TS3702CD - Micropower Dual CMOS Comparator | STMicro
N.º da peça: TS3702CD ✓ AtivoTS3702CD Visão geral
A voltage comparator is an analog integrated circuit that compares an input voltage against a reference voltage and changes its digital output state when the compared signals cross. The TS3702 belongs to the comparator class within analog and mixed-signal semiconductors. Its push-pull CMOS outputs eliminate the external pull-up resistor normally required by open-collector comparators such as the bipolar LM393, reducing component count and simplifying output interfacing.
The TS3702 operates from single or dual supplies and supports input common-mode ranges extending below and above the supply rails. Typical supply current is 9 uA per comparator, approximately twenty times lower than a bipolar LM393 according to the manufacturer datasheet. Input impedance is 10^12 ohms typical, helping minimize loading on high-impedance sensors. Maximum input offset voltage is listed as 6.5 mV, so applications requiring tighter threshold accuracy should include offset and propagation-delay error in the system budget.
Each channel contains an input stage, a logic decision element, and a CMOS push-pull output driver. The push-pull stage sources or sinks output current, allowing direct connection to CMOS logic inputs. Because the output actively drives both states, the device does not need a pull-up resistor, although PCB design should still provide adequate output-current margin and account for the input capacitance of the following stage.
Typical uses include battery-powered threshold detection, window comparators, sensor signal conditioning, overvoltage monitoring, temperature-setpoint control, and portable instrumentation. The dual-channel configuration also allows one package to implement a two-threshold window monitor or compare two independent sensor signals without adding a second comparator package.
For low-noise analog signals, keep comparator input traces short, place the input reference network close to the device, and avoid routing them beside switching-node traces. Add supply-bypass capacitance near the power pins and verify that the output state never conflicts with another push-pull driver. Because the output is actively driven, do not connect two comparator outputs together without an isolation device.
This page combines package and pin information with application guidance, drop-in candidate evaluation, comparison parameters, and practical design notes that help engineers move from datasheet review to a working low-power analog front end.
Alternativas drop-in para TS3702CD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
TS3702IYDT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS393IDT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS3702CDT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLC3702CDR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLV3702CD
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS3702CD Classificações máximas e características elétricas
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Supply Current per Comparator | 9 uA typical |
| Response Time | 2 us typical |
| Input Impedance | 10^12 ohm typical |
| Maximum Input Offset Voltage | 6.5 mV |
| Tipo de saída | Push-pull CMOS |
| Supply Voltage Configuration | Single or dual supply |
| Maximum Supply Voltage | +/-16 V |
| Common-Mode Input Range | Extends below and above the supply rails |
| Encapsulamento | 8-pin SOIC |
| Tipo de montagem | Surface mount |
| External Pull-Up Resistor | Not required for push-pull outputs |
Configuração de pinos do TS3702CD
| Pino 1 | OUT1 — Comparator 1 push-pull output |
| Pino 2 | IN1- — Comparator 1 inverting input |
| Pino 3 | IN1+ — Comparator 1 non-inverting input |
| Pino 4 | V- — Negative supply or ground connection |
| Pino 5 | IN2+ — Comparator 2 non-inverting input |
| Pino 6 | IN2- — Comparator 2 inverting input |
| Pino 7 | OUT2 — Comparator 2 push-pull output |
| Pino 8 | V+ — Positive supply connection |
Aplicações típicas
TS3702CD é adequado para 6 aplicaçãos: Battery Voltage Threshold Detection, Window Comparator for Limit Monitoring, High-Impedance Sensor Signal Conditioning, Portable Measurement and Test Equipment, Overvoltage and Undervoltage Protection, Automotive and Industrial Low-Power Control.
Battery Voltage Threshold Detection
The TS3702CD fits battery-powered systems that must detect a low-battery condition without continuously powering a bipolar comparator. Its 9 uA typical current per comparator and 10^12 ohm typical input impedance limit loading on the monitored source. One channel can compare a divided battery voltage with a reference while the other remains available for a second threshold or enable function. Design the divider so its impedance does not degrade the reference accuracy, and account for the maximum input offset voltage of 6.5 mV when setting the trip point.
Recomendado
Window Comparator for Limit Monitoring
The two independent TS3702CD channels can implement an upper and lower limit monitor around one input voltage. One comparator detects the high threshold while the other detects the low threshold, and the two push-pull outputs can be combined with simple logic to create an in-range signal. The 2 us typical response supports prompt limit detection, while the actively driven outputs avoid the pull-up resistor and rise-time penalty associated with open-collector comparators. Confirm output logic polarity and reference tolerances before combining the channels.
Recomendado
High-Impedance Sensor Signal Conditioning
The TS3702CD is useful when a sensor produces a slowly changing signal that must be converted into a clean digital decision. Its 10^12 ohm typical input impedance minimizes loading on resistive dividers, capacitive sensors, and leakage-sensitive analog front ends. Use the comparator to detect a sensor threshold after amplification, then rely on its push-pull output to drive a CMOS input directly. For slow signals, add hysteresis to prevent chatter around the switching point and evaluate the 6.5 mV maximum offset against the sensor's smallest meaningful change.
Recomendado
Portable Measurement and Test Equipment
Portable instruments benefit from the TS3702CD because two comparisons are available in one 8-pin SOIC while each channel draws only 9 uA typical. The device can supervise a control voltage, identify a probe connection state, or generate an over-range event without introducing a large standing load on the battery. Its push-pull outputs reduce the component count on a crowded analog board and provide defined output levels when the instrument's supply is stable. Validate common-mode behavior during power-up because the input range extends beyond the supply rails.
Recomendado
Overvoltage and Undervoltage Protection
The TS3702CD can supervise a protected power rail by comparing a scaled voltage against precise references and driving a controller or protection latch. Its 2 us typical response time is well suited to fast fault detection, while its low 9 uA per-channel supply consumption adds little overhead to a continuous protection path. Choose resistor ratios with low temperature drift if the protection point must remain accurate, and use the input offset specification as part of the guaranteed fault-detection band. A complementary channel can monitor the opposite rail.
Recomendado
Automotive and Industrial Low-Power Control
The TS3702CD is appropriate for low-duty-cycle control and sensing boards where a 9 uA per-comparator load supports energy efficiency and the 8-pin SOIC package is easy to assemble. The dual channel allows local decisions close to a sensor, reducing long analog traces through a noisy harness. Its input impedance of 10^12 ohms typical is useful with high-impedance sensing networks. For automotive deployments, verify the ordered grade's temperature and qualification requirements, and confirm the reference network's tolerance over the full environmental range before releasing the design.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TS3702CD — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TS3702IYDT | TS393IDT | TS3702CDT | TLC3702CDR | TLV3702CD |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Channels | 2 | 2 | 2 | 2 | 2 | 2 |
Principais diferenciais
- Two micropower comparators in one compact package (vs TS3702CDT)
- Actively driven outputs reduce external components (vs TLC3702CDR)
- Established TS3702 family electrical behavior (vs TLV3702CD)
- Close same-manufacturer sourcing path (vs TS3702IYDT)
Notas de projeto
Budget the comparator supply current as approximately 9 uA per active channel, or 18 uA when both TS3702CD channels are operating. Add leakage from the reference divider, protection diodes, and any external logic because these contributions can dominate a micropower design. Place the supply bypass capacitor at the V+ and V- pins, and keep the ground return short so switching current in the external logic does not shift the comparator threshold.
Do not connect two TS3702CD outputs directly together. The push-pull output stage can source or sink current actively, so a conflict between outputs may produce excessive current. Use series isolation resistors or a logic function when combining comparator states. Also avoid floating inputs: bias both inputs of an unused channel to a defined voltage and verify that the resulting output remains stable.
The 10^12 ohm typical input impedance allows the TS3702CD to sense high-impedance nodes, but long PCB traces can still pick up noise and leakage. Keep inverting and non-inverting traces short, enclose the reference divider with a ground guard where practical, and route them away from switching nodes. For slow signals, add positive feedback to create hysteresis greater than the combined offset and noise margin.
Treat the two channels as independent analog paths and route each reference divider directly to its assigned input pin. Maintain a quiet return plane beneath the analog section, bypass the supply at the device, and provide a solid ground connection at pin 4. Confirm the exposed board area and land pattern against the official SO-8 package drawing before releasing the PCB artwork.
Informações de conformidade
The manufacturer datasheet establishes the electrical characteristics, but the listed compliance and automotive-qualification attributes require confirmation against the current STMicroelectronics product documentation or supplier certificates.