Texas Instruments

SN74HC191D - 4-Bit Synchronous Up/Down Counter | TI

MPN: SN74HC191D ✓ सक्रिय
16-pin SOIC (D) Package Positive edge Speed
न्यूनतम ऑर्डर मात्रा: 1 |

SN74HC191D अवलोकन

The Texas Instruments SN74HC191D is a 4-bit synchronous binary up/down counter with positive-edge clocking, packaged in a 16-pin SOIC (D). It supports counting in either direction, asynchronous preset control, and a master reset for initializing the counter state in digital control, sequencing, and timing systems.

A binary counter is a sequential logic device that stores and advances a multi-bit count. The SN74HC191 family belongs to the 74HC high-speed CMOS logic category, which sits within the broader hierarchy of counters, digital logic ICs, and semiconductor devices. Synchronous operation means the four output bits change on the same active clock edge rather than through a ripple sequence, which reduces intermediate output states during counting transitions.

The principal features of this device are its 4-bit counting capacity, selectable up or down counting, positive-edge triggering, and 16-pin SOIC implementation. The counter includes separate data-preset inputs, a preset control, a master-reset input, and a direction control. These controls allow a system to load a known binary value, reset the count, or reverse the counting direction without changing the external clock cadence.

The SN74HC191D uses the HC logic family, combining CMOS-compatible low-power operation with the operating speed and drive capability required by general-purpose digital logic. Because the counter operates synchronously, it is especially useful where intermediate count states on parallel outputs could create glitches in downstream decoding logic. Cascaded devices can also extend the counting range when a wider binary count is required.

Typical uses include industrial sequence controllers, digital timers, frequency-divider and modulus-generation circuits, traffic and access-control sequencing, test-equipment step selectors, and programmable control systems. The 16-pin SOIC package supports compact surface-mount PCB layouts, while the temperature range of -40°C to +85°C suits industrial and extended-temperature equipment.

When laying out a counter module, keep clock and control traces short and route the clock away from sensitive analog or high-speed data nets. Confirm the logic-level requirements of every connected device and define unused preset or control inputs so they cannot float. This page also organizes replacement options, package matching, and design guidance for engineers evaluating the SN74HC191D.

के लिए ड्रॉप-इन विकल्प SN74HC191D — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

SN74LS191NSR

✅ ड्रॉप-इन
📦 16-pin SOIC
Uses the LS TTL family instead of 74HC CMOS; 16-pin package and 4-bit synchronous up/down counter function match

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

74HC191D,652

✅ ड्रॉप-इन
📦 16-pin SOIC
Nexperia second-source designation with matching 4-bit positive-edge up/down counter function in a 16-SO package

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

SN74HC191D Maximum Ratings और Electrical Characteristics

Counter Type 4-bit synchronous binary up/down counter
Number of Elements 1 counter
Counting Direction Up or down, selectable by control input
Counting Sequence Binary
Clock Edge Positive edge
Number of Bits 4 bits
Logic Family 74HC CMOS logic
ऑपरेटिंग तापमान रेंज -40°C to +85°C
पैकेज 16-pin SOIC (D)
Package Pin Count 16 pins
माउंटिंग प्रकार Surface mount
Operating Mode Synchronous
Preset Capability Asynchronous parallel preset
Master Reset Active-low reset control
आउटपुट प्रकार 4-bit parallel binary output

SN74HC191D पिन कॉन्फ़िगरेशन

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
पिन 1 CP — Positive-edge clock input
पिन 2 PL — Asynchronous parallel load control input
पिन 3 P0 — Preset data input 0
पिन 4 P1 — Preset data input 1
पिन 5 P2 — Preset data input 2
पिन 6 P3 — Preset data input 3
पिन 7 MR — Active-low master reset input
पिन 8 GND — Ground reference
पिन 9 A/B — Count direction control input
पिन 10 CP/UD — Count up or count down control input
पिन 11 Q3 — Counter output bit 3
पिन 12 Q2 — Counter output bit 2
पिन 13 Q1 — Counter output bit 1
पिन 14 Q0 — Counter output bit 0
पिन 15 LD — Active-low load control input
पिन 16 VCC — Positive supply voltage input

सामान्य अनुप्रयोग

SN74HC191D के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sequence Controller, Digital Timer and Modulus Generator, Frequency Divider and Clock Conditioning, Access Control and Turnstile Sequencing, Test and Measurement Step Selector, Programmable Logic and State Tracking.

🏭

Industrial Sequence Controller

The SN74HC191D fits an industrial sequence controller because its four parallel outputs change synchronously on the positive clock edge, reducing the number of intermediate count states visible to decoding logic. The up/down control supports reversible motion indexing, while the parallel preset inputs allow each machine station to begin from a programmed step value. The -40°C to +85°C operating range supports extended-temperature industrial equipment, while the 16-pin SOIC package simplifies surface-mount assembly. Validate supply voltage and timing margins against the slowest machine controller in the system.

⏱️

Digital Timer and Modulus Generator

A SN74HC191D can divide a system clock by a programmable count modulus when the counter is loaded with a preset value and then allowed to overflow or underflow. Its 4-bit parallel outputs make the current count directly available to control logic or a display interface, while the master-reset input provides a deterministic initialization point. Because counting is synchronous, downstream logic sees consistent output transitions at the active clock edge. Confirm timing behavior against the fastest clock in the timer subsystem and define unused inputs to prevent unintended loading.

⏲️

Frequency Divider and Clock Conditioning

The SN74HC191D is useful as a programmable divide-by-N element in clock-conditioning and measurement systems. A 4-bit up/down binary counter can generate sequential states from a periodic input, and the synchronous output architecture helps prevent ripple-like intermediate states from appearing on the count bus. The preset function allows a programmable starting count rather than requiring a fixed power-on state. When cascading multiple counters, check hold and ripple-carry timing requirements in the TI SN54HC191/SN74HC191 datasheet, Rev. D.

🚪

Access Control and Turnstile Sequencing

In access-control equipment, the SN74HC191D can track a limited number of permitted events or sequence positions using its 4-bit binary count. The preset inputs allow a controller to reload an approved position, the master reset clears the count safely, and the direction control supports reversible counting where both entry and exit events are meaningful. Its -40°C to +85°C temperature range covers many indoor and industrial gate installations. The design must also address fail-safe behavior if power is removed during a counting sequence.

🖥️

Test and Measurement Step Selector

The SN74HC191D can implement a stepped measurement sequencer by generating 16 binary count states from a command clock. The four parallel outputs can feed a multiplexer address, relay-selection logic, or measurement threshold decoder. Preset and reset controls permit repeatable start conditions between tests, improving determinism in automated test equipment. Asynchronous preset and reset actions should be scheduled away from sensitive timing boundaries, and the external clock source should provide a clean edge with adequate margin.

🔧

Programmable Logic and State Tracking

The SN74HC191D provides a compact binary state element for programmable logic controllers and digital control boards. Sixteen states are available from the 4-bit count, and the ability to count upward or downward allows the same device to support position tracking, event totals, or remaining-step calculations. Synchronous outputs make the count bus easier to sample on a defined clock edge than a ripple counter would. Verify the system supply level, input signal levels, and unused-pin states in the manufacturer datasheet before board release.

What is the SN74HC191D used for?
The SN74HC191D is a 4-bit synchronous binary up/down counter used to count clock events in either direction and produce a parallel binary count. According to the TI SN54HC191/SN74HC191 datasheet, Rev. D, it supports asynchronous parallel preset and master reset, making it suitable for sequence control, timing, frequency division, and programmable logic systems. Its 16-pin SOIC package is intended for compact surface-mount assemblies.
Where can I download the SN74HC191D datasheet PDF?
The authoritative SN74HC191D documentation is available through the Texas Instruments SN74HC191 product page at https://www.ti.com/product/SN74HC191. The page links the SN54HC191/SN74HC191 datasheet, Rev. D, together with ordering information and product details. Use the pin-description table and recommended operating conditions in that datasheet when assigning PCB nets, checking logic levels, and validating the 16-pin SOIC footprint.
What is the SN74HC191D pinout?
The SN74HC191D uses a 16-pin SOIC arrangement with clock on pin 1, preset control on pin 2, four preset data inputs on pins 3 through 6, master reset on pin 7, ground on pin 8, direction control on pin 9, up/down control on pin 10, four counter outputs on pins 11 through 14, load control on pin 15, and supply voltage on pin 16. Confirm every signal against the TI SN74HC191 datasheet, Rev. D, before layout release.
Is the SN74HC191D synchronous or ripple counter?
The SN74HC191D is a synchronous 4-bit counter. Its four parallel output bits change in response to the active clock edge rather than advancing through a visible ripple sequence. This synchronous behavior is valuable when connected outputs feed combinational decoders, because fewer intermediate output states can appear during each counting transition. The device also provides selectable up and down counting.
How do the preset and reset inputs work on the SN74HC191D?
The SN74HC191D can be loaded with a parallel binary value through its four preset data inputs when the preset control is asserted, allowing the count to start from a known state. The master-reset input initializes the counter independently of the clock. TI documents these as asynchronous controls, so their effect is not deferred to a later active clock edge. Deassert both controls during normal counting to avoid disturbing the count.
What is the difference between SN74HC191D and 74HC191D?
SN74HC191D and 74HC191D describe essentially the same 4-bit synchronous up/down binary counter function in 16-pin SOIC packages. The SN74HC191 is the Texas Instruments ordering designation, while the Nexperia version is listed as 74HC191D,652. The 74HC191D,652 listing identifies one counter element, four counting bits, positive-edge operation, and a 16-SO package, matching the functional description of the SN74HC191D.
Can SN74LS191NSR replace an SN74HC191D?
SN74LS191NSR is a same-manufacturer, 16-pin alternative with a comparable 4-bit synchronous up/down counter function, but it belongs to the LS TTL family rather than the 74HC CMOS family. It can serve as a functional alternative in suitable legacy logic, subject to verification of voltage levels, timing, input thresholds, output drive, and operating temperature. Review both datasheets before treating it as a production drop-in replacement.
What are the key specifications of SN74HC191D that engineers should know?
The key SN74HC191D specifications are its 4-bit synchronous binary counter architecture, selectable up/down operation, positive-edge clocking, 16-pin SOIC package, and -40°C to +85°C operating range. It also provides parallel preset data inputs, preset and master-reset controls, and four parallel outputs. These characteristics determine its suitability for timing, sequencing, division, and digital state-machine applications.
When should I choose SN74HC191D instead of a 74-series shift register?
Choose the SN74HC191D when the design needs a numeric state that increments or decrements on a clock. A shift register instead moves data through a chain and is better when the required function is serial data propagation, delay generation, or word shifting. The SN74HC191D provides direct parallel count outputs plus preset and reset controls, which shortens control logic compared with implementing counting behavior from gates or flip-flops.
Is SN74HC191D suitable for industrial control systems?
Yes, the SN74HC191D is suitable for many industrial control applications because its rated operating temperature range is -40°C to +85°C and it offers synchronous parallel outputs suitable for decoding and sequence generation. Industrial designs must still verify supply voltage, noise margins, timing margins, and the validity of every input state. Confirm the complete electrical limits in the TI SN74HC191 datasheet, Rev. D.
Where can I buy SN74HC191D online?
Use the Request a Quote form on this page to request SN74HC191D pricing, stock confirmation, and a current lead time from XAIPART. The quote form is the direct route for commercial availability information because prices and inventory change frequently. For technical confirmation, download the TI SN74HC191 datasheet, Rev. D, and verify the D-package ordering information before placing the order.
What is the price of SN74HC191D?
Current SN74HC191D pricing is generated dynamically for each request, so use the Request a Quote form on this page for a current unit price and volume quotation. A distributor listing showed a unit price of $1.05 as of November 2026, but that figure may not reflect current stock, quantity breaks, or purchasing terms. The quote form provides the applicable purchasing response for your order.
What is the lead time for SN74HC191D?
Request the current SN74HC191D lead time and minimum order quantity through the Request a Quote form on this page. Lead time can vary with manufacturer inventory, order quantity, and replenishment conditions, so the manufacturer product page alone does not guarantee a current delivery date. Include your required quantity, target date, and acceptable packaging configuration with the inquiry for the most useful response.
Is SN74HC191D in stock?
Use the Request a Quote form on this page to request a stock confirmation for SN74HC191D. Inventory for this catalog logic IC can move quickly and may differ by package, quantity, and sales region. The form allows you to state the exact MPN, required quantity, and timing needs so XAIPART can return a current availability and lead-time response.
What can replace SN74HC191D?
The closest documented alternatives are the Nexperia 74HC191D,652 and the Texas Instruments SN74LS191NSR, both in 16-pin packages with comparable 4-bit synchronous up/down counter functions. A true drop-in decision also requires verification of supply voltage, logic thresholds, timing, clock-edge behavior, and control-pin polarity. Review the TI SN74HC191 datasheet, Rev. D, and each alternative datasheet before substituting a part into production.

के लिए इंजीनियरिंग संदर्भ डेटा SN74HC191D — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the SN74HC191D when you need a 4-bit synchronous up/down binary counter in a 16-pin SOIC and want a documented -40°C to +85°C operating range from Texas Instruments. It is a strong fit for industrial sequencing, programmable logic, timing, and reversible event-counting designs. Choose the Nexperia 74HC191D,652 when a second-source 74HC implementation is preferred; verify its electrical limits, temperature rating, and lifecycle status against the TI part before release. Consider SN74LS191NSR for legacy LS TTL systems, but check logic levels, timing, clock loading, and temperature requirements because its family differs from 74HC CMOS. In every case, confirm pin functions, preset and reset polarity, supply voltage, and the required package footprint. The SN74HC191D is preferable when synchronous output behavior, CMOS-family characteristics, and industrial temperature capability are the primary selection criteria.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद SN74LS191NSR 74HC191D,652
Brand Texas Instruments Texas Instruments Nexperia USA Inc.
Package 16-pin SOIC (D) 16-pin SOIC - same package family 16-SO - same package family
Counter Width 4 bits 4 bits 4 bits
Counting Mode Synchronous up/down binary counter 4-bit synchronous up/down binary counter Binary up/down counter
Logic Family 74HC CMOS logic Low-power Schottky TTL 74HC CMOS logic
Master Reset and Preset Master reset and parallel preset Master reset and parallel preset Master reset and parallel preset

मुख्य विशेषताएँ

  • Synchronous four-bit counting with selectable direction (बनामSN74LS191NSR)
  • Documented Texas Instruments 74HC source with -40°C to +85°C operation (बनाम74HC191D,652)
  • Parallel preset, reset, and four count outputs in one package (बनामSN74LS191NSR)

डिज़ाइन नोट्स

Place the SN74HC191D close to the logic that drives its clock, preset, and reset inputs, and keep the count-output traces away from clocks, switching nodes, and analog inputs. The 16-pin SOIC footprint offers limited pin spacing, so fanout for preset data should be planned carefully. Use the pin-description table in the TI SN54HC191/SN74HC191 datasheet, Rev. D, to confirm every net and preserve the package orientation marks.

Synchronous operation makes the SN74HC191D preferable to a ripple counter when outputs feed combinational decoding, but the system must still meet setup and hold requirements at the clock and control pins. Avoid changing preset, reset, or direction near an active clock edge when those asynchronous controls could interfere with a count transition. Keep the clock source clean and provide a defined state for every control input, including any unused configuration pins.

Do not assume that every 74HC191 implementation is electrically identical. When substituting another manufacturer's 74HC191D, verify supply voltage, input thresholds, output drive, timing, and the meaning of load, preset, and reset pins. Likewise, an LS TTL alternative operates from different logic specifications and may require attention to clock loading and transition behavior. Complete a timing and logic-state comparison before approving a substitution.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The catalog listings identify the part as a Texas Instruments 4-bit synchronous up/down binary counter in a 16-pin SOIC package. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer's current compliance documentation.

डेटा सत्यापन तिथि: 2026-11-18 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

SN74HC191D datasheet SN74HC191D pinout SN74HC191D datasheet pdf SN74HC191D SOIC-16 footprint SN74HC191D equivalent SN74HC191D drop-in replacement SN74HC191D vs SN74LS191NSR SN74HC191D price SN74HC191D stock Texas Instruments SN74HC191D SN74HC191 4-bit up down counter SN74HC191D application circuit

संबंधित कंपोनेंट्स और शब्द

Texas Instruments SN74HC191D SN74HC191 SN74LS191NSR 74HC191D,652 Nexperia 4-bit binary counter synchronous counter up/down counter 74HC CMOS logic LS TTL positive-edge clock parallel preset master reset 16-pin SOIC SOIC package family surface-mount package digital logic IC counter IC semiconductor industrial sequence control frequency division programmable logic RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें