STMicroelectronics

TS3702CD - Micropower Dual CMOS Comparator | STMicro

MPN: TS3702CD ✓ सक्रिय
9 uA typical Vdss 8-pin SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

TS3702CD अवलोकन

The STMicroelectronics TS3702CD is a dual micropower CMOS voltage comparator with 9 uA typical supply current per comparator, a 2 us typical response time, and push-pull outputs, packaged in an 8-pin SOIC. The device provides two independent comparators with high input impedance, making it suitable for low-power sensing and threshold-detection circuits.

A voltage comparator is an analog integrated circuit that compares an input voltage against a reference voltage and changes its digital output state when the compared signals cross. The TS3702 belongs to the comparator class within analog and mixed-signal semiconductors. Its push-pull CMOS outputs eliminate the external pull-up resistor normally required by open-collector comparators such as the bipolar LM393, reducing component count and simplifying output interfacing.

The TS3702 operates from single or dual supplies and supports input common-mode ranges extending below and above the supply rails. Typical supply current is 9 uA per comparator, approximately twenty times lower than a bipolar LM393 according to the manufacturer datasheet. Input impedance is 10^12 ohms typical, helping minimize loading on high-impedance sensors. Maximum input offset voltage is listed as 6.5 mV, so applications requiring tighter threshold accuracy should include offset and propagation-delay error in the system budget.

Each channel contains an input stage, a logic decision element, and a CMOS push-pull output driver. The push-pull stage sources or sinks output current, allowing direct connection to CMOS logic inputs. Because the output actively drives both states, the device does not need a pull-up resistor, although PCB design should still provide adequate output-current margin and account for the input capacitance of the following stage.

Typical uses include battery-powered threshold detection, window comparators, sensor signal conditioning, overvoltage monitoring, temperature-setpoint control, and portable instrumentation. The dual-channel configuration also allows one package to implement a two-threshold window monitor or compare two independent sensor signals without adding a second comparator package.

For low-noise analog signals, keep comparator input traces short, place the input reference network close to the device, and avoid routing them beside switching-node traces. Add supply-bypass capacitance near the power pins and verify that the output state never conflicts with another push-pull driver. Because the output is actively driven, do not connect two comparator outputs together without an isolation device.

This page combines package and pin information with application guidance, drop-in candidate evaluation, comparison parameters, and practical design notes that help engineers move from datasheet review to a working low-power analog front end.

के लिए ड्रॉप-इन विकल्प TS3702CD — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

TS3702IYDT

✅ ड्रॉप-इन
📦 SOIC-8
Same TS3702 dual micropower family and 8-pin SOIC footprint; temperature-grade ordering code differs from TS3702CD

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TS393IDT

✅ ड्रॉप-इन
📦 SOIC-8
Similar dual micropower comparator with approximately 10 uA supply current per channel versus 9 uA for TS3702CD, a difference of about 11%

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TS3702CDT

✅ ड्रॉप-इन
📦 SOIC-8
Electrically identical TS3702 device in tape-and-reel rather than tube shipment format; key electrical ratings remain unchanged

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLC3702CDR

✅ ड्रॉप-इन
📦 SOIC-8
Dual CMOS push-pull comparator in the same 8-pin class; input offset and timing must be rechecked against the TS3702CD limits of 6.5 mV and 2 us typical

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV3702CD

✅ ड्रॉप-इन
📦 SOIC-8
Nanopower comparator with approximately 560 nA per channel versus 9 uA for TS3702CD; minimum operating supply voltage and timing require circuit-level verification

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TS3702CD Maximum Ratings और Electrical Characteristics

Comparator Type Dual general-purpose voltage comparator
Number of Channels 2 channels
Supply Current per Comparator 9 uA typical
Response Time 2 us typical
Input Impedance 10^12 ohm typical
Maximum Input Offset Voltage 6.5 mV
आउटपुट प्रकार Push-pull CMOS
Supply Voltage Configuration Single or dual supply
Maximum Supply Voltage +/-16 V
Common-Mode Input Range Extends below and above the supply rails
पैकेज 8-pin SOIC
माउंटिंग प्रकार Surface mount
External Pull-Up Resistor Not required for push-pull outputs

TS3702CD पिन कॉन्फ़िगरेशन

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
पिन 1 OUT1 — Comparator 1 push-pull output
पिन 2 IN1- — Comparator 1 inverting input
पिन 3 IN1+ — Comparator 1 non-inverting input
पिन 4 V- — Negative supply or ground connection
पिन 5 IN2+ — Comparator 2 non-inverting input
पिन 6 IN2- — Comparator 2 inverting input
पिन 7 OUT2 — Comparator 2 push-pull output
पिन 8 V+ — Positive supply connection

सामान्य अनुप्रयोग

TS3702CD के लिए उपयुक्त है 6 अनुप्रयोगs: Battery Voltage Threshold Detection, Window Comparator for Limit Monitoring, High-Impedance Sensor Signal Conditioning, Portable Measurement and Test Equipment, Overvoltage and Undervoltage Protection, Automotive and Industrial Low-Power Control.

⚡

Battery Voltage Threshold Detection

The TS3702CD fits battery-powered systems that must detect a low-battery condition without continuously powering a bipolar comparator. Its 9 uA typical current per comparator and 10^12 ohm typical input impedance limit loading on the monitored source. One channel can compare a divided battery voltage with a reference while the other remains available for a second threshold or enable function. Design the divider so its impedance does not degrade the reference accuracy, and account for the maximum input offset voltage of 6.5 mV when setting the trip point.

🏭

Window Comparator for Limit Monitoring

The two independent TS3702CD channels can implement an upper and lower limit monitor around one input voltage. One comparator detects the high threshold while the other detects the low threshold, and the two push-pull outputs can be combined with simple logic to create an in-range signal. The 2 us typical response supports prompt limit detection, while the actively driven outputs avoid the pull-up resistor and rise-time penalty associated with open-collector comparators. Confirm output logic polarity and reference tolerances before combining the channels.

🧩

High-Impedance Sensor Signal Conditioning

The TS3702CD is useful when a sensor produces a slowly changing signal that must be converted into a clean digital decision. Its 10^12 ohm typical input impedance minimizes loading on resistive dividers, capacitive sensors, and leakage-sensitive analog front ends. Use the comparator to detect a sensor threshold after amplification, then rely on its push-pull output to drive a CMOS input directly. For slow signals, add hysteresis to prevent chatter around the switching point and evaluate the 6.5 mV maximum offset against the sensor's smallest meaningful change.

🔧

Portable Measurement and Test Equipment

Portable instruments benefit from the TS3702CD because two comparisons are available in one 8-pin SOIC while each channel draws only 9 uA typical. The device can supervise a control voltage, identify a probe connection state, or generate an over-range event without introducing a large standing load on the battery. Its push-pull outputs reduce the component count on a crowded analog board and provide defined output levels when the instrument's supply is stable. Validate common-mode behavior during power-up because the input range extends beyond the supply rails.

🖥️

Overvoltage and Undervoltage Protection

The TS3702CD can supervise a protected power rail by comparing a scaled voltage against precise references and driving a controller or protection latch. Its 2 us typical response time is well suited to fast fault detection, while its low 9 uA per-channel supply consumption adds little overhead to a continuous protection path. Choose resistor ratios with low temperature drift if the protection point must remain accurate, and use the input offset specification as part of the guaranteed fault-detection band. A complementary channel can monitor the opposite rail.

🚗

Automotive and Industrial Low-Power Control

The TS3702CD is appropriate for low-duty-cycle control and sensing boards where a 9 uA per-comparator load supports energy efficiency and the 8-pin SOIC package is easy to assemble. The dual channel allows local decisions close to a sensor, reducing long analog traces through a noisy harness. Its input impedance of 10^12 ohms typical is useful with high-impedance sensing networks. For automotive deployments, verify the ordered grade's temperature and qualification requirements, and confirm the reference network's tolerance over the full environmental range before releasing the design.

