SN74HC367D - 6-Channel Tri-State Buffer | Texas Instruments
MPN: SN74HC367D ✓ AktifSN74HC367D Ringkasan
A tri-state buffer is a digital logic device that passes a logic signal without inversion while adding electrical drive strength. In the high-impedance state, its output stops actively driving the connected net, allowing several drivers to share a bus without creating contention. The SN74HC367 belongs to the CMOS buffer and line-driver hierarchy, where it provides isolation, improved signal integrity, and bus-compatible output control.
The principal features of the SN74HC367D include six non-inverting channels, three-state outputs, two independently enabled output banks, and operation from 2 V to 6 V. Its four-channel bank provides common control for four interconnections, while its two-channel bank supports a separate two-wire group. This arrangement is useful when a system needs shared data, address, or control lines to be disconnected selectively.
The two-bank architecture is the device's principal technical feature. A high level on an output-enable input places the corresponding bank in the high-impedance state, while a low level enables active output drive. Because enable control is organized independently, a design can disable four channels while retaining two outputs, or isolate a two-channel group without affecting the four-channel bank. The exact propagation-delay, output-current, and static-current limits should be taken from the manufacturer datasheet for the selected operating voltage.
Typical uses include bus isolation, bidirectional bus transceivers, memory interfacing, data acquisition systems, and digital control boards. The SN74HC367D is particularly useful when multiple logic devices can drive a shared line but must be disconnected during selected operating intervals. It can also provide stronger source and sink capability than the driving logic device when operating within its specified limits.
PCB design should route each enable input away from high-speed output nets, place the device close to the shared bus, and keep input and output return paths compact. Unused inputs must be tied to a defined logic level rather than left floating. Because three-state outputs do not actively hold a bus low when disabled, external pull-up or pull-down resistors may be needed when the bus must remain at a defined state during high-impedance periods.
This product page combines the manufacturer functional description, package and supply information, commercial sourcing details, a technically structured feature summary, and practical guidance for bus isolation and tri-state output design. These engineering-focused details help engineers distinguish the SN74HC367D from general-purpose unidirectional buffers while supporting footprint, signal-integrity, and replacement decisions.
Alternatif penggantian untuk SN74HC367D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
74HC367D,653
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
SN74HC367D Rating Maksimal & Karakteristik Listrik
| Number of Channels | 6 channels |
| Tegangan Pemuat Kerja | 2 V to 6 V |
| Logic Type | Non-inverting CMOS buffer and line driver |
| Output State | 3-state output |
| Output Bank Configuration | One 4-channel bank and one 2-channel bank |
| Output Enable Control | One independent enable for each output bank |
| High-Impedance Control | Enabled by a HIGH on the corresponding output-enable input |
| Arus Memerintah | 7.8 mA |
| Rentang Suhu Kerja | -40 °C to +85 °C |
| Paket | 16-pin SOIC |
| Tipe Mounting | Surface mount |
| Logic Level | CMOS |
| Output Bank Sizes | 4 outputs and 2 outputs |
| Signal Direction | Unidirectional |
| Voltage-Level Translation Function | Unidirectional |
| Status RoHS | Compliant |
Konfigurasi Pin SN74HC367D
| Pin produk 1 | 1A — Data input for output 1 |
| Pin produk 2 | 2A — Data input for output 2 |
| Pin produk 3 | GND — Ground |
| Pin produk 4 | 3A — Data input for output 3 |
| Pin produk 5 | 4A — Data input for output 4 |
| Pin produk 6 | 2Y — Buffer output 2 |
| Pin produk 7 | 1Y — Buffer output 1 |
| Pin produk 8 | 3Y — Buffer output 3 |
| Pin produk 9 | 4Y — Buffer output 4 |
| Pin produk 10 | 3OE — Output enable for the four-output bank |
| Pin produk 11 | 4OE — Output enable for the four-output bank |
| Pin produk 12 | 1OE — Output enable for the two-output bank |
| Pin produk 13 | 2OE — Output enable for the two-output bank |
| Pin produk 14 | VCC — Power supply |
| Pin produk 15 | 5A — Data input for output 5 |
| Pin produk 16 | 6A — Data input for output 6 |
Aplikasi Umum
SN74HC367D cocok untuk 6 aplikasis: Shared Digital Bus Isolation, Memory and Peripheral Interface, Data Acquisition Backplane, Digital Control Board, Bus Transceiver Support, Communication and Network Equipment.
Shared Digital Bus Isolation
The SN74HC367D fits shared-bus isolation because it provides six non-inverting three-state outputs over a 2 V to 6 V supply. According to the Texas Instruments manufacturer datasheet, the outputs are arranged as one four-channel bank and one two-channel bank, each with its own output-enable input. Placing the buffer near the bus allows a four-device group to be disconnected while two outputs remain active, or the reverse. Confirm propagation delay and bus transition requirements against the system timing, and add a pull-up or pull-down when a disabled bus must retain a defined voltage.
Direkomendasikan
Memory and Peripheral Interface
The SN74HC367D can buffer address, data, or peripheral-control lines on a 2 V to 6 V logic board. Its six non-inverting channels and two independent enable groups provide enough control granularity to isolate one interface section while maintaining another. According to the Texas Instruments manufacturer datasheet, a HIGH on an output-enable input places the associated bank in the high-impedance state. This is useful when several devices may contend for a bus, although the design must define the disabled-line state and verify timing margins at the intended voltage and load.
Direkomendasikan
Data Acquisition Backplane
The SN74HC367D is useful in data-acquisition backplanes where several instrument or digitizer boards can connect to a common control or data bus. Its six tri-state outputs provide active drive for the connected logic while allowing the four-channel and two-channel banks to be disabled independently. According to the Texas Instruments manufacturer datasheet, the device operates from 2 V to 6 V and offers non-inverting signal transmission. Layout should keep the shared traces away from enable inputs, and external bias resistors should maintain valid levels whenever all participating drivers enter the high-impedance state.
Direkomendasikan
Digital Control Board
A 5 V industrial or embedded control board can use the SN74HC367D to combine signal buffering, drive strength, and grouped high-impedance control. According to the Texas Instruments manufacturer datasheet, the device supports a 2 V to 6 V supply and contains six non-inverting channels with separate four-output and two-output enable banks. This arrangement simplifies routing when four connector or peripheral lines need to be released together. Engineers should verify output-current capability, input thresholds, propagation delay, and the state of every potentially floating bus during enable transitions.
Direkomendasikan
Bus Transceiver Support
The SN74HC367D can support the receive or drive side of a bus transceiver by providing non-inverting buffers with controllable high-impedance outputs. According to the Texas Instruments manufacturer datasheet, its independent four-channel and two-channel banks let a designer disable groups of external connections while keeping other interfaces operational. The device does not reverse signal direction, so it should be paired with direction-control logic when a bidirectional bus requires true transmit and receive switching. Validate setup and hold timing at the selected supply voltage and ensure that disabled outputs are externally biased when required.
Direkomendasikan
Communication and Network Equipment
The SN74HC367D fits communication equipment that requires several internal lines to connect and disconnect cleanly on a shared bus. Its six non-inverting, three-state channels operate from 2 V to 6 V and are divided into independently controlled banks, allowing one link group to be isolated without disabling the complete device. According to the Texas Instruments manufacturer datasheet, this two-bank organization is inherent to the SN74HC367 architecture. Place the component near the shared connector or backplane, keep enable traces quiet, and verify that loss of all drivers does not leave a control or status line at an undefined voltage.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk SN74HC367D — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | 74HC367D,653 |
|---|---|---|
| Package | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Nexperia |
| Number of Channels | 6 channels | 6 channels |
| Logic Polarity | Non-inverting | Non-inverting |
| Output Configuration | 3-state output | 3-state output |
| Output Bank Configuration | One 4-channel bank and one 2-channel bank | One 4-channel bank and one 2-channel bank |
Diferensiator Kunci
- Independent control of four-output and two-output banks (vs74HC367D,653)
- Six non-inverting channels in one 16-pin package (vs74HC367D,653)
- Wide 2 V to 6 V operating range (vs74HC367D,653)
Catatan Desain
Route the two output-enable inputs away from the six output nets and the shared bus. The enable signals control separate four-output and two-output banks, so crosstalk on either control line can release or disable an unintended group. Place the SN74HC367D close to the bus connector or transceiver, keep the ground return continuous, and follow the manufacturer input and output timing tables when evaluating propagation-delay margins.
A tri-state output does not retain a valid logic level while it is in the high-impedance state. If all devices connected to a bus can become disabled, add an external pull-up or pull-down sized for the bus capacitance, leakage, and required transition rate. Also connect every unused data input to VCC or GND according to the manufacturer logic requirements; do not leave an input floating.
Place input and output decoupling close to the device and preserve a low-impedance ground connection beneath the circuit. Avoid routing the shared bus beneath noisy clock, power-converter, or high-current return paths. Because the SN74HC367D has independent four-channel and two-channel enable banks, separate the associated connector or device groups logically on the board so enable transitions cannot unintentionally affect another subsystem.
The SN74HC367D operates from 2 V to 6 V, so verify that connected CMOS devices use compatible input thresholds and that all output voltages remain within their allowed ranges. Check high-level and low-level output current before driving several loads. The listed 7.8 mA quiescent current should be included in the system power budget, with additional load current added for every enabled channel and enabled external bus load.
Informasi Konformitas
RoHS compliance is identified in the component listing. REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information. AEC-Q100 qualification is not indicated for this commercial-temperature device.