XMC4800E196K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
MPN: XMC4800E196K2048AAXQMA1 ✓ सक्रियXMC4800E196K2048AAXQMA1 अवलोकन
An industrial microcontroller is a semiconductor device that executes embedded control firmware, reads sensor and process inputs, and controls actuators or communications hardware. The XMC4000 family combines an Arm Cortex-M4 processor core with embedded peripherals and Ethernet connectivity in a single integrated circuit, reducing the component count needed for industrial network nodes.
Key characteristics include a 144 MHz maximum clock, 2,048 kB of flash, 32-bit processing, and an operating supply identified as 3.3 V. The target ordering code is associated with the PG-LFBGA-196-2 package and tray presentation. Its 196-ball land pattern provides a high pin count suitable for extensive peripheral connections and Ethernet implementation, but it also requires a dense, carefully routed PCB layout.
The architecture follows the Arm Cortex-M4 processor model and targets embedded real-time workloads. At 144 MHz, the core provides substantially more instruction throughput than lower-frequency general-purpose control devices, while the integrated Ethernet interface allows network communication without requiring a separate controller. Exact RAM capacity, peripheral inventory, Ethernet details, voltage tolerances, and temperature limits must be confirmed in the manufacturer documentation before schematic release.
Typical applications include industrial Ethernet controllers, programmable automation equipment, networked sensors, motor and motion-control systems, industrial gateways, and embedded communications equipment. The combination of local real-time processing and Ethernet connectivity is especially useful where control decisions must occur locally while status, configuration, and diagnostic data are exchanged over a network.
PCB implementation should prioritize short return paths for supply and ground, controlled clock routing, and careful assignment of high-speed Ethernet signals. The LFBGA-196 footprint demands adequate escape routing and multilayer-board planning; verify the manufacturer pinout, ball map, exposed-pad requirements, and recommended stack-up before releasing artwork. Provide local decoupling according to the device power architecture and use simulation or measurement to confirm Ethernet signal integrity.
This page combines the exact ordering information, key device characteristics, sourcing workflow, replacement guidance, and application-focused design considerations. It also distinguishes confirmed manufacturer information from parameters that require engineering confirmation, helping teams move efficiently from component selection to a manufacturable industrial-control design.
के लिए ड्रॉप-इन विकल्प XMC4800E196K2048AAXQMA1 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।
विकल्प अनुरोध करेंXMC4800E196K2048AAXQMA1 Maximum Ratings और Electrical Characteristics
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M4 |
| Architecture | ARM 32-bit |
| अधिकतम क्लॉक फ़्रीक्वेंसी | 144 MHz |
| Flash Memory | 2 MB (2M x 8 bit) |
| ऑपरेटिंग सप्लाई वोल्टेज | 3.3 V |
| Ethernet Support | Integrated Ethernet |
| Core Count | 1 core |
| Application Class | Industrial |
| पैकेज | PG-LFBGA-196-2, 196 pins |
| Package Family | LFBGA |
| माउंटिंग प्रकार | Surface mount |
| Packaging | Tray |
XMC4800E196K2048AAXQMA1 lfbga पिन कॉन्फ़िगरेशन गाइड
XMC4800E196K2048AAXQMA1 (lfbga पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: XMC4800E196K2048AAXQMA1.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
XMC4800E196K2048AAXQMA1 के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Ethernet Automation Controller, Networked Sensor Gateway, Programmable Automation Controller, Motor and Motion Control System, Industrial Communication Gateway, Connected Test and Measurement Equipment.
Industrial Ethernet Automation Controller
The XMC4800E196K2048AAXQMA1 fits an industrial Ethernet automation node because it combines a 144 MHz Arm Cortex-M4 core, 2 MB of flash, and integrated Ethernet in one device. The processor can execute real-time control and diagnostics while the network interface carries configuration, status, and process data. Its 196-pin LFBGA package also provides more signal connections than a compact MCU, supporting sensors, local I/O, and communications circuitry. Design the PCB with short Ethernet routes, continuous ground references, and closely placed decoupling. Confirm the exact MAC, PHY, and external-interface requirements in the manufacturer documentation before finalizing the schematic.
अनुशंसित
Networked Sensor Gateway
The XMC4800E196K2048AAXQMA1 is appropriate for a gateway that must acquire local sensor information and forward it over Ethernet. At up to 144 MHz, the Cortex-M4 core can service multiple communication tasks, apply filtering, and maintain deterministic timing for critical measurements. The 2 MB of flash provides room for firmware, protocol handlers, and configuration logic. Use the broad 196-pin package to connect digital sensors, local status inputs, and external transceivers, but preserve uninterrupted ground and power planes for reliable Ethernet performance. Firmware partitioning should isolate real-time acquisition from network traffic to avoid unpredictable control latency.
अनुशंसित
Programmable Automation Controller
The XMC4800E196K2048AAXQMA1 supports programmable automation equipment that combines deterministic machine control with supervisory networking. Its 144 MHz Arm Cortex-M4 core provides substantial processing capacity for sequencing, state machines, and diagnostics, while 2 MB of flash supports a larger embedded application than a basic control MCU. The 196-pin LFBGA-196-2 package accommodates field-bus, digital I/O, analog interfaces, and communications connections without relying on a separate host processor. Keep high-current actuator drive paths away from sensitive logic, use separate decoupling branches, and validate timing margins across the full operating-temperature range before production release.
अनुशंसित
Motor and Motion Control System
The XMC4800E196K2048AAXQMA1 can serve as the central controller in a connected motor-control system because its 144 MHz Cortex-M4 core is suited to frequent control-loop computation. The available package connectivity supports encoders, current and position sensing, digital commands, and network supervision. Integrated Ethernet allows drive parameters, fault information, and operating data to be exchanged with a controller or service interface. The design must verify timer channels, encoder interfaces, analog front ends, and electrical limits against the exact device documentation. Keep switching-node and motor-drive circuitry physically separated to reduce noise coupling into the MCU and Ethernet sections.
अनुशंसित
Industrial Communication Gateway
The XMC4800E196K2048AAXQMA1 is well suited to an industrial gateway that translates between embedded control functions and Ethernet-based supervisory systems. Its 2 MB flash capacity accommodates protocol stacks, routing logic, logging, and remote configuration, while the 144 MHz core supports concurrent communication workloads. The 196-pin package provides enough connection density for multiple serial, digital, and network-facing interfaces. In the PCB, route Ethernet differential pairs as controlled impedance traces, maintain uninterrupted reference planes, and place termination and magnetic-interface components according to the selected network design. Firmware should include watchdog recovery, communication retry handling, and safe restart behavior.
अनुशंसित
Connected Test and Measurement Equipment
The XMC4800E196K2048AAXQMA1 can coordinate a networked industrial test or measurement instrument because it combines a 144 MHz control processor, 2 MB of program storage, and Ethernet connectivity. Local sequencing, instrument control, and result processing can run on the Cortex-M4 core while the network interface supports remote configuration and data transfer. Its high-pin-count LFBGA package provides flexible access to sensors, memory, and peripheral interfaces. Preserve analog-signal separation, use independent filtering for sensitive rails, and validate Ethernet timing under the intended operating system and traffic load. The advantage over a small MCU is integration, while the cost is higher PCB and assembly complexity.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा XMC4800E196K2048AAXQMA1 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद |
|---|---|
| Package | PG-LFBGA-196-2 |
| Brand | Infineon Technologies |
| Processor Core | Arm Cortex-M4 |
| Maximum Clock Frequency | 144 MHz |
| Flash Memory | 2 MB |
| Operating Supply Voltage | 3.3 V |
| Ethernet Support | Integrated Ethernet |
| Core Count | 1 core |
| Application Class | Industrial |
| Programming and Delivery | Tray |
मुख्य विशेषताएँ
- Integrated real-time control and network connectivity (बनामXMC4800-E196K2048-AA)
- High-frequency Cortex-M4 processing (बनामXMC4800-E196K2048-AA)
- Substantial embedded program memory (बनामXMC4800-E196K2048-AA)
डिज़ाइन नोट्स
Plan the XMC4800E196K2048AAXQMA1 layout as a high-density mixed-signal design rather than as a generic 196-ball digital package. Use the manufacturer ball map and land pattern to escape power, ground, clock, and communications nets through the shortest practical routes. A multilayer stack-up generally provides the best routing options, but the final layer count, via geometry, and assembly process must be validated against the package drawing and fabrication capabilities. Preserve symmetry and adequate clearances around fine-pitch signal escapes.
Separate the MCU's supply paths from noisy external loads and place local high-frequency decoupling directly at the appropriate power balls. The device operates from a 3.3 V supply according to the product description, but the complete power architecture and tolerance must be taken from the manufacturer documentation. Confirm startup, current transients, internal regulator relationships, and sequencing before assigning rail names in the schematic. Use adequate copper area and via distribution where the package provides multiple supply and ground connections.
Treat Ethernet and clock signals as controlled-impedance nets when the board implementation includes them. Route differential Ethernet pairs together over a continuous reference plane, minimize vias and stubs, and place any required termination according to the complete interface design. Keep switching regulators, high-current actuator outputs, and magnetic-interface components away from sensitive clock and data paths. Validate the final layer stack and termination network with signal-integrity analysis if cable length, edge rate, or industrial noise conditions are demanding.
Do not substitute the base XMC4800-E196K2048-AA designation or another XMC4800 suffix without checking every orderable attribute. Flash density, package code, temperature range, quality level, and delivery form can differ even when the core and Ethernet descriptions look identical. Also avoid treating the 196-pin package as a simple upgrade path from a smaller MCU: ball assignment, exposed-pad requirements, clock support, and peripheral functions may prevent a board-level drop-in replacement.
अनुपालन जानकारी
The exact material-compliance and automotive qualification statements for this ordering code are not stated in the manufacturer and distributor product descriptions. Confirm the applicable Infineon declarations before production release.