 (stereo) |
| Maximum Sampling Rate | 48 kHz |
| Signal-to-Noise Ratio | 98 dB (typical) |
| Architecture | Multilevel delta-sigma (noise shaping with multilevel amplitude quantization) |
| Control Interface | SPI |
| Supply Type | Single supply |
| Minimum Supply Voltage | 1.6 V |
| Integrated Headphone Amplifier | Yes, with software (S/W) control |
| 封装 | VQFN-20 (RGA) 4.2 x 4.2 mm, HVQCCN |
| Number of Terminals | 20 |
| Terminal Form | No lead |
| Package Shape | Square |
| 安装类型 | Surface mount |
| Temperature Grade | Commercial |
| RoHS 状态 | Compliant (RoHS3 per distributor listing) |
PCM1770RGAR square 引脚配置指南
PCM1770RGAR(square 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: PCM1770RGAR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCM1770RGAR 适用于 6 应用s: USB Audio DAC Dongle with Headphone Output, Portable Media Player and Handset Headphone Drive, Digital Mixer Console and Broadcast Monitoring, Instrumentation and Test Audio Source, Automotive Infotainment and Telematics Audio, Bluetooth and Network Audio Receiver Module.
USB Audio DAC Dongle with Headphone Output
The PCM1770RGAR suits a USB audio dongle that converts 24-bit playback streams into analog line and headphone signals. Its 24-bit resolution preserves the full dynamic range of 24-bit host files, the 98 dB SNR keeps the noise floor well below headphone audibility, and the integrated software-controlled headphone amplifier removes the need for a separate output buffer chip. With single-supply operation from 1.6 V, the converter works directly from a 3.3 V or 5 V USB-derived rail. In this design the converter sits behind the USB controller, clocked by a low-jitter master clock derived from the host, with the analog outputs driven through a passive coupling network and the headphone outputs taken directly from the integrated amplifier.
推荐
Portable Media Player and Handset Headphone Drive
In a portable media player or handset, board area and power budget both matter, and the PCM1770RGAR addresses both. The 20-pin VQFN (RGA) package occupies only 4.2 x 4.2 mm, so it fits beside a processor and flash on a dense main board, while single-supply operation from 1.6 V allows operation directly from a low cell voltage. The integrated headphone amplifier with software control lets the host codec mute or reconfigure the output path in firmware rather than through external switching hardware. Trade-off to note: the headphone stage adds power draw versus a line-output-only converter, so duty-cycled headphone enable in software is worthwhile in battery designs.
推荐
Digital Mixer Console and Broadcast Monitoring
A digital mixing console or broadcast monitor often needs a local high-quality analog output for cue speakers, and the PCM1770RGAR provides that conversion stage. The 24-bit resolution and 98 dB SNR give more headroom than typical 16-bit paths, which reduces quantizing distortion when several mix buses are summed digitally and reproduced on a single stereo monitor pair. Because the converter accepts no analog input, it drops cleanly into a digital signal chain, and the SPI control port allows the console firmware to set mute state and output routing without mechanical relays. Watch the master clock: in a multi-channel console the clock distribution network, not the converter, is usually the limiting factor for the final dynamic range.
推荐
Instrumentation and Test Audio Source
In test and measurement equipment that must produce a known analog audio output, the PCM1770RGAR offers a compact, reproducible 24-bit source. Digital stimulus data can be generated by the instrument's processor and converted to analog with the 98 dB SNR of the converter, while the software-controlled headphone and line switching allows the same board to serve headphone monitoring and balanced line output. Because the part is a low-power CMOS converter in a small leadless package, it also fits bench instruments where panel space is limited. Keep analog output traces short and away from the SPI bus to avoid coupling control activity into the measured output.
推荐
Automotive Infotainment and Telematics Audio
An automotive infotainment head unit or telematics control unit needs a reliable local audio path, and the PCM1770RGAR suits designs that stay within the 24-bit, 48 kHz class audio typical of in-vehicle systems. The single-supply operation simplifies power tree design, and the VQFN-20 leadless footprint is compatible with automated assembly and with boards that must survive vibration and thermal cycling. The integrated headphone amplifier is useful for driver-seat personal audio outputs, and the software switching lets the head unit mute or reroute channels on state changes. For safety-critical deployments, confirm the AEC-Q100 qualification status of the specific ordering code with the manufacturer before releasing it into a vehicle program.
推荐
Bluetooth and Network Audio Receiver Module
A Bluetooth or network audio receiver that terminates in analog line output can use the PCM1770RGAR as the final conversion stage. The SPI control port lets the module's host processor configure format, mute and output switching as soon as a stream is established, which keeps the analog path quiet during idle periods. Its 4.2 x 4.2 mm footprint allows placement close to the antenna-side RF and baseband section, shortening the sensitive analog traces and reducing radiated emissions from digital coupling. The trade-off to plan for is clocking: network audio arrives with its own timing, so the master clock source and the ratio to the sample rate determine whether the full 98 dB SNR is realized.
推荐
推荐产品汇总
工程参考数据: PCM1770RGAR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCM1771RGAR | PCM1772RGAR | PCM1773RGAR | PCM1770RGA |
|---|---|---|---|---|---|
| Package | VQFN-20 (RGA) 4.2 x 4.2 mm | VQFN-20 (RGA) 4.2 x 4.2 mm - same | VQFN-20 (RGA) 4.2 x 4.2 mm - same | VQFN-20 (RGA) 4.2 x 4.2 mm - same | VQFN-20 (RGA) 4.2 x 4.2 mm - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| DAC Channels | 2 (stereo) | 2 | 2 (stereo) | 2 (stereo) | 2 (stereo) |
| Number of Terminals | 20 | 20 | 20 | 20 | 20 |
关键差异点
- Integrated headphone amplifier with software control removes a discrete output stage (对比 PCM1772RGAR)
- Same 24-bit converter core and package as PCM1771RGAR, but a distinct, documented control set (对比 PCM1771RGAR)
- Drop-in flexibility within the same land pattern through identical-device ordering codes (对比 PCM1770RGA)
设计说明
The 20-pin VQFN (RGA) land pattern is only 4.2 x 4.2 mm with fine-pitch leads, so pad geometry and solder mask definition matter as much as routing. Follow the land pattern in the TI datasheet exactly, including the exposed thermal pad and its solder mask opening, and check that your assembly house supports a 0.5 mm pitch fine-pitch package with a bottom paste stencil. Keep the analog supply (AVDD), digital supply (DVDD) and their decoupling capacitors adjacent to the corresponding pins so that loop area stays minimal.
Bond the exposed pad to a low-impedance ground plane with a full set of thermal vias placed directly under the pad, because the pad is both the thermal path and the device ground reference. Route SPI clock, data and mode pins on the digital side of the board and keep analog output nets away from them, since coupling from the SPI bus into the headphone and line outputs is a common source of audible clicks and hiss. A clean split between analog and digital ground regions, joined at a single point near the converter, usually preserves more of the 98 dB SNR than a fully interleaved plane.
The achievable dynamic range of this converter depends on master clock quality as much as on the internal converter. Use a low-jitter oscillator or a jitter-cleaned clock, feed the master clock into the package on a short trace with a controlled impedance, and confirm the required master-clock-to-sample-rate ratio for the operating mode in the datasheet. Audio data and latch clock lines should be length-matched and routed away from switching nodes, and the SPI bus should be kept short or series-terminated if the board is large.
Two mistakes dominate in designs built around this converter. First, treating the SPI mode and format pins as decorative: they must be strapped for the interface mode and data format your firmware expects, and a wrong strap produces scrambled audio even though the clocking looks correct. Second, expecting analog input paths - the device has none, so any source signal must arrive digitally. Also verify the headphone mute and switching behavior in firmware before taping out, and keep the audio interface idle until the master clock is stable.
Estimated power use: with a 3.3 V analog and digital supply, a 48 kHz stereo stream and the headphone stage enabled, the converter typically draws only a few tens of milliwatts, but the integrated headphone amplifier adds current that scales with output power into the load. Estimate the headphone dissipation as Vrms squared divided by the headphone impedance, add the converter static current times the supply voltage, and confirm that the supply can deliver the peak current on headphone load transients. Place a bulk capacitor near the headphone supply rail to absorb those transients.
合规信息
A distributor product listing marks the PCM1770RGAR as RoHS3 compliant. No REACH, AEC-Q100, lead-free or halogen-free statements are published for this ordering code in the available listings, so those fields remain unconfirmed; the green (G4) ordering code indicates the lead-free-compliant variant of the same device.