SN74HC191D - 4-Bit Synchronous Up/Down Counter | TI
MPN: SN74HC191D ✓ פעילSN74HC191D סקירה
A binary counter is a sequential logic device that stores and advances a multi-bit count. The SN74HC191 family belongs to the 74HC high-speed CMOS logic category, which sits within the broader hierarchy of counters, digital logic ICs, and semiconductor devices. Synchronous operation means the four output bits change on the same active clock edge rather than through a ripple sequence, which reduces intermediate output states during counting transitions.
The principal features of this device are its 4-bit counting capacity, selectable up or down counting, positive-edge triggering, and 16-pin SOIC implementation. The counter includes separate data-preset inputs, a preset control, a master-reset input, and a direction control. These controls allow a system to load a known binary value, reset the count, or reverse the counting direction without changing the external clock cadence.
The SN74HC191D uses the HC logic family, combining CMOS-compatible low-power operation with the operating speed and drive capability required by general-purpose digital logic. Because the counter operates synchronously, it is especially useful where intermediate count states on parallel outputs could create glitches in downstream decoding logic. Cascaded devices can also extend the counting range when a wider binary count is required.
Typical uses include industrial sequence controllers, digital timers, frequency-divider and modulus-generation circuits, traffic and access-control sequencing, test-equipment step selectors, and programmable control systems. The 16-pin SOIC package supports compact surface-mount PCB layouts, while the temperature range of -40°C to +85°C suits industrial and extended-temperature equipment.
When laying out a counter module, keep clock and control traces short and route the clock away from sensitive analog or high-speed data nets. Confirm the logic-level requirements of every connected device and define unused preset or control inputs so they cannot float. This page also organizes replacement options, package matching, and design guidance for engineers evaluating the SN74HC191D.
חלופות תחליף ישיר עבור SN74HC191D — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
SN74LS191NSR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
74HC191D,652
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SN74HC191D דירוגים מרביים ומאפיינים חשמליים
| Counter Type | 4-bit synchronous binary up/down counter |
| Number of Elements | 1 counter |
| Counting Direction | Up or down, selectable by control input |
| Counting Sequence | Binary |
| Clock Edge | Positive edge |
| Number of Bits | 4 bits |
| Logic Family | 74HC CMOS logic |
| טווח טמפרטורת פעולה | -40°C to +85°C |
| מארז | 16-pin SOIC (D) |
| Package Pin Count | 16 pins |
| סוג הרכבה | Surface mount |
| Operating Mode | Synchronous |
| Preset Capability | Asynchronous parallel preset |
| Master Reset | Active-low reset control |
| סוג פלט | 4-bit parallel binary output |
תצורת פינים של SN74HC191D
| פין 1 | CP — Positive-edge clock input |
| פין 2 | PL — Asynchronous parallel load control input |
| פין 3 | P0 — Preset data input 0 |
| פין 4 | P1 — Preset data input 1 |
| פין 5 | P2 — Preset data input 2 |
| פין 6 | P3 — Preset data input 3 |
| פין 7 | MR — Active-low master reset input |
| פין 8 | GND — Ground reference |
| פין 9 | A/B — Count direction control input |
| פין 10 | CP/UD — Count up or count down control input |
| פין 11 | Q3 — Counter output bit 3 |
| פין 12 | Q2 — Counter output bit 2 |
| פין 13 | Q1 — Counter output bit 1 |
| פין 14 | Q0 — Counter output bit 0 |
| פין 15 | LD — Active-low load control input |
| פין 16 | VCC — Positive supply voltage input |
יישומים טיפוסיים
SN74HC191D מתאים עבור 6 יישוםs: Industrial Sequence Controller, Digital Timer and Modulus Generator, Frequency Divider and Clock Conditioning, Access Control and Turnstile Sequencing, Test and Measurement Step Selector, Programmable Logic and State Tracking.
Industrial Sequence Controller
The SN74HC191D fits an industrial sequence controller because its four parallel outputs change synchronously on the positive clock edge, reducing the number of intermediate count states visible to decoding logic. The up/down control supports reversible motion indexing, while the parallel preset inputs allow each machine station to begin from a programmed step value. The -40°C to +85°C operating range supports extended-temperature industrial equipment, while the 16-pin SOIC package simplifies surface-mount assembly. Validate supply voltage and timing margins against the slowest machine controller in the system.
מומלץ
Digital Timer and Modulus Generator
A SN74HC191D can divide a system clock by a programmable count modulus when the counter is loaded with a preset value and then allowed to overflow or underflow. Its 4-bit parallel outputs make the current count directly available to control logic or a display interface, while the master-reset input provides a deterministic initialization point. Because counting is synchronous, downstream logic sees consistent output transitions at the active clock edge. Confirm timing behavior against the fastest clock in the timer subsystem and define unused inputs to prevent unintended loading.
מומלץ
Frequency Divider and Clock Conditioning
The SN74HC191D is useful as a programmable divide-by-N element in clock-conditioning and measurement systems. A 4-bit up/down binary counter can generate sequential states from a periodic input, and the synchronous output architecture helps prevent ripple-like intermediate states from appearing on the count bus. The preset function allows a programmable starting count rather than requiring a fixed power-on state. When cascading multiple counters, check hold and ripple-carry timing requirements in the TI SN54HC191/SN74HC191 datasheet, Rev. D.
מומלץ
Access Control and Turnstile Sequencing
In access-control equipment, the SN74HC191D can track a limited number of permitted events or sequence positions using its 4-bit binary count. The preset inputs allow a controller to reload an approved position, the master reset clears the count safely, and the direction control supports reversible counting where both entry and exit events are meaningful. Its -40°C to +85°C temperature range covers many indoor and industrial gate installations. The design must also address fail-safe behavior if power is removed during a counting sequence.
מומלץ
Test and Measurement Step Selector
The SN74HC191D can implement a stepped measurement sequencer by generating 16 binary count states from a command clock. The four parallel outputs can feed a multiplexer address, relay-selection logic, or measurement threshold decoder. Preset and reset controls permit repeatable start conditions between tests, improving determinism in automated test equipment. Asynchronous preset and reset actions should be scheduled away from sensitive timing boundaries, and the external clock source should provide a clean edge with adequate margin.
מומלץ
Programmable Logic and State Tracking
The SN74HC191D provides a compact binary state element for programmable logic controllers and digital control boards. Sixteen states are available from the 4-bit count, and the ability to count upward or downward allows the same device to support position tracking, event totals, or remaining-step calculations. Synchronous outputs make the count bus easier to sample on a defined clock edge than a ripple counter would. Verify the system supply level, input signal levels, and unused-pin states in the manufacturer datasheet before board release.
מומלץ
נתוני עזר הנדסיים עבור SN74HC191D — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | SN74LS191NSR | 74HC191D,652 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Nexperia USA Inc. |
| Package | 16-pin SOIC (D) | 16-pin SOIC - same package family | 16-SO - same package family |
| Counter Width | 4 bits | 4 bits | 4 bits |
| Counting Mode | Synchronous up/down binary counter | 4-bit synchronous up/down binary counter | Binary up/down counter |
| Logic Family | 74HC CMOS logic | Low-power Schottky TTL | 74HC CMOS logic |
| Master Reset and Preset | Master reset and parallel preset | Master reset and parallel preset | Master reset and parallel preset |
מבדילים עיקריים
- Synchronous four-bit counting with selectable direction (לעומתSN74LS191NSR)
- Documented Texas Instruments 74HC source with -40°C to +85°C operation (לעומת74HC191D,652)
- Parallel preset, reset, and four count outputs in one package (לעומתSN74LS191NSR)
הערות תכנון
Place the SN74HC191D close to the logic that drives its clock, preset, and reset inputs, and keep the count-output traces away from clocks, switching nodes, and analog inputs. The 16-pin SOIC footprint offers limited pin spacing, so fanout for preset data should be planned carefully. Use the pin-description table in the TI SN54HC191/SN74HC191 datasheet, Rev. D, to confirm every net and preserve the package orientation marks.
Synchronous operation makes the SN74HC191D preferable to a ripple counter when outputs feed combinational decoding, but the system must still meet setup and hold requirements at the clock and control pins. Avoid changing preset, reset, or direction near an active clock edge when those asynchronous controls could interfere with a count transition. Keep the clock source clean and provide a defined state for every control input, including any unused configuration pins.
Do not assume that every 74HC191 implementation is electrically identical. When substituting another manufacturer's 74HC191D, verify supply voltage, input thresholds, output drive, timing, and the meaning of load, preset, and reset pins. Likewise, an LS TTL alternative operates from different logic specifications and may require attention to clock loading and transition behavior. Complete a timing and logic-state comparison before approving a substitution.
מידע על תאימות
The catalog listings identify the part as a Texas Instruments 4-bit synchronous up/down binary counter in a 16-pin SOIC package. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer's current compliance documentation.