Texas Instruments

SN74HC367D - 6-Channel Tri-State Buffer | Texas Instruments

MPN: SN74HC367D ✓ सक्रिय
2 V to 6 V Vdss 7.8 mA Id 16-pin SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

SN74HC367D अवलोकन

The Texas Instruments SN74HC367D is a six-channel non-inverting CMOS buffer and line driver with three-state outputs, a 2 V to 6 V operating supply, and a 16-pin SOIC package. It organizes its six channels into two independently controlled banks: one bank contains four drivers and the other contains two drivers. Each bank has its own output-enable input, allowing four outputs and two outputs to enter the high-impedance state independently.

A tri-state buffer is a digital logic device that passes a logic signal without inversion while adding electrical drive strength. In the high-impedance state, its output stops actively driving the connected net, allowing several drivers to share a bus without creating contention. The SN74HC367 belongs to the CMOS buffer and line-driver hierarchy, where it provides isolation, improved signal integrity, and bus-compatible output control.

The principal features of the SN74HC367D include six non-inverting channels, three-state outputs, two independently enabled output banks, and operation from 2 V to 6 V. Its four-channel bank provides common control for four interconnections, while its two-channel bank supports a separate two-wire group. This arrangement is useful when a system needs shared data, address, or control lines to be disconnected selectively.

The two-bank architecture is the device's principal technical feature. A high level on an output-enable input places the corresponding bank in the high-impedance state, while a low level enables active output drive. Because enable control is organized independently, a design can disable four channels while retaining two outputs, or isolate a two-channel group without affecting the four-channel bank. The exact propagation-delay, output-current, and static-current limits should be taken from the manufacturer datasheet for the selected operating voltage.

Typical uses include bus isolation, bidirectional bus transceivers, memory interfacing, data acquisition systems, and digital control boards. The SN74HC367D is particularly useful when multiple logic devices can drive a shared line but must be disconnected during selected operating intervals. It can also provide stronger source and sink capability than the driving logic device when operating within its specified limits.

PCB design should route each enable input away from high-speed output nets, place the device close to the shared bus, and keep input and output return paths compact. Unused inputs must be tied to a defined logic level rather than left floating. Because three-state outputs do not actively hold a bus low when disabled, external pull-up or pull-down resistors may be needed when the bus must remain at a defined state during high-impedance periods.

This product page combines the manufacturer functional description, package and supply information, commercial sourcing details, a technically structured feature summary, and practical guidance for bus isolation and tri-state output design. These engineering-focused details help engineers distinguish the SN74HC367D from general-purpose unidirectional buffers while supporting footprint, signal-integrity, and replacement decisions.

के लिए ड्रॉप-इन विकल्प SN74HC367D — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

74HC367D,653

✅ ड्रॉप-इन
📦 SOIC-16
Six channels and tri-state enable architecture unchanged (0% channel-count difference); detailed timing and output-current deltas are

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

SN74HC367D Maximum Ratings और Electrical Characteristics

Number of Channels 6 channels
ऑपरेटिंग सप्लाई वोल्टेज 2 V to 6 V
Logic Type Non-inverting CMOS buffer and line driver
Output State 3-state output
Output Bank Configuration One 4-channel bank and one 2-channel bank
Output Enable Control One independent enable for each output bank
High-Impedance Control Enabled by a HIGH on the corresponding output-enable input
क्वाइसेंट करंट 7.8 mA
ऑपरेटिंग तापमान रेंज -40 °C to +85 °C
पैकेज 16-pin SOIC
माउंटिंग प्रकार Surface mount
Logic Level CMOS
Output Bank Sizes 4 outputs and 2 outputs
Signal Direction Unidirectional
Voltage-Level Translation Function Unidirectional
RoHS स्थिति Compliant

SN74HC367D पिन कॉन्फ़िगरेशन

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
पिन 1 1A — Data input for output 1
पिन 2 2A — Data input for output 2
पिन 3 GND — Ground
पिन 4 3A — Data input for output 3
पिन 5 4A — Data input for output 4
पिन 6 2Y — Buffer output 2
पिन 7 1Y — Buffer output 1
पिन 8 3Y — Buffer output 3
पिन 9 4Y — Buffer output 4
पिन 10 3OE — Output enable for the four-output bank
पिन 11 4OE — Output enable for the four-output bank
पिन 12 1OE — Output enable for the two-output bank
पिन 13 2OE — Output enable for the two-output bank
पिन 14 VCC — Power supply
पिन 15 5A — Data input for output 5
पिन 16 6A — Data input for output 6

सामान्य अनुप्रयोग

SN74HC367D के लिए उपयुक्त है 6 अनुप्रयोगs: Shared Digital Bus Isolation, Memory and Peripheral Interface, Data Acquisition Backplane, Digital Control Board, Bus Transceiver Support, Communication and Network Equipment.

🖥️

Shared Digital Bus Isolation

The SN74HC367D fits shared-bus isolation because it provides six non-inverting three-state outputs over a 2 V to 6 V supply. According to the Texas Instruments manufacturer datasheet, the outputs are arranged as one four-channel bank and one two-channel bank, each with its own output-enable input. Placing the buffer near the bus allows a four-device group to be disconnected while two outputs remain active, or the reverse. Confirm propagation delay and bus transition requirements against the system timing, and add a pull-up or pull-down when a disabled bus must retain a defined voltage.

🔧

Memory and Peripheral Interface

The SN74HC367D can buffer address, data, or peripheral-control lines on a 2 V to 6 V logic board. Its six non-inverting channels and two independent enable groups provide enough control granularity to isolate one interface section while maintaining another. According to the Texas Instruments manufacturer datasheet, a HIGH on an output-enable input places the associated bank in the high-impedance state. This is useful when several devices may contend for a bus, although the design must define the disabled-line state and verify timing margins at the intended voltage and load.

📡

Data Acquisition Backplane

The SN74HC367D is useful in data-acquisition backplanes where several instrument or digitizer boards can connect to a common control or data bus. Its six tri-state outputs provide active drive for the connected logic while allowing the four-channel and two-channel banks to be disabled independently. According to the Texas Instruments manufacturer datasheet, the device operates from 2 V to 6 V and offers non-inverting signal transmission. Layout should keep the shared traces away from enable inputs, and external bias resistors should maintain valid levels whenever all participating drivers enter the high-impedance state.

🏭

Digital Control Board

A 5 V industrial or embedded control board can use the SN74HC367D to combine signal buffering, drive strength, and grouped high-impedance control. According to the Texas Instruments manufacturer datasheet, the device supports a 2 V to 6 V supply and contains six non-inverting channels with separate four-output and two-output enable banks. This arrangement simplifies routing when four connector or peripheral lines need to be released together. Engineers should verify output-current capability, input thresholds, propagation delay, and the state of every potentially floating bus during enable transitions.

🌐

Bus Transceiver Support

The SN74HC367D can support the receive or drive side of a bus transceiver by providing non-inverting buffers with controllable high-impedance outputs. According to the Texas Instruments manufacturer datasheet, its independent four-channel and two-channel banks let a designer disable groups of external connections while keeping other interfaces operational. The device does not reverse signal direction, so it should be paired with direction-control logic when a bidirectional bus requires true transmit and receive switching. Validate setup and hold timing at the selected supply voltage and ensure that disabled outputs are externally biased when required.

🌐

Communication and Network Equipment

The SN74HC367D fits communication equipment that requires several internal lines to connect and disconnect cleanly on a shared bus. Its six non-inverting, three-state channels operate from 2 V to 6 V and are divided into independently controlled banks, allowing one link group to be isolated without disabling the complete device. According to the Texas Instruments manufacturer datasheet, this two-bank organization is inherent to the SN74HC367 architecture. Place the component near the shared connector or backplane, keep enable traces quiet, and verify that loss of all drivers does not leave a control or status line at an undefined voltage.

अनुशंसित उत्पादों का सारांश

SN74HC367D Texas Instruments उपयोग में: Shared Digital Bus Isolation, Memory and Peripheral Interface, Data Acquisition Backplane, Digital Control Board, Bus Transceiver Support, Communication and Network Equipment 74HC367D,653 Drop-in alternative for the same bus-buffer function उपयोग में: Shared Digital Bus Isolation, Memory and Peripheral Interface, Data Acquisition Backplane, Digital Control Board, Bus Transceiver Support, Communication and Network Equipment
What is the SN74HC367D and what does it do?
The SN74HC367D is a six-channel, non-inverting CMOS buffer and line driver with independently enabled three-state outputs. According to the Texas Instruments manufacturer datasheet, the device operates from 2 V to 6 V and is divided into one four-driver bank and one two-driver bank. Each bank has a separate output-enable input, allowing a designer to disconnect either group and place its outputs in the high-impedance state without changing the logic data.
Where can I download the SN74HC367D datasheet PDF?
The official SN74HC367D datasheet is available from the Texas Instruments literature link for the SN74HC367 family. It documents the six-channel buffer arrangement, the two output-enable banks, operating conditions, electrical characteristics, and pin assignments. Engineers should use the manufacturer datasheet to confirm propagation delay, output-current capability, input thresholds, and recommended operating conditions at the voltage and load applicable to the design.
What is the SN74HC367D pinout?
The SN74HC367D uses a 16-pin SOIC with six data inputs, six outputs, two output-enable inputs, VCC, and ground. According to the Texas Instruments manufacturer datasheet, the enable inputs control separate four-output and two-output banks. Place the enable pins near the device and route them away from the output buses to reduce susceptibility to crosstalk; unused inputs should be connected to a valid logic level rather than left floating.
How does the SN74HC367D three-state output work?
A HIGH level on an SN74HC367D output-enable input places the corresponding output bank in the high-impedance state. According to the Texas Instruments manufacturer datasheet, the four-driver bank and two-driver bank are controlled independently, so one group can be disabled while the other continues driving. A disabled output does not hold a shared bus at a defined level, which can require a suitable pull-up or pull-down resistor.
What is the difference between SN74HC367D and 74HC367D from Nexperia?
The SN74HC367D and Nexperia 74HC367D,653 both provide six non-inverting channels, three-state outputs, separate four-channel and two-channel enable banks, and a 16-pin SOIC footprint. According to the manufacturer and distributor product descriptions, their externally visible functions are closely aligned. Detailed propagation-delay, current, and temperature-limit comparisons should be completed against each manufacturer datasheet before treating either part as a drop-in replacement.
Can 74HC367D,653 replace SN74HC367D without PCB changes?
The Nexperia 74HC367D,653 is a candidate drop-in replacement for the Texas Instruments SN74HC367D because both use a 16-pin SOIC and implement six non-inverting three-state buffer channels with independent four-channel and two-channel enable banks. According to the Texas Instruments and Nexperia product descriptions, the functional architecture matches. Confirm pin orientation, enable polarity, operating voltage, timing, and output-current limits against both datasheets before production use.
When should I choose SN74HC367D instead of a single-channel buffer?
Choose the SN74HC367D when one board must isolate or drive several shared digital lines. According to the Texas Instruments manufacturer datasheet, its six outputs are organized into independently controlled banks of four and two, which supports grouped bus enablement without using six separate enable circuits. A single-channel buffer may be preferable for an isolated point-to-point path, but the SN74HC367D offers greater integration where several lines require coordinated three-state control.
Is SN74HC367D suitable for bus isolation and memory interfaces?
The SN74HC367D is suitable for applications requiring grouped bus isolation because it provides six non-inverting three-state outputs and two independent enable controls. According to the Texas Instruments manufacturer datasheet, the four-output bank and two-output bank can be enabled separately, allowing one group to remain active while the other enters the high-impedance state. The design must also account for bus turnaround timing and the electrical state of a disabled shared line.
What can replace the SN74HC367D?
The Nexperia 74HC367D,653 is the closest documented drop-in candidate because it has the same six-channel, non-inverting, three-state architecture in a 16-pin SOIC package. According to the Texas Instruments and Nexperia product descriptions, both devices split the outputs into independently controlled four-channel and two-channel banks. Confirm timing, output drive, temperature ratings, and enable polarity against both manufacturer datasheets before substitution.
How do I calculate the high-impedance behavior of an SN74HC367D bus?
The SN74HC367D stops actively driving a bus when its corresponding output-enable input is HIGH, so the resulting voltage is then determined by the bus, connected devices, and any external bias network. According to the Texas Instruments manufacturer datasheet, the four-channel and two-channel banks can be disabled independently. For a shared line, calculate the required pull-up or pull-down resistance using the bus capacitance, leakage, voltage target, and the maximum transition rate permitted by the system.
What are the key specifications of SN74HC367D that engineers should know?
The SN74HC367D is a six-channel, non-inverting, 2 V to 6 V CMOS buffer and line driver with three-state outputs. According to the Texas Instruments manufacturer datasheet, it provides one four-output bank and one two-output bank, each with an independent output-enable control. The device is offered in a 16-pin SOIC package and is specified for operation from -40 °C to +85 °C. Propagation delay and output-current values are design-dependent and should be read from the manufacturer electrical-characteristics tables.
Can I use SN74HC367D at 5 V in a digital control board?
The SN74HC367D can operate from a 2 V to 6 V supply, making it compatible with a 5 V CMOS control domain when all connected devices use compatible input thresholds and signal levels. According to the Texas Instruments manufacturer datasheet, the part is a six-channel non-inverting buffer with two independently controlled three-state banks. Check the input and output voltage limits, propagation delay, fanout, and total input current for the specific 5 V design.
What is the lead time and stock status of SN74HC367D?
Current stock, minimum order quantity, and production lead time should be requested through the Request a Quote form on this page. According to the Texas Instruments product page, the SN74HC367 family is available for ordering, and the SN74HC367D is listed in a 16-pin SOIC package. The form lets procurement confirm current availability, authorized-channel sourcing, quantity breaks, and the expected delivery schedule for the exact manufacturer part number.
Where can I buy SN74HC367D and check its current price?
Use the Request a Quote form on this page to request the current price, stock, minimum order quantity, and lead time for the exact SN74HC367D. According to the Texas Instruments product page, the device is a 2 V to 6 V six-channel tri-state buffer, while the distributor listing identifies the exact orderable SN74HC367D configuration in a 16-pin SOIC package. Requesting the exact MPN helps prevent confusion with family members or different package suffixes.
How should an SN74HC367D PCB layout handle enable and output nets?
Place the SN74HC367D close to the shared bus and route each output-enable input away from the corresponding output nets to minimize coupling. According to the Texas Instruments manufacturer datasheet, the device contains independent four-channel and two-channel three-state banks, making control routing especially important where one bank can remain active while the other is disabled. Use a defined logic state for unused inputs and check whether each disabled bus requires an external pull-up or pull-down.
Is the SN74HC367D RoHS compliant?
The SN74HC367D is identified as RoHS compliant in its component listing. According to the Texas Instruments manufacturer datasheet, it is a commercial-temperature, 2 V to 6 V six-channel three-state buffer in a 16-pin SOIC package. RoHS status addresses restricted substances in the component and its supplied materials; it does not by itself establish halogen-free status, conflict-minerals reporting, or automotive qualification, which should be confirmed separately for the exact sourcing configuration.

के लिए इंजीनियरिंग संदर्भ डेटा SN74HC367D — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the SN74HC367D when a design needs six non-inverting tri-state channels and separate enable control for groups of four and two outputs. It is particularly suitable for shared buses, memory interfaces, backplanes, and control boards operating from 2 V to 6 V. The Nexperia 74HC367D,653 is the closest documented drop-in alternative because it uses the same 16-pin SOIC footprint and implements the same six-channel, two-bank architecture. Review both datasheets for timing, output-current, temperature, and lifecycle requirements before substitution. Neither option provides signal inversion, true bidirectional operation, or voltage-level translation across incompatible logic thresholds. For a design that must preserve the disabled bus at a defined voltage, use suitable pull-up or pull-down resistors and verify the resulting rise or fall time with the worst-case bus capacitance.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद 74HC367D,653
Package SOIC-16 SOIC-16
Brand Texas Instruments Nexperia
Number of Channels 6 channels 6 channels
Logic Polarity Non-inverting Non-inverting
Output Configuration 3-state output 3-state output
Output Bank Configuration One 4-channel bank and one 2-channel bank One 4-channel bank and one 2-channel bank

मुख्य विशेषताएँ

  • Independent control of four-output and two-output banks (बनाम74HC367D,653)
  • Six non-inverting channels in one 16-pin package (बनाम74HC367D,653)
  • Wide 2 V to 6 V operating range (बनाम74HC367D,653)

डिज़ाइन नोट्स

Route the two output-enable inputs away from the six output nets and the shared bus. The enable signals control separate four-output and two-output banks, so crosstalk on either control line can release or disable an unintended group. Place the SN74HC367D close to the bus connector or transceiver, keep the ground return continuous, and follow the manufacturer input and output timing tables when evaluating propagation-delay margins.

A tri-state output does not retain a valid logic level while it is in the high-impedance state. If all devices connected to a bus can become disabled, add an external pull-up or pull-down sized for the bus capacitance, leakage, and required transition rate. Also connect every unused data input to VCC or GND according to the manufacturer logic requirements; do not leave an input floating.

Place input and output decoupling close to the device and preserve a low-impedance ground connection beneath the circuit. Avoid routing the shared bus beneath noisy clock, power-converter, or high-current return paths. Because the SN74HC367D has independent four-channel and two-channel enable banks, separate the associated connector or device groups logically on the board so enable transitions cannot unintentionally affect another subsystem.

The SN74HC367D operates from 2 V to 6 V, so verify that connected CMOS devices use compatible input thresholds and that all output voltages remain within their allowed ranges. Check high-level and low-level output current before driving several loads. The listed 7.8 mA quiescent current should be included in the system power budget, with additional load current added for every enabled channel and enabled external bus load.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

RoHS compliance is identified in the component listing. REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information. AEC-Q100 qualification is not indicated for this commercial-temperature device.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

SN74HC367D datasheet SN74HC367D pinout SN74HC367D datasheet pdf SN74HC367D equivalent SN74HC367D replacement SN74HC367D cross reference SN74HC367D vs 74HC367D,653 SN74HC367D footprint SN74HC367D price SN74HC367D stock Texas Instruments SN74HC367D SN74HC367D 2V to 6V SN74HC367D tri-state buffer SN74HC367D bus isolation SN74HC367D SOIC-16 pinout

संबंधित कंपोनेंट्स और शब्द

Texas Instruments SN74HC367D SN74HC367 74HC367D,653 Nexperia hex buffer logic buffer line driver tri-state output CMOS logic non-inverting buffer output enable high-impedance state bus isolation SOIC-16 surface mount 2 V to 6 V 7.8 mA RoHS memory interface data acquisition communication equipment digital control board output bank
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें