TLV2635IN - Quad 9MHz Rail-to-Rail Op Amp | Texas Instruments
MPN: TLV2635IN ✓ सक्रियTLV2635IN अवलोकन
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2635 belongs to the operational amplifier hierarchy and provides four independent amplifier channels in one package. Its rail-to-rail output allows the output voltage to approach the supply limits, making it useful for low-voltage instrumentation and signal-conditioning systems.
The principal features of the TLV2635IN include four amplifier circuits, a 9 MHz gain-bandwidth product, approximately 730 uA of supply current per channel, and operation from a single supply. The common-mode input range includes ground, while the output stage supports rail-to-rail operation. These characteristics support accurate signal conditioning where low supply current, useful bandwidth, and compact four-channel integration are more important than very high precision.
Each channel provides independent inverting and non-inverting inputs and an output. The family is designed for low-power, wide-bandwidth single-supply operation, and the TLV2635 version includes shutdown capability. The shutdown function can reduce supply consumption when the amplifier channels are not required, although exact shutdown timing and current should be confirmed in the manufacturer datasheet before final timing calculations.
Typical uses include industrial sensor interfaces, low-frequency instrumentation, audio and communications signal conditioning, portable measurement equipment, and general-purpose analog amplification. Four channels in one 16-pin DIP can reduce board area compared with four separate single amplifiers, provided the through-hole footprint and operating temperature requirements suit the target assembly process.
Designers should verify the supported supply-voltage range, input common-mode limits, output swing, output-current capability, and shutdown logic in the manufacturer datasheet. Decoupling capacitors should be placed close to the power pins, and unused amplifier inputs should be biased so they remain in a valid common-mode region. Prototype on the target board because the DIP package is suited to through-hole assembly rather than high-density surface-mount layouts.
This page combines the manufacturer-family operating characteristics, package details, sourcing guidance, application analysis, and candidate drop-in information. It also distinguishes exact electrical features from specifications that still require validation, helping engineers plan signal-chain design and PCB assembly before placing an order.
के लिए ड्रॉप-इन विकल्प TLV2635IN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
TLV2635IN-T6A
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV2635IN-TV3
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TLV2635IN Maximum Ratings और Electrical Characteristics
| Amplifier Circuit Count | 4 circuits |
| Product Type | Low-power, wide-bandwidth operational amplifier |
| Gain-Bandwidth Product | 9 MHz |
| Supply Current Per Channel | 730 uA/channel |
| Supply Configuration | Single supply |
| Output Swing | Rail-to-rail |
| Common-Mode Input Range | Includes ground |
| Shutdown Support | Yes |
| Package Type | 16-PDIP |
| माउंटिंग प्रकार | Through hole |
| Pin Pitch | 0.300 in (7.62 mm) |
TLV2635IN पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Channel 1 output |
| पिन 2 | -IN1 — Channel 1 inverting input |
| पिन 3 | +IN1 — Channel 1 non-inverting input |
| पिन 4 | V+ — Positive supply connection |
| पिन 5 | +IN2 — Channel 2 non-inverting input |
| पिन 6 | -IN2 — Channel 2 inverting input |
| पिन 7 | OUT2 — Channel 2 output |
| पिन 8 | OUT3 — Channel 3 output |
| पिन 9 | -IN3 — Channel 3 inverting input |
| पिन 10 | +IN3 — Channel 3 non-inverting input |
| पिन 11 | V- — Negative supply connection |
| पिन 12 | +IN4 — Channel 4 non-inverting input |
| पिन 13 | -IN4 — Channel 4 inverting input |
| पिन 14 | OUT4 — Channel 4 output |
| पिन 15 | SHDN — Shutdown control input |
| पिन 16 | NC — Not connected |
सामान्य अनुप्रयोग
TLV2635IN के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Portable Measurement Equipment, Audio Preamplifier Conditioning, Communications Interface Buffering, Test and Measurement Front Ends, Low-Voltage Control Loops.
Industrial Sensor Signal Conditioning
The TLV2635IN is appropriate for buffering and conditioning signals from industrial sensors when four channels and low per-channel supply current simplify the analog front end. Its 9 MHz gain-bandwidth product provides useful closed-loop bandwidth for many sensor signals, while rail-to-rail output increases the available output range in low-voltage systems. The common-mode input range includes ground, which supports sensors centered near 0 V. Use the four amplifier channels for differential inputs, gain stages, or active filtering, and verify the actual sensor output range against the device input limits before production use.
अनुशंसित
Portable Measurement Equipment
The TLV2635IN suits portable or low-power measurement equipment where four analog channels must fit into a compact through-hole board. Approximately 730 uA of supply current per channel helps control consumption, while the 9 MHz gain-bandwidth product is more than adequate for many low-frequency measurement and control paths. The rail-to-rail output can improve utilization of a limited supply range. Shutdown support allows the amplifier to be disabled when measurements are not active, subject to the exact logic and timing requirements in the manufacturer datasheet.
अनुशंसित
Audio Preamplifier Conditioning
The TLV2635IN can provide gain and impedance conditioning in general-purpose audio preamplifier paths that operate from a single supply. Its 9 MHz gain-bandwidth product permits useful bandwidth at moderate closed-loop gains, and the rail-to-rail output helps preserve signal swing near the supply limits. Four channels can process multiple low-level audio lines, although low-noise performance and maximum output-current capability should be checked against the signal source and load. Avoid using the device for high-current headphone drive without confirming its output-stage limits.
अनुशंसित
Communications Interface Buffering
The TLV2635IN is applicable to communications equipment requiring four single-supply buffer or gain stages close to a connector or sensor interface. Rail-to-rail output supports flexible signal swing, and the approximately 730 uA per-channel supply current suits compact interface electronics. The 9 MHz gain-bandwidth product can handle moderate-bandwidth conditioning, but actual channel bandwidth depends on the selected closed-loop gain and load. Confirm input capacitance, output drive, and supply limits in the manufacturer datasheet before using it with high-speed lines.
अनुशंसित
Test and Measurement Front Ends
The TLV2635IN can be used in general-purpose test equipment for four low-level signal buffers, active filters, or channel amplifiers. Its 9 MHz gain-bandwidth product supports wider closed-loop bandwidth than precision-only amplifiers, and the single-supply architecture simplifies system power design. The common-mode range including ground makes it suitable for bipolar sensor signals around ground, while rail-to-rail output provides useful headroom. For metrology applications, verify input offset, drift, and noise limits before choosing it over a precision amplifier.
अनुशंसित
Low-Voltage Control Loops
The TLV2635IN can implement low-voltage control, feedback, and error-amplifier functions in industrial or embedded systems. Its four channels allow several control loops to share one package, and the 9 MHz gain-bandwidth product supports faster loop response than a low-bandwidth general-purpose amplifier. Rail-to-rail output helps drive signals within a narrow supply range, while shutdown may save power during inactive operating states. Validate stability, source impedance, output loading, and supply range against the intended control topology before deployment.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा TLV2635IN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | TLV2635IN-T6A | TLV2635IN-TV3 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-PDIP | 16-PDIP | 16-PDIP |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 9 MHz | 9 MHz | 9 MHz |
| Supply Configuration | Single supply | Single supply | Single supply |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shutdown Support | Yes | Yes | Yes |
| Mounting Type | Through hole | Through hole | Through hole |
मुख्य विशेषताएँ
- Combines four channels with a 9 MHz gain-bandwidth product (बनामTLV2635IN-T6A)
- Provides shutdown support for reducing inactive-state consumption (बनामTLV2635IN-TV3)
- Combines rail-to-rail output with a common-mode range that includes ground (बनामTLV2635IN-T6A)
डिज़ाइन नोट्स
Reserve a 16-pin through-hole footprint with 0.300-inch, 7.62 mm row spacing. Place the positive supply decoupling capacitor close to the V+ pin and connect the ground reference directly to the V- pin. Because this is a multi-amplifier package, route each channel to minimize shared-impedance coupling and keep sensitive inputs away from supply and shutdown traces.
Do not allow either input of an unused channel to float. Tie the non-inverting input to a defined bias point and configure the inverting input for stable operation. Also verify the shutdown-pin logic against the manufacturer datasheet, since leaving the control at an undefined voltage can place the amplifier in an unintended operating state and increase supply consumption.
Treat the 9 MHz gain-bandwidth product as an amplifier-level parameter rather than guaranteed closed-loop bandwidth. Actual bandwidth depends on gain, feedback topology, source impedance, load, and PCB parasitics. Add small feedback resistors where required to control high-frequency peaking, and use short ground returns to reduce susceptibility to common-mode noise on low-level sensor inputs.
अनुपालन जानकारी
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was available for the exact ordering code. Confirm the applicable declarations using the exact manufacturer orderable code and its current documentation.