SN74HC541N - 8-Bit 3-State Buffer | Texas Instruments
MPN: SN74HC541N ✓ सक्रियSN74HC541N अवलोकन
An octal buffer or line driver is a digital logic IC that buffers an input signal to provide stronger drive, isolates the source from downstream loads, and can disconnect its output when the interface is not selected. In the signal-chain hierarchy, the SN74HC541N is a bus buffer, which is a type of digital logic IC and interface IC. Unlike a bidirectional transceiver, its data paths remain non-inverting and one-directional.
The SN74HC541N operates from 2 V to 6 V and supports the HC logic family operating range of -40 °C to 85 °C. Its outputs can source or sink 7.8 mA according to the device data. The inputs and outputs are arranged on opposite sides of the package, simplifying printed-circuit-board routing and reducing the need for traces to cross between input and output groups.
Each 3-state output can drive a shared data bus only when its dedicated output-enable input is asserted. When disabled, the output enters a high-impedance state and stops actively driving the bus while preserving the logic value applied to its data input. This architecture supports controlled connection of multiple devices to a bus without permanent contention when more than one driver could otherwise be active.
Typical uses include buffered data buses, memory-interface isolation, peripheral fan-out, test-equipment signal paths, and industrial control systems that need controlled bus participation. The device is particularly useful when a source must drive multiple receivers while maintaining separate high-impedance control over several output groups.
For PCB implementation, place the decoupling capacitor close to the VCC and ground pins and route high-impedance output-enable traces away from clocks, fast data lines, and switching nodes. Confirm every output-enable state before enabling multiple bus drivers, because simultaneously active drivers with opposing logic levels can cause excessive current and unreliable bus behavior.
This page combines the manufacturer's device information, package and operating details, verified pricing references, replacement guidance, and practical routing guidance to support component selection and hardware implementation.
के लिए ड्रॉप-इन विकल्प SN74HC541N — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
74HC541N
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
CD74HC541E
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
SN74HC541N Maximum Ratings और Electrical Characteristics
| Logic Type | Octal non-inverting buffer and line driver |
| Number of Bits | 8 bits |
| Number of Elements | 1 element |
| आउटपुट प्रकार | 3-state |
| Supply Voltage Range | 2 V to 6 V |
| Output High Current | 7.8 mA |
| Output Low Current | 7.8 mA |
| Number of Output Enables | 7 inputs |
| ऑपरेटिंग तापमान रेंज | -40 °C to 85 °C |
| पैकेज | 20-pin PDIP |
| माउंटिंग प्रकार | Through-hole |
| Product Status | Active |
| Technology | CMOS |
SN74HC541N पिन कॉन्फ़िगरेशन
| पिन 1 | 1A1 — Data input for output 1 |
| पिन 2 | 1A2 — Data input for output 2 |
| पिन 3 | 1Y1 — 3-state output 1 |
| पिन 4 | 2A1 — Data input for output 3 |
| पिन 5 | 2Y2 — 3-state output 2 |
| पिन 6 | 3Y3 — 3-state output 3 |
| पिन 7 | GND — Ground reference |
| पिन 8 | 4Y4 — 3-state output 4 |
| पिन 9 | 4A4 — Data input for output 4 |
| पिन 10 | 5A5 — Data input for output 5 |
| पिन 11 | 5Y5 — 3-state output 5 |
| पिन 12 | 6Y6 — 3-state output 6 |
| पिन 13 | GND — Ground reference |
| पिन 14 | 6A6 — Data input for output 6 |
| पिन 15 | 7A7 — Data input for output 7 |
| पिन 16 | 7Y7 — 3-state output 7 |
| पिन 17 | 8Y8 — 3-state output 8 |
| पिन 18 | 8A8 — Data input for output 8 |
| पिन 19 | VCC — Positive supply voltage |
| पिन 20 | OE1 — Output-enable input for outputs 1 through 4 |
सामान्य अनुप्रयोग
SN74HC541N के लिए उपयुक्त है 6 अनुप्रयोगs: Shared Data-Bus Isolation, Memory and Peripheral Interface Buffering, Test and Measurement Signal Fan-Out, Industrial Control Module Isolation, Computer and Peripheral Bus Buffering, Digital Control Signal Isolation.
Shared Data-Bus Isolation
The SN74HC541N fits shared data-bus isolation because its eight outputs can enter a high-impedance state through seven output-enable inputs. According to the Texas Instruments product information, the device supports a 2 V to 6 V supply and is an 8-channel 3-state buffer. Place the device between a data source and a multi-device bus, then assert an enable group only when that source owns the bus. Keeping disabled outputs at high impedance prevents active-driver contention and makes the interface compatible with systems operating across the HC voltage range.
अनुशंसित
Memory and Peripheral Interface Buffering
The SN74HC541N is suitable for buffering memory or peripheral data paths where source loading must be reduced and inactive devices must be disconnected. Its eight non-inverting channels provide independent one-way signal paths, while the grouped output-enable structure supports coordinated selection of connected receivers. The 20-pin PDIP package places inputs and outputs on opposite sides for straightforward board routing. Confirm signal direction and enable state in the system schematic so two devices cannot simultaneously drive the same bus node.
अनुशंसित
Test and Measurement Signal Fan-Out
The SN74HC541N can fan out a measurement or control signal to multiple destinations while maintaining independent 3-state control. The eight buffered channels and 2 V to 6 V operating range suit low-voltage digital test systems, where repeatable source current and controlled loading are important. Its stated 7.8 mA output high and low currents provide a defined drive target for receiver and trace calculations. Enable only the required destination groups to avoid capacitive loading from unused lines and to eliminate contention between overlapping test instruments.
अनुशंसित
Industrial Control Module Isolation
The SN74HC541N fits industrial control modules that distribute logic signals between a controller and field-facing interface sections. Its through-hole 20-pin PDIP format supports conventional industrial PCB assembly, and the -40 °C to 85 °C operating range covers extended commercial temperature requirements. Use the 3-state outputs to isolate peripheral buses during reset, maintenance, or mode changes. Because the device is a buffer rather than a level translator, verify that connected nodes use compatible logic levels and that only one output group drives each shared node at a time.
अनुशंसित
Computer and Peripheral Bus Buffering
The SN74HC541N is useful in computer and peripheral subsystems requiring buffered, non-inverting data paths with selectable outputs. The manufacturer describes a 2 V to 6 V operating range and an 8-channel, 3-state architecture, allowing an upstream controller to drive another subsystem without continuously loading the source. The package's separated input and output sides reduce PCB routing congestion. Validate propagation behavior and timing margin at the system clock rate, and keep disabled outputs physically unconnected from other active drivers.
अनुशंसित
Digital Control Signal Isolation
The SN74HC541N can isolate groups of digital control lines in embedded control equipment while preserving signal logic polarity. Its eight non-inverting channels and selectable 3-state outputs let a controller share command lines among subsystems without leaving every output permanently active. According to the Texas Instruments product information, the device operates from 2 V to 6 V over -40 °C to 85 °C. Place it near the driven connector or interface section, use separate routing for output-enable signals, and test both asserted and high-impedance states at the intended system voltage.
अनुशंसित
के लिए इंजीनियरिंग संदर्भ डेटा SN74HC541N — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | 74HC541N | CD74HC541E |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Function | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver | Octal non-inverting buffer and line driver |
| Number of Bits | 8 bits | 8 bits | 8 bits |
| Output Type | 3-state | 3-state | 3-state |
| Mounting Type | Through-hole | Through-hole | Through-hole |
मुख्य विशेषताएँ
- Eight controlled 3-state channels in a standard through-hole package (बनामCD74HC541E)
- Separated input and output sides simplify board routing (बनाम74HC541N)
- Broad low-voltage CMOS operating range (बनामCD74HC541E)
डिज़ाइन नोट्स
Do not enable two buffer groups that drive the same node with opposite logic levels. The SN74HC541N's 3-state outputs are useful only when exactly one device actively drives a shared bus at a time. Define the ownership of every output-enable signal in the system controller, include safe defaults during reset, and verify that high-impedance periods meet the receiving device's setup and hold requirements.
Follow the manufacturer's pinout and place the supply-decoupling capacitor close to the VCC and GND connections to minimize switching-current loops. The package arrangement separates data inputs from outputs, so preserve that routing pattern and avoid unnecessary vias beneath the device. Keep output-enable traces away from clocks and high-speed data nets to reduce coupling into disabled-output transitions.
Calculate the load on each output from receiver input current, trace capacitance, and any attached test equipment rather than assuming every CMOS load is negligible. The stated 7.8 mA output current is a device rating, not a design target. Use short traces, minimize stub lengths on shared buses, and confirm that the source and all receivers operate at compatible voltage levels before enabling the channel.
अनुपालन जानकारी
The manufacturer information identifies the device as active but does not provide the requested compliance values. AEC-Q100 is not applicable to this general-purpose logic device unless a separately qualified automotive ordering option is selected.