अनुशंसित उत्पादों का सारांश

TS3702IYDT Same-family SOIC-8 alternative उपयोग में: Battery Voltage Threshold Detection, High-Impedance Sensor Signal Conditioning, Automotive and Industrial Low-Power Control TLV3702CD Lower-power threshold-detection alternative उपयोग में: Battery Voltage Threshold Detection, High-Impedance Sensor Signal Conditioning, Automotive and Industrial Low-Power Control TS393IDT STMicroelectronics dual-comparator alternative उपयोग में: Window Comparator for Limit Monitoring, Portable Measurement and Test Equipment, Overvoltage and Undervoltage Protection TLC3702CDR Dual push-pull window-monitor candidate उपयोग में: Window Comparator for Limit Monitoring, Overvoltage and Undervoltage Protection TS3702CDT Identical electrical option in tape-and-reel format उपयोग में: Portable Measurement and Test Equipment
What is the TS3702CD?
The TS3702CD is an STMicroelectronics dual micropower CMOS voltage comparator in an 8-pin SOIC package. It contains two independent general-purpose comparators with push-pull outputs and consumes 9 uA typical per comparator. According to the TS3702 manufacturer datasheet, the device is positioned as a low-power CMOS alternative to the bipolar LM393, while eliminating the external pull-up resistor required by open-collector outputs.
What is the supply current of TS3702CD?
The TS3702CD consumes 9 uA typical per comparator, as stated in the STMicroelectronics TS3702 datasheet. For a dual comparator operating simultaneously, that corresponds to approximately 18 uA typical. The manufacturer describes this as approximately twenty times lower consumption than a bipolar LM393, making the TS3702CD suitable for battery-powered monitoring systems where continuous comparator current materially affects the standby budget.
Where can I download the TS3702CD datasheet PDF?
The official TS3702CD datasheet is available from the STMicroelectronics product website at https://www.st.com/resource/en/datasheet/ts3702.pdf. It contains the device description, electrical characteristics, pin configuration, and application information for the complete TS3702 family. Use the manufacturer datasheet together with the selected SO-8 package drawing when assigning PCB land patterns and signal names.
What is the TS3702CD pinout?
The TS3702CD uses the standard 8-pin dual-comparator arrangement: OUT1 on pin 1, IN1- on pin 2, IN1+ on pin 3, V- on pin 4, IN2+ on pin 5, IN2- on pin 6, OUT2 on pin 7, and V+ on pin 8. Assign the two inputs carefully because reversing the positive and negative inputs reverses the comparison result and can change the behavior of a threshold-detection circuit.
Does the TS3702CD need an output pull-up resistor?
No external pull-up resistor is required because the TS3702CD uses a push-pull CMOS output stage. The output actively sources or sinks current, unlike the open-collector output used by an LM393. This reduces the component count and avoids the slow pull-up RC time constant, although the connected load must remain within the output-current limits published in the manufacturer datasheet.
How fast is the TS3702CD comparator response?
The TS3702CD has a typical response time of 2 us, according to the STMicroelectronics TS3702 datasheet. A separate distributor specification listing also identifies the device as a 1500 ns nominal comparator. When designing a timed control loop, include comparator delay, input overdrive, reference-node settling, and the response time of the following digital stage in the worst-case timing budget.
Can TS3702CD operate from a single supply?
Yes, the TS3702CD supports single-supply and dual-supply operation and can accept input voltages that extend below or above its supply rails. The maximum supply voltage is listed as plus or minus 16 V. In single-supply designs, bias the reference within the usable input range and verify the output-state behavior at the negative supply rail before releasing the circuit into production.
TS3702CD vs TS3702CDT - which part should I order?
TS3702CD and TS3702CDT use the same 8-pin SOIC comparator device, with the order-code suffix identifying the shipment format. TS3702CD is listed in a tube format, while TS3702CDT is the tape-and-reel format used for automated assembly. Both provide the same dual micropower CMOS comparator function, so the correct choice is determined by the assembly process and required packing format rather than by electrical performance.
What is the best drop-in replacement for TS3702CD?
TS3702IYDT is the closest same-family replacement candidate because it retains the dual micropower comparator architecture and 8-pin SOIC footprint. TS393IDT is another STMicroelectronics 8-pin SOIC alternative, while TLC3702CDR and TLV3702CD are cross-brand candidates that require closer review of supply current, offset voltage, timing, and output behavior. Confirm every electrical limit and pin function before substituting a part.
Is TS3702CD suitable for battery-powered monitoring?
The TS3702CD is well suited to battery-powered monitoring because its typical supply current is only 9 uA per comparator. A dual-channel circuit can continuously compare a battery voltage against a reference or detect an upper and lower threshold. Low quiescent current must be balanced against the comparator's 6.5 mV maximum offset voltage when the difference between the monitored voltage and the reference is small.
What can replace TS3702CD in a window comparator circuit?
A drop-in replacement must preserve the 8-pin SOIC footprint, push-pull output arrangement, and the input and output functions used by the window comparator. TS3702IYDT and TS393IDT are the strongest same-manufacturer candidates to evaluate first. TLC3702CDR or TLV3702CD may fit the footprint, but their current consumption and timing characteristics must be checked because lower power or faster operation can change system-level behavior.
When should I choose TS3702CD over TLV3702CD?
Choose TS3702CD when a 9 uA-per-comparator micropower device with the TS3702 family's established 8-pin SOIC pinout is the priority. TLV3702CD targets much lower supply current and a lower minimum operating supply voltage, which can be advantageous in extreme low-power designs. The trade-off is that changing to TLV3702CD requires rechecking threshold accuracy, propagation delay, input common-mode behavior, and system-level power sequencing.
Is TS3702CD pin-compatible with TLC3702CDR?
TLC3702CDR is a candidate for review as an 8-pin dual CMOS push-pull comparator, but it should not be treated as automatically interchangeable. The cross-reference information specifically recommends evaluating input offset behavior and other reliability characteristics. Confirm pin functions, supply limits, common-mode range, output-current capability, and propagation delay in the applicable manufacturer datasheets before approving the substitution.
What are the key specifications of TS3702CD that engineers should know?
The key TS3702CD specifications are a dual comparator configuration, 9 uA typical supply current per channel, 2 us typical response time, 10^12 ohm typical input impedance, and a maximum input offset voltage of 6.5 mV. The device uses actively driven push-pull CMOS outputs and is offered in an 8-pin SOIC package. These values define its suitability for low-power threshold detection, sensing, and window-comparator designs.
How do I connect an unused TS3702CD comparator channel?
Do not leave an unused comparator input floating, because noise on a high-impedance input can cause unpredictable output transitions. Tie the unused non-inverting input to a defined bias point within the common-mode range and connect the unused inverting input to the same point so the output remains in a stable state. Confirm that the selected bias point satisfies both input pins' voltage limits in the manufacturer datasheet.
Where can I buy TS3702CD and what is the current lead time?
Use the Request a Quote form on this page to request current TS3702CD pricing, stock status, minimum order quantity, and production lead time. The 8-pin SOIC package is available from multiple authorized distribution channels, but inventory and lead time change with demand. Provide your target quantity, date code requirement, and assembly packaging preference when requesting the quotation.

के लिए इंजीनियरिंग संदर्भ डेटा TS3702CD — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TS3702CD when a compact, dual-channel micropower comparator is needed for threshold detection, window monitoring, or sensor conditioning, particularly when each channel can operate from approximately 9 uA and the system uses 8-pin SOIC assembly. TS3702IYDT is the preferred same-family candidate when supply continuity across ordering codes matters. TS393IDT is reasonable when an STMicroelectronics alternative with a similar supply-current level is sufficient, but its timing and offset characteristics require review. TLC3702CDR may fit a cross-brand sourcing strategy, although offset and timing must be revalidated. TLV3702CD is appropriate when minimum power consumption outweighs the need to retain the TS3702 family's operating characteristics. For every substitution, verify pin functions, common-mode range, output-current capability, offset voltage, propagation delay, and temperature-grade requirements before approving the change.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TS3702IYDT TS393IDT TS3702CDT TLC3702CDR TLV3702CD
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Comparator Channels 2 2 2 2 2 2

मुख्य विशेषताएँ

  • Two micropower comparators in one compact package (बनामTS3702CDT)
  • Actively driven outputs reduce external components (बनामTLC3702CDR)
  • Established TS3702 family electrical behavior (बनामTLV3702CD)
  • Close same-manufacturer sourcing path (बनामTS3702IYDT)

डिज़ाइन नोट्स

Budget the comparator supply current as approximately 9 uA per active channel, or 18 uA when both TS3702CD channels are operating. Add leakage from the reference divider, protection diodes, and any external logic because these contributions can dominate a micropower design. Place the supply bypass capacitor at the V+ and V- pins, and keep the ground return short so switching current in the external logic does not shift the comparator threshold.

Do not connect two TS3702CD outputs directly together. The push-pull output stage can source or sink current actively, so a conflict between outputs may produce excessive current. Use series isolation resistors or a logic function when combining comparator states. Also avoid floating inputs: bias both inputs of an unused channel to a defined voltage and verify that the resulting output remains stable.

The 10^12 ohm typical input impedance allows the TS3702CD to sense high-impedance nodes, but long PCB traces can still pick up noise and leakage. Keep inverting and non-inverting traces short, enclose the reference divider with a ground guard where practical, and route them away from switching nodes. For slow signals, add positive feedback to create hysteresis greater than the combined offset and noise margin.

Treat the two channels as independent analog paths and route each reference divider directly to its assigned input pin. Maintain a quiet return plane beneath the analog section, bypass the supply at the device, and provide a solid ground connection at pin 4. Confirm the exposed board area and land pattern against the official SO-8 package drawing before releasing the PCB artwork.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The manufacturer datasheet establishes the electrical characteristics, but the listed compliance and automotive-qualification attributes require confirmation against the current STMicroelectronics product documentation or supplier certificates.

डेटा सत्यापन तिथि: 2026-11-16 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

TS3702CD datasheet TS3702CD datasheet pdf TS3702CD pinout STMicroelectronics TS3702CD TS3702CD SOIC-8 comparator TS3702CD supply current TS3702CD input offset voltage TS3702CD response time TS3702CD equivalent TS3702CD replacement TS3702CD vs TLV3702CD TS3702CD price TS3702CD stock TS3702CD battery monitoring circuit TS3702CD window comparator

संबंधित कंपोनेंट्स और शब्द

STMicroelectronics TS3702CD TS3702 TS3702IYDT TS393IDT TLC3702CDR TLV3702CD voltage comparator dual comparator analog integrated circuit mixed-signal semiconductor CMOS push-pull output open-collector output LM393 low-dropout regulator SOIC-8 surface mount SMD 9 uA supply current 2 us response time 10^12 ohm input impedance 6.5 mV input offset battery-powered monitoring window comparator
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें