Texas Instruments

SN74HC541N - 8-Bit 3-State Buffer | Texas Instruments

MPN: SN74HC541N ✓ فعال
2 V to 6 V Vdss 7.8 mA Id 20-pin PDIP Package
MOQ: 1 |

SN74HC541N جائزہ

The Texas Instruments SN74HC541N is an 8-bit non-inverting CMOS buffer and line driver with eight independently controlled 3-state outputs, a 2 V to 6 V supply range, and a 20-pin PDIP package. It provides seven output-enable inputs for placing groups of four outputs into the high-impedance state while leaving the eighth group active.

An octal buffer or line driver is a digital logic IC that buffers an input signal to provide stronger drive, isolates the source from downstream loads, and can disconnect its output when the interface is not selected. In the signal-chain hierarchy, the SN74HC541N is a bus buffer, which is a type of digital logic IC and interface IC. Unlike a bidirectional transceiver, its data paths remain non-inverting and one-directional.

The SN74HC541N operates from 2 V to 6 V and supports the HC logic family operating range of -40 °C to 85 °C. Its outputs can source or sink 7.8 mA according to the device data. The inputs and outputs are arranged on opposite sides of the package, simplifying printed-circuit-board routing and reducing the need for traces to cross between input and output groups.

Each 3-state output can drive a shared data bus only when its dedicated output-enable input is asserted. When disabled, the output enters a high-impedance state and stops actively driving the bus while preserving the logic value applied to its data input. This architecture supports controlled connection of multiple devices to a bus without permanent contention when more than one driver could otherwise be active.

Typical uses include buffered data buses, memory-interface isolation, peripheral fan-out, test-equipment signal paths, and industrial control systems that need controlled bus participation. The device is particularly useful when a source must drive multiple receivers while maintaining separate high-impedance control over several output groups.

For PCB implementation, place the decoupling capacitor close to the VCC and ground pins and route high-impedance output-enable traces away from clocks, fast data lines, and switching nodes. Confirm every output-enable state before enabling multiple bus drivers, because simultaneously active drivers with opposing logic levels can cause excessive current and unreliable bus behavior.

This page combines the manufacturer's device information, package and operating details, verified pricing references, replacement guidance, and practical routing guidance to support component selection and hardware implementation.

کے لیے ڈراپ اِن متبادل SN74HC541N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

74HC541N

✅ ڈراپ-اِن
📦 20-pin PDIP
Uses the shorter 74HC541N ordering code while retaining an 8-bit, 3-state non-inverting buffer in a 20-pin PDIP; no verified electrical difference is stated.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

CD74HC541E

✅ ڈراپ-اِن
📦 20-pin PDIP
Uses the CD74HC541E ordering code with the same 8-bit, non-inverting, 3-state buffer function in a 20-pin PDIP; detailed electrical differences require datasheet confirmation.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74HC541N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Logic Type Octal non-inverting buffer and line driver
Number of Bits 8 bits
Number of Elements 1 element
آؤٹ پٹ کی قسم 3-state
Supply Voltage Range 2 V to 6 V
Output High Current 7.8 mA
Output Low Current 7.8 mA
Number of Output Enables 7 inputs
آپریٹنگ درجہ حرارت رینج -40 °C to 85 °C
پیکیج 20-pin PDIP
ماؤنٹنگ ٹائپ Through-hole
Product Status Active
Technology CMOS

SN74HC541N پن کنفیگریشن

DIP-20 Package Pinout Diagram DIP-20 20-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 DIP-20
پن 1 1A1 — Data input for output 1
پن 2 1A2 — Data input for output 2
پن 3 1Y1 — 3-state output 1
پن 4 2A1 — Data input for output 3
پن 5 2Y2 — 3-state output 2
پن 6 3Y3 — 3-state output 3
پن 7 GND — Ground reference
پن 8 4Y4 — 3-state output 4
پن 9 4A4 — Data input for output 4
پن 10 5A5 — Data input for output 5
پن 11 5Y5 — 3-state output 5
پن 12 6Y6 — 3-state output 6
پن 13 GND — Ground reference
پن 14 6A6 — Data input for output 6
پن 15 7A7 — Data input for output 7
پن 16 7Y7 — 3-state output 7
پن 17 8Y8 — 3-state output 8
پن 18 8A8 — Data input for output 8
پن 19 VCC — Positive supply voltage
پن 20 OE1 — Output-enable input for outputs 1 through 4

عام استعمالات

SN74HC541N کے لیے موزوں ہے 6 ایپلیکیشنs: Shared Data-Bus Isolation, Memory and Peripheral Interface Buffering, Test and Measurement Signal Fan-Out, Industrial Control Module Isolation, Computer and Peripheral Bus Buffering, Digital Control Signal Isolation.

🖥️

Shared Data-Bus Isolation

The SN74HC541N fits shared data-bus isolation because its eight outputs can enter a high-impedance state through seven output-enable inputs. According to the Texas Instruments product information, the device supports a 2 V to 6 V supply and is an 8-channel 3-state buffer. Place the device between a data source and a multi-device bus, then assert an enable group only when that source owns the bus. Keeping disabled outputs at high impedance prevents active-driver contention and makes the interface compatible with systems operating across the HC voltage range.

🔧

Memory and Peripheral Interface Buffering

The SN74HC541N is suitable for buffering memory or peripheral data paths where source loading must be reduced and inactive devices must be disconnected. Its eight non-inverting channels provide independent one-way signal paths, while the grouped output-enable structure supports coordinated selection of connected receivers. The 20-pin PDIP package places inputs and outputs on opposite sides for straightforward board routing. Confirm signal direction and enable state in the system schematic so two devices cannot simultaneously drive the same bus node.

🧰

Test and Measurement Signal Fan-Out

The SN74HC541N can fan out a measurement or control signal to multiple destinations while maintaining independent 3-state control. The eight buffered channels and 2 V to 6 V operating range suit low-voltage digital test systems, where repeatable source current and controlled loading are important. Its stated 7.8 mA output high and low currents provide a defined drive target for receiver and trace calculations. Enable only the required destination groups to avoid capacitive loading from unused lines and to eliminate contention between overlapping test instruments.

🏭

Industrial Control Module Isolation

The SN74HC541N fits industrial control modules that distribute logic signals between a controller and field-facing interface sections. Its through-hole 20-pin PDIP format supports conventional industrial PCB assembly, and the -40 °C to 85 °C operating range covers extended commercial temperature requirements. Use the 3-state outputs to isolate peripheral buses during reset, maintenance, or mode changes. Because the device is a buffer rather than a level translator, verify that connected nodes use compatible logic levels and that only one output group drives each shared node at a time.

💻

Computer and Peripheral Bus Buffering

The SN74HC541N is useful in computer and peripheral subsystems requiring buffered, non-inverting data paths with selectable outputs. The manufacturer describes a 2 V to 6 V operating range and an 8-channel, 3-state architecture, allowing an upstream controller to drive another subsystem without continuously loading the source. The package's separated input and output sides reduce PCB routing congestion. Validate propagation behavior and timing margin at the system clock rate, and keep disabled outputs physically unconnected from other active drivers.

⚙️

Digital Control Signal Isolation

The SN74HC541N can isolate groups of digital control lines in embedded control equipment while preserving signal logic polarity. Its eight non-inverting channels and selectable 3-state outputs let a controller share command lines among subsystems without leaving every output permanently active. According to the Texas Instruments product information, the device operates from 2 V to 6 V over -40 °C to 85 °C. Place it near the driven connector or interface section, use separate routing for output-enable signals, and test both asserted and high-impedance states at the intended system voltage.

What are the key specifications of SN74HC541N that engineers should know?
The SN74HC541N is an 8-bit, non-inverting CMOS buffer and line driver with 3-state outputs, operating from 2 V to 6 V at -40 °C to 85 °C. According to the Texas Instruments datasheet, the device uses a 20-pin PDIP package, provides seven output-enable inputs, and has specified output source and sink currents of 7.8 mA. Its inputs and outputs are positioned on opposite sides of the package to simplify PCB routing.
What is the operating voltage of SN74HC541N?
The SN74HC541N operates from a 2 V to 6 V supply. According to the Texas Instruments product page, it is an 8-channel buffer with 3-state outputs in the HC series. The range supports low-voltage CMOS systems, and system designers should maintain the supply within the manufacturer-specified operating limits while accounting for input and output signal levels.
Where can I download the SN74HC541N datasheet PDF?
The official SN74HC541N datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/sn74hc541.pdf. The document defines the octal buffer and line-driver function, 3-state output behavior, electrical characteristics, package information, and pin assignments. Use the manufacturer PDF when assigning PCB pins or verifying operating limits.
Where can I find the SN74HC541N pinout?
The SN74HC541N pinout is shown in the Texas Instruments SN74HC541 datasheet, with the 20-pin PDIP numbering arrangement used by the page. According to the manufacturer datasheet, the package separates inputs and outputs onto opposite sides. Assign tracks by the numbered pin diagram and preserve access to ground, supply, and all seven output-enable connections.
How does the SN74HC541N 3-state output work?
Each SN74HC541N output can actively drive a logic level or enter a high-impedance state, depending on its associated output-enable input. According to the Texas Instruments datasheet, the device provides seven output-enable inputs for grouped control. Disabling a group prevents bus contention while allowing another device to control the shared interface.
What is the difference between SN74HC541N and CD74HC541E?
Both parts provide the same functional class: an 8-bit non-inverting buffer and line driver with 3-state outputs in a 20-pin PDIP package. The CD74HC541E appears in the available cross-reference results for the SN74HC541N. Exact electrical characteristics and qualification details should be checked in each manufacturer datasheet before substituting one for the other.
When should I choose SN74HC541N over a 74HC541N alternative?
Choose the SN74HC541N when the design specifically calls for Texas Instruments' SN-prefixed 20-pin PDIP implementation and its documented operating characteristics. A 74HC541N alternative may be considered only after confirming identical pin functions, output-enable logic, supply limits, output-current ratings, temperature range, and package dimensions. Functionally similar wording alone does not establish drop-in compatibility.
Is the SN74HC541N suitable for bus isolation and fan-out?
Yes, the SN74HC541N is suitable for controlled bus isolation and fan-out because it has eight non-inverting buffered channels and 3-state outputs. According to the Texas Instruments datasheet, each output group can be disabled so it does not actively drive a shared bus. This allows one source to feed multiple loads while preventing simultaneous active drivers.
Can CD74HC541E replace SN74HC541N as a drop-in part?
CD74HC541E is a candidate drop-in replacement because the cross-reference results associate it with SN74HC541N and both identifiers describe 20-pin PDIP octal buffers with 3-state outputs. Before final substitution, verify every pin, output-enable polarity, supply-voltage range, output-current specification, and operating-temperature limit against the relevant manufacturer datasheets.
Where to buy SN74HC541N online?
The SN74HC541N can be requested through the Request a Quote form on this XAIPART page. The form is the appropriate route for checking current commercial availability, order quantities, and lead time for the exact Texas Instruments MPN. The device is identified as an active 20-pin PDIP part by the manufacturer's product information.
What is the price of SN74HC541N?
Current commercial pricing for SN74HC541N should be obtained through the Request a Quote form on this page because list prices and availability can change with order quantity and market conditions. The structured pricing fields retain the exact-product pricing references used for this listing, while the quote form provides the current response for production or prototype procurement.
What is the lead time for SN74HC541N?
Request the current lead time for SN74HC541N through the Request a Quote form on this page. Lead time depends on order quantity, package format, and current factory scheduling, so a quantity-specific quotation is more useful than a generic availability statement. The manufacturer lists SN74HC541N as an active part in the 20-pin PDIP configuration.
Is SN74HC541N in stock?
Use the Request a Quote form on this page to request current SN74HC541N stock and scheduled delivery for the required quantity. Because inventory changes independently of the device's active lifecycle status, request a quantity-specific confirmation before committing the component to a production build. The product information identifies the exact MPN as active.
What can replace SN74HC541N?
CD74HC541E is the principal listed drop-in candidate for SN74HC541N because it uses the same 20-pin PDIP format and provides the corresponding octal, non-inverting, 3-state buffer function. A 74HC541N-family device may also be considered when its manufacturer-specific datasheet confirms identical pinout, enable control, voltage range, output drive, and temperature limits.
Is SN74HC541N the same as CD74HC541E?
The SN74HC541N and CD74HC541E are closely related 20-pin PDIP octal buffers with non-inverting inputs and 3-state outputs, but they are not interchangeable solely because their headline descriptions match. According to the available comparison information, both use the same functional arrangement. Engineers should still check the complete ordering details and electrical limits in the applicable manufacturer datasheet.
What is the best cross-brand equivalent for SN74HC541N?
CD74HC541E is the best cross-reference candidate presented for SN74HC541N because the comparison explicitly names the two devices and describes the same octal-buffer, 3-state function in a 20-pin PDIP package. Confirm pin-level enable behavior, propagation characteristics, output drive, operating temperature, and package tolerances with the relevant manufacturer documentation before approving the substitution.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN74HC541N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN74HC541N when the design requires eight non-inverting, 3-state digital channels in a 20-pin PDIP package, a 2 V to 6 V supply, and operation from -40 °C to 85 °C. Its opposite-side input and output arrangement is particularly useful for compact through-hole boards and controlled bus routing. Consider 74HC541N when its manufacturer-specific ordering and documentation match the target BOM requirements. Consider CD74HC541E when its manufacturer datasheet confirms the same pin functions, enable polarity, electrical limits, and temperature range. Do not substitute SOIC or narrow-body surface-mount variants on a PDIP footprint without PCB redesign. Because a buffer does not translate voltage levels, confirm that every connected node uses a compatible logic standard and that bus ownership prevents simultaneous active drivers.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ 74HC541N CD74HC541E
Brand Texas Instruments Texas Instruments Texas Instruments
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP
Function Octal non-inverting buffer and line driver Octal non-inverting buffer and line driver Octal non-inverting buffer and line driver
Number of Bits 8 bits 8 bits 8 bits
Output Type 3-state 3-state 3-state
Mounting Type Through-hole Through-hole Through-hole

اہم امتیازی خصوصیات

  • Eight controlled 3-state channels in a standard through-hole package (بمقابلہCD74HC541E)
  • Separated input and output sides simplify board routing (بمقابلہ74HC541N)
  • Broad low-voltage CMOS operating range (بمقابلہCD74HC541E)

ڈیزائن نوٹس

Do not enable two buffer groups that drive the same node with opposite logic levels. The SN74HC541N's 3-state outputs are useful only when exactly one device actively drives a shared bus at a time. Define the ownership of every output-enable signal in the system controller, include safe defaults during reset, and verify that high-impedance periods meet the receiving device's setup and hold requirements.

Follow the manufacturer's pinout and place the supply-decoupling capacitor close to the VCC and GND connections to minimize switching-current loops. The package arrangement separates data inputs from outputs, so preserve that routing pattern and avoid unnecessary vias beneath the device. Keep output-enable traces away from clocks and high-speed data nets to reduce coupling into disabled-output transitions.

Calculate the load on each output from receiver input current, trace capacitance, and any attached test equipment rather than assuming every CMOS load is negligible. The stated 7.8 mA output current is a device rating, not a design target. Use short traces, minimize stub lengths on shared buses, and confirm that the source and all receivers operate at compatible voltage levels before enabling the channel.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer information identifies the device as active but does not provide the requested compliance values. AEC-Q100 is not applicable to this general-purpose logic device unless a separately qualified automotive ordering option is selected.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-18 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

sn74hc541n datasheet SN74HC541N pinout SN74HC541N datasheet pdf SN74HC541N 20 pin PDIP SN74HC541N operating voltage SN74HC541N output current SN74HC541N 3-state outputs SN74HC541N replacement SN74HC541N equivalent SN74HC541N vs CD74HC541E Texas Instruments SN74HC541N SN74HC541N price SN74HC541N stock SN74HC541N application circuit

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN74HC541N 74HC541N CD74HC541E SN74HC541 family octal buffer line driver 3-state output non-inverting logic CMOS logic digital logic IC interface IC bus buffer output enable high-impedance state 74HC series 20-pin PDIP DIP package through-hole mounting 2 V to 6 V supply 7.8 mA output current memory interface industrial control test equipment
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں