SY89809LTH - 2:9 500 MHz Clock Fanout Buffer | Microchip
MPN: SY89809LTH ✓ सक्रियSY89809LTH अवलोकन
A clock fanout buffer is a clock-management semiconductor that reproduces an incoming periodic signal across multiple outputs. Clock buffers and drivers sit within the clock and timing hierarchy, where they complement oscillators, phase-locked loops, dividers, and multiplexers. Their principal design roles are to restore signal integrity, provide output drive, isolate destinations, and maintain predictable timing relationships across a board or backplane.
The SY89809LTH supports a maximum operating frequency of 500 MHz. Its input interface accepts both LVPECL and HSTL signals, allowing compatibility with several common high-speed clocking conventions. The output stage provides nine differential HSTL pairs, while the documented output configuration is capable of driving 50 ohms to ground without an offset voltage. These characteristics make the device applicable to demanding clock-distribution trees rather than low-frequency general-purpose buffering.
Timing performance is a central consideration for this device. The Micrel manufacturer datasheet specifies a maximum part-to-part skew of 200 ps and a maximum pin-to-pin skew of 50 ps. Pin-to-pin skew describes variation between outputs of the same device, while part-to-part skew covers variation between different devices. These limits are particularly important when clocked logic must maintain source-synchronous relationships or when downstream receivers operate with limited timing margins.
Typical uses include high-speed server and storage interfaces, network-switch backplanes, telecommunications equipment, test-and-measurement systems, and other multi-drop clocking architectures. The device can also support clock muxing and distribution where two input sources must feed nine output locations. System designers should preserve controlled impedance and adequate return paths between the driver and each receiver to maintain the intended signal quality.
The principal design trade-off is operating speed versus integration and termination complexity. A 500 MHz differential HSTL clock network requires careful PCB stack-up, impedance control, termination, and clock-tree topology. The SY89809LTH provides nine differential outputs in one package, reducing the number of separate fanout stages needed for a wide distribution network.
This page consolidates the device's clock topology, frequency, interface, skew, package, and sourcing characteristics, then adds application guidance and verified-source links. It also distinguishes the LTH tray designation from other ordering options and explains what an engineer should confirm before treating another device as a drop-in replacement.
के लिए ड्रॉप-इन विकल्प SY89809LTH — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
SY89809LTH-TR
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
SY89809LTH विशेषताएं
| Product Type | Clock fanout buffer and multiplexer IC |
| Fanout Ratio | 2:9 |
| अधिकतम क्लॉक फ़्रीक्वेंसी | 500 MHz |
| Number of Inputs | 2 inputs |
| आउटपुट की संख्या | 9 differential output pairs |
| Supported Input Logic | LVPECL and HSTL |
| Output Logic | Differential HSTL |
| Nominal Supply Voltage | 3.3 V |
| Output Impedance | 50 ohm to ground |
| Output DC Offset | 0 V |
| Maximum Part-to-Part Skew | 200 ps |
| Maximum Pin-to-Pin Skew | 50 ps |
| पैकेज | 32-pin TQFP |
SY89809LTH 32-pin tqfp पिन कॉन्फ़िगरेशन गाइड
SY89809LTH (32-pin tqfp पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: SY89809LTH.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
SY89809LTH के लिए उपयुक्त है 6 अनुप्रयोगs: Server Platform Clock Distribution, Network Switch Backplane Clocking, Telecommunications Equipment Clock Fanout, Storage Controller Clock Distribution, Test and Measurement Clocking, Industrial Data Acquisition Systems.
Server Platform Clock Distribution
The SY89809LTH fits server clock trees that distribute a common source to multiple processor, memory, interface, or fabric clock domains below the 500 MHz device rating. Two selectable inputs support clock multiplexing, while nine differential HSTL output pairs provide substantial fanout without requiring a chain of small buffers. The 50 ps maximum pin-to-pin skew gives circuit designers a defined relationship among outputs from one device. In practice, the design must use controlled-impedance routing, suitable return paths, and receiver-appropriate termination. The low-voltage differential outputs also reduce noise sensitivity compared with single-ended distribution, although connector and package transitions must remain included in the channel-budget analysis.
अनुशंसित
Network Switch Backplane Clocking
The SY89809LTH is suitable for network-switch backplanes where a low-jitter reference clock must reach multiple line cards, ports, or internal processing blocks. Its two-input multiplexing capability can support source selection or redundancy control, and nine differential HSTL pairs provide enough outputs for a broad distribution tree. The device's 500 MHz maximum clock frequency accommodates high-speed digital architectures, while the 50 ps maximum pin-to-pin skew helps preserve alignment between related clock domains. Backplane implementation should account for connector loss, return discontinuities, and impedance transitions, because the IC cannot compensate for an uncontrolled transmission-line environment after the signal leaves its outputs.
अनुशंसित
Telecommunications Equipment Clock Fanout
The SY89809LTH can distribute a 500 MHz-or-lower system clock across multiple telecommunications processing sections when low-voltage differential signaling is appropriate. Nine output pairs allow a central source to feed several converters, interface engines, or fabric blocks while keeping the clock topology manageable. LVPECL and HSTL input support makes the device adaptable to common high-speed clock-generation chains. Because part-to-part skew is specified up to 200 ps, system timing analysis should distinguish outputs from the same package from clocks originating in different devices. Controlled PCB impedance and short return paths remain essential for preserving edge quality across cabinet-scale equipment.
अनुशंसित
Storage Controller Clock Distribution
The SY89809LTH can provide a multi-output clock source for storage controllers, NAND-interface logic, memory controllers, and associated data-path circuitry. Its 2:9 architecture permits one of two clocks to be selected and distributed across as many as nine differential outputs, reducing the number of separate clock-driver stages required in a dense board. At frequencies below 500 MHz, the device supplies useful integration while maintaining specified pin-to-pin and part-to-part skew limits. Layout should keep the clock distribution symmetric where possible, provide uninterrupted reference planes, and avoid stubs that could create reflections. Validate the complete clock path with the actual receiver loads and enclosure transitions.
अनुशंसित
Test and Measurement Clocking
The SY89809LTH is appropriate for test-and-measurement systems that must distribute a precise high-speed trigger, reference, or sampling clock among multiple instruments or acquisition channels. Two input selection and nine differential outputs allow a compact front end to support multiple instruments without creating a long chain of cascaded fanout devices. The 50 ps maximum pin-to-pin skew provides a useful measure of coherence among outputs from the same package. Designers should account for cable and connector losses, use appropriate differential terminations, and keep the clock source and distribution paths separated from noisy switching nodes. The device is especially useful when the clock rate remains below its 500 MHz maximum rating.
अनुशंसित
Industrial Data Acquisition Systems
The SY89809LTH can distribute a common high-speed sampling or processing clock across multiple converter, filter, and communication sections in an industrial data-acquisition system. Its differential HSTL outputs improve noise rejection in environments containing motors, switching supplies, and long PCB routes, while the 2:9 topology permits clock selection when a redundant source is present. The device's nine output pairs let designers avoid adding numerous separate buffers close to the source. At the board level, use continuous reference planes, controlled differential impedance, and termination that matches the actual receiver configuration. Keep clock routing away from high-current switching paths and verify the complete channel at the highest intended operating frequency.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा SY89809LTH — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Brand | Microchip Technology |
| Package | 32-pin TQFP |
| Product Type | Clock fanout buffer and multiplexer IC |
| Fanout Ratio | 2:9 |
| Maximum Frequency | 500 MHz |
| Input Logic | LVPECL and HSTL |
| Output Logic | 9 differential HSTL output pairs |
| Maximum Part-to-Part Skew | 200 ps |
| Maximum Pin-to-Pin Skew | 50 ps |
| Supply Voltage | 3.3 V nominal |
मुख्य विशेषताएँ
- High fanout in a single clock-buffer package (बनामSingle-output clock buffers)
- High operating frequency with defined skew (बनामLower-frequency general-purpose clock buffers)
- Integrated source multiplexing (बनामSingle-input fanout buffers)
डिज़ाइन नोट्स
Route every differential clock output as a controlled-impedance pair with a continuous reference plane and no unnecessary stubs. Match the differential impedance to the PCB stack-up and use the same termination strategy at each receiver. At 500 MHz, connector launches, vias, and package transitions can contribute more timing uncertainty than the specified 50 ps pin-to-pin skew, so include them in channel simulation and measurement.
Treat LVPECL and HSTL input requirements as distinct interface conditions even though both are supported. Confirm source amplitude, common-mode voltage, input termination, and the exact input selected by the two-input multiplexer. Maintain short, symmetric clock paths and avoid routing a high-speed clock adjacent to switching nodes. Verify edge rate and degradation at the far receiver rather than assuming the source frequency alone guarantees adequate signal margin.
Do not confuse the LTH ordering code with a different functional device. The associated SY89809LTH-TR listing represents a packaging option, but reel versus tray must be checked against the assembly process. Also distinguish the 50 ps pin-to-pin skew from the 200 ps part-to-part skew: the first constrains outputs within one package, while the second constrains matching devices and must be included in multi-chip timing analysis.
Provide the manufacturer-recommended input and output decoupling arrangements directly around the device and keep high-current return paths out of the clock region. If the board uses split or heavily segmented power planes, add stitching capacitors where permitted so the clock-output return current has a continuous low-impedance path. Check the exposed-pad and thermal requirements in the 32-pin TQFP layout guidance before releasing the board.
अनुपालन जानकारी
The available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Request current compliance documentation from Microchip Technology before using the device in a regulated or automotive design.