Texas Instruments

TAS5631DKD - 300W Stereo Class D Power Stage | Texas Instruments

MPN: TAS5631DKD ✓ सक्रिय
25 V to 52.5 V Vdss 44-pin HTSSOP (DKD) Package
न्यूनतम ऑर्डर मात्रा: 1 |

TAS5631DKD अवलोकन

The Texas Instruments TAS5631DKD is a PWM-input Class D audio power amplifier built on PurePath HD technology with integrated closed-loop feedback, capable of delivering 300 W per channel in stereo into 4- to 8-ohm speakers from a single 50 V supply, or 600 W in mono, in a 44-pin HTSSOP (DKD) package. The power stage accepts a 3.3 V-compatible PWM input rather than an analog signal, and operates from a 25 V to 52.5 V supply range with a 10.8 V to 13.2 V control/PWM supply domain.

A Class D audio power amplifier is a switching power stage in which the output transistors are driven fully on and fully off, so the device dissipates far less energy than a linear (Class AB) amplifier at the same output level. Class D stages are the default choice for high-power consumer and professional audio: they combine high efficiency with high current capability into low-impedance loads. The PurePath HD family sits one level above ordinary Class D, adding a self-contained feedback loop inside the power stage so that distortion can be held below 0.03% without an external analog feedback network.

Key features include 300 W stereo and 600 W mono output capability, integrated closed-loop feedback, PWM input with no analog input pin, an efficiency of roughly 90% at full power, integrated undervoltage and overcurrent protection, and an exposed thermal pad on the HTSSOP-44 package for direct coupling to the PCB copper. The device is intended to be paired with a PWM processor such as the TAS5086 to form a complete chipset.

Technically the TAS5631 is a self-contained power stage: four bridge-tied output channels drive the speaker outputs, and the on-die feedback network senses the output voltage and corrects the drive so that the effective loop gain stays high even with long speaker cable runs and inverting or non-inverting configurations. Because the feedback is internal, the design work shifts from analog loop compensation to digital PWM generation, timing, and thermal management of the board.

Typical applications include multi-channel home theater and AV receivers, active soundbars and wireless loudspeakers, powered subwoofers, smart speakers with cloud audio playback, professional powered speakers and stage-monitor amplifiers, and automotive head-unit or amplifier sub-systems.

The dominant design consideration is thermal. At 300 W per channel into a 4-ohm load, the output stage dissipates a substantial fraction of the DC input power, so the exposed thermal pad must be soldered with a proper thermal via array and tied to a large copper pour, otherwise output power must be derated. Follow the recommended PCB layout, filter, and thermal via guidelines in the manufacturer datasheet when laying out the power stage.

This page combines the manufacturer power-stage specifications with practical thermal, layout, and signal-chain guidance, drop-in replacement options in the same 44-pin HTSSOP footprint, and application notes that go beyond a parameter table.

के लिए ड्रॉप-इन विकल्प TAS5631DKD — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं TAS5631DKD (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package.

Texas Instruments
Package: 44-pin HSSOP with exposed pad
इसके साथ तुलना करें TAS5631DKD →

TAS5615DKDR

✅ ड्रॉप-इन
📦 44-pin HTSSOP (DKD)
same 44-HSSOP footprint and 300 W stereo rating, but accepts an analog input instead of a PWM input; cross-reference listings rate it a complete replacement

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TAS5631BDKDR

✅ ड्रॉप-इन
📦 44-pin HTSSOP (DKD)
identical power stage and 44-HSSOP package, newer datasheet revision B; output power and supply range unchanged (0% difference)

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TAS5616DKDR

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 44-pin HTSSOP (DKD)
same 44-HSSOP package and stereo Class D topology; input interface and exact output power rating differ from the TAS5631

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TAS5618DKDR

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 44-pin HTSSOP (DKD)
same 44-HSSOP power-stage package and stereo Class D topology; output power per channel is lower than the 300 W rating of the TAS5631

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TAS5613DKDR

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 44-pin HTSSOP (DKD)
same 44-HSSOP footprint and PurePath HD class D technology; substantially lower per-channel output power than 300 W (approx. 30% class)

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TAS5631DKD Maximum Ratings और Electrical Characteristics

Device Type Class D audio power amplifier (PWM input)
Channel Configuration 1-channel (mono) or 2-channel (stereo)
Maximum Output Power (Stereo) 300 W
Maximum Output Power (Mono) 600 W
Supply Voltage Range (PVDD) 25 V to 52.5 V
Control / PWM Supply Voltage Range 10.8 V to 13.2 V
Feedback Topology Integrated closed-loop feedback (PurePath HD)
Total Harmonic Distortion + Noise < 0.03%
Supported Load Impedance 4 ohm to 8 ohm
पैकेज 44-pin HTSSOP (DKD)
पिन काउंट 44
Thermal Pad Exposed pad for PCB thermal sinking
माउंटिंग प्रकार Surface mount
Protection Features Integrated undervoltage and overcurrent protection
Datasheet Length 33 pages
RoHS स्थिति Compliant

TAS5631DKD 44-pin htssop (dkd) पिन कॉन्फ़िगरेशन गाइड

TAS5631DKD (44-pin htssop (dkd) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

TAS5631DKD के लिए 44-pin htssop (dkd) पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: TAS5631DKD.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

TAS5631DKD के लिए उपयुक्त है 6 अनुप्रयोगs: Multi-Channel Home Theater Power Amplifier, Powered Soundbar and Active Loudspeaker, Powered Subwoofer Amplifier Module, Professional Powered Speaker and Stage Monitor, Smart Speaker and Networked Loudspeaker, Automotive and Marine Audio Sub-System Amplifier.

📺

Multi-Channel Home Theater Power Amplifier

The TAS5631DKD fits multi-channel home theater amplification because each 44-pin power stage delivers 300 W per channel from a single 50 V rail while keeping THD+N below 0.03%, which preserves the low distortion needed for movie dialogue and music playback in a living room. Pair it with a PWM modulator such as the TAS5086, feed the two PWM channels into the power stage, and configure the device for stereo or bridged mono. The integrated PurePath HD feedback removes the external speaker feedback network, so the amplifier board needs only output inductors, a bulk electrolytic bank, and a clean ground return. Because 300 W of real audio output dissipates several watts in the switching stage, the exposed thermal pad must be tied to a full copper pour with a dense thermal via array.

🎧

Powered Soundbar and Active Loudspeaker

Active soundbars and wireless bookshelf speakers need high continuous power in a thin enclosure, and the TAS5631DKD supplies up to 300 W per channel with roughly 90% conversion efficiency, so more of the available supply power reaches the speaker instead of being lost as heat in the cabinet. The 25 V to 52.5 V supply range lets a designer run a 36 V or 48 V rail from a compact boost converter. The PWM input means the whole signal chain can be digital from the wireless or network audio module through to the power stage, eliminating analog interconnects. Integrated undervoltage and overcurrent protection adds robustness for unattended consumer products, and the 44-pin HTSSOP footprint keeps board area small enough for a slim soundbar chassis.

🔧

Powered Subwoofer Amplifier Module

A dedicated powered subwoofer module can use the TAS5631DKD in bridged mono mode for up to 600 W into a 4-ohm driver, which is the power class where excursion control and headroom matter most. Bridged operation uses both output halves in push-pull, so the module needs a single high-current output inductor pair and a supply rated above the 52.5 V maximum, typically 50 V. The integrated closed-loop PurePath HD feedback keeps distortion below 0.03% even with long or inverting speaker cables, which limits audible harmonic coloration in the low frequency band. Subwoofer modules are typically built as a replaceable amplifier card, so the 44-pin HTSSOP power stage and its thermal pad layout make board servicing simple.

🏭

Professional Powered Speaker and Stage Monitor

Professional powered speakers and stage monitors operate for hours at high average power, and the TAS5631DKD is a strong fit because the PurePath HD closed-loop feedback holds total harmonic distortion plus noise below 0.03% while the switching topology keeps stage-level efficiency high and idle dissipation low. Digital-ready professional systems often drive the stage from a mixer with an AES or Dante interface, so the PWM-input architecture avoids long analog runs and keeps the signal path fully digital until the final power stage. On-site repairability matters in touring rigs, and the 44-pin HTSSOP package with a single exposed thermal pad is straightforward to rework with standard tools. Board thermal design must target sustained full-power operation with the amplifier in a sealed cabinet.

🧩

Smart Speaker and Networked Loudspeaker

Smart speakers and networked loudspeakers combine cloud or local playback with voice assistant microphones, so they need a power stage with high efficiency and low idle draw to survive on limited supply current. The TAS5631DKD keeps quiescent dissipation low by operating as a switching stage, and its PWM input lets the system stay digital from the Wi-Fi audio decoder to the speaker, which prevents analog noise pickup near microphone preamplifiers. Operating from a 25 V to 52.5 V rail suits compact boost-converter architectures common in smart speakers. Use of an integrated closed-loop feedback network also means fewer discrete components and less sensitive layout, which helps yield on high-volume consumer builds. Thermally, a 100 W to 150 W stereo operating point is typical and easily handled with a moderate copper pour on a four-layer board.

🚗

Automotive and Marine Audio Sub-System Amplifier

High-power audio sub-systems in vehicle and marine installations, such as compact amplifiers for in-boom or rear-seat subwoofers, can benefit from the TAS5631DKD because it sustains 300 W stereo or 600 W bridged mono from a 25 V to 52.5 V supply that matches a boosted 12 V automotive rail architecture. The switching efficiency keeps the case heat manageable in a sealed enclosure, and integrated undervoltage and overcurrent protection helps survive cranking transients. Because this device is not an AEC-Q100 qualified variant, confirm the qualification status of the exact ordering code with the manufacturer before committing it to a vehicle platform. Use the exposed thermal pad and via fence tied to the chassis or a large pour for the highest sustained output levels.

What is the TAS5631DKD?
The TAS5631DKD is a PWM-input Class D audio power amplifier from Texas Instruments that delivers up to 300 W per channel in stereo or 600 W in mono. It uses PurePath HD technology with integrated closed-loop feedback, so the power stage corrects its own output without an external analog feedback network. According to the TI TAS5631 datasheet, the device is packaged in a 44-pin HTSSOP (DKD) and is intended to be driven by a PWM processor such as the TAS5086.
How much output power can the TAS5631DKD deliver?
The TAS5631DKD delivers up to 300 W per channel in stereo operation into 4- to 8-ohm speakers from a single 50 V supply, and up to 600 W when the part is configured as a mono bridge stage. The TI product page lists the device as a 300 W stereo Class D amplifier with integrated feedback. Real usable power depends on supply voltage, load impedance, and board thermal performance, so derate for enclosure temperature.
What is the supply voltage range of the TAS5631DKD?
The TAS5631DKD operates from 25 V to 52.5 V on its main power supply, which is what allows a 50 V rail to deliver the headline 300 W stereo output. Distributor listings for this part also cite a 10.8 V to 13.2 V control and PWM supply domain, which supplies the switching bias and the logic rails for the modulator interface. Both ranges are specified in the manufacturer TAS5631 datasheet.
What package does the TAS5631DKD come in and how many pins does it have?
The TAS5631DKD ships in a 44-pin HTSSOP package, also called a 44-HSSOP, and is designated with the DKD ordering code. The package includes an exposed thermal pad that must be soldered to the PCB copper pour and connected with a dense array of thermal vias. Because the exposed pad is part of the thermal path rather than an additional signal pin, layout must follow the datasheet land pattern and paste stencil recommendations exactly.
What is PurePath HD and why does it matter for the TAS5631?
PurePath HD is Texas Instruments' closed-loop feedback technology integrated directly into the power stage. Instead of relying on external speaker feedback resistors, the TAS5631 senses its own output and corrects drive in real time, holding total harmonic distortion plus noise below 0.03% while maintaining roughly 90% conversion efficiency. This is what allows Class D efficiency with Class AB-like linearity in a single 44-pin power stage.
What is the difference between the TAS5631DKD and the TAS5615DKDR?
The TAS5615DKDR is a 300 W stereo Class D amplifier in the same 44-HSSOP package, and component cross-reference listings mark it as a complete replacement for the TAS5631DKD because the terminals and packages are consistent. The distinction is architectural: the TAS5631 is a PWM-input power stage designed to be paired with a PWM processor, while the TAS5615 accepts an analog input directly. Verify your signal chain before swapping.
Is the TAS5631DKD suitable for automotive audio applications?
The TAS5631DKD is a general-purpose consumer and industrial power stage and is not listed as AEC-Q100 qualified, so it should not be placed in a safety-critical automotive position without separate qualification. It is frequently used for high-power audio sub-systems such as amplifiers, soundbars, and powered speakers. For automotive-grade requirements, source an explicitly qualified variant from the manufacturer rather than assuming this part is automotive rated.
Where can I download the TAS5631DKD datasheet PDF?
The manufacturer datasheet is available directly from Texas Instruments at https://www.ti.com/lit/ds/symlink/tas5631.pdf, and the product landing page with ordering information and quality documents is at https://www.ti.com/product/TAS5631. The datasheet runs 33 pages and includes the audio specification, electrical characteristics, typical application circuit, PCB layout guidance, and the pin configuration table. Download the PDF from the TI link before committing to a footprint.
Where do I find the TAS5631DKD pinout?
The TAS5631DKD pin configuration is documented in the pin connection table of the manufacturer TAS5631 datasheet, where all 44 HTSSOP pins are assigned to power, ground, PWM inputs, feedback, control logic, and thermal pad functions. Use that table when assigning PCB tracks, especially for the high-current PVDD and output pins, and observe the recommended thermal via pattern for the exposed pad. Ask your XAIPART representative for the annotated pin drawing if you need a marked-up package drawing for your schematic capture.
How much does the TAS5631DKD cost and where can I buy it?
Pricing for the TAS5631DKD moves with supply and volume, so the current unit price and quantity breaks are shown on this page from live market data as of 2026-11-10. For a firm quote, use the Request a Quote form on this page and specify your order quantity, target date, and shipping country. Authorized distributors and the manufacturer carry the 44-HSSOP DKD ordering code; confirm the DKD suffix when ordering.
What is the lead time and stock status for the TAS5631DKD?
Lead time for the TAS5631DKD depends on the manufacturer build plan and current inventory position, which changes week to week. Request a Quote on this page to receive the current stock position, scheduled delivery date, and minimum order quantity for the 44-pin HTSSOP DKD ordering code. For new designs, request the lead time together with your forecast so a periodic supply commitment can be arranged.
What is the best drop-in replacement for the TAS5631DKD?
The best drop-in replacement is the TAS5631BDKDR, the same 44-HSSOP power stage with an updated datasheet revision, which cross-reference listings mark as a complete replacement with identical terminals and packages. For a functionally equivalent but architecturally different device, the TAS5615DKDR offers the same 300 W stereo capability in the same 44-HSSOP footprint. Always confirm the PWM-versus-analog input type before substituting.
When should I choose the TAS5631DKD over the TAS5631BDKDR?
Choose the TAS5631DKD when your BOM calls the original ordering code, and choose the TAS5631BDKDR when a newer datasheet revision or an automotive-qualified variant is required for your program. Electrically the two are the same 300 W stereo PWM-input power stage in the same 44-pin HTSSOP package, so the decision is mostly supply-chain, qualification, and documentation. Confirm pin and thermal layout are identical before changing the part number.
What is the difference between the TAS5631DKD and the TAS5631PHD?
The TAS5631PHD is not a drop-in replacement for the TAS5631DKD. The TAS5631DKD is a 44-pin HTSSOP (DKD) power stage, while the TAS5631PHD is offered in a 64-pin HTQFP package. Because the package pin count and land pattern differ, a swap requires a new PCB layout and different thermal management, and the resulting footprint is larger than the original HTSSOP. Treat this as a redesign, not a substitution.
Is the TAS5631DKD the same as the TAS5615DKDR?
No, they are not the same device, although both are 300 W stereo Class D amplifiers in the 44-HSSOP package. The TAS5631DKD is a PWM-input power stage with integrated PurePath HD closed-loop feedback that must be paired with a PWM modulator such as the TAS5086, while the TAS5615DKDR accepts an analog input directly. Component cross-reference tools rate the TAS5615DKDR as a complete replacement only for boards that already carry the PWM drive chain.
What can replace the TAS5631DKD in an existing design?
A drop-in replacement for the TAS5631DKD must be a 44-pin HTSSOP PWM-input Class D power stage of similar output capability. The TAS5631BDKDR matches on package and function, and the TAS5615DKDR matches on package, channel count, and 300 W stereo power rating. If your board drives the part from a PWM processor such as the TAS5086, keep that interface and confirm feedback configuration, supply sequencing, and thermal pad layout are unchanged.
What are the key specifications of the TAS5631DKD that engineers should know?
The TAS5631DKD is a 44-pin HTSSOP PWM-input Class D power stage rated for 300 W stereo or 600 W mono from a 25 V to 52.5 V supply, with a 10.8 V to 13.2 V control supply, integrated closed-loop PurePath HD feedback, THD+N below 0.03%, and support for 4- to 8-ohm loads. The manufacturer datasheet also specifies integrated undervoltage and overcurrent protection and an exposed thermal pad. Design effort therefore concentrates on PWM signal generation and PCB thermal design rather than analog loop compensation.

के लिए इंजीनियरिंग संदर्भ डेटा TAS5631DKD — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TAS5631DKD when your system drives the power stage from a PWM modulator such as the TAS5086 and needs up to 300 W per channel or 600 W bridged mono from a 25 V to 52.5 V rail with THD+N below 0.03%. Choose the TAS5631BDKDR when you need the newer datasheet revision or better supply continuity; it is electrically and mechanically identical to the DKD version. Choose the TAS5615DKDR only if your board still presents an analog drive signal, since it is a same-footprint part with a different input architecture. Choose the TAS5618DKDR or TAS5616DKDR when your power requirement is below the full 300 W stereo capability of the TAS5631 and you can accept the corresponding output power reduction. Avoid the TAS5631PHD as a substitution: its 64-pin HTQFP package requires a new layout. No cross-brand drop-in equivalent in the 44-HSSOP footprint was identified, so cross-brand substitution should be treated as a redesign.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TAS5615DKDR TAS5631BDKDR TAS5616DKDR TAS5618DKDR TAS5613DKDR
Package 44-pin HTSSOP (DKD) 44-pin HTSSOP (DKD) - same footprint 44-pin HTSSOP (DKD) - same footprint 44-pin HTSSOP (DKD) - same footprint 44-pin HTSSOP (DKD) - same footprint 44-pin HTSSOP (DKD) - same footprint
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

मुख्य विशेषताएँ

  • PWM input power stage frees the analog signal path (बनामTAS5615DKDR)
  • Higher single-channel power in the same 44-pin HTSSOP footprint (बनामTAS5613DKDR)
  • Exact package and footprint continuity for drop-in replacement (बनामTAS5631PHD)
  • Closed-loop PurePath HD feedback holds distortion below the Class D norm (बनामGeneric 300 W Class D power stage)

डिज़ाइन नोट्स

Estimated: with a 50 V supply, 300 W output per channel into 4 ohm, and an efficiency of roughly 90%, the output stage dissipates about 33 W per channel (600 W total DC input minus 600 W AC output). With a junction-to-ambient thermal resistance near 2 C/W on a well-via'd four-layer board, that implies a junction rise on the order of 65 C, so the thermal design must be verified against the actual junction-to-ambient value in the datasheet. Use the exposed pad with a dense array of thermal vias into a full top and bottom copper pour, keep the output inductors clear of the thermal path, and derate output power when the amplifier is enclosed in a cabinet.

Follow the recommended PCB layout in the manufacturer datasheet: keep the input, output, and power loop traces short and wide, place the bulk supply capacitors directly across the PVDD pins on the power stage side of the board, and route the PWM input traces as a short, quiet digital path away from the high-current output node. Because the PowerStage uses integrated closed-loop feedback, the feedback is internal to the package, so the critical external elements are the supply decoupling network, the output filter inductors, and the ground return. Do not split the power ground and signal ground with a cut that forces output current through signal traces.

A frequent design error is treating a PWM-input power stage like an analog-input amplifier. The TAS5631DKD requires a modulated PWM signal from a modulator such as the TAS5086; applying an analog audio voltage directly to the PWM pins produces no output and can damage the input network. Also confirm the phase relationship between the PWM inputs and the output configuration, since a swapped PWM pair inverts the channel. Finally, verify that the 25 V to 52.5 V supply range is respected, including boost converter overshoot at startup, since exceeding 52.5 V stresses the switching nodes.

The supply network for a 300 W per channel design must be sized for the full DC input current. Estimated: at 50 V and 90% efficiency, delivering 600 W of audio output draws about 13.3 A from the 50 V rail, plus inrush at turn-on. Specify low-ESR bulk electrolytic or polymer capacitors at the power stage, add local ceramic bypass close to each PVDD pin, and give the boost converter and inductor enough current margin for sustained full-power music rather than short sine bursts. Provide controlled sequencing between the 10.8 V to 13.2 V control supply and the main power rail.

Because the entire audio path is digital up to the power stage, PWM timing quality directly determines output distortion and EMI. Keep the PWM trace impedance continuous, avoid stubs, and place it adjacent to a solid ground plane; use the shortest possible connection to the modulator and avoid routing it beneath the output inductor region. Keep the modulator clocking scheme and dead-time settings consistent with the datasheet audio specification, which is measured with a TAS5086 chipset, so board-level deviations from that reference setup can move measured THD and noise figures.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Qualified
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

RoHS compliant per distributor product listings for the TAS5631DKD. The part is not listed as an AEC-Q100 qualified automotive variant; REACH, lead-free, halogen-free and conflict-minerals declarations are not stated in the available documentation.

डेटा सत्यापन तिथि: 2026-11-10 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

TAS5631DKD TAS5631DKD datasheet TAS5631DKD datasheet pdf TAS5631 pinout TAS5631 44-HSSOP pinout Texas Instruments TAS5631 TAS5631 300W stereo class D amplifier TAS5631 supply voltage 25V to 52.5V TAS5631DKD vs TAS5615DKDR TAS5631DKD vs TAS5631PHD TAS5631DKD drop-in replacement TAS5631DKD price TAS5631DKD stock and lead time TAS5631DKD application circuit PurePath HD TAS5631 power stage design

संबंधित कंपोनेंट्स और शब्द

Texas Instruments TAS5631DKD TAS5631 TAS5615DKDR TAS5631BDKDR TAS5616DKDR TAS5618DKDR TAS5613DKDR TAS5086 Class D amplifier audio power amplifier PWM input power stage PurePath HD closed-loop feedback HTSSOP-44 44-HSSOP QFN family surface mount SMD THD+N RoHS AEC-Q100 home theater amplifier powered subwoofer smart speaker exposed thermal pad semiconductor
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें