SN74LS243D - 4-Bit Bus Transceiver | Texas Instruments
MPN: SN74LS243D ✓ सक्रियSN74LS243D अवलोकन
A bus transceiver is an interface circuit that allows data to move in either direction between a host logic system and an external bus. The quad designation indicates four independently controlled transceiver elements, while the 4-bit designation identifies the parallel data width associated with those elements. Together, these features place the SN74LS243D in the logic IC > interface IC > bus transceiver hierarchy.
The SN74LS243D combines four bidirectional transceiver elements with non-inverting push-pull outputs. According to the Texas Instruments product page, the SN74LS243 family can drive terminated lines down to 133 ohms. The SN74LS243 commercial-temperature version is characterized for operation from 0°C to 70°C. Its SOIC-14 package supports conventional surface-mount PCB assembly.
The device is intended for asynchronous two-way bus communication, allowing each associated data path to operate as an input or output. Its push-pull output structure is appropriate for digital systems that require defined output levels and balanced drive capability. Because the communication path is bidirectional, system designers must control the transceiver direction through associated interface logic and account for signal timing at both ends of the bus.
Typical uses include instrumentation buses, computer peripherals, industrial data exchange, test equipment, and embedded control systems. The 14-pin package simplifies routing compared with larger 8-bit bus transceivers, while the four-element arrangement can cover four data paths when the full bus width is not required. The same organization can also be used in bidirectional buffering arrangements where a host processor communicates with a peripheral over shared conductors.
When laying out a board, keep the transceiver near the connector or bus interface, provide a low-impedance ground plane, and place input and output decoupling capacitors close to the supply pins. Check the datasheet pin-description table for the exact direction-control and data-pin assignments before assigning PCB tracks. The 133-ohm line requirement also means that cable or board transmission-line characteristics must be considered rather than treating every connection as an ideal point-to-point link.
This product page organizes the manufacturer specifications, source documents, procurement path, and practical replacement considerations into one engineering reference. It also highlights where a design can reuse the 14-SOIC footprint and where a full pin-by-pin comparison remains necessary before substituting a part from another supplier.
के लिए ड्रॉप-इन विकल्प SN74LS243D — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
SN74LS243D
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →SN74LS243D
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →SN74LS243D विशेषताएं
| Product Type | Quad 4-bit bus transceiver |
| Number of Elements | 4 transceivers |
| Bits per Element | 4 bits |
| Logic Polarity | Non-inverting |
| आउटपुट प्रकार | Push-pull |
| Communication Mode | Asynchronous, two-way |
| सप्लाई वोल्टेज | 5 V |
| Minimum Terminated Line Load | 133 ohms |
| Commercial Operating Temperature | 0°C to 70°C |
| Military Operating Temperature Reference | -55°C to 125°C for SN54LS243 |
| पैकेज | 14-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Packaging Form | Tube |
SN74LS243D 14-pin soic पिन कॉन्फ़िगरेशन गाइड
SN74LS243D (14-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: SN74LS243D.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
SN74LS243D के लिए उपयुक्त है 6 अनुप्रयोगs: Asynchronous Instrument Bus Interface, Embedded Controller Peripheral Bus, Computer Peripheral Data Port, Industrial Control Data Exchange, Test and Measurement Equipment, General-Purpose Logic Data Link.
Asynchronous Instrument Bus Interface
The SN74LS243D fits an asynchronous two-way bus between an instrument controller and a peripheral because it combines four 4-bit transceiver elements with non-inverting push-pull outputs. According to the Texas Instruments product page, the family supports terminated lines down to 133 ohms. Place the device between the controller’s data lines and the bus connector, then use the associated direction and enable controls to prevent opposing drivers from operating simultaneously. The 5 V supply arrangement supports LS-family logic, while the 14-SOIC package keeps the interface compact enough for instrumentation and test equipment. Timing across the two bus directions should be checked against the peripheral’s turnaround requirements.
अनुशंसित
Embedded Controller Peripheral Bus
The SN74LS243D can connect a small controller subsystem to a peripheral board when four related data paths are sufficient for the required bus width. Its four transceiver elements, each described as 4-bit per element, provide a compact bidirectional interface rather than requiring four separate single-channel devices. The non-inverting push-pull output supports deterministic 5 V LS logic signaling, and the manufacturer identifies the family for asynchronous two-way communication. Direction-control sequencing is the primary design consideration: the controller must ensure that only one side drives each shared path at a time.
अनुशंसित
Computer Peripheral Data Port
The SN74LS243D is appropriate for a legacy peripheral port that needs a compact bidirectional interface between a host bus and external logic. Four transceiver elements in one 14-SOIC package reduce the component count compared with separate buffers, while non-inverting push-pull operation preserves the positive logic polarity of LS TTL signals. The Texas Instruments product page states that the family can drive terminated lines down to 133 ohms, making line termination an explicit part of the interface design. A peripheral implementation should also observe setup and hold requirements around direction changes to avoid bus contention.
अनुशंसित
Industrial Control Data Exchange
The SN74LS243D can support short-distance asynchronous data exchange between an industrial controller card and a remote I/O module when the ambient environment stays within the commercial 0°C to 70°C range. Its four-element bidirectional organization is useful for separating the controller from a bus connector and for improving interface drive behavior. The manufacturer identifies the SN74LS243 as a 5 V device capable of driving terminated lines down to 133 ohms. In an industrial enclosure, solid grounding, connector shielding, and controlled direction sequencing are important, while any wider-temperature requirement calls for a suitably characterized device.
अनुशंसित
Test and Measurement Equipment
The SN74LS243D is useful in test and measurement equipment that exchanges control and status data with an external fixture or instrument. The four-element arrangement can consolidate multiple bidirectional links, and the 14-SOIC package supports conventional surface-mount routing. According to the Texas Instruments product page, the circuit is intended for asynchronous two-way bus communications and terminated lines down to 133 ohms. Place the device near the fixture connector to minimize trace exposure, provide local supply bypassing, and use the data sheet timing information when sequencing control and measurement commands.
अनुशंसित
General-Purpose Logic Data Link
The SN74LS243D can be used as a general-purpose bidirectional logic data link when a system needs more than one non-inverting transceiver element but does not require a full-width 8-bit bus device. Its 5 V operation, 4-bit element organization, and push-pull outputs fit classic LS-family interface arrangements. The implementation should provide defined enable and direction states before data is transmitted, and it should avoid driving two push-pull outputs onto the same conductor simultaneously. Using a continuous ground plane and positioning the transceiver close to the interface connector will help maintain signal integrity on the asynchronous bus.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा SN74LS243D — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | SN74LS243D | SN74LS243D |
|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | NXP Semiconductors | Motorola |
| Product Type | Quad bus transceiver | Bus transceiver | Bus transceiver |
| Number of Elements | 4 transceivers | 4 transceivers | 4 transceivers |
| Bits per Element | 4 bits | 4 bits | 4 bits |
| Supply Voltage | 5 V | 5 V | 5 V |
| Communication Mode | Asynchronous, two-way | Asynchronous, two-way | Asynchronous, two-way |
| Minimum Terminated Line Load | 133 ohms | 133 ohms | 133 ohms |
मुख्य विशेषताएँ
- Combines four bidirectional transceiver elements in one 14-SOIC device (बनामSN74LS243N)
- Supports terminated asynchronous bus lines down to 133 ohms (बनामSN74LS244D)
- Non-inverting push-pull interface preserves positive LS logic polarity (बनामSN74LS240D)
डिज़ाइन नोट्स
Confirm the direction and enable truth table before assigning control pins. Bidirectional push-pull transceivers can create a direct output conflict if two sides drive the same bus conductor at the same time. Use external control logic or a defined controller state machine to guarantee a transition through the high-impedance or disabled state before the opposite side becomes active.
Place the SN74LS243D close to the bus connector or cable interface and provide a continuous ground reference beneath the device and connected bus traces. Keep supply-decoupling components near the power and ground connections and avoid routing sensitive signals beneath or parallel to long high-current return paths. The exact pin assignments should be taken from the manufacturer pin-description table before finalizing the layout.
The manufacturer identifies capability for terminated lines down to 133 ohms, so the PCB or cable network must use a compatible termination strategy. Account for driver strength, trace and connector loss, stub length, and the propagation delay of the selected transceiver. Avoid simultaneous data transitions on adjacent parallel lines when skew could violate setup and hold requirements at the receiving endpoint.
अनुपालन जानकारी
Compliance declarations were not identified in the available manufacturer product-page and distributor excerpts. Verify the current material, environmental, and quality declarations for the selected manufacturer ordering code before production release.