Texas Instruments

THS1007CDA - 10-Bit 6 MSPS Quad ADC | Texas Instruments

MPN: THS1007CDA ✓ सक्रिय
4.75 V to 5.25 V Vdss TSSOP-32 Package
न्यूनतम ऑर्डर मात्रा: 1 |

THS1007CDA अवलोकन

The Texas Instruments THS1007CDA is a 10-bit, 6 MSPS, four-channel simultaneous-sampling analog-to-digital converter with a parallel DSP and microprocessor interface, supplied in a 32-pin TSSOP package. It provides one 6 MSPS conversion pipeline for four analog inputs, with an operating supply range of 4.75 V to 5.25 V.

An ADC is an interface IC that converts an analog voltage into a digital code for processing, measurement, or control. A simultaneous-sampling ADC captures all four channels during the same conversion interval, allowing phase, gain, timing, and vibration signals to be compared without the timing offset introduced by sequential multiplexers. Within the product hierarchy, the THS1007CDA is an ADC, a data-conversion IC, and a semiconductor.

The principal features include 10-bit resolution, four analog inputs, simultaneous sampling, and a 6 MSPS conversion rate. Its parallel interface supports direct connection with digital signal processors and microprocessors, while automatic channel scanning helps reduce control overhead in multichannel systems. The manufacturer also identifies internal reference voltages of 1.5 V and 3.5 V and permits an external reference when tighter DC accuracy or temperature-drift control is required.

The converter uses a proprietary sampling architecture and a pipelined conversion process. Four analog inputs are sampled simultaneously, and the resulting digital values are presented through the parallel data interface. This architecture is useful when preserving relative timing among channels matters more than using the highest conversion rate available from a multiplexed converter. Because the part is specified for a 4.75 V to 5.25 V supply, system designers should account for the voltage relationship among the analog inputs, digital interface levels, reference voltage, and supply rails.

Typical uses include industrial process monitoring, vibration analysis, motor and drive diagnostics, instrumentation, communications equipment, and multichannel data-acquisition systems. Simultaneous sampling is particularly valuable in vibration monitoring, where phase differences between sensors can reveal imbalance, misalignment, or mechanical resonance. The parallel bus is also appropriate for systems whose processor reads complete conversion frames rather than using a serial ADC.

For a robust design, follow the pin-description table and application circuit in the manufacturer datasheet, place analog and digital return paths carefully, and account for acquisition time, reference accuracy, input bandwidth, and digital-interface timing. The TSSOP package provides a compact surface-mount solution, but its exposed thermal behavior and the converter's operating range should be checked against the system temperature requirements.

के लिए ड्रॉप-इन विकल्प THS1007CDA — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं THS1007CDA (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package Type.

Texas Instruments
Package Type: 32-pin TSSOP (DA)
इसके साथ तुलना करें THS1007CDA →

THS1007IDA

✅ ड्रॉप-इन
Texas Instruments
📦 TSSOP-32
10 bit · 4 channels · 6 MSPS · Simultaneous sampling · 1 stage · Parallel DSP and microprocessor interface · Supported · -40°C to 85°C

कीमत के लिए संपर्क करें

डेटाशीट देखें →

THS1007CDA Maximum Ratings और Electrical Characteristics

Converter Type 10-bit pipelined ADC
Analog Input Channels 4 channels
Sampling Architecture Simultaneous sampling
Conversion Rate 6 MSPS
रेज़ोल्यूशन 10 bit
Output Interface Parallel DSP/microprocessor interface
Analog Supply Voltage 4.75 V to 5.25 V
Internal Reference Voltage 1 1.5 V
Internal Reference Voltage 2 3.5 V
External Reference Support Yes
Channel Auto-Scan Supported
Commercial Operating Temperature 0°C to 70°C
Industrial Operating Temperature -40°C to 85°C
Package Type TSSOP-32
Terminal Count 32 terminals
Package Shape Rectangular gull-wing
माउंटिंग प्रकार Surface mount
Power-Supply Voltage 4.75 V to 5.25 V

THS1007CDA rectangular gull-wing पिन कॉन्फ़िगरेशन गाइड

THS1007CDA (rectangular gull-wing पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

THS1007CDA के लिए rectangular gull-wing पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: THS1007CDA.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

THS1007CDA के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Process Monitoring, Vibration and Condition Monitoring, Motor Drive Diagnostics, Communication Receiver Front End, Precision Instrumentation, Data Acquisition Systems.

🏭

Industrial Process Monitoring

The THS1007CDA suits multichannel industrial monitoring because it captures four analog signals simultaneously at a 6 MSPS conversion rate and resolves each channel to 10 bits. Place the four sensors on separate analog inputs and read complete frames through the parallel DSP or microprocessor interface. Simultaneous sampling prevents channel skew from being confused with real process timing, while automatic channel scanning can simplify repetitive acquisition sequences. The 4.75 V to 5.25 V supply requirement should be coordinated with sensor excitation, analog signal conditioning, and the downstream processor.

🏭

Vibration and Condition Monitoring

The THS1007CDA is well suited to simultaneous vibration measurement because four sensor channels can be sampled during each 6 MSPS conversion interval. This timing relationship helps engineers compare phase and amplitude between accelerometers mounted at different machine locations. The 10-bit resolution provides 1,024 digital codes per conversion, while the parallel interface supports efficient frame transfer into a DSP or microprocessor. Apply suitable input protection and analog filtering before the converter when machinery transients or out-of-band vibration content could exceed the intended input range.

⚡

Motor Drive Diagnostics

The THS1007CDA can acquire current, voltage, or position-related feedback from four channels at the same sampling instant for motor-drive diagnostics. Simultaneous sampling is valuable when the controller must compare phase relationships between feedback quantities rather than merely sample them one after another. A 6 MSPS rate and 10-bit resolution support rapid capture of transient behavior, while the parallel interface allows frames to be transferred efficiently to a control processor. The design must preserve signal integrity between the power stage, analog front end, converter, and digital control system.

🌐

Communication Receiver Front End

The THS1007CDA can form part of a communications receiver front end when four received or mixed analog channels require consistent timing. Its 10-bit conversion resolution and 6 MSPS sampling rate are appropriate for intermediate-frequency, envelope, or demodulation measurements where the selected bandwidth falls within the converter's acquisition capability. The parallel output supports direct processing by a DSP, while simultaneous sampling helps preserve relative phase between channels. Reference selection remains important because internal 1.5 V or 3.5 V references or an external reference affect DC accuracy and drift.

🔧

Precision Instrumentation

The THS1007CDA is appropriate for instruments that acquire several analog quantities, such as a sensor bridge, a reference measurement, a temperature channel, and a calibration signal. Four simultaneous samples make the resulting data easier to compare than a multiplexed sequence, and the 6 MSPS rate provides ample timing margin for many measurement systems. An external reference can be selected when calibration accuracy and temperature drift are more important than using the internal 1.5 V or 3.5 V references. Follow the manufacturer input-conditioning and acquisition-time guidance.

🖥️

Data Acquisition Systems

The THS1007CDA provides a compact four-channel acquisition section for a parallel-bus data-acquisition system. Each conversion produces simultaneous samples that can be stored and processed as a coherent frame, while the 6 MSPS rate supports higher throughput than many slow-resolution multiplexed converters. The 32-pin TSSOP package limits board area, and automatic channel scanning can assist repetitive operation. The parallel interface requires careful bus timing and signal-integrity layout, particularly when data lines connect to a processor operating at a different clock rate.

What is the THS1007CDA?
The THS1007CDA is a 10-bit, four-channel, 6 MSPS simultaneous-sampling ADC with a parallel DSP and microprocessor interface. According to the Texas Instruments THS1007 product documentation, it samples all four analog channels simultaneously, supports automatic channel scanning, and operates from a 4.75 V to 5.25 V supply. The device is packaged in a 32-pin TSSOP and is intended for multichannel acquisition, industrial measurement, communications, and instrumentation systems where relative timing between channels is important.
What are the key specifications of THS1007CDA that engineers should know?
The key THS1007CDA specifications are 10-bit resolution, four simultaneous analog inputs, a 6 MSPS conversion rate, and a parallel DSP or microprocessor output interface. The manufacturer specifies a 4.75 V to 5.25 V operating supply and internal reference voltages of 1.5 V and 3.5 V, with support for an external reference. The commercial THS1007C device is characterized from 0°C to 70°C. These parameters define its suitability for multichannel data acquisition and processor-controlled measurement systems.
What is the conversion speed of THS1007CDA?
The THS1007CDA converts at 6 MSPS, or 6 million samples per second. According to Texas Instruments, the four input channels are sampled simultaneously rather than sequentially through a multiplexer. This means each conversion frame contains measurements from all four channels that share the same sampling instant. The result is valuable for vibration analysis, phase measurement, motor monitoring, and other applications where a time offset between multiplexed channels would reduce measurement accuracy.
Why is simultaneous sampling important in THS1007CDA?
Simultaneous sampling is important because the THS1007CDA captures all four analog inputs during the same conversion interval. According to the Texas Instruments product documentation, this avoids the sequential timing offset that a multiplexed ADC can introduce between channels. Engineers can therefore compare phase, amplitude, and timing relationships across sensors more reliably. The benefit is especially clear in vibration diagnostics, balanced bridge measurements, and synchronized instrumentation where the physical events being measured are not naturally staggered.
What supply voltage does THS1007CDA require?
The THS1007CDA is specified for a 4.75 V to 5.25 V power-supply range. According to the Texas Instruments THS1007 documentation, this is a nominal 5 V analog operating environment. The input range leaves approximately 250 mV of margin below 5 V and above 4.75 V, allowing for supply variation and regulation error. Designers should also verify that the analog input range, reference voltage, and digital interface levels remain compatible with this supply requirement.
Does THS1007CDA have internal and external reference options?
Yes, the THS1007CDA provides internal reference voltages of 1.5 V and 3.5 V and can accept an external reference. According to the Texas Instruments comparison information for the THS1007 family, the internal references support general conversions, while an external reference lets the engineer select accuracy and temperature drift appropriate to the application. The external-reference approach is preferable when the measurement chain requires improved DC stability or calibration tied to a system reference.
Where can I find the THS1007CDA pinout and datasheet?
The THS1007CDA pinout and technical information can be found on the official Texas Instruments THS1007 product page and in the manufacturer datasheet linked from that page. The part uses a 32-pin TSSOP package, and the complete numbered pin-description table should be used when assigning signals or laying out the PCB. Use the pin table for power, analog inputs, reference connections, control signals, and the parallel digital bus rather than inferring functions from a generic TSSOP footprint.
Is THS1007CDA suitable for vibration and motor monitoring?
The THS1007CDA is suitable for vibration and motor monitoring when simultaneous channel timing is important. Its 10-bit resolution, four analog inputs, and 6 MSPS conversion rate allow multiple sensor signals to be captured during each conversion interval. According to Texas Instruments, simultaneous sampling avoids multiplexed-channel skew, making phase comparison between accelerometers or motor-feedback signals more useful. The parallel interface also permits efficient transfer of complete multichannel frames to a DSP or microprocessor.
Where can I buy THS1007CDA and check current availability?
The current price, stock position, and lead time for THS1007CDA should be requested through the Request a Quote form on this page. The form is the appropriate route for an exact-MPN quotation, including the 32-pin TSSOP package and commercial temperature grade. Request the production quantity and required delivery date when submitting the inquiry so that allocation and scheduling can be evaluated against the project schedule.
What is the price of THS1007CDA?
The THS1007CDA price depends on order quantity, packaging, and current component availability. Use the Request a Quote form on this page to obtain a current quotation for the exact THS1007CDA ordering code. Include the required quantity, target date, and shipment destination in the request. This avoids relying on an outdated historical price and ensures that the inquiry is evaluated against the exact 10-bit, four-channel, 32-pin TSSOP device requested.
What is the lead time for THS1007CDA?
The current THS1007CDA lead time is established through the Request a Quote form on this page. State the required quantity, production schedule, and shipment destination in the inquiry so the order can be evaluated for current manufacturing and allocation status. Engineers should also confirm whether the target assembly schedule permits an alternate sourcing path if the requested quantity cannot be delivered on the original project date.
What is the best drop-in replacement for THS1007CDA?
The best established drop-in replacement is the Texas Instruments THS1007IDA, which uses the same 32-pin TSSOP package and retains the 10-bit, 6 MSPS, four-channel simultaneous-sampling architecture. Its key difference is the temperature grade: the THS1007C family is characterized for 0°C to 70°C, while the THS1007I family is characterized for -40°C to 85°C. Because the industrial-grade part extends the operating range by 30°C at the cold end and 15°C at the hot end, verify timing, accuracy, and system-temperature requirements before substitution.
What can replace THS1007CDA?
The THS1007IDA is the clearest replacement candidate for THS1007CDA because it retains the same TSSOP-32 footprint, 10-bit resolution, four analog inputs, 6 MSPS rate, and simultaneous-sampling function. The main engineering change is its industrial temperature characterization of -40°C to 85°C versus 0°C to 70°C for the commercial THS1007C family. Confirm the complete pin arrangement, reference configuration, interface timing, and acquisition requirements in the manufacturer documentation before approving the substitution.
THS1007CDA vs THS1007IDA: which is better?
The THS1007IDA is better when the system must operate below 0°C or above 70°C because it is characterized from -40°C to 85°C. The THS1007CDA remains appropriate for a commercial-temperature design because its stated operating range is 0°C to 70°C. Both parts are identified as 10-bit, 6 MSPS, four-channel simultaneous-sampling converters in 32-pin TSSOP packages. The temperature grade, rather than conversion performance, is the primary decision point.
When should I choose THS1007CDA instead of THS1007IDA?
Choose the THS1007CDA when the product is intentionally limited to the commercial 0°C to 70°C range and an industrial-temperature grade would add unnecessary qualification or sourcing effort. The device retains the same 10-bit resolution, four simultaneous channels, 6 MSPS conversion rate, and 32-pin TSSOP package associated with the THS1007IDA. Confirm that no enclosure temperature, motor-cabinet environment, or manufacturing test condition can exceed the commercial-grade limits before selecting the THS1007CDA.

के लिए इंजीनियरिंग संदर्भ डेटा THS1007CDA — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose THS1007CDA for a commercial-temperature, four-channel simultaneous-sampling system where the enclosure will remain between 0°C and 70°C. Its 10-bit resolution, 6 MSPS conversion rate, and parallel DSP or microprocessor interface are appropriate for vibration analysis, process monitoring, communications measurement, and general-purpose data acquisition. Choose THS1007IDA when the same electrical architecture and TSSOP-32 footprint are needed across a wider -40°C to 85°C industrial range. Do not select a cross-brand replacement solely from the ADC type, resolution, and sampling rate; confirm the complete pinout, acquisition timing, reference configuration, control interface, and electrical limits in manufacturer documentation.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद THS1007IDA
Brand Texas Instruments Texas Instruments
Package TSSOP-32 TSSOP-32
Resolution 10 bit 10 bit
Conversion Rate 6 MSPS 6 MSPS
Analog Input Channels 4 channels 4 channels
Sampling Method Simultaneous sampling Simultaneous sampling
Operating Temperature 0°C to 70°C -40°C to 85°C
Power-Supply Voltage 4.75 V to 5.25 V 4.75 V to 5.25 V
Output Interface Parallel DSP/microprocessor interface Parallel DSP/microprocessor interface
Automatic Channel Scan Supported Supported

मुख्य विशेषताएँ

  • Maintains simultaneous four-channel sampling (बनामTHS1007IDA)
  • Commercial temperature characterization (बनामTHS1007IDA)
  • Parallel processor-oriented interface (बनामTHS1007IDA)

डिज़ाइन नोट्स

Route the parallel data bus with continuous references to ground and match its length where practical. Keep analog input traces away from the digital output bus, especially the clock and data lines that switch during acquisition. Place input filtering, reference decoupling, and analog circuitry close to the TSSOP-32 device. Use a solid ground plane and provide a low-impedance return for the converter rather than routing analog and digital return currents through a narrow shared path.

Check acquisition time, input bandwidth, source impedance, and conversion timing together; adequate resolution does not guarantee that a high-impedance sensor can charge the sampling network quickly enough. Add the recommended bypass capacitors at the supply and reference pins, and use an external reference when the measurement requires better DC accuracy or lower temperature drift than the internal 1.5 V and 3.5 V references provide.

Do not assume that identical functions guarantee identical timing on a mixed commercial and industrial design. The THS1007CDA and THS1007IDA are both described as 10-bit, 6 MSPS, four-channel simultaneous-sampling converters, but their temperature ranges differ. Before using THS1007IDA as a drop-in replacement, verify the complete pin assignments, reference behavior, control timing, acquisition sequence, and worst-case performance in the manufacturer documentation.

The TSSOP-32 package dissipates converter power as a function of supply voltage, conversion activity, digital output loading, and ambient temperature. Evaluate the operating temperature against the commercial 0°C to 70°C limit for THS1007C or the industrial -40°C to 85°C range for THS1007IDA. Provide sensible copper around the package and avoid placing the converter next to a heat source that pushes the junction temperature beyond the device rating.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance status requires confirmation from the manufacturer product page or current declaration documents.

डेटा सत्यापन तिथि: 2026-11-16 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

THS1007CDA datasheet THS1007CDA pinout THS1007CDA datasheet pdf THS1007CDA equivalent THS1007CDA replacement THS1007CDA vs THS1007IDA THS1007CDA TSSOP-32 pinout THS1007CDA application circuit THS1007CDA price THS1007CDA stock Texas Instruments THS1007CDA THS1007 10-bit 6 MSPS ADC

संबंधित कंपोनेंट्स और शब्द

Texas Instruments THS1007CDA THS1007IDA analog-to-digital converter ADC data-converter IC semiconductor 10-bit ADC 6 MSPS four-channel ADC simultaneous sampling parallel DSP interface microprocessor interface pipelined ADC automatic channel scan internal reference voltage external reference voltage TSSOP-32 surface-mount package industrial process monitoring vibration monitoring motor-drive diagnostics data-acquisition system RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें