TLV2370IP - 3MHz RRIO Op Amp | Texas Instruments | Signal
部品番号: TLV2370IP ✓ 生産中TLV2370IP 概要
An operational amplifier is an analog signal-conditioning IC that compares an input voltage with a feedback-defined reference and amplifies the difference. The TLV2370 belongs to the rail-to-rail input and output operational amplifier family, combining low-power operation with broad input and output swing. This places it within the operational amplifier, analog amplifier, and signal-conditioning semiconductor hierarchy.
The principal features include 3 MHz bandwidth, approximately 550 µA of supply current per channel, operation down to 2.7 V, and rail-to-rail input and output operation. The shutdown function allows the amplifier to be disabled when it is not needed, helping reduce system power in intermittently active equipment. The device is available in the TLV2370IP PDIP-8 configuration for through-hole industrial and instrumentation designs.
Its low-power operating current is particularly useful in battery-powered measurement systems where a conventional higher-speed amplifier would increase continuous energy use. The 3 MHz bandwidth provides sufficient response for general-purpose signal amplification, impedance buffering, filtering, and sensor-interface circuits. The 2.7 V minimum operating supply also supports low-voltage systems that cannot provide the higher rails associated with older precision op amps.
Typical uses include portable instrumentation, industrial sensor conditioning, low-voltage data acquisition, audio signal paths, and embedded control systems. The amplifier can operate from a single positive supply while accepting input and output signals that approach the available rail voltages. Its shutdown pin provides an additional mechanism for controlled power management in multichannel or duty-cycled systems.
PCB design should preserve short feedback paths, place input and feedback components close to the relevant pins, and route high-impedance input nodes away from switching nodes. Because the device supports shutdown, the shutdown control must be driven to the correct logic level during normal operation. Review the manufacturer pin-description and application information before assigning PCB tracks.
This page combines manufacturer specifications, application guidance, drop-in replacement information, and practical PCB considerations to support faster component evaluation and board-level design decisions.
ドロップイン代替品: TLV2370IP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
TLV9151IP
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2370IPG4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2370IPE4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2370IP 最大定格&電気的特性
| Number of Channels | 1 channel |
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 3 MHz |
| 電源電流 | 550 µA per channel |
| Minimum Operating Supply Voltage | 2.7 V |
| Maximum Recommended Supply Voltage | 16 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Support | Yes |
| 動作温度範囲 | Extended industrial range |
| パッケージ | PDIP-8 |
| ピン数 | 8 pins |
| 実装タイプ | Through-hole |
| Product Category | Standard general-purpose amplifier |
| RoHS ステータス | Compliant |
| ライフサイクル状態 | Active |
| Lead Finish | Lead-free |
TLV2370IP pdip-8 ピン配置ガイド
TLV2370IP (pdip-8 パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2370IP.
詳細は データシート をご参照ください。
主な用途
TLV2370IP の用途: 6 件s: Portable Sensor Conditioning, Industrial Data Acquisition, Low-Voltage Audio Buffering, Battery-Powered Monitoring, Precision Signal Buffering, Embedded Control Interfaces.
Portable Sensor Conditioning
The TLV2370IP fits portable sensor-conditioning circuits that require rail-to-rail input and output from a single low-voltage supply. Its approximately 550 µA supply current reduces continuous energy use compared with a conventional higher-current amplifier, while the 3 MHz gain-bandwidth product provides useful bandwidth for filtering and gain stages around resistive or bridge sensors. The device can be placed directly between the sensor network and an analog-to-digital converter. Care should be taken to keep high-impedance input traces short, use a stable reference near the input pins, and avoid routing them beside switching nodes.
おすすめ
Industrial Data Acquisition
The TLV2370IP is appropriate for industrial data-acquisition modules operating from a 2.7 V or higher single supply. Rail-to-rail input and output expand the usable signal range in compact analog front ends, and the 3 MHz bandwidth is suitable for general-purpose measurement amplification rather than very high-frequency instrumentation. The amplifier may drive an ADC input or serve as a buffer between a conditioning network and the converter. Layout should provide a low-impedance return path, minimize input-loop area, and account for the shutdown-control state during power management.
おすすめ
Low-Voltage Audio Buffering
The TLV2370IP can be used as a low-power audio buffer or line-stage amplifier in portable and compact audio systems. Rail-to-rail input and output are valuable when the signal operates near the lower supply limit, while approximately 550 µA supply current helps control consumption. The 3 MHz gain-bandwidth product provides more bandwidth than required for many audio paths, although actual distortion and stability depend on the selected gain, load, and output-coupling arrangement. Designers should verify capacitive-load behavior and place the output network close to the amplifier pins.
おすすめ
Battery-Powered Monitoring
The TLV2370IP supports battery-powered monitoring systems because it operates from 2.7 V and consumes approximately 550 µA per channel. Those characteristics make it useful for amplifying sensor signals in wearable, remote, or intermittent-duty-cycle equipment. The shutdown function allows the amplifier to remain disabled between measurement events, reducing system activity when continuous operation is unnecessary. A practical design should include defined shutdown levels, local input filtering, and a common-ground layout that prevents injected current from disturbing the sensor reference.
おすすめ
Precision Signal Buffering
The TLV2370IP can buffer high-impedance sources in instrumentation circuits where the 3 MHz bandwidth and rail-to-rail output are more important than very low offset specifications. Typical uses include impedance isolation between sensor networks and downstream converters, as well as active filtering in test equipment. The low 550 µA-class operating current also makes the amplifier suitable for distributed measurement channels. Designers should preserve the datasheet-recommended feedback topology, check output swing at the required load, and avoid excessive capacitance directly on the output node.
おすすめ
Embedded Control Interfaces
The TLV2370IP is useful in embedded control systems for scaling sensor, current, or logic-level signals before they reach an ADC or comparator. Its single-rail operation from 2.7 V simplifies interfacing with low-voltage controllers, and the shutdown input can support inactive operating states. The 3 MHz bandwidth provides ample response for many control loops, but closed-loop gain and stability must be selected with the actual feedback network and load. Keep sensitive analog traces away from processor supply returns and switching inductors to avoid common-mode disturbance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV2370IP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV9151IP | TLV2370IPG4 | TLV2370IPE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Amplifier Configuration | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Shutdown Control | Enabled high or floating | Enabled low or floating; opposite shutdown polarity | Enabled high or floating | Enabled high or floating |
主な差別化要因
- Combines low-power operation with useful signal bandwidth (vs TLV9151IP)
- Uses a straightforward through-hole 8-pin PDIP footprint (vs TLV2370IPG4)
- Supports direct low-voltage single-supply operation (vs TLV2370IPE4)
設計ノート
Keep the op-amp feedback components and sensitive input traces close to the corresponding pins, and avoid routing input or feedback paths alongside switching-node copper. For high-impedance sensors, use a quiet ground reference and consider a grounded guard where practical. A compact layout reduces parasitic capacitance, radiated pickup, and feedback-loop area, all of which can affect signal integrity in low-current analog systems.
Place the supply bypass capacitor close to the positive and ground pins, and route the return directly to the device ground without sharing a narrow path with motor, relay, or digital-switching return currents. Although the amplifier consumes approximately 550 µA per channel, transient load current and switching noise from nearby circuits can still disturb its output. Validate the capacitor value and stability behavior against the manufacturer guidance for the selected gain and load.
Verify the shutdown logic before substituting a similar amplifier. Texas Instruments identifies the TLV9151 as a pin-to-pin upgrade candidate for the TLV2370 but states that the shutdown polarity is reversed. Pulling the wrong logic state may disable the amplifier unexpectedly or prevent intended low-power operation. Also confirm the required output swing and input common-mode range; rail-to-rail operation does not imply perfect saturation at either supply rail.
コンプライアンス情報
The available component comparison identifies the TLV2370IP as RoHS compliant and lead-free. Other environmental declarations are not established by the cited manufacturer information.