Produk (44.000+)

MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL16Z64VFM4

MKL16Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

NXP Semiconductors MKL16Z64VFM4 is a 32-bit ARM Cortex-M0+ Kinetis KL1 microcontroller operating up to 48 MHz, with 64 KB of programmable flash memory and USB and analog peripherals in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device targets low-power embedded systems where compact size, USB connectivity, and a general-purpose ARM microcontroller architecture are important. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one device. The Cortex-M0+ core belongs to the ARM microcontroller product hierarchy, where its compact instruction set and deterministic operation support cost-sensitive embedded control. Within NXP's product portfolio, the Kinetis KL1 family combines this efficient core with low-power design options and USB connectivity for connected peripherals, industrial controls, and compact consumer equipment. The MKL16Z64VFM4 provides 64 KB of flash, a 48 MHz maximum operating frequency, and a 32-bit architecture. Its integrated USB capability allows a design to communicate with a host without adding a separate USB interface controller. Analog peripherals support applications that must measure or control real-world signals, while the 5 mm by 5 mm HVQFN package reduces board area compared with larger leaded microcontrollers. Supported operating-voltage options listed for the device include 1.8 V, 2.5 V, and 3.3 V. The Kinetis architecture is suited to low-power embedded designs because the processor and peripherals are optimized for efficient control workloads. Flash memory retains programmed firmware when power is removed, and the Cortex-M0+ platform provides a familiar instruction set and development ecosystem. Because the MKL16Z64VFM4 has limited 64 KB flash capacity, firmware planning should account for code size, boot code, application logic, and configuration data before finalizing the product's feature set. Typical uses include USB-connected data loggers, compact industrial sensing modules, motor and valve controllers, access-control peripherals, and low-power instrumentation. A USB data logger can use the integrated interface for enumeration and data transfer, while an industrial controller can apply analog peripherals to sensor acquisition and digital outputs to actuators. The small package is especially useful when the PCB area is constrained but full-size leaded packages are undesirable. When laying out the PCB, place input, output, and decoupling capacitors close to their associated power pins, and route the exposed pad to the thermal and ground structure required by the manufacturer package drawing. Preserve USB-signal routing geometry and provide a clean, continuous ground path beneath the interface. Firmware and peripheral assignments should be checked against the manufacturer's reference manual and device configuration guidance before production. This product record combines the exact device identity, core, memory, frequency, package, connectivity, and sourcing information with same-family alternatives and practical integration guidance. It helps engineers assess whether the 32-pin Kinetis KL1 MCU matches a board footprint, power architecture, USB requirement, and embedded firmware budget before committing to a design.

Permintaan RFG Kontak
MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL16Z64VFT4R

MKL16Z64VFT4R - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP MKL16Z64VFT4R is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL1x family, running up to 48 MHz with 64 KB of on-chip Flash and 8 KB of SRAM, supplied in a 48-pin QFN (7x7 mm) package with an exposed thermal pad. The Kinetis KL16 sub-family targets general-purpose low-power applications that need USB connectivity, segment-LCD support, and a richer analog peripheral set than the entry-level KL0x family, while preserving the KL0x energy-efficiency envelope. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a fixed set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M0+ core used here is the most energy-efficient member of the Cortex-M family, designed for deterministic real-time control in cost-constrained embedded products. The Kinetis family sits within NXP's broader portfolio of 32-bit microcontrollers, which in turn belongs to the larger category of microcontrollers and microprocessors (semiconductor -> IC -> MCU -> Kinetis -> KL1x). Key specifications include a 48 MHz maximum core clock, 64 KB program Flash, 8 KB SRAM, USB 2.0 full-speed device with on-chip transceiver, segment-LCD driver (up to 8x36 or 4x40 segments), 12-bit SAR ADC with up to 16 single-ended channels, low-power UART/SPI/I2C peripherals, and an operating voltage range of 1.71 V to 3.6 V. The device also integrates a low-power RTC, multiple low-power modes (VLLS0..3, LLS, VLPR, STOP), DMA, and a low-power timer for periodic wake-up. The 48-QFN exposed-pad package provides a low thermal resistance and a compact 7x7 mm footprint for space-constrained boards. Architecturally, the KL16 combines a Cortex-M0+ core, single-cycle I/O bus, and a peripheral bridge feeding independent timer, communication, and analog subsystems. The on-chip voltage regulator supports internal core supply from a single external 1.71-3.6 V rail, eliminating the need for multiple external supplies. Hardware AES is not present on this sub-family, but the segment LCD controller, USB FS device, and 12-bit ADC give it strong suitability for human-interface, metering, and consumer products. Typical applications include battery-powered sensor nodes, USB-CDC or USB-HID consumer accessories, small appliances with segment-LCD displays, electronic shelf labels, low-end smart meters, and portable medical accessories. The integrated USB transceiver is a notable differentiator for cable-connected low-power peripherals. The combination of segment-LCD, USB, and Cortex-M0+ energy efficiency is uncommon at this price/performance tier. When designing with this part, allocate the exposed pad (EP) on the PCB as a solid copper pour connected to ground to meet thermal and electrical performance; route USB DP/DM as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the XTAL pins. Decouple VDD/VREFL/VREFH with 100 nF ceramics placed as close as possible to the respective pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL17Z128VMP4

MKL17Z128VMP4 - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL17Z128VMP4 is a Kinetis KL17 ultra-low-power 32-bit microcontroller based on the ARM Cortex-M0+ core, operating at up to 48 MHz with 128 KB of flash and 32 KB of SRAM, housed in a 64-pin MAPBGA (5x5 mm) package. It targets battery-powered and energy-harvesting applications where active-mode performance and deep-sleep current must coexist in a small footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a set of on-chip peripherals such as timers, ADCs, and communication controllers. Cortex-M0+ parts occupy the ultra-low-power end of the ARM-M hierarchy and are typically used as microcontrollers -> embedded controllers -> semiconductor devices. The Kinetis KL1x family specifically adds segment-LCD controllers, USB-FS device, and richer analog compared to the entry-level KL0x line. Key features of the MKL17Z128VMP4 include a 16-bit SAR ADC with DMA support, 12-bit DAC, low-power timer, multiple low-power modes (VLLS0/1/3, LLPS, Stop, Wait, Run), flexible USB device (USB-FS) on selected variants, segment LCD controller up to 47 segments, and a 54 GPIO count. The 128 KB flash with 32 KB SRAM ratio makes it suitable for protocol stacks such as BLE HCI or Thread host layers while keeping peripheral support intact. Architecturally, the KL17 uses the Cortex-M0+ with a single-cycle multiplier and a 2-stage pipeline, achieving 0.93 DMIPS/MHz. The wide voltage range of 1.71 V to 3.6 V allows direct connection to single-cell Li-ion, coin cells, or regulated 3.3 V rails, while integrated DC-DC buck converter support simplifies multi-rail designs and improves efficiency in sleep modes where quiescent current drops below 1 uA. Typical applications include wearable fitness bands with segment-LCD displays, battery-powered wireless sensor nodes, USB-CDC/HID peripherals, industrial HMI panels with segment displays, and low-end home appliances. The combination of USB-FS, segment LCD, and low leakage makes the KL17 a strong fit for any 3.3 V coin-cell product that needs a bright display and a wired diagnostic port. When designing with this MCU, place the 0.1 uF decoupling capacitors as close as possible to each VDD/VSS pair and route the VBAT domain separately if a backup RTC battery is used. The segment-LCD bias network requires external charge-pump capacitors; insufficient capacitance leads to display ghosting at extreme temperatures below -20 C. This page synthesizes distributor pricing, drop-in Kinetis same-family alternatives, and practical design notes not consolidated on any single manufacturer page.

Permintaan RFG Kontak
MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP
MKL17Z64VDA4

MKL17Z64VDA4 - 48MHz Cortex-M0+ MCU, 64KB Flash | NXP

The NXP MKL17Z64VDA4 is a 32-bit ultra-low-power microcontroller based on the ARM Cortex-M0+ core running at 48 MHz, with 64 KB flash memory and 16 KB SRAM, housed in a 36-ball XFBGA (MAPBGA-36) package measuring just 3.5 x 3.5 mm. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest level of the embedded computing hierarchy (MCU -> embedded processor -> microprocessor -> SoC). The Kinetis KL family from NXP sits in the ultra-low-power tier of this hierarchy, targeting battery-operated and space-constrained designs where every microamp of current matters. Key features of the MKL17Z64VDA4 include the energy-efficient Cortex-M0+ core, 64 KB (64K x 8) of on-chip flash program memory for firmware storage, 16 KB of SRAM for data and stack, and USB connectivity as noted on the NXP product page. The extremely small 36-XFBGA package with 0.5 mm ball pitch enables placement on the underside of dense PCBs, freeing board area for sensors, radios, or displays in wearables and IoT end nodes. Technically, the device belongs to the Kinetis KL1x general-purpose ultra-low-power family, which provides additional memory, communications, and analog peripheral options beyond the entry-level KL0x family. The 48 MHz Cortex-M0+ executes Thumb instruction set code with a two-stage pipeline, delivering efficient real-time control with a compact gate count and correspondingly low dynamic and static power consumption. Typical applications include battery-powered wearable devices, smart sensors and IoT end nodes, portable medical accessories, and compact human-interface controllers where small footprint and low standby power dominate the selection criteria. When designing with a 3.5 x 3.5 mm BGA, plan the PCB with via-in-pad or escape routing to all 36 balls, and budget rework capability carefully since BGA inspection requires X-ray equipment. This page synthesizes distributor availability data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with all pricing referenced as of 2026-10-18.

Permintaan RFG Kontak
MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL17Z64VFM4

MKL17Z64VFM4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL17Z64VFM4 is an ultra-low-power 32-bit microcontroller with a 48 MHz ARM Cortex-M0+ core, 64 KB of flash memory, USB 2.0 connectivity, and a 32-pin QFN 5 x 5 mm package. It is designed for compact embedded products that require efficient processing, low-power operation, and USB connectivity in a surface-mount footprint. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Kinetis KL1 series combines an ARM Cortex-M0+ core with embedded flash and a selection of serial, analog, timing, and communication peripherals. The MKL17Z64VFM4 belongs to the low-power Kinetis family intended for battery-operated and portable embedded applications. Its principal characteristics include a 32-bit ARM Cortex-M0+ processor operating at 48 MHz, 64 KB of flash, and USB 2.0 support. The 64 KB program-memory capacity is suitable for compact firmware, protocol stacks, control logic, and human-interface applications. The 32-QFN package also reduces board area compared with leaded packages while supporting high-density automated assembly. The 48 MHz Cortex-M0+ architecture provides a practical balance between processing throughput, deterministic control, and low power consumption. Because the processor is designed for embedded workloads, the device can execute control tasks, manage peripherals, and service USB communications without requiring an external microprocessor. Exact SRAM capacity, operating-voltage limits, peripheral configuration, and current-consumption figures should be confirmed in the manufacturer datasheet before a power-sensitive design is released. Typical applications include low-power USB accessories, portable instrumentation, compact control systems, battery-operated equipment, and embedded human-interface devices. In each case, the 64 KB flash allocation supports a meaningful firmware image while the QFN package simplifies integration into compact assemblies. USB 2.0 is particularly useful for configuration, data logging, firmware updates, and connection to a host controller. PCB implementation should follow the manufacturer's land pattern, exposed-pad soldering guidance, and decoupling recommendations exactly. Confirm the board footprint against the 32-pin QFN 5 x 5 mm drawing before layout release, and validate thermal performance at the highest intended operating temperature. Firmware development should use the appropriate Kinetis SDK, configuration tools, and a debug interface compatible with the selected device variant. This product record combines the verified identity, core architecture, memory capacity, frequency, USB capability, package, and lifecycle information with application guidance, replacement considerations, and design-oriented comparison data. It is intended to help engineers identify whether the MKL17Z64VFM4 matches the memory, connectivity, footprint, and low-power requirements of a new embedded design.

Permintaan RFG Kontak
MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VFT4

MKL24Z64VFT4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP Semiconductors MKL24Z64VFT4 is a 48 MHz Arm Cortex-M0+ microcontroller with 64 KB of embedded flash memory, 8 KB of SRAM, and a full-speed USB 2.0 controller in a 48-QFN 7 x 7 mm package. It combines general-purpose embedded processing with USB connectivity and an ultra-low-power design intended for compact, low-energy embedded products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL24Z64VFT4 belongs to the Kinetis KL2x family, combining an Arm Cortex-M0+ core with USB 2.0 connectivity. This places it within the hierarchy of embedded processor, microcontroller, Kinetis L-series MCU, and low-power semiconductor, making it suitable for systems that require compact control and USB communication without a separate USB interface device. The device operates at up to 48 MHz and includes 64 KB of flash for firmware and 8 KB of SRAM for working memory. Its full-speed USB 2.0 capability supports USB device or OTG-oriented designs, while the Kinetis L-series integration includes analog and timing peripherals for embedded measurement and control. The 48-QFN package also exposes a compact land pattern for space-constrained PCB layouts. The Arm Cortex-M0+ architecture provides a straightforward low-complexity software platform for control loops, human-interface devices, portable instruments, and connected accessories. NXP describes the Kinetis KL2x family as pin, software, and tool compatible with other Kinetis L-series MCU families, supporting migration between related Kinetis designs. Firmware development therefore benefits from the broader Kinetis software ecosystem and reusable peripheral-driver patterns. Typical uses include low-power USB data loggers, compact sensor interfaces, USB-connected test equipment, and portable measurement instruments. A designer can place the MCU beside a sensor or transducer, run control and sampling routines from flash and SRAM, and use the integrated USB controller for configuration, data transfer, or firmware updates. The exact USB operating mode and peripheral allocation must be confirmed against the selected device configuration in the manufacturer datasheet. PCB implementation requires careful treatment of the exposed pad, power rails, decoupling, and USB signal routing. Keep the USB D+ and D- traces short and impedance-controlled, provide the decoupling network specified by the datasheet, and use a thermal-via pattern beneath the exposed pad when required by the PCB stack-up. Confirm all VDD, VDDUSB, VDDIO, ground, reset, and programming pins against the package drawing before fabrication. This page combines the exact MKL24Z64VFT4 identity and package information with lifecycle, pricing, sourcing, and interface details. It also organizes verified same-brand alternatives and practical implementation guidance for engineers comparing the KL2x family with adjacent Kinetis L-series devices.

Permintaan RFG Kontak
MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP
MKL24Z64VLH4

MKL24Z64VLH4 - 48MHz Cortex-M0+ 64KB Flash USB 2.0 MCU | NXP

The NXP Semiconductors MKL24Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built on the Arm Cortex-M0+ core, operating up to 48 MHz with 64 KB of embedded Flash memory (64K x 8 organization), 8 KB of SRAM, and a crystal-less full-speed USB 2.0 device controller, all housed in a 64-LQFP (10 x 10 mm) package. The device runs from a single 1.71 V to 3.6 V supply, so it fits industrial 3.3 V rails, 2.5 V legacy systems, and coin-cell powered portable products from the same design. A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, program memory, working RAM, and peripherals such as GPIO, timers, and communication controllers on one die. The Kinetis KL2x family hierarchy runs from MCU to 32-bit microcontroller to ultra-low-power Cortex-M0+ device, and the KL2x branch of that family adds a full-speed USB 2.0 On-The-Go (OTG) controller or a crystal-less full-speed USB device controller on top of the Kinetis KL1x feature set, while remaining software compatible with the KL1x, KL3x, and KL4x families and with Kinetis K20 (Cortex-M4) designs for migration. Key features of this part include 48 MHz Cortex-M0+ execution with a fast interrupt controller, 64 KB of on-chip Flash for firmware, 8 KB of SRAM for buffers and stacks, a 12-bit analog-to-digital converter with 1.71 V to 3.6 V operating span, and on-chip full-speed USB device connectivity that eliminates the need for an external crystal in USB applications. Because the USB controller is crystal-less, the device can enumerate and operate as a USB device directly from an internal trimmed oscillator, reducing bill of materials cost and board area. Technically, the KL2x architecture balances low active current with fast wake-up behavior, allowing the design to sleep between bursts of USB traffic while the transceiver stays responsive to bus events. The 64-LQFP 10 x 10 mm outline is a deliberately conservative industrial package with long leads, which improves soldering yield and rework convenience compared with fine-pitch packages in volume manufacturing, and the exposed thermal spreader path through the leads keeps junction temperature manageable at 48 MHz. Typical applications include USB-to-serial and USB-to-Ethernet adapters, low-cost data loggers, HID and dongle peripherals, industrial sensor hubs and battery-powered portable instruments. The 12-bit ADC and multiple timers make it suitable for battery monitor and environmental sensing nodes, while the USB device controller makes it a natural fit for configuration ports on instrumentation. When designing around this MCU, budget decoupling close to the VDD pins and route the USB D+ and D- differential pair as a short, tightly coupled 90 ohm differential pair on a continuous ground plane. Confirm that your USB host enumerates the crystal-less device at the speed and class you intend, and use the Kinetis KL2x reference designs and SDK examples as the baseline for pin multiplexing and low-power mode entry. This page consolidates the manufacturer product information with a drop-in alternative matrix, a parameter-by-parameter comparison against other Kinetis KL variants, and practical layout and design notes that go beyond the core datasheet feature list.

Permintaan RFG Kontak
MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP
MKL24Z64VLK4

MKL24Z64VLK4 - 48MHz Cortex-M0+ 64KB MCU | NXP

The NXP MKL24Z64VLK4 is a 32-bit Arm Cortex-M0+ Kinetis KL2 microcontroller operating up to 48 MHz, with 64 KB of embedded Flash memory, 8 KB of SRAM, and full-speed USB 2.0 connectivity. The device is offered in an 80-pin FQFP/LQFP package measuring 12 mm by 12 mm and is intended for compact, low-power embedded systems. Its operating supply range extends from 1.71 V to 3.6 V, with an industrial temperature range of -40 °C to +105 °C. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The MKL24Z64VLK4 belongs to the Kinetis KL2x family, which combines an Arm Cortex-M0+ processor with ultra-low-power design features and USB support. Its position within the broader hierarchy is Arm Cortex-M0+ embedded processor, 32-bit microcontroller, Kinetis MCU, and semiconductor. The KL2x family is positioned for low-power embedded applications requiring more connectivity than the earlier KL1x family. Key device characteristics include 64 KB of Flash for firmware, 8 KB of SRAM for working data, operation up to 48 MHz, a 12-bit analog-to-digital converter, and full-speed USB. The 80-pin package provides access to the family’s analog, timing, communication, and general-purpose I/O resources. The 1.71 V to 3.6 V operating range supports low-voltage portable, industrial, and connected embedded equipment, while the -40 °C to +105 °C rating supports temperature-controlled industrial environments. The Arm Cortex-M0+ core supports a compact instruction set and an event-driven architecture suited to control tasks, sensor monitoring, human-interface functions, and low-power background processing. Full-speed USB adds a practical path for connected peripherals, configuration tools, data logging, and firmware update workflows. Because the device combines USB and low-power operation, it can bridge host-device communication duties with embedded control rather than requiring a separate USB interface controller. Typical applications include USB-connected sensor nodes, industrial condition-monitoring equipment, compact data loggers, USB human-interface devices, industrial control panels, and low-energy embedded systems. The 64 KB Flash capacity is appropriate for moderate firmware loads, and the 8 KB SRAM is sufficient for typical control loops and small data buffers. Designs requiring substantially larger application code, extensive graphics storage, or complex protocol stacks should assess whether another MCU in the Kinetis portfolio offers more memory. When laying out the PCB, preserve the pin assignments and exposed-connection requirements defined by the manufacturer datasheet, especially for USB D+ and D− routing. Place USB differential traces as a controlled-impedance pair with minimal stubs and provide suitable decoupling near the power pins. Firmware development should use an NXP-supported toolchain and verify clock, reset, boot, and low-power configurations against the device reference manual before production. This product page consolidates the confirmed MCU specifications, package and supply information, lifecycle status, family context, sourcing options, and design-oriented selection guidance. It also distinguishes the 80-pin target from the 64-pin MKL24Z64VFM4 package variant so engineers can avoid an invalid footprint substitution.

Permintaan RFG Kontak
MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP
MKL25Z128VLK4

MKL25Z128VLK4 - 48MHz Cortex-M0+ 128KB MCU | NXP

The NXP Semiconductors MKL25Z128VLK4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating at 48 MHz, with 128 KB of flash memory and an 80-pin LQFP package measuring 12 x 12 mm. It is suited to embedded control, USB-connected sensing, portable instrumentation, and low-power edge systems. According to the distributor records, the device also provides 16 KB SRAM and full-speed USB. A microcontroller is a compact computer integrated with nonvolatile program memory, working RAM, digital peripherals, and I/O interfaces. It executes firmware, samples sensors, controls actuators, and manages communications without requiring a separate processor. The MKL25Z128VLK4 belongs to the hierarchy Kinetis KL25 microcontroller -> Arm Cortex-M0+ MCU -> 32-bit microcontroller -> embedded processor -> semiconductor. Its principal features include 128 KB of flash for firmware storage, 16 KB of SRAM for runtime data, a 48 MHz Cortex-M0+ core, and full-speed USB. The 80-LQFP package provides enough external connections for mixed-signal products, interface-heavy controls, and designs that favor a leaded package for inspection or assembly. The Kinetis KL2x family also supports migration paths across Kinetis KL1x, KL2x, KL3x, and KL4x devices, as stated by NXP. The Cortex-M0+ architecture favors energy-efficient embedded execution while retaining a conventional 32-bit instruction set and integrated interrupt handling. Flash capacity allows substantially larger applications than 64 KB-class devices, while SRAM supports packet buffers, sampled data, display or communication state, and real-time control tasks. USB integration can reduce the external controller count in connected products. Typical uses include USB data loggers, building-control endpoints, compact industrial monitors, sensor-hub boards, access-control terminals, and low-power portable instruments. The 48 MHz processing rate is suitable for concurrent USB traffic, control loops, protocol handling, and supervisory tasks where workload is modest enough not to require a higher-performance Cortex-M core. Designers should preserve the package pin assignments, supported supply ranges, decoupling requirements, and clock configuration when creating a PCB. The 80-LQFP footprint also requires adequate solder-mask clearance and inspection because its closely spaced leads can complicate manual rework. Firmware development should account for memory-map constraints, USB clocking, peripheral pin multiplexing, and low-power state transitions. This product page consolidates verified manufacturer and distributor identity data, sourcing links, application guidance, and compatibility analysis. Because the supplied sources do not expose complete electrical ratings, pricing values, or a verified pin list, missing fields are explicitly marked rather than inferred.

Permintaan RFG Kontak
MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL25Z32VLK4

MKL25Z32VLK4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL25Z32VLK4 is a 32-bit Kinetis KL2 microcontroller with a 48 MHz Arm Cortex-M0+ core, 32 KB of flash memory, 4 KB of SRAM, and full-speed USB support in an 80-pin LQFP package measuring 12 x 12 mm. The device belongs to the Kinetis KL2x ultra-low-power family and supports operation from 1.8 V, 2.5 V, or 3.3 V supply levels. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The Arm Cortex-M0+ core provides a compact, energy-efficient architecture for embedded control, while the Kinetis family extends this core with low-power operating modes, general-purpose I/O, communication peripherals, and USB connectivity. In the system hierarchy, the MKL25Z32VLK4 is a microcontroller, semiconductor, and programmable embedded-control component. Key features include a 48 MHz operating frequency, 32 KB flash organized as 32K x 8, and 4 KB SRAM. The KL2x family adds a full-speed USB 2.0 controller, with the selected device identified as supporting full-speed USB OTG. Its 80-LQFP package provides 80 external terminals, making it suitable for designs that need broader peripheral access than smaller MCU packages can offer while avoiding a ball-grid-array assembly. The MKL25Z32VLK4 is based on the Arm Cortex-M0+ instruction set, which prioritizes compact code size and efficient real-time control rather than high-performance computing. Its 32 KB flash stores the application firmware, while 4 KB SRAM supports stack space, variables, buffers, and USB or serial-data handling. The manufacturer describes the Kinetis KL2x family as ultra-low-power and notes compatibility with other Kinetis KL1x, KL2x, KL3x, and KL4x devices for migration paths, subject to peripheral and pin-level review. Typical applications include USB-connected data acquisition, compact control panels, industrial sensor nodes, wearable accessories, and embedded USB peripherals. The 48 MHz Cortex-M0+ core is useful for responsive control tasks, and the integrated USB controller can simplify connectivity compared with a discrete USB interface. A board-level design still needs suitable voltage regulation, clocking, decoupling, USB routing, and firmware configuration. Designers should match the exact 80-pin LQFP footprint and verify peripheral assignments, USB implementation details, and board-level connectivity against the NXP documentation before layout. Stable supply voltage and correctly sized local decoupling are fundamental because processor and USB activity can produce fast transient current. USB signal routing also requires controlled impedance and careful placement of the protection and termination network. This product page combines the exact NXP and distributor identification, distinguishes verified electrical facts from unspecified details, identifies same-family migration candidates, and highlights PCB, power, and USB design considerations that help engineers evaluate the MKL25Z32VLK4 beyond a basic catalog description.

Permintaan RFG Kontak
MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP
MKL25Z64VFM4

MKL25Z64VFM4 - 48MHz Cortex-M0+ 64KB Flash MCU | NXP

The NXP Semiconductors MKL25Z64VFM4 is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 48 MHz, with 64 KB of flash memory, 8 KB of SRAM, and full-speed USB support in a 32-pin HVQFN package measuring 5 mm by 5 mm. The device combines a low-power MCU architecture with analog and digital peripherals for compact embedded systems. A microcontroller is an integrated circuit that executes embedded software, reads sensor inputs, controls actuators, and manages communication interfaces. The MKL25Z64VFM4 belongs to the Kinetis KL2 ultra-low-power MCU family, placing it within the hierarchy of embedded microcontroller, ARM Cortex processor, and low-power embedded-system device. Principal features include a 48 MHz ARM Cortex-M0+ core, 64 KB of flash organized as 64K by 8 bits, and 8 KB of SRAM. The part also includes a full-speed USB controller, analog and digital peripherals, and support for 1.8 V, 2.5 V, and 3.3 V operation. Its 32-pin HVQFN package supports dense PCB layouts without relying on a large leaded package. The Kinetis KL2 architecture is designed for embedded applications where processing capability, USB connectivity, and low-power operation must coexist in a compact footprint. The 64 KB flash capacity provides room for bootloader code, application firmware, configuration data, and USB device functions, while the 8 KB SRAM allows real-time tasks and peripheral buffering without external memory. Typical uses include USB-connected sensors, compact data loggers, industrial interface modules, portable measurement equipment, and low-power embedded controllers. The full-speed USB interface can simplify connection to a host system, while the Cortex-M0+ core provides a common architecture for firmware development and peripheral control. PCB design should account for the exposed pad beneath the HVQFN package, provide adequate thermal and electrical grounding, and place decoupling capacitors close to the supply pins. USB routing requires careful control of trace geometry and return paths, and firmware should use the manufacturer's clock, power-management, and USB initialization procedures. This product page combines the core Kinetis KL25 specifications, package information, design guidance, and qualified drop-in alternatives to support component selection, firmware planning, PCB layout, and replacement decisions without requiring engineers to reconstruct the design context from separate documents.

Permintaan RFG Kontak
MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors
MKL25Z64VLH4

MKL25Z64VLH4 - 48MHz Cortex-M0+ USB MCU | NXP Semiconductors

NXP Semiconductors MKL25Z64VLH4 is an ultra-low-power 32-bit Kinetis KL2 microcontroller built around an Arm Cortex-M0+ processor operating up to 48 MHz. It provides 64 KB of Flash memory, 8 KB of SRAM, integrated full-speed USB connectivity, and a 64-LQFP 10 mm × 10 mm package for compact embedded systems. A microcontroller is a semiconductor device that integrates a processor core, programmable memory, peripheral interfaces, and power-management functions on one package. The Cortex-M0+ core combines a compact instruction set with efficient exception handling for embedded control. Within the product hierarchy, the MKL25Z64VLH4 belongs to the Kinetis L series of ultra-low-power microcontrollers, combining general-purpose control, serial connectivity, and USB device or OTG-oriented functions. The 48 MHz maximum operating frequency supports responsive control loops and efficient handling of embedded workloads, while 64 KB of Flash preserves room for firmware, configuration data, and application code. The 8 KB SRAM supports working memory, stack allocation, buffering, and communication tasks without requiring an external memory interface in typical designs. Full-speed USB integration enables direct peripheral connectivity for data acquisition, configuration, logging, and human-interface applications. The device supports 1.8 V, 2.5 V, and 3.3 V operating configurations according to the product listing information. This voltage flexibility makes it suitable for mixed-voltage embedded systems, although power-supply sequencing, decoupling, and signal-level limits must be checked against the manufacturer datasheet before implementation. Its ultra-low-power positioning is useful for systems that spend substantial time idle, sleep, or operating at reduced clock rates. Typical applications include USB-connected data loggers, industrial interface modules, compact control boards, portable measurement equipment, and low-power embedded products. The 64-LQFP package exposes more general-purpose I/O than smaller microcontroller packages and remains practical for automated assembly, inspection, and prototype rework. Software development is supported through the wider Kinetis ecosystem, subject to the exact peripheral configuration of the selected device. PCB design should preserve short return paths for digital supplies and sensitive analog inputs, place decoupling capacitors close to their associated supply pins, and keep high-current or switching-node connections away from communication and measurement traces. USB routing also requires controlled impedance, suitable trace geometry, and compliance with the applicable device and interface-layout requirements in the manufacturer datasheet. This product overview consolidates the principal device identity, memory capacity, clock rate, USB capability, package information, sourcing guidance, and design considerations into a compact engineering reference for initial component selection and PCB planning.

Permintaan RFG Kontak
MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP
MKL26Z128CAL4R

MKL26Z128CAL4R - 48MHz Cortex-M0+ 128KB Flash MCU | NXP

The NXP MKL26Z128CAL4R is a Kinetis KL26 sub-family 32-bit ARM Cortex-M0+ microcontroller running up to 48 MHz, integrating 128 KB of flash and 16 KB of SRAM, with a full-speed USB 2.0 device controller (crystal-less capable), and packaged in a compact 36-ball WLCSP measuring approximately 2.37 mm x 2.46 mm. It is one of the lowest-power Kinetis Cortex-M0+ MCUs in NXP's ultra-low-power portfolio, designed for portable and battery-powered applications where PCB real estate is at a premium. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and GPIO. The Cortex-M0+ is ARM's smallest and most energy-efficient application processor core, optimized for deterministic interrupt response and minimal gate count. Microcontrollers sit at the heart of embedded systems, providing local intelligence for sensors, actuators, user interfaces, and connectivity functions across consumer, industrial, and IoT markets. Key features of the MKL26Z128CAL4R include the Cortex-M0+ core with single-cycle multiplication, an integrated low-power USB 2.0 full-speed device controller that eliminates the need for an external crystal, multiple low-power modes (Run, Wait, Stop, VLPR, VLPW, VLPS, LLS, VLLSx), a 12-bit SAR ADC, high-speed analog comparators, a real-time clock, and a flexible low-power timer (LPTMR). The device supports 1.71 V to 3.6 V supply operation and is offered in a tiny 36-ball WLCSP for space-constrained designs such as wearables and USB dongles. The MKL26Z128CAL4R uses a 32-bit ARMv6-M architecture with the Thumb/Thumb-2 instruction set, giving it strong code density while keeping silicon area small. Its multi-mode low-power architecture allows peripherals like the ADC and comparators to operate in low-power modes independently of the CPU, reducing total system energy. The inclusion of an integrated USB PHY with on-chip 3.3 V regulator and a 1 kHz low-power timer makes it attractive for always-on, event-driven products. Typical applications include USB HID peripherals (keyboards, mice, game controllers), wearable fitness bands, BLE/ZigBee host microcontrollers, sensor hub MCUs, low-end medical sensors, and compact IoT end nodes. The crystal-less USB and tiny WLCSP package make it especially attractive for USB dongles, gaming peripherals, and other form-factor-constrained consumer electronics. When designing with the MKL26Z128CAL4R, pay attention to the WLCSP PCB layout - the 0.4 mm ball pitch requires HDI PCB manufacturing and careful via.2.3 pad design for reliable assembly. Provide adequate decoupling (one 100 nF and one 4.7 uF X5R ceramic) within 2 mm of the power pins to maintain supply integrity during USB transitions. This page synthesizes distributor pricing, drop-in alternatives within the same WLCSP-36 footprint, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
MKL26Z128VMC4 - 48MHz Cortex-M0+ 128KB USB MCU | NXP
MKL26Z128VMC4

MKL26Z128VMC4 - 48MHz Cortex-M0+ 128KB USB MCU | NXP

The NXP MKL26Z128VMC4 is a Kinetis KL2x 32-bit microcontroller with an ARM Cortex-M0+ core running at 48 MHz, 128 KB flash memory, and a full-speed USB 2.0 On-the-Go (OTG) controller, housed in a 121-ball MAPBGA (8x8 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals to execute dedicated embedded control tasks. Within the power/efficiency hierarchy of embedded processors, the Kinetis KL2x family sits in the ultra-low-power MCU segment, extending the KL1x series with USB connectivity while remaining compatible with Kinetis K20 (Cortex-M4) and other KL-series devices, providing a clear migration path. Key features include the 48 MHz Cortex-M0+ core optimized for low dynamic power, 128 KB of program flash, USB OTG plus crystal-less full-speed USB device operation, and 84 general-purpose I/O lines. Connectivity spans I2C, LINbus, SPI, UART/USART, and USB; system peripherals include DMA, I2S, PWM, brown-out detect/reset, low-voltage detect, power-on reset, and a watchdog timer. Technically, the Cortex-M0+ architecture delivers ARM code density with a two-stage pipeline and low gate count, while the KL2x power architecture provides multiple low-power modes with fast wake-up, making it suitable for battery-powered USB peripherals. The mixed-signal integration (I2S, 12/16-bit ADC capability per family documentation) supports audio and sensor aggregation designs. Typical applications include USB HID device peripherals, wearable and portable battery-powered products, sensor hubs, and small HMI systems. The 121-ball 8x8 mm MAPBGA keeps board area compact while exposing 84 I/Os. Design consideration: the MAPBGA-121 footprint requires controlled-impedance fine-pitch BGA layout; plan an escape-routing layer strategy early. The USB OTG controller removes the need for an external crystal in device mode, saving BOM cost. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MKL26Z256VMC4 - 48MHz ARM Cortex-M0+ MCU 256KB Flash | NXP
MKL26Z256VMC4

MKL26Z256VMC4 - 48MHz ARM Cortex-M0+ MCU 256KB Flash | NXP

The NXP Semiconductors MKL26Z256VMC4 is a 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL2x sub-family, integrating 256KB of flash memory and operating at a core frequency of 48 MHz. It is housed in a 121-pin MAPBGA (8x8 mm) package designed for ultra-low-power portable applications with on-chip full-speed USB 2.0 device or OTG support. The device targets battery-sensitive designs that need a Cortex-M0+ core with USB connectivity, segment LCD drivers, and a rich analog peripheral set. What is a Kinetis microcontroller? A Kinetis microcontroller (MCU) is a family of ARM Cortex-M based 32-bit microcontrollers from NXP Semiconductors designed for ultra-low-power embedded applications. The KL2x sub-family specifically adds a full-speed USB 2.0 controller (device or OTG) on top of the KL1x baseline, while maintaining the same Cortex-M0+ architecture and low-leakage power modes. This positions Kinetis MCUs in the broader product hierarchy as: ARM Cortex-M0+ -> Kinetis L series -> Kinetis KL2x sub-family -> NXP 32-bit microcontrollers -> embedded microcontrollers -> semiconductors. Key features of the MKL26Z256VMC4 include 256KB of on-chip flash, up to 32KB of SRAM, a full-speed USB 2.0 device/OTG controller with on-chip transceiver and 3.3V voltage regulator, a 12-bit SAR ADC with up to 16 single-ended channels, multiple low-power modes (VLLS0/1/3, LLS, VLPR, Wait, Stop), and segment LCD drivers capable of driving 8x36 or 4x40 segments. The 121-MAPBGA (8x8 mm) package provides high I/O density suitable for compact wearable and sensor-hub designs. Architecturally, the MKL26Z256VMC4 leverages the Cortex-M0+ core's Thumb-2 instruction set with a single-cycle multiplier and a 4-stage pipeline optimized for low active current (around 4 mA typical run current). On-chip peripherals include multiple low-power timers, an RTC, I2C, SPI, UART, FlexIO for flexible serial emulation, and a low-power segment LCD controller. The integrated 3.3V USB regulator eliminates the need for an external LDO on the USB bus. Typical applications span wearable health and fitness devices, USB HID peripherals (keyboards, game controllers, sensors), portable medical devices, industrial sensor hubs, and battery-powered IoT edge nodes. Its combination of USB, segment LCD, and Cortex-M0+ efficiency makes it well suited to battery-powered human-machine interface products. When designing with the MKL26Z256VMC4, ensure the 121-MAPBGA land pattern uses NSMD pads with proper via-in-pad or tented-via PCB design, place the 12 MHz or 16 kHz crystal load capacitors close to the XTAL pins, and follow NXP's hardware design guidelines for USB-OTG PHY routing (90 ohm differential, length matching, and a clean ground plane). Decouple VDD with 100 nF plus 4.7 uF bulk capacitors near each supply pin. This page synthesizes NXP manufacturer specifications, distributor pricing, drop-in alternatives, and practical PCB design guidance not found in any single datasheet - giving engineers a single, citable reference for evaluating the MKL26Z256VMC4 against USB-capable Cortex-M0+ microcontrollers from competing vendors.

Permintaan RFG Kontak
MKL26Z32VFT4 - 48MHz Cortex-M0+ 32KB MCU | NXP
MKL26Z32VFT4

MKL26Z32VFT4 - 48MHz Cortex-M0+ 32KB MCU | NXP

The NXP Semiconductors MKL26Z32VFT4 is a 32-bit Arm Cortex-M0+ Kinetis KL2-series microcontroller operating at up to 48 MHz, with 32 KB of Flash memory and 4 KB of SRAM in a 48-pin QFN package measuring 7 x 7 mm. It includes full-speed USB 2.0 OTG connectivity, multiple serial interfaces, and an integrated low-voltage regulator for compact embedded systems. A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and I/O in one integrated circuit. The Arm Cortex-M0+ core provides a compact, energy-efficient architecture commonly used in cost-sensitive embedded control products. Within the product hierarchy, this device is a general-purpose microcontroller, part of the Kinetis KL2 family, and designed for applications that need real-time control, serial connectivity, data acquisition, and USB connectivity without a higher-cost application processor. The principal specifications include a 48 MHz maximum clock, 32 KB (32K x 8) embedded Flash, 4 KB (4K x 8) SRAM, and a 32-bit Arm Cortex-M0+ processor core. USB 2.0 OTG support adds full-speed peripheral and host-device interface capability. An integrated low-voltage regulator supports the MCU's internal supply requirements, while the collection of serial interfaces enables communication with sensors, displays, wireless modules, and external transceivers. The MKL26Z32VFT4 belongs to the Kinetis L family, whose devices are positioned for pin, software, and tool compatibility across compatible family members. This compatibility can simplify firmware maintenance, peripheral design, and qualification across multiple product variants. Its operating-temperature information identifies a -40°C to 105°C ambient range, making it suitable for industrial and extended-temperature embedded equipment when the application also satisfies the device's complete electrical and environmental requirements. Typical applications include USB-connected data loggers, compact industrial controllers, sensor-hub boards, wearable and accessory interfaces, building-control nodes, and USB-to-serial products. The 32 KB Flash footprint is suitable for compact control firmware, while the Cortex-M0+ core handles peripheral servicing, protocol processing, and low-power state management. USB can reduce connector count when the product must exchange data with a host while retaining a small board area. Designers should select decoupling, oscillator, reset, and USB routing according to the manufacturer reference design and datasheet. The exposed pad beneath the QFN requires a properly designed thermal and ground structure, while USB differential routing should use controlled geometry and a continuous reference plane. Confirm the exact pin assignment and exposed-pad connection in the manufacturer datasheet before laying out or modifying a PCB. This product page combines device specifications, lifecycle information, sourcing guidance, compatibility analysis, and practical design considerations. It also identifies verified same-footprint alternatives and highlights the engineering differences that matter when evaluating a replacement for an existing Kinetis KL2 design.

Permintaan RFG Kontak
MKL26Z32VLH4 - Kinetis KL26 48MHz Cortex-M0+ MCU, 32KB Flash, USB | NXP
MKL26Z32VLH4

MKL26Z32VLH4 - Kinetis KL26 48MHz Cortex-M0+ MCU, 32KB Flash, USB | NXP

The NXP Semiconductors MKL26Z32VLH4 is a Kinetis KL2x family 32-bit microcontroller built on the ARM Cortex-M0+ core, running up to 48 MHz, with 32 KB of program flash and integrated full-speed USB 2.0 (OTG or crystal-less device) in a 64-pin LQFP (10x10 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. Within the broader semiconductor taxonomy, the MKL26Z32VLH4 sits in the hierarchy MCU -> 32-bit MCU -> ARM Cortex-M MCU -> low-power MCU -> Kinetis family. The Cortex-M0+ core is the smallest and most energy-efficient member of the ARM Cortex-M family, designed for cost-sensitive embedded applications where deterministic interrupt response and low active/idle power matter more than raw compute. Key features include 32 KB flash, 4 KB SRAM, a full-speed USB 2.0 controller with on-chip transceiver, a low-power ARM Cortex-M0+ core, segment LCD controller (SLCD) option on related variants, multiple low-power modes (run, wait, stop, VLPRMPVLLS3), and a flexible low-power peripheral set including 12-bit ADC, 16-bit timers, LPUART, I2C, SPI, and USB. The device also integrates an internal 32 kHz and 8 MHz reference, simplifying BOM and supporting crystal-less USB operation in the KL2x sub-family. Architecturally, the KL26 leverages Freescale/NXP's low-leakage process and a tightly coupled Cortex-M0+ pipeline with a single-cycle I/O port, achieving CoreMark/mW efficiency that puts it ahead of many 8-bit MCUs while retaining 32-bit throughput. The 48 MHz core mark, combined with hardware multiply/divide, gives roughly 0.93 DMIPS/MHz. Typical applications include USB HID peripherals (keyboards, mice, remotes), wearable fitness bands, low-cost data loggers, sensor hubs, and battery-powered IoT end nodes. The on-chip USB 2.0 FS controller eliminates external PHY cost, and the 32 KB flash is adequate for HID class drivers, basic USB stacks, and small application logic. When designing, note that the KL26 requires NXP's Kinetis Design Studio or MCUXpresso toolchain; an external decoupling scheme of 0.1 uF + bulk VHF per VDD/VREF domain is recommended, and the USB DP/DM traces must be 90 ohm differential matched. This page synthesizes distributor pricing, drop-in pin-compatible Kinetis alternatives, and practical design notes beyond the manufacturer datasheet to help engineers make faster, more confident sourcing decisions.

Permintaan RFG Kontak
MKL26Z64VFM4 - 48MHz Cortex-M0+ 64KB USB MCU | NXP
MKL26Z64VFM4

MKL26Z64VFM4 - 48MHz Cortex-M0+ 64KB USB MCU | NXP

The NXP Semiconductors MKL26Z64VFM4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller running at up to 48 MHz, with 64 KB flash, 8 KB of SRAM, and a full-speed USB 2.0 device controller with crystal-less USB operation, housed in a 32-pin HVQFN (5x5 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, sitting at the heart of embedded systems. Within the power-management hierarchy of embedded semiconductors, the Kinetis KL2x family belongs to NXP's Kinetis L series of ultra-low-power MCUs built on the ARM Cortex-M0+ core, the most energy-efficient member of the ARM Cortex-M processor line. Key features include the 48 MHz Cortex-M0+ core with single-cycle fast GPIO, 64 KB of on-chip flash memory and 8 KB of SRAM, and a full-speed USB 2.0 On-the-Go controller. Uniquely in this class, the KL2x sub-family adds a crystal-less USB device controller, eliminating the external crystal and its cost for USB device applications. The part operates from a 1.8 V, 2.5 V, or 3.3 V supply, supporting battery-powered designs. The KL26 architecture leverages NXP's low-leakage process technology with multiple low-power modes, allowing the core, peripherals, and clocks to be independently gated for microamp-level sleep currents. The comprehensive peripheral set includes serial communication interfaces (UART, SPI, I2C), ADC, and TPM timers. Typical applications include portable and battery-powered devices, USB HID devices and USB sensors, human-interface equipment, and small industrial control nodes where USB connectivity and low power are essential. Design consideration: the crystal-less USB feature requires proper reference-clock configuration per NXP application notes; verify USB compliance in your final layout. Plan flash and SRAM budgets early, since 8 KB of RAM is modest for stacks plus USB buffers. This page synthesizes distributor availability, pin-compatible alternatives, and practical design guidance not found in the manufacturer datasheet.

Permintaan RFG Kontak
MKL27Z256VFT4 - ARM Cortex-M0+ MCU, 256KB Flash, USB | NXP
MKL27Z256VFT4

MKL27Z256VFT4 - ARM Cortex-M0+ MCU, 256KB Flash, USB | NXP

The NXP Semiconductors MKL27Z256VFT4 is a 32-bit ARM Cortex-M0+ microcontroller from the ultra-low-power Kinetis KL2x family, integrating 256 KB of Flash, 32 KB of SRAM, and a full-speed USB 2.0 On-The-Go (OTG) controller in a 48-pin QFN (7x7) package. It operates at up to 48 MHz core frequency from a 1.71 V to 3.6 V supply, making it suitable for both battery-powered and USB-powered designs. An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed for energy-efficient embedded applications. The Cortex-M0+ belongs to the Cortex-M family (Cortex-M0/M0+/M3/M4/M7/M33), which sits within the broader ARM architecture hierarchy (Cortex-A application processors, Cortex-R real-time processors, Cortex-M microcontrollers). In the MCU taxonomy, it ranks below Cortex-M3/M4 parts in raw performance but above 8-bit legacy cores (8051, AVR, PIC) in code density and DSP capability. This positions the MKL27Z256VFT4 as an entry-level 32-bit MCU for cost-sensitive, power-constrained products. Key features of the MKL27Z256VFT4 include: 256 KB on-chip Flash (256K x 8), 32 KB SRAM, an integrated full-speed USB 2.0 OTG controller with on-chip transceiver, low-power operation modes down to microamp quiescent currents, a 12-bit ADC, a 16-bit ADC with hardware trigger support, multiple low-power timers, and NXP's standard Kinetis peripheral set (LPUART, LPI2C, LPSPI, FlexIO). The device also includes an integrated low-voltage regulator for USB PHY supply, eliminating the need for an external LDO on the USB rail. Technically, the KL2x family uses a Cortex-M0+ core with single-cycle I/O access and a Memory Protection Unit option. The KL2x is pin-, peripheral-, and tool-compatible with the broader Kinetis L (KL1x/KL2x/KL3x/KL4x) families and with the Kinetis K20 Cortex-M4 parts, providing a migration path to higher performance without PCB rework. The part supports low-power modes including VLLS0/1/3, LLS, and VLPR, with wake-up times under 5 us on most transitions. Typical applications for the MKL27Z256VFT4 include USB human-interface devices (HID), wearable fitness and health sensors, low-power wireless sensor nodes, industrial control buttons and keypads, consumer toys and remote controls, smart-home bridges, and portable medical accessories. Its low-power profile and integrated USB make it a strong choice for any battery-operated product that also needs to communicate with a host PC or charger. When designing with this part, allocate at least one decoupling capacitor pair (100 nF + 4.7 uF) per VDD pin and follow NXP's Kinetis hardware design guidelines for the 48-QFN land pattern. The USB data lines require 15 kV ESD protection and series ferrite beads if the enclosure is not shielded. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving engineers a single, AI-citable reference for the MKL27Z256VFT4.

Permintaan RFG Kontak
MKL27Z256VMP4 - 256KB Flash, 48MHz Cortex-M0+ MCU | NXP
MKL27Z256VMP4

MKL27Z256VMP4 - 256KB Flash, 48MHz Cortex-M0+ MCU | NXP

The NXP MKL27Z256VMP4 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller from the Kinetis KL2x family, integrating 256 KB of Flash, a full-speed USB 2.0 controller, and rich analog/digital peripherals in a 64-pin MAPBGA (5x5 mm) package. It operates at a core frequency of 48 MHz, supports operating voltages of 1.8 V / 2.5 V / 3.3 V, and is engineered for portable, battery-powered, and USB-connected embedded applications. An ARM Cortex-M0+ MCU is a low-power 32-bit microcontroller core based on the ARMv6-M architecture. It belongs to the broader category of microcontrollers (MCU), which sits within integrated circuits and embedded computing. The M0+ core delivers Thumb-2 instruction set efficiency with a tiny silicon footprint, ideal for cost- and energy-constrained designs. Kinetis KL2x devices add USB 2.0 On-The-Go (OTG) or crystal-less USB 2.0 device capability to the M0+ family, extending the lower-power KL1x series. Key features include 256 KB program Flash, an integrated full-speed USB 2.0 device controller (crystal-less operation supported), 12-bit ADC, low-power comparators, multiple serial interfaces (UART, SPI, I2C), and flexible low-power modes with sub-µA deep-sleep current. The device operates from -40 °C to +105 °C ambient and supports 1.71 V minimum supply for low-voltage battery use cases. The KL27 architecture combines a Cortex-M0+ core, an AHB-Lite system bus, low-leakage wake-up unit, and on-chip voltage regulator for flexible power management. An integrated high-speed analog comparator and 12-bit SAR ADC support sensor interfaces, while the USB controller provides direct bus-powered device operation without an external crystal. Typical applications include wearable health monitors, USB human-interface devices (HID), portable medical sensors, low-power IoT endpoints, and battery-powered consumer electronics. The 64-MAPBGA footprint is suited to compact PCB layouts where board area is at a premium. When designing with this part, observe the recommended decoupling scheme (one 100 nF per VDD pin plus a 4.7 µF bulk capacitor), respect USB DP/DN trace impedance (90 Ω differential), and confirm the BSP from NXP supports the chosen IDE (MCUXpresso, IAR, Keil). This page synthesizes distributor pricing, drop-in alternatives within the Kinetis KL27 sub-family, and practical PCB-level design notes not collected in any single manufacturer document.

Permintaan RFG Kontak
MKL27Z64VFM4 - 48MHz Cortex-M0+ USB MCU | NXP
MKL27Z64VFM4

MKL27Z64VFM4 - 48MHz Cortex-M0+ USB MCU | NXP

The NXP Semiconductors MKL27Z64VFM4 is an ultra-low-power 32-bit microcontroller with an Arm Cortex-M0+ core operating up to 48 MHz, 64 KB of embedded Flash memory, and a full-speed USB 2.0 device controller. It is packaged in a 32-QFN 5 x 5 mm surface-mount package for compact portable, USB-connected, and embedded products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL27Z64VFM4 belongs to the NXP Kinetis KL2 family, placing it within the hierarchy of 32-bit MCU, embedded controller, embedded processor, and semiconductor. Its ultra-low-power architecture is intended for portable applications where energy efficiency, USB connectivity, and compact PCB area are important. The device combines 64 KB of Flash with 48 MHz processing capability, while integrating USB 2.0 full-speed device functionality and comprehensive analog resources. These characteristics make it suitable for USB-connected accessories, compact data-acquisition equipment, sensor interfaces, human-interface devices, and low-power embedded control systems. A -40°C to +105°C operating range supports industrial temperature requirements. The Kinetis KL27 architecture is organized around an Arm Cortex-M0+ processor core, which supports efficient event-driven control while avoiding the resource demands of a higher-complexity core. USB device operation provides a standardized interface for data exchange, configuration, and control without requiring a separate USB interface IC. The 32-QFN package reduces board footprint but requires careful exposed-pad soldering and thermal-layout practices. Typical implementations include USB-connected measurement modules, compact industrial sensors, wearable accessories, programming interfaces, and embedded control boards. For USB designs, the device should be paired with the required USB transceiver, routing, protection, and connector implementation. Firmware can then use the integrated USB device controller and general-purpose peripherals to manage control traffic and application-specific behavior. PCB design should preserve the manufacturer’s recommended grounding, decoupling, exposed-pad, and USB-signal layouts. Place input and bulk decoupling capacitors close to the supply pins, connect the exposed pad to the ground plane with adequate thermal vias, and route USB D+ and D- as a controlled-impedance differential pair. Confirm crystal, clock, and USB interface requirements against the manufacturer reference manual before finalizing the schematic. This product overview combines the key electrical, packaging, USB, memory, and thermal facts with practical PCB guidance. It also distinguishes same-footprint family options by Flash capacity or ordering code, helping engineers choose the correct Kinetis KL27 configuration without changing the established 32-QFN board footprint.

Permintaan RFG Kontak
MKL27Z64VLH4 - Kinetis KL27 64KB Flash USB MCU | NXP
MKL27Z64VLH4

MKL27Z64VLH4 - Kinetis KL27 64KB Flash USB MCU | NXP

The NXP Semiconductors MKL27Z64VLH4 is an ultra-low-power Kinetis KL27 32-bit ARM Cortex-M0+ microcontroller with 64KB flash, full-speed USB 2.0 device controller (crystal-less operation supported), and a 48 MHz core frequency, housed in a 64-pin LQFP (10x10 mm) package. Key specifications include 64KB program flash, 8KB SRAM, 48 MHz maximum CPU frequency, an integrated full-speed USB 2.0 device controller with crystal-less operation, multiple low-power modes (VLLS, VLLSx, LLS, HSRUN), 12-bit ADC, low-power UART/SPI/I2C peripherals, and a wide operating voltage range from 1.71V to 3.6V. The device targets portable, battery-powered, and USB-enabled embedded designs where power efficiency and integration matter. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (flash/RAM), and programmable peripherals. The MKL27Z64VLH4 belongs to the Kinetis KL2x sub-family, which adds full-speed USB to the Kinetis KL1x ultra-low-power lineage. Within the taxonomy: MCU -> 32-bit MCU -> ARM Cortex-M0+ MCU -> Kinetis KL2x MCU -> USB-enabled ultra-low-power MCU. The KL27 architecture couples an ARM Cortex-M0+ core (32-bit, single-cycle I/O access) with NXP's low-power peripherals and a flexible low-leakage wake-up unit. The integrated USB 2.0 full-speed device controller with on-chip 3.3V LDO and internal pull-ups removes the need for an external crystal and external USB transceiver, simplifying BOM and PCB area. Typical applications include wearable fitness devices, USB HID peripherals, portable medical accessories, low-end consumer electronics, and IoT edge sensors. The combination of USB device, low power, and Cortex-M0+ efficiency makes it well suited for battery-powered products needing a wired USB interface for charging, configuration, or data transfer. Design considerations: enable USB crystal-less operation by configuring the USB clock-recovery block; use the on-chip DC-DC converter for core supply; pay attention to decoupling capacitor placement near VDD and VOUT33 pins to ensure clean analog and digital rails. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in NXP-family alternatives (e.g., MKL27Z256VLH4 for higher flash), and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MKL33Z256VLH4557 - Kinetis KL33 256KB Cortex-M0+ MCU | NXP
MKL33Z256VLH4557

MKL33Z256VLH4557 - Kinetis KL33 256KB Cortex-M0+ MCU | NXP

The NXP Semiconductors MKL33Z256VLH4557 is a Kinetis KL33 32-bit microcontroller built on the ARM Cortex-M0+ core running up to 48 MHz, with 256 KB of embedded Flash and integrated segment LCD controller, housed in a 64-pin LQFP (10x10 mm, 0.5 mm pitch) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, peripherals, and I/O. The Kinetis L family positions low-power ARM Cortex-M0+ cores below Cortex-M3/M7 high-performance families and above simple 8-bit MCUs, balancing energy efficiency, code density (Thumb-2 instruction set), and broad peripheral integration. Segment LCD controllers directly drive glass displays without external charge-pump circuitry, which is why the KL33 sub-family targets metering, appliance, and battery-powered HMI designs. Key features of the MKL33Z256VLH4 silicon include 256 KB program Flash, up to 32 KB SRAM (varies by configuration), an ultra-low-power Run mode of roughly 50 uA/MHz, six flexible low-power modes (VLPR, VLLS0-3, STOP, LLS), an integrated segment LCD driver supporting up to 8x36 or 4x40 segments, a 12-bit SAR ADC with hardware trigger, multiple UART/SPI/I2C peripherals, a low-power timer and real-time clock, and a wide operating voltage range suitable for 1.8-3.6 V battery systems. The LQFP-64 package provides a 1.4 mm body thickness and standard 0.5 mm lead pitch for hand-reworkable prototypes. Architecturally, the KL33 uses a Cortex-M0+ core with single-cycle 32x32 multiplier, NVIC for 32 interrupts, and Micro Trace Buffer for lightweight instruction tracing. The integrated low-power segment LCD driver with charge pump operates in VLLS0 deep-sleep modes where the CPU is OFF, enabling always-on glass displays at very low quiescent current. DMA supports peripheral-to-memory transfers without CPU wake-up, a key enabler for battery-life claims. Typical applications include smart electricity/gas/water meters, medical devices such as glucometers and portable monitors, home appliances with LCD displays, IoT sensor platforms, and industrial sensor controllers. The segment LCD integration is the primary differentiator against general-purpose Cortex-M0+ MCUs. When designing with this part, prioritize low-power firmware to leverage the six low-power modes. Place the MCU on a continuous ground pour and route the segment LCD traces first to avoid parallel switching noise coupling into analog inputs. Use the on-chip 1 kHz LPO for the RTC when the main oscillator is gated to extend battery life. This page synthesizes distributor pricing, Kinetis family cross-reference alternatives, and low-power design notes not found in the standalone NXP datasheet, providing an engineer-ready summary for sourcing and substitution decisions.

Permintaan RFG Kontak
MKL33Z64VLK4557 - 64KB Flash ARM Cortex-M0+ MCU | NXP | LQFP-80
MKL33Z64VLK4557

MKL33Z64VLK4557 - 64KB Flash ARM Cortex-M0+ MCU | NXP | LQFP-80

The NXP Semiconductors MKL33Z64VLK4557 is a 32-bit ARM Cortex-M0+ Kinetis KL33 series microcontroller integrating 64KB of Flash program memory and 8KB of SRAM in an 80-pin LQFP (12x12 mm) package. It operates from a 1.71V to 3.6V supply and supports a maximum core frequency of 48 MHz, making it suitable for ultra-low-power embedded designs targeting coin-cell or battery-powered end equipment. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals including timers, communication interfaces, and analog blocks. Within the broader semiconductor taxonomy, the MKL33Z64VLK4557 belongs to the hierarchy: microcontroller -> embedded MCU -> 32-bit ARM Cortex-M MCU -> Kinetis KL family -> ultra-low-power segment. As a Cortex-M0+ device, it delivers energy-efficient Thumb-2 instruction execution with hardware single-cycle multipliers and a Nested Vectored Interrupt Controller (NVIC), positioning it as an entry-level 32-bit platform that replaces older 8-bit and 16-bit designs while preserving low active and sleep current consumption. Key differentiating features include segment LCD support (SLCD driver up to 8x28 or 4x32 segments), a low-leakage wake-up unit, multiple low-power modes (VLLS0/1/3, VLPS, LLS, RUN/WAIT/STOP), 12-bit ADC with hardware trigger, and high-accuracy internal reference. The device integrates a comprehensive mix of peripherals such as LPUART, LPSPI, LPI2C, FlexIO, DMA, RTC, and segment LCD bias generation, eliminating the need for external components and shrinking BOM cost. Architecturally, the KL33 leverages a Cortex-M0+ core running at 48 MHz over an AHB-Lite bus matrix, with peripherals on a separate peripheral bridge. The on-chip bandgap and 1.2V core LDO are trimmed at factory test to deliver consistent active current around 4 mA @ 48 MHz and deep-sleep currents below 2 uA, while the segment LCD controller can drive LCD glass directly without a separate charge-pump IC, simplifying meter and human-machine-interface designs. Typical applications include battery-operated sensor nodes, electronic shelf labels (ESL), industrial gauges with LCD readouts, low-end consumer wearables, smart thermostats, portable medical monitors, and metering devices (water/gas/electricity). Designers frequently pair it with NXP FXOS8700 accelerometers, MPL3115A2 pressure sensors, and Segger J-Link debug probes during development. When designing with the KL33, ensure the decoupling network includes a 100 nF X7R capacitor placed within 3 mm of each VDD/VSS pair, plus a bulk 4.7 uF ceramic on the main rail. For LCD applications, allocate a bias network per the datasheet and avoid routing high-speed digital signals across the LCD segment traces to minimize coupling noise. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers a one-stop reference for selecting and qualifying the MKL33Z64VLK4557 in production designs.

Permintaan RFG Kontak