TLV2461IP - 6V RRIO 6.4MHz Op Amp | Texas Instruments
MPN: TLV2461IP ✓ सक्रियTLV2461IP अवलोकन
A rail-to-rail input/output operational amplifier is an analog signal-conditioning IC whose input common-mode range and output swing extend toward the positive and negative supply rails. This capability is useful when a signal approaches either supply limit, where a conventional fixed-range amplifier would clip or become nonlinear. Within the broader hierarchy, the TLV2461IP is an operational amplifier, an analog amplifier IC, and a semiconductor for low-voltage power management and signal processing.
The principal device characteristics are a 6 V supply rating, 6.4 MHz gain-bandwidth product, and rail-to-rail input/output operation. The single-amplifier configuration supports space-efficient designs where one analog channel is sufficient. Its 8-PDIP construction also facilitates prototyping, educational circuits, and through-hole industrial assemblies where surface-mount rework would be inconvenient.
The TLV2461 family targets portable and low-voltage applications where rail-to-rail signal handling is important. According to the Texas Instruments TLV2461 product information, the device is specified as a single 6 V, 6.4 MHz RRIO operational amplifier. Its architecture places the amplifier in the signal-conditioning hierarchy between a sensor or source and an ADC, transducer driver, or analog processing stage. Exact current, noise, offset, and temperature specifications should be confirmed in the manufacturer datasheet for the selected operating conditions.
Typical uses include portable measurement systems, battery-powered sensor interfaces, low-voltage audio paths, industrial controls, and general-purpose analog filtering. In a sensor-conditioning circuit, the amplifier can accept signals near the supply rails while presenting low-versus-high input impedance to the source. In an active filter or level-shifting stage, rail-to-rail output behavior can reduce clipping when the calculated output approaches the available supply range.
Designers should review the pin-description table, recommended operating conditions, electrical characteristics, and application information in the manufacturer datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be handled according to the datasheet guidance rather than left floating when the configuration permits it.
This page combines the TLV2461IP device identity, package information, verified manufacturer and distributor references, application guidance, and same-footprint alternatives into a focused engineering selection resource. It helps buyers evaluate the TLV2461IP for the Texas Instruments TLV2461 6 V RRIO operational-amplifier family while keeping board-level compatibility and application fit in view.
के लिए ड्रॉप-इन विकल्प TLV2461IP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं TLV2461IP (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Input Common-Mode Range, Output Swing.
TLV2461AIP
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV2461CP
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TLV2461CPE4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV2461IP Maximum Ratings और Electrical Characteristics
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Rating | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| पैकेज | 8-PDIP |
| पिन काउंट | 8 pins |
| माउंटिंग प्रकार | Through-hole |
TLV2461IP पिन कॉन्फ़िगरेशन
| पिन 1 | NC — Not connected |
| पिन 2 | IN- — Inverting input |
| पिन 3 | IN+ — Non-inverting input |
| पिन 4 | V- — Negative supply connection |
| पिन 5 | NC — Not connected |
| पिन 6 | SHDN — Shutdown input |
| पिन 7 | V+ — Positive supply connection |
| पिन 8 | OUT — Output |
सामान्य अनुप्रयोग
TLV2461IP के लिए उपयुक्त है 6 अनुप्रयोगs: Portable Sensor Signal Conditioning, Portable Audio Output Stage, Low-Voltage Active Filter, Industrial Control Signal Amplifier, Battery-Powered Data Acquisition, Test and Measurement Buffer.
Portable Sensor Signal Conditioning
The TLV2461IP fits low-voltage sensor interfaces that operate close to the available supply range. Its 6 V supply rating suits compact single-supply systems, while rail-to-rail input operation allows the amplifier to monitor sensor outputs that would otherwise approach the positive or negative rail. The 6.4 MHz gain-bandwidth product provides useful bandwidth for filtering and gain stages, although source impedance and input-bias-current requirements should be checked before selecting the amplifier. Place the device close to the sensor interface, keep the input route short, and provide local supply bypassing. The practical benefit is improved signal utilization in battery-powered equipment, where leaving several volts of input range unused would reduce usable measurement span.
अनुशंसित
Portable Audio Output Stage
The TLV2461IP can support low-voltage audio and communication output stages where the signal must remain usable near the supply limits. Its 6 V maximum supply classification and rail-to-rail output design can reduce clipping in compact headphone, line-level, or signal-buffer circuits when the calculated waveform approaches the available output range. The 6.4 MHz gain-bandwidth product is substantially higher than the audio-band signal, allowing closed-loop gain to be set without placing the amplifier near its bandwidth limit. The design should still account for output-load limits, gain error, and the frequency response shown in the manufacturer datasheet.
अनुशंसित
Low-Voltage Active Filter
The TLV2461IP is appropriate for first-order or higher-order active-filter stages operating from a 6 V-class supply. Its 6.4 MHz gain-bandwidth product provides bandwidth relative to many low-frequency measurement, control, and audio-filter requirements, while rail-to-rail input and output behavior helps preserve signal range in low-voltage systems. Component tolerances and the amplifier's gain-bandwidth response will shape the filter response, so simulated results should be checked against the datasheet limits. Keep feedback components close to the amplifier and route the input and output away from high-current switching paths.
अनुशंसित
Industrial Control Signal Amplifier
The TLV2461IP can amplify low-level control signals in compact industrial electronics when the analog node operates within a 6 V supply. Rail-to-rail inputs help accept controller outputs and sensor signals close to the supply boundary, while the 6.4 MHz gain-bandwidth product provides adequate bandwidth for many slow control loops and diagnostic waveforms. The single-amplifier 8-PDIP package reduces analog channel count compared with a dual or quad device. Engineers should verify offset, common-mode behavior, output drive, and noise against the specific transducer or controller before production release.
अनुशंसित
Battery-Powered Data Acquisition
The TLV2461IP is useful in battery-powered data-acquisition front ends that require signal amplification close to the available supply rail. The rail-to-rail input stage maximizes the measurable span of a 6 V-class system, while the 6.4 MHz gain-bandwidth product can accommodate acquisition signals well above a slow sensor-control bandwidth. For an ADC interface, choose the closed-loop gain and settling behavior according to the manufacturer data, then verify that the output swing leaves sufficient margin for the converter input range. Short traces, stable reference grounding, and local decoupling are especially important in compact mixed-signal equipment.
अनुशंसित
Test and Measurement Buffer
The TLV2461IP can buffer low-level signals in compact test and measurement equipment that operates from a low-voltage supply. Rail-to-rail input behavior reduces headroom loss when probing or conditioning signals near the rails, and the 6.4 MHz gain-bandwidth product supports higher-bandwidth measurement paths than a basic precision dc amplifier. The 8-PDIP package is convenient for instrument prototypes and through-hole control boards. For accurate measurements, evaluate input bias current, offset, noise, and output-loading behavior against the source and instrument architecture, and maintain a symmetrical ground reference around the measurement path.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा TLV2461IP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | TLV2461AIP | TLV2461CP | TLV2461CPE4 |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Amplifier Type | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Supply Voltage Rating | 6 V | 6 V | 6 V | 6 V |
| Gain-Bandwidth Product | 6.4 MHz | 6.4 MHz | 6.4 MHz | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
मुख्य विशेषताएँ
- Combines a 6 V supply rating with a 6.4 MHz gain-bandwidth product (बनामTLV2461CP)
- Provides the same 8-PDIP footprint and 6 V operating class (बनामTLV2461AIP)
- Retains single-amplifier rail-to-rail input/output operation (बनामTLV2461CPE4)
डिज़ाइन नोट्स
Place the power-supply bypass capacitor immediately adjacent to the V+ and V- pins, and keep the amplifier input, feedback, and output traces away from switching-node and high-current return paths. The 8-PDIP footprint provides generous physical spacing, but trace geometry still matters because input capacitance and coupled current can affect a rail-to-rail amplifier's noise and stability. Use a common ground reference for input and output when handling bipolar or single-supply signals.
Do not interpret the 6 V rating as permission to operate from an unrestricted supply. Check the complete recommended operating conditions, absolute maximum ratings, input common-mode range, and output-swing limits in the manufacturer datasheet. Rail-to-rail inputs and outputs reduce headroom requirements but do not eliminate the need to preserve voltage margin for offset, load current, temperature, and transient behavior.
For sensor and active-filter circuits, keep high-impedance input routes short and minimize parasitic capacitance on IN+ and IN-. If the source impedance is high, calculate the bias-current and thermal-noise contribution before choosing the gain. Feedback components should be positioned close to the amplifier, and the output should be isolated from capacitive loads unless the stability requirements for that load have been verified.
Treat the V+ and V- pins as a single-supply or dual-supply implementation according to the manufacturer instructions, but do not connect either rail outside the stated operating limits. Verify the amplifier's supply-current requirement and the temperature rise associated with the selected package under worst-case load. Local decoupling helps control supply impedance, while a stable, low-impedance ground reference prevents output disturbance from appearing as input noise.
अनुपालन जानकारी
The TLV2461IP is a general-purpose commercial operational amplifier; the documented product information does not identify an automotive qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact orderable suffix and current manufacturer declarations.