Texas Instruments

TLV2370IP - 3MHz RRIO Op Amp | Texas Instruments | Signal

MPN: TLV2370IP ✓ सक्रिय
550 µA per channel Vdss PDIP-8 Package
न्यूनतम ऑर्डर मात्रा: 1 |

TLV2370IP अवलोकन

The Texas Instruments TLV2370IP is a single operational amplifier with rail-to-rail input and output capability, 3 MHz gain-bandwidth product, 550 µA per-channel supply current, and shutdown support, housed in an 8-pin PDIP package. It operates from a minimum supply voltage of 2.7 V, while the maximum recommended supply voltage is 16 V.

An operational amplifier is an analog signal-conditioning IC that compares an input voltage with a feedback-defined reference and amplifies the difference. The TLV2370 belongs to the rail-to-rail input and output operational amplifier family, combining low-power operation with broad input and output swing. This places it within the operational amplifier, analog amplifier, and signal-conditioning semiconductor hierarchy.

The principal features include 3 MHz bandwidth, approximately 550 µA of supply current per channel, operation down to 2.7 V, and rail-to-rail input and output operation. The shutdown function allows the amplifier to be disabled when it is not needed, helping reduce system power in intermittently active equipment. The device is available in the TLV2370IP PDIP-8 configuration for through-hole industrial and instrumentation designs.

Its low-power operating current is particularly useful in battery-powered measurement systems where a conventional higher-speed amplifier would increase continuous energy use. The 3 MHz bandwidth provides sufficient response for general-purpose signal amplification, impedance buffering, filtering, and sensor-interface circuits. The 2.7 V minimum operating supply also supports low-voltage systems that cannot provide the higher rails associated with older precision op amps.

Typical uses include portable instrumentation, industrial sensor conditioning, low-voltage data acquisition, audio signal paths, and embedded control systems. The amplifier can operate from a single positive supply while accepting input and output signals that approach the available rail voltages. Its shutdown pin provides an additional mechanism for controlled power management in multichannel or duty-cycled systems.

PCB design should preserve short feedback paths, place input and feedback components close to the relevant pins, and route high-impedance input nodes away from switching nodes. Because the device supports shutdown, the shutdown control must be driven to the correct logic level during normal operation. Review the manufacturer pin-description and application information before assigning PCB tracks.

This page combines manufacturer specifications, application guidance, drop-in replacement information, and practical PCB considerations to support faster component evaluation and board-level design decisions.

के लिए ड्रॉप-इन विकल्प TLV2370IP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

TLV9151IP

✅ ड्रॉप-इन
📦 PDIP-8
Shutdown polarity is opposite: TLV9151 is enabled low or floating, while TLV2370 is enabled high or floating; footprint is pin-to-pin

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2370IPG4

✅ ड्रॉप-इन
📦 PDIP-8
Same TLV2370IP electrical configuration and PDIP-8 footprint; ordering-code finish or grade designation differs

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2370IPE4

✅ ड्रॉप-इन
📦 PDIP-8
Same TLV2370IP electrical configuration and PDIP-8 footprint; ordering-code finish or grade designation differs

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2370IP Maximum Ratings और Electrical Characteristics

Number of Channels 1 channel
Amplifier Type Single operational amplifier
Gain-Bandwidth Product 3 MHz
सप्लाई करंट 550 µA per channel
Minimum Operating Supply Voltage 2.7 V
Maximum Recommended Supply Voltage 16 V
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Shutdown Support Yes
ऑपरेटिंग तापमान रेंज Extended industrial range
पैकेज PDIP-8
पिन की संख्या 8 pins
माउंटिंग प्रकार Through-hole
Product Category Standard general-purpose amplifier
RoHS स्थिति Compliant
लाइफसाइकिल स्थिति Active
Lead Finish Lead-free

TLV2370IP pdip-8 पिन कॉन्फ़िगरेशन गाइड

TLV2370IP (pdip-8 पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

TLV2370IP के लिए pdip-8 पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: TLV2370IP.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

TLV2370IP के लिए उपयुक्त है 6 अनुप्रयोगs: Portable Sensor Conditioning, Industrial Data Acquisition, Low-Voltage Audio Buffering, Battery-Powered Monitoring, Precision Signal Buffering, Embedded Control Interfaces.

📱

Portable Sensor Conditioning

The TLV2370IP fits portable sensor-conditioning circuits that require rail-to-rail input and output from a single low-voltage supply. Its approximately 550 µA supply current reduces continuous energy use compared with a conventional higher-current amplifier, while the 3 MHz gain-bandwidth product provides useful bandwidth for filtering and gain stages around resistive or bridge sensors. The device can be placed directly between the sensor network and an analog-to-digital converter. Care should be taken to keep high-impedance input traces short, use a stable reference near the input pins, and avoid routing them beside switching nodes.

🏭

Industrial Data Acquisition

The TLV2370IP is appropriate for industrial data-acquisition modules operating from a 2.7 V or higher single supply. Rail-to-rail input and output expand the usable signal range in compact analog front ends, and the 3 MHz bandwidth is suitable for general-purpose measurement amplification rather than very high-frequency instrumentation. The amplifier may drive an ADC input or serve as a buffer between a conditioning network and the converter. Layout should provide a low-impedance return path, minimize input-loop area, and account for the shutdown-control state during power management.

🎧

Low-Voltage Audio Buffering

The TLV2370IP can be used as a low-power audio buffer or line-stage amplifier in portable and compact audio systems. Rail-to-rail input and output are valuable when the signal operates near the lower supply limit, while approximately 550 µA supply current helps control consumption. The 3 MHz gain-bandwidth product provides more bandwidth than required for many audio paths, although actual distortion and stability depend on the selected gain, load, and output-coupling arrangement. Designers should verify capacitive-load behavior and place the output network close to the amplifier pins.

🧩

Battery-Powered Monitoring

The TLV2370IP supports battery-powered monitoring systems because it operates from 2.7 V and consumes approximately 550 µA per channel. Those characteristics make it useful for amplifying sensor signals in wearable, remote, or intermittent-duty-cycle equipment. The shutdown function allows the amplifier to remain disabled between measurement events, reducing system activity when continuous operation is unnecessary. A practical design should include defined shutdown levels, local input filtering, and a common-ground layout that prevents injected current from disturbing the sensor reference.

🔧

Precision Signal Buffering

The TLV2370IP can buffer high-impedance sources in instrumentation circuits where the 3 MHz bandwidth and rail-to-rail output are more important than very low offset specifications. Typical uses include impedance isolation between sensor networks and downstream converters, as well as active filtering in test equipment. The low 550 µA-class operating current also makes the amplifier suitable for distributed measurement channels. Designers should preserve the datasheet-recommended feedback topology, check output swing at the required load, and avoid excessive capacitance directly on the output node.

⚡

Embedded Control Interfaces

The TLV2370IP is useful in embedded control systems for scaling sensor, current, or logic-level signals before they reach an ADC or comparator. Its single-rail operation from 2.7 V simplifies interfacing with low-voltage controllers, and the shutdown input can support inactive operating states. The 3 MHz bandwidth provides ample response for many control loops, but closed-loop gain and stability must be selected with the actual feedback network and load. Keep sensitive analog traces away from processor supply returns and switching inductors to avoid common-mode disturbance.

What is the key specification of the TLV2370IP operational amplifier?
The TLV2370IP is a single, low-power operational amplifier with a 3 MHz gain-bandwidth product, approximately 550 µA of supply current per channel, and rail-to-rail input and output operation. According to the Texas Instruments TLV2370 product information, the amplifier operates from a minimum supply voltage of 2.7 V and supports supply voltages up to the 16 V maximum recommended level. It is offered in the TLV2370IP configuration in an 8-pin PDIP package for through-hole instrumentation and general-purpose analog designs.
What is the operating voltage range of the TLV2370IP?
The TLV2370IP operates from a minimum supply voltage of 2.7 V, and its maximum recommended supply voltage is 16 V. According to the Texas Instruments TLV2370 product information, the 2.7 V minimum supports low-voltage, single-supply systems, while the 16 V upper recommendation covers conventional industrial and instrumentation supply rails. Designers should maintain the supply within the manufacturer limits and include adequate input and output range analysis for the actual circuit.
Does the TLV2370IP have rail-to-rail input and output?
Yes, the TLV2370IP provides rail-to-rail input and output operation. The Texas Instruments TLV2370 product page identifies the device as an RRIO amplifier, meaning its input common-mode range and output swing extend toward the supply rails. This capability is useful in low-voltage, single-supply designs where conventional non-rail-to-rail amplifiers would restrict usable signal range. Actual input and output limits vary slightly from the ideal rails, so headroom should still be checked against the required signal excursion.
Why choose the TLV2370IP for a low-power design?
The TLV2370IP is suitable for low-power designs because it combines a 3 MHz gain-bandwidth product with approximately 550 µA of supply current per channel. According to the Texas Instruments TLV2370 product information, this operating point provides useful bandwidth for general-purpose amplification while limiting continuous supply demand. Its shutdown function can further reduce consumption when the amplifier is not required. The combination is well suited to portable instrumentation, sensor interfaces, and low-voltage embedded measurement systems.
Where can I download the TLV2370IP datasheet PDF?
The official TLV2370 datasheet can be downloaded from the Texas Instruments product page at https://www.ti.com/lit/gpn/TLV2370. The manufacturer page identifies the TLV2370IP as the 8-pin PDIP ordering option for the single amplifier with shutdown. Use the manufacturer pin-description table and electrical-characteristics tables when assigning pins, setting gain, and confirming operating limits. A compatible comparison listing is also available, but the manufacturer datasheet should remain the controlling design document.
Where can I find the TLV2370IP pinout?
The TLV2370IP pinout is found in the pin-configuration section of the Texas Instruments TLV2370 datasheet, available at https://www.ti.com/lit/gpn/TLV2370. The TLV2370IP uses an 8-pin PDIP outline, and its shutdown-control connection must be checked carefully during PCB design. Follow the package drawing and pin-description table when assigning the socket or through-hole footprint. The manufacturer document should be used to confirm every signal and supply pin rather than relying on a generic 8-pin operational-amplifier drawing.
What can replace the TLV2370IP?
The TLV9151 is identified by Texas Instruments as a pin-to-pin upgrade candidate for the TLV2370, but its shutdown polarity is opposite and the board must be checked before direct substitution. Texas Instruments support material states that the TLV2370 shutdown pin is pulled high or left floating, while the TLV9151 shutdown pin is pulled low or left floating. A TLV2370IP board therefore needs logical verification, and any change should be reviewed against the complete signal path and operating requirements before production use.
Is the TLV9151IP the same as the TLV2370IP?
The TLV9151IP is not functionally identical to the TLV2370IP because the shutdown-control polarity differs. Texas Instruments support material describes the TLV9151 as a pin-to-pin upgrade for the TLV2370, but it specifies that the TLV2370 is enabled by a high or floating shutdown pin whereas the TLV9151 is enabled by a low or floating shutdown pin. Systems that do not actively control shutdown may proceed more readily, while systems with fixed shutdown logic require a deliberate polarity review.
TLV2370IP vs TLV9151IP: which is better for a shutdown-controlled circuit?
Choose the TLV2370IP when the existing circuit expects shutdown to be active-high, and evaluate the TLV9151IP when its opposite shutdown polarity matches the design. Texas Instruments support information identifies the TLV9151 as a pin-to-pin upgrade candidate but explicitly notes the reversed shutdown logic. Both are associated with the TLV2370/TLV9151 amplifier families and low-voltage rail-to-rail operation. The decisive issue is therefore the shutdown-control state, not a change to the physical 8-pin footprint.
When should I choose the TLV2370IP over another pin-compatible amplifier?
Choose the TLV2370IP when the circuit needs one amplifier with approximately 550 µA supply current, 3 MHz bandwidth, rail-to-rail input and output, and shutdown control in an 8-pin PDIP package. It is particularly appropriate for low-voltage instrumentation and industrial measurement circuits that use a through-hole footprint. Compared with a general-purpose amplifier without shutdown, its dedicated shutdown function can simplify duty-cycled power control. Before selecting it, verify that 3 MHz bandwidth is sufficient for the required closed-loop response and settling behavior.
Is the TLV2370IP suitable for sensor and data-acquisition applications?
Yes, the TLV2370IP is suitable for low-voltage sensor and data-acquisition front ends that require rail-to-rail input and output, a 3 MHz gain-bandwidth product, and low supply current. Its approximately 550 µA operating current helps limit power in portable or distributed measurement systems. The 2.7 V minimum supply supports single-rail operation, while the shutdown function can disable the amplifier between measurements. High-impedance sensor layouts still require short traces, guarding, and careful separation from switching or digital return paths.
Where can I buy TLV2370IP online and check its price?
Use the Request a Quote form on this page to request current TLV2370IP pricing, stock status, lead time, and order quantity. The form provides a direct response for the exact TLV2370IP ordering option rather than requiring a search across multiple listings. For engineering confirmation, use the Texas Instruments TLV2370 product page at https://www.ti.com/product/TLV2370. Share the required quantity, delivery location, and packaging preference when requesting a quotation.
What is the lead time for TLV2370IP?
The current lead time for TLV2370IP should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, factory inventory, and fulfillment conditions, so an older listing is not a reliable commitment. Submit the required quantity and delivery destination to obtain a current quotation. Texas Instruments lists the TLV2370 family as active, which indicates product availability for new designs.
Is TLV2370IP in stock?
Current TLV2370IP inventory should be checked through the Request a Quote form on this page. The form accepts the requested quantity and returns the latest supply information for the exact PDIP-8 ordering code. Texas Instruments identifies the TLV2370 family as active, but family lifecycle status does not by itself guarantee a particular stock quantity at every authorized channel. Use the quotation response for production planning and component scheduling.
What is the best cross-brand equivalent for TLV2370IP?
No cross-brand drop-in equivalent can be confirmed from the available manufacturer and cross-reference information. A valid equivalent must match the 8-pin PDIP footprint, pin functions, shutdown behavior, supply range, bandwidth, and current draw rather than merely share the same amplifier category. The documented TLV9151 replacement relationship is from Texas Instruments, so it is not a cross-brand option. Board designers should require a manufacturer-confirmed pin and parameter match before treating any third-party amplifier as a drop-in replacement.

के लिए इंजीनियरिंग संदर्भ डेटा TLV2370IP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TLV2370IP for a low-voltage, single-amplifier design that requires rail-to-rail input and output, approximately 550 µA operating current, 3 MHz bandwidth, and an 8-pin PDIP footprint. It is particularly suitable for portable instrumentation, industrial data acquisition, sensor buffering, and embedded analog interfaces. Select TLV2370IPG4 or TLV2370IPE4 when the purchasing organization specifically requires the corresponding ordering designation while retaining the same identified TLV2370 configuration. Evaluate the TLV9151IP only after checking its reversed shutdown polarity; it may be attractive as a pin-to-pin upgrade, but an existing high-or-floating shutdown control will not behave identically. For designs requiring more precision, lower offset, faster settling, a different supply range, or a different package, perform a full electrical review instead of assuming amplifier-category equivalence.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TLV9151IP TLV2370IPG4 TLV2370IPE4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package PDIP-8 PDIP-8 PDIP-8 PDIP-8
Amplifier Configuration Single operational amplifier Single operational amplifier Single operational amplifier Single operational amplifier
Shutdown Control Enabled high or floating Enabled low or floating; opposite shutdown polarity Enabled high or floating Enabled high or floating

मुख्य विशेषताएँ

  • Combines low-power operation with useful signal bandwidth (बनामTLV9151IP)
  • Uses a straightforward through-hole 8-pin PDIP footprint (बनामTLV2370IPG4)
  • Supports direct low-voltage single-supply operation (बनामTLV2370IPE4)

डिज़ाइन नोट्स

Keep the op-amp feedback components and sensitive input traces close to the corresponding pins, and avoid routing input or feedback paths alongside switching-node copper. For high-impedance sensors, use a quiet ground reference and consider a grounded guard where practical. A compact layout reduces parasitic capacitance, radiated pickup, and feedback-loop area, all of which can affect signal integrity in low-current analog systems.

Place the supply bypass capacitor close to the positive and ground pins, and route the return directly to the device ground without sharing a narrow path with motor, relay, or digital-switching return currents. Although the amplifier consumes approximately 550 µA per channel, transient load current and switching noise from nearby circuits can still disturb its output. Validate the capacitor value and stability behavior against the manufacturer guidance for the selected gain and load.

Verify the shutdown logic before substituting a similar amplifier. Texas Instruments identifies the TLV9151 as a pin-to-pin upgrade candidate for the TLV2370 but states that the shutdown polarity is reversed. Pulling the wrong logic state may disable the amplifier unexpectedly or prevent intended low-power operation. Also confirm the required output swing and input common-mode range; rail-to-rail operation does not imply perfect saturation at either supply rail.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Yes
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The available component comparison identifies the TLV2370IP as RoHS compliant and lead-free. Other environmental declarations are not established by the cited manufacturer information.

डेटा सत्यापन तिथि: 2026-11-15 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

TLV2370IP datasheet TLV2370IP pinout TLV2370IP datasheet pdf TLV2370IP specifications TLV2370IP replacement TLV2370IP equivalent TLV2370IP vs TLV9151IP TLV2370IP PDIP-8 Texas Instruments TLV2370IP TLV2370IP price TLV2370IP stock TLV2370IP application circuit

संबंधित कंपोनेंट्स और शब्द

Texas Instruments TLV2370IP TLV9151IP TLV2370IPG4 TLV2370IPE4 Operational Amplifier Single Operational Amplifier Rail-to-Rail Input and Output Amplifier RRIO Amplifier Analog Signal Conditioning Voltage Feedback Amplifier Semiconductor PDIP-8 DIP Package Family Through-Hole Package 3 MHz Gain-Bandwidth Product 550 µA Supply Current 2.7 V Minimum Supply Voltage 16 V Maximum Recommended Supply Voltage Shutdown Control Sensor Interface Data Acquisition Portable Instrumentation RoHS
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें