TAS5631DKD - 300W Stereo Class D Power Stage | Texas Instruments
MPN: TAS5631DKD ✓ NakahandaTAS5631DKD Ulas
A Class D audio power amplifier is a switching power stage in which the output transistors are driven fully on and fully off, so the device dissipates far less energy than a linear (Class AB) amplifier at the same output level. Class D stages are the default choice for high-power consumer and professional audio: they combine high efficiency with high current capability into low-impedance loads. The PurePath HD family sits one level above ordinary Class D, adding a self-contained feedback loop inside the power stage so that distortion can be held below 0.03% without an external analog feedback network.
Key features include 300 W stereo and 600 W mono output capability, integrated closed-loop feedback, PWM input with no analog input pin, an efficiency of roughly 90% at full power, integrated undervoltage and overcurrent protection, and an exposed thermal pad on the HTSSOP-44 package for direct coupling to the PCB copper. The device is intended to be paired with a PWM processor such as the TAS5086 to form a complete chipset.
Technically the TAS5631 is a self-contained power stage: four bridge-tied output channels drive the speaker outputs, and the on-die feedback network senses the output voltage and corrects the drive so that the effective loop gain stays high even with long speaker cable runs and inverting or non-inverting configurations. Because the feedback is internal, the design work shifts from analog loop compensation to digital PWM generation, timing, and thermal management of the board.
Typical applications include multi-channel home theater and AV receivers, active soundbars and wireless loudspeakers, powered subwoofers, smart speakers with cloud audio playback, professional powered speakers and stage-monitor amplifiers, and automotive head-unit or amplifier sub-systems.
The dominant design consideration is thermal. At 300 W per channel into a 4-ohm load, the output stage dissipates a substantial fraction of the DC input power, so the exposed thermal pad must be soldered with a proper thermal via array and tied to a large copper pour, otherwise output power must be derated. Follow the recommended PCB layout, filter, and thermal via guidelines in the manufacturer datasheet when laying out the power stage.
This page combines the manufacturer power-stage specifications with practical thermal, layout, and signal-chain guidance, drop-in replacement options in the same 44-pin HTSSOP footprint, and application notes that go beyond a parameter table.
Mga alternatibo na pwedeng ilagay na TAS5631DKD — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TAS5631DKD (parehas na form factor at footprint) — pagkakaiba sa Package.
TAS5615DKDR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TAS5631BDKDR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TAS5616DKDR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TAS5618DKDR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TAS5613DKDR
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TAS5631DKD Mga Pinakamataas na Rating at Electrical Characteristics
| Device Type | Class D audio power amplifier (PWM input) |
| Channel Configuration | 1-channel (mono) or 2-channel (stereo) |
| Maximum Output Power (Stereo) | 300 W |
| Maximum Output Power (Mono) | 600 W |
| Supply Voltage Range (PVDD) | 25 V to 52.5 V |
| Control / PWM Supply Voltage Range | 10.8 V to 13.2 V |
| Feedback Topology | Integrated closed-loop feedback (PurePath HD) |
| Total Harmonic Distortion + Noise | < 0.03% |
| Supported Load Impedance | 4 ohm to 8 ohm |
| Packhaging | 44-pin HTSSOP (DKD) |
| Bilang ng Pin | 44 |
| Thermal Pad | Exposed pad for PCB thermal sinking |
| Uri ng Pagpapasok | Surface mount |
| Protection Features | Integrated undervoltage and overcurrent protection |
| Datasheet Length | 33 pages |
| Tindminan RoHS | Compliant |
Gabay sa Pin Configuration ng TAS5631DKD 44-pin htssop (dkd)
Pin configuration para sa TAS5631DKD (44-pin htssop (dkd) package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa TAS5631DKD.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TAS5631DKD ay nararapat para sa 6 aplikasyons: Multi-Channel Home Theater Power Amplifier, Powered Soundbar and Active Loudspeaker, Powered Subwoofer Amplifier Module, Professional Powered Speaker and Stage Monitor, Smart Speaker and Networked Loudspeaker, Automotive and Marine Audio Sub-System Amplifier.
Multi-Channel Home Theater Power Amplifier
The TAS5631DKD fits multi-channel home theater amplification because each 44-pin power stage delivers 300 W per channel from a single 50 V rail while keeping THD+N below 0.03%, which preserves the low distortion needed for movie dialogue and music playback in a living room. Pair it with a PWM modulator such as the TAS5086, feed the two PWM channels into the power stage, and configure the device for stereo or bridged mono. The integrated PurePath HD feedback removes the external speaker feedback network, so the amplifier board needs only output inductors, a bulk electrolytic bank, and a clean ground return. Because 300 W of real audio output dissipates several watts in the switching stage, the exposed thermal pad must be tied to a full copper pour with a dense thermal via array.
Inirekomenda
Powered Soundbar and Active Loudspeaker
Active soundbars and wireless bookshelf speakers need high continuous power in a thin enclosure, and the TAS5631DKD supplies up to 300 W per channel with roughly 90% conversion efficiency, so more of the available supply power reaches the speaker instead of being lost as heat in the cabinet. The 25 V to 52.5 V supply range lets a designer run a 36 V or 48 V rail from a compact boost converter. The PWM input means the whole signal chain can be digital from the wireless or network audio module through to the power stage, eliminating analog interconnects. Integrated undervoltage and overcurrent protection adds robustness for unattended consumer products, and the 44-pin HTSSOP footprint keeps board area small enough for a slim soundbar chassis.
Inirekomenda
Powered Subwoofer Amplifier Module
A dedicated powered subwoofer module can use the TAS5631DKD in bridged mono mode for up to 600 W into a 4-ohm driver, which is the power class where excursion control and headroom matter most. Bridged operation uses both output halves in push-pull, so the module needs a single high-current output inductor pair and a supply rated above the 52.5 V maximum, typically 50 V. The integrated closed-loop PurePath HD feedback keeps distortion below 0.03% even with long or inverting speaker cables, which limits audible harmonic coloration in the low frequency band. Subwoofer modules are typically built as a replaceable amplifier card, so the 44-pin HTSSOP power stage and its thermal pad layout make board servicing simple.
Inirekomenda
Professional Powered Speaker and Stage Monitor
Professional powered speakers and stage monitors operate for hours at high average power, and the TAS5631DKD is a strong fit because the PurePath HD closed-loop feedback holds total harmonic distortion plus noise below 0.03% while the switching topology keeps stage-level efficiency high and idle dissipation low. Digital-ready professional systems often drive the stage from a mixer with an AES or Dante interface, so the PWM-input architecture avoids long analog runs and keeps the signal path fully digital until the final power stage. On-site repairability matters in touring rigs, and the 44-pin HTSSOP package with a single exposed thermal pad is straightforward to rework with standard tools. Board thermal design must target sustained full-power operation with the amplifier in a sealed cabinet.
Inirekomenda
Smart Speaker and Networked Loudspeaker
Smart speakers and networked loudspeakers combine cloud or local playback with voice assistant microphones, so they need a power stage with high efficiency and low idle draw to survive on limited supply current. The TAS5631DKD keeps quiescent dissipation low by operating as a switching stage, and its PWM input lets the system stay digital from the Wi-Fi audio decoder to the speaker, which prevents analog noise pickup near microphone preamplifiers. Operating from a 25 V to 52.5 V rail suits compact boost-converter architectures common in smart speakers. Use of an integrated closed-loop feedback network also means fewer discrete components and less sensitive layout, which helps yield on high-volume consumer builds. Thermally, a 100 W to 150 W stereo operating point is typical and easily handled with a moderate copper pour on a four-layer board.
Inirekomenda
Automotive and Marine Audio Sub-System Amplifier
High-power audio sub-systems in vehicle and marine installations, such as compact amplifiers for in-boom or rear-seat subwoofers, can benefit from the TAS5631DKD because it sustains 300 W stereo or 600 W bridged mono from a 25 V to 52.5 V supply that matches a boosted 12 V automotive rail architecture. The switching efficiency keeps the case heat manageable in a sealed enclosure, and integrated undervoltage and overcurrent protection helps survive cranking transients. Because this device is not an AEC-Q100 qualified variant, confirm the qualification status of the exact ordering code with the manufacturer before committing it to a vehicle platform. Use the exposed thermal pad and via fence tied to the chassis or a large pour for the highest sustained output levels.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TAS5631DKD — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TAS5615DKDR | TAS5631BDKDR | TAS5616DKDR | TAS5618DKDR | TAS5613DKDR |
|---|---|---|---|---|---|---|
| Package | 44-pin HTSSOP (DKD) | 44-pin HTSSOP (DKD) - same footprint | 44-pin HTSSOP (DKD) - same footprint | 44-pin HTSSOP (DKD) - same footprint | 44-pin HTSSOP (DKD) - same footprint | 44-pin HTSSOP (DKD) - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Pangunahing mga Pagkakaiba
- PWM input power stage frees the analog signal path (kumpara saTAS5615DKDR)
- Higher single-channel power in the same 44-pin HTSSOP footprint (kumpara saTAS5613DKDR)
- Exact package and footprint continuity for drop-in replacement (kumpara saTAS5631PHD)
- Closed-loop PurePath HD feedback holds distortion below the Class D norm (kumpara saGeneric 300 W Class D power stage)
Talaan ng Disenyo
Estimated: with a 50 V supply, 300 W output per channel into 4 ohm, and an efficiency of roughly 90%, the output stage dissipates about 33 W per channel (600 W total DC input minus 600 W AC output). With a junction-to-ambient thermal resistance near 2 C/W on a well-via'd four-layer board, that implies a junction rise on the order of 65 C, so the thermal design must be verified against the actual junction-to-ambient value in the datasheet. Use the exposed pad with a dense array of thermal vias into a full top and bottom copper pour, keep the output inductors clear of the thermal path, and derate output power when the amplifier is enclosed in a cabinet.
Follow the recommended PCB layout in the manufacturer datasheet: keep the input, output, and power loop traces short and wide, place the bulk supply capacitors directly across the PVDD pins on the power stage side of the board, and route the PWM input traces as a short, quiet digital path away from the high-current output node. Because the PowerStage uses integrated closed-loop feedback, the feedback is internal to the package, so the critical external elements are the supply decoupling network, the output filter inductors, and the ground return. Do not split the power ground and signal ground with a cut that forces output current through signal traces.
A frequent design error is treating a PWM-input power stage like an analog-input amplifier. The TAS5631DKD requires a modulated PWM signal from a modulator such as the TAS5086; applying an analog audio voltage directly to the PWM pins produces no output and can damage the input network. Also confirm the phase relationship between the PWM inputs and the output configuration, since a swapped PWM pair inverts the channel. Finally, verify that the 25 V to 52.5 V supply range is respected, including boost converter overshoot at startup, since exceeding 52.5 V stresses the switching nodes.
The supply network for a 300 W per channel design must be sized for the full DC input current. Estimated: at 50 V and 90% efficiency, delivering 600 W of audio output draws about 13.3 A from the 50 V rail, plus inrush at turn-on. Specify low-ESR bulk electrolytic or polymer capacitors at the power stage, add local ceramic bypass close to each PVDD pin, and give the boost converter and inductor enough current margin for sustained full-power music rather than short sine bursts. Provide controlled sequencing between the 10.8 V to 13.2 V control supply and the main power rail.
Because the entire audio path is digital up to the power stage, PWM timing quality directly determines output distortion and EMI. Keep the PWM trace impedance continuous, avoid stubs, and place it adjacent to a solid ground plane; use the shortest possible connection to the modulator and avoid routing it beneath the output inductor region. Keep the modulator clocking scheme and dead-time settings consistent with the datasheet audio specification, which is measured with a TAS5086 chipset, so board-level deviations from that reference setup can move measured THD and noise figures.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliant per distributor product listings for the TAS5631DKD. The part is not listed as an AEC-Q100 qualified automotive variant; REACH, lead-free, halogen-free and conflict-minerals declarations are not stated in the available documentation.