Microchip Technology

SY89809LTH - 2:9 500 MHz Clock Fanout Buffer | Microchip

MPN: SY89809LTH ✓ Hoạt động
3.3 V Vdss 32-pin TQFP Package 500 MHz Speed
MOQ: 1 |

SY89809LTH Tóm tắt

The Microchip Technology SY89809LTH is a 2:9 clock fanout buffer and multiplexer IC with a maximum clock frequency of 500 MHz, supplied in a 32-pin TQFP package. It accepts LVPECL and HSTL clock inputs and produces nine differential HSTL output pairs for high-speed clock distribution. The SY89809LTH is intended for systems that need one source clock to be distributed across multiple destination circuits without introducing excessive part-to-part or pin-to-pin skew.

A clock fanout buffer is a clock-management semiconductor that reproduces an incoming periodic signal across multiple outputs. Clock buffers and drivers sit within the clock and timing hierarchy, where they complement oscillators, phase-locked loops, dividers, and multiplexers. Their principal design roles are to restore signal integrity, provide output drive, isolate destinations, and maintain predictable timing relationships across a board or backplane.

The SY89809LTH supports a maximum operating frequency of 500 MHz. Its input interface accepts both LVPECL and HSTL signals, allowing compatibility with several common high-speed clocking conventions. The output stage provides nine differential HSTL pairs, while the documented output configuration is capable of driving 50 ohms to ground without an offset voltage. These characteristics make the device applicable to demanding clock-distribution trees rather than low-frequency general-purpose buffering.

Timing performance is a central consideration for this device. The Micrel manufacturer datasheet specifies a maximum part-to-part skew of 200 ps and a maximum pin-to-pin skew of 50 ps. Pin-to-pin skew describes variation between outputs of the same device, while part-to-part skew covers variation between different devices. These limits are particularly important when clocked logic must maintain source-synchronous relationships or when downstream receivers operate with limited timing margins.

Typical uses include high-speed server and storage interfaces, network-switch backplanes, telecommunications equipment, test-and-measurement systems, and other multi-drop clocking architectures. The device can also support clock muxing and distribution where two input sources must feed nine output locations. System designers should preserve controlled impedance and adequate return paths between the driver and each receiver to maintain the intended signal quality.

The principal design trade-off is operating speed versus integration and termination complexity. A 500 MHz differential HSTL clock network requires careful PCB stack-up, impedance control, termination, and clock-tree topology. The SY89809LTH provides nine differential outputs in one package, reducing the number of separate fanout stages needed for a wide distribution network.

This page consolidates the device's clock topology, frequency, interface, skew, package, and sourcing characteristics, then adds application guidance and verified-source links. It also distinguishes the LTH tray designation from other ordering options and explains what an engineer should confirm before treating another device as a drop-in replacement.

Bộ thay thế dễ dàng lắp đặt cho SY89809LTH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

SY89809LTH-TR

✅ Drop-In
📦 32-pin TQFP
Same 500 MHz clock rating, 1:9 fanout, logic levels, and 32-pin TQFP package; only the commercial ordering suffix differs, with no stated electrical parameter difference

📋 Tham chiếu thay thế (không có trong danh mục)

SY89809LTH Thông số kỹ thuật

Product Type Clock fanout buffer and multiplexer IC
Fanout Ratio 2:9
Tần số xung maksimum 500 MHz
Number of Inputs 2 inputs
Số lượng đầu ra 9 differential output pairs
Supported Input Logic LVPECL and HSTL
Output Logic Differential HSTL
Nominal Supply Voltage 3.3 V
Output Impedance 50 ohm to ground
Output DC Offset 0 V
Maximum Part-to-Part Skew 200 ps
Maximum Pin-to-Pin Skew 50 ps
Hộp 32-pin TQFP

Hướng dẫn cấu hình chân SY89809LTH 32-pin tqfp

Cấu hình chân cho SY89809LTH (32-pin tqfp gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 32-pin tqfp cho SY89809LTH

Không có dữ liệu chân cụ thể sẵn có cho SY89809LTH.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

SY89809LTH phù hợp cho 6 Áp dụngs: Server Platform Clock Distribution, Network Switch Backplane Clocking, Telecommunications Equipment Clock Fanout, Storage Controller Clock Distribution, Test and Measurement Clocking, Industrial Data Acquisition Systems.

🖥️

Server Platform Clock Distribution

The SY89809LTH fits server clock trees that distribute a common source to multiple processor, memory, interface, or fabric clock domains below the 500 MHz device rating. Two selectable inputs support clock multiplexing, while nine differential HSTL output pairs provide substantial fanout without requiring a chain of small buffers. The 50 ps maximum pin-to-pin skew gives circuit designers a defined relationship among outputs from one device. In practice, the design must use controlled-impedance routing, suitable return paths, and receiver-appropriate termination. The low-voltage differential outputs also reduce noise sensitivity compared with single-ended distribution, although connector and package transitions must remain included in the channel-budget analysis.

🌐

Network Switch Backplane Clocking

The SY89809LTH is suitable for network-switch backplanes where a low-jitter reference clock must reach multiple line cards, ports, or internal processing blocks. Its two-input multiplexing capability can support source selection or redundancy control, and nine differential HSTL pairs provide enough outputs for a broad distribution tree. The device's 500 MHz maximum clock frequency accommodates high-speed digital architectures, while the 50 ps maximum pin-to-pin skew helps preserve alignment between related clock domains. Backplane implementation should account for connector loss, return discontinuities, and impedance transitions, because the IC cannot compensate for an uncontrolled transmission-line environment after the signal leaves its outputs.

📡

Telecommunications Equipment Clock Fanout

The SY89809LTH can distribute a 500 MHz-or-lower system clock across multiple telecommunications processing sections when low-voltage differential signaling is appropriate. Nine output pairs allow a central source to feed several converters, interface engines, or fabric blocks while keeping the clock topology manageable. LVPECL and HSTL input support makes the device adaptable to common high-speed clock-generation chains. Because part-to-part skew is specified up to 200 ps, system timing analysis should distinguish outputs from the same package from clocks originating in different devices. Controlled PCB impedance and short return paths remain essential for preserving edge quality across cabinet-scale equipment.

💾

Storage Controller Clock Distribution

The SY89809LTH can provide a multi-output clock source for storage controllers, NAND-interface logic, memory controllers, and associated data-path circuitry. Its 2:9 architecture permits one of two clocks to be selected and distributed across as many as nine differential outputs, reducing the number of separate clock-driver stages required in a dense board. At frequencies below 500 MHz, the device supplies useful integration while maintaining specified pin-to-pin and part-to-part skew limits. Layout should keep the clock distribution symmetric where possible, provide uninterrupted reference planes, and avoid stubs that could create reflections. Validate the complete clock path with the actual receiver loads and enclosure transitions.

🔧

Test and Measurement Clocking

The SY89809LTH is appropriate for test-and-measurement systems that must distribute a precise high-speed trigger, reference, or sampling clock among multiple instruments or acquisition channels. Two input selection and nine differential outputs allow a compact front end to support multiple instruments without creating a long chain of cascaded fanout devices. The 50 ps maximum pin-to-pin skew provides a useful measure of coherence among outputs from the same package. Designers should account for cable and connector losses, use appropriate differential terminations, and keep the clock source and distribution paths separated from noisy switching nodes. The device is especially useful when the clock rate remains below its 500 MHz maximum rating.

🏭

Industrial Data Acquisition Systems

The SY89809LTH can distribute a common high-speed sampling or processing clock across multiple converter, filter, and communication sections in an industrial data-acquisition system. Its differential HSTL outputs improve noise rejection in environments containing motors, switching supplies, and long PCB routes, while the 2:9 topology permits clock selection when a redundant source is present. The device's nine output pairs let designers avoid adding numerous separate buffers close to the source. At the board level, use continuous reference planes, controlled differential impedance, and termination that matches the actual receiver configuration. Keep clock routing away from high-current switching paths and verify the complete channel at the highest intended operating frequency.

What is the SY89809LTH used for?
The SY89809LTH is a 2:9 clock fanout buffer and multiplexer IC used to distribute a high-speed clock to as many as nine differential output pairs. According to the Micrel manufacturer datasheet, it accepts LVPECL and HSTL inputs, supports frequencies up to 500 MHz, and provides differential HSTL outputs. It is suited to clock trees in network, server, storage, telecommunications, and test systems where several destinations need a closely related clock.
What is the maximum frequency of the SY89809LTH?
The SY89809LTH has a maximum operating clock frequency of 500 MHz. This figure appears in the Micrel manufacturer datasheet and in the product classification for the 2:9 clock fanout buffer. The supported frequency also depends on PCB signal integrity, source amplitude, clock topology, termination, and receiver loading, so 500 MHz should be treated as the device rating rather than a guarantee for every implementation.
How many outputs does the SY89809LTH provide?
The SY89809LTH provides nine differential HSTL output pairs from two clock inputs. Its 2:9 classification identifies the two-input to nine-output fanout arrangement. The output stage can drive 50 ohms to ground without an offset voltage, according to the Micrel manufacturer datasheet, making the device suitable for compact high-speed clock trees requiring multiple destinations.
What is the difference between SY89809LTH and SY89809LTH-TR?
The SY89809LTH and SY89809LTH-TR identify the same 2:9, 500 MHz, 32-pin TQFP clock buffer family, while their ordering codes indicate different delivery formats. The SY89809LTH is associated with tray packaging, whereas the SY89809LTH-TR ordering code is separately listed as a tray-and-reel option. Before substituting one ordering code for another, confirm the manufacturer ordering guide, temperature grade, reel orientation, and exposed-pad requirements.
What input logic levels are supported by SY89809LTH?
The SY89809LTH supports LVPECL and HSTL input logic. LVPECL is a low-voltage positive emitter-coupled logic interface, while HSTL is a low-voltage source-synchronous digital signaling standard. The Micrel manufacturer datasheet identifies both input types, allowing the device to sit within high-speed clock networks that use either convention. The actual receiver thresholds and termination arrangement must still follow the manufacturer application guidance.
What are the output logic and termination characteristics of SY89809LTH?
The SY89809LTH produces nine differential HSTL output pairs and is documented to drive 50 ohms to ground without output offset voltage. Differential HSTL improves noise immunity and timing margin in high-speed systems. Correct implementation still requires controlled-impedance PCB routing, a suitable return path, and termination consistent with the receiver and overall clock topology.
How much skew does the SY89809LTH introduce?
The Micrel manufacturer datasheet specifies a maximum part-to-part skew of 200 ps and a maximum pin-to-pin skew of 50 ps. Pin-to-pin skew is the difference between output pins of one device, whereas part-to-part skew describes differences between devices. The 50 ps internal limit is valuable for closely related clock outputs, while the 200 ps limit should be included in system-level timing analysis.
When should I choose the SY89809LTH over a smaller clock buffer?
Choose the SY89809LTH when one high-speed source must feed up to nine differential destinations and the design benefits from integrated two-input clock multiplexing. A smaller buffer may be preferable for fewer destinations, lower speed, lower channel count, or lower system complexity. The decisive factors are the required fanout ratio, maximum frequency, logic standard, skew budget, board topology, and availability of equivalent 32-pin devices.
Is the SY89809LTH suitable for server and storage clock trees?
The SY89809LTH can be suitable for server and storage clock trees that operate below 500 MHz and use LVPECL or HSTL clocking. Its nine differential output pairs reduce the number of separate fanout stages, while the 50 ps maximum pin-to-pin skew provides a defined relationship among outputs from the same device. Board-level impedance, insertion loss, connector transitions, and receiver timing margins must be validated over the complete clock path.
What is the best drop-in replacement for SY89809LTH?
No independently verified drop-in replacement is established for the SY89809LTH in the available manufacturer and cross-reference information. A genuine replacement must use the same 32-pin TQFP footprint, provide pin-compatible power, input, and output connections, accept the required LVPECL or HSTL clock, support nine differential HSTL outputs, and meet the 500 MHz target with acceptable skew. Treat packaging-code changes as ordering variants rather than functional substitutes until their ordering details are confirmed.
What can replace the SY89809LTH?
The SY89809LTH can be replaced only by a device whose pinout, electrical interface, output count, package, and timing performance have been verified. No confirmed cross-brand drop-in equivalent is identified in the available technical information. The SY89809LTH-TR ordering code is the closest documented same-family option, but its reel or tape-and-reel presentation must be checked against the target assembly process before substitution.
Is the SY89809LTH the same as a generic 1:9 clock buffer?
No generic 1:9 clock buffer should be assumed to be interchangeable with the SY89809LTH. Although both architectures may fan out one selected clock to nine outputs, the SY89809LTH also supports LVPECL and HSTL inputs, nine differential HSTL output pairs, a 500 MHz maximum frequency, and a defined 32-pin pinout. Those combined requirements determine whether another device is truly drop-in compatible.
Where can I download the SY89809LTH datasheet PDF?
The SY89809LTH datasheet PDF can be opened through the datasheet link on this product page, and the manufacturer data is also identified by the Micrel document title, “3.3V 1:9 High-Performance, Low-Voltage Bus Clock Driver.” Use the pin-description and electrical-characteristics tables in that document to assign PCB connections and confirm the final electrical limits before layout release.
Where can I find the SY89809LTH pinout?
The SY89809LTH pinout is defined by its 32-pin TQFP datasheet package and the manufacturer pin-description table. The public product records confirm the 32-pin TQFP construction and identify the device as a two-input, nine-output clock buffer. Follow the numbered pin table and exposed-pad guidance in the Micrel manufacturer datasheet rather than inferring connections solely from the package outline.
Where can I buy SY89809LTH and what is its price?
Use the “Request a Quote” form on this page to ask about SY89809LTH unit pricing, stock, minimum order quantity, and current lead time. The available product listings identify the exact MPN, but they do not present a qualifying quantity-break price table that can be reproduced as fixed pricing. The request can also confirm whether the LTH tray packaging is appropriate for the intended assembly process.
What is the lead time and stock status for SY89809LTH?
Request the current SY89809LTH stock position, lead time, and minimum order quantity through the “Request a Quote” form on this page. Product listings may change inventory and delivery conditions independently of technical specifications, so current supply status should be confirmed at the time of quotation. Include the required package form, quantity, and target delivery date in the request.
What are the key specifications of SY89809LTH that engineers should know?
The key SY89809LTH specifications are a 2:9 fanout architecture, 500 MHz maximum frequency, two inputs, nine differential HSTL output pairs, LVPECL and HSTL input support, 50-ohm-to-ground output drive, 200 ps maximum part-to-part skew, and 50 ps maximum pin-to-pin skew. The device is packaged in a 32-pin TQFP. These parameters collectively define its clock-distribution capability.
Does SY89809LTH comply with RoHS, REACH, or AEC-Q100?
RoHS, REACH, and AEC-Q100 status cannot be confirmed from the technical information associated with the SY89809LTH listing. The available records establish the clock-buffer function, frequency, interfaces, skew, and 32-pin TQFP package, but they do not state the required environmental or automotive qualifications. Request the current manufacturer declaration or product compliance documentation before using the device in a regulated or automotive design.

Dữ liệu tham khảo kỹ thuật cho SY89809LTH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the SY89809LTH when the design requires two selectable high-speed clock inputs, nine differential HSTL output pairs, and an operating frequency as high as 500 MHz. It is a strong fit for server, network, storage, telecommunications, industrial acquisition, and test systems where a compact fanout tree and controlled skew are important. Select a smaller single-output or lower-channel buffer when the system needs fewer destinations, operates at a substantially lower frequency, or has simpler routing requirements. For replacement decisions, require the same 32-pin TQFP footprint and confirm every power, input, output, enable, and exposed-pad connection. The SY89809LTH-TR ordering code is a packaging-format option rather than a different functional design. Before committing to any other part, compare input thresholds, output voltage and termination, maximum frequency, skew specifications, power consumption, and availability. If timing margins are tight, include the 200 ps part-to-part limit and the 50 ps pin-to-pin limit separately in the system budget.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Brand Microchip Technology
Package 32-pin TQFP
Product Type Clock fanout buffer and multiplexer IC
Fanout Ratio 2:9
Maximum Frequency 500 MHz
Input Logic LVPECL and HSTL
Output Logic 9 differential HSTL output pairs
Maximum Part-to-Part Skew 200 ps
Maximum Pin-to-Pin Skew 50 ps
Supply Voltage 3.3 V nominal

Bảo phân biệt quan trọng

  • High fanout in a single clock-buffer package (vsSingle-output clock buffers)
  • High operating frequency with defined skew (vsLower-frequency general-purpose clock buffers)
  • Integrated source multiplexing (vsSingle-input fanout buffers)

Ghi chú thiết kế

Route every differential clock output as a controlled-impedance pair with a continuous reference plane and no unnecessary stubs. Match the differential impedance to the PCB stack-up and use the same termination strategy at each receiver. At 500 MHz, connector launches, vias, and package transitions can contribute more timing uncertainty than the specified 50 ps pin-to-pin skew, so include them in channel simulation and measurement.

Treat LVPECL and HSTL input requirements as distinct interface conditions even though both are supported. Confirm source amplitude, common-mode voltage, input termination, and the exact input selected by the two-input multiplexer. Maintain short, symmetric clock paths and avoid routing a high-speed clock adjacent to switching nodes. Verify edge rate and degradation at the far receiver rather than assuming the source frequency alone guarantees adequate signal margin.

Do not confuse the LTH ordering code with a different functional device. The associated SY89809LTH-TR listing represents a packaging option, but reel versus tray must be checked against the assembly process. Also distinguish the 50 ps pin-to-pin skew from the 200 ps part-to-part skew: the first constrains outputs within one package, while the second constrains matching devices and must be included in multi-chip timing analysis.

Provide the manufacturer-recommended input and output decoupling arrangements directly around the device and keep high-current return paths out of the clock region. If the board uses split or heavily segmented power planes, add stitching capacitors where permitted so the clock-output return current has a continuous low-impedance path. Check the exposed-pad and thermal requirements in the 32-pin TQFP layout guidance before releasing the board.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Request current compliance documentation from Microchip Technology before using the device in a regulated or automotive design.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

SY89809LTH datasheet SY89809LTH pinout SY89809LTH datasheet pdf SY89809LTH equivalent SY89809LTH replacement SY89809LTH drop-in replacement SY89809LTH 500 MHz SY89809LTH 32 TQFP SY89809LTH HSTL outputs SY89809LTH vs SY89809LTH-TR SY89809LTH price SY89809LTH stock Microchip Technology SY89809LTH SY89809LTH clock fanout buffer

Các bộ phận và thuật ngữ liên quan

Microchip Technology Micrel SY89809LTH SY89809LTH-TR clock fanout buffer clock multiplexer clock buffer clock driver clock-management IC integrated circuit semiconductor LVPECL HSTL differential output 500 MHz 50 ps pin-to-pin skew 200 ps part-to-part skew 32-pin TQFP TQFP package surface-mount package server clock tree network backplane storage controller test and measurement industrial data acquisition
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