Sirkuit Terpadu

PIC18F25K42-E/SP

PIC18F25K42-E/SP - 32KB Flash 8-bit MCU | 28-SPDIP | Microchip

The Microchip Technology PIC18F25K42-E/SP is an 8-bit PIC18 microcontroller with 32 KB Flash, 2 KB RAM and 256 B EEPROM, packaged in a 28-pin SPDIP through-hole format. It belongs to the PIC18FxxK42 family and runs at up to 64 MHz internal clock, integrating 12-bit ADC2 with computation, vector interrupts, DMA, DAC, comparators, PWM, CWG, HLT, WWDT, SCAN/CRC, ZCD, PPS, UART, SPI and I2C peripherals on a single die. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), data memory (EEPROM), and peripheral interfaces. Within the broader semiconductor hierarchy, MCUs sit under microcontrollers -> embedded processors -> semiconductors. The PIC18F25K42 family specifically targets low-power, high-performance applications using Microchip's XLP (eXtreme Low Power) technology and Functional Safety (FuSa) capable peripherals. Key features of the PIC18F25K42-E/SP include: 32 KB self-programmable Flash with code protection, 2 KB SRAM with hardware-managed context saving, 256 B high-endurance EEPROM rated for 100k erase/write cycles, 12-bit ADC2 with up to 35 channels and post-processing math accelerator, multiple communication peripherals (UART, SPI, I2C with SMBus PMBus), and DMA controller for memory-to-memory transfers. The -E/SP suffix indicates the extended (E) temperature grade of -40C to +125C in a 28-SPDIP package. The device uses Microchip's enhanced mid-range core with a 16-bit instruction word and 8-bit data path, supporting C-compiler-friendly assembly with hardware multiply and divide. Vectored interrupts with priority levels and peripheral pin select (PPS) provide flexible routing for digital and analog peripherals, simplifying PCB layout. Power management features include idle/doze modes, peripheral module disable (PMD), and XLP sleep currents in the nanoampere range, making the part suitable for battery-powered and energy-harvesting applications. Typical applications for the PIC18F25K42-E/SP include low-power IoT sensor nodes, motor control for small BLDC and stepper drives, industrial control with functional safety diagnostics, consumer appliance control boards, and general-purpose embedded products requiring 28-pin DIP-friendly prototyping. The DIP package supports easy breadboarding and through-hole rework in low-volume production. When designing with this MCU, verify Vdd range (1.8V to 5.5V for F; 1.8V to 3.6V for LF variant), apply correct decoupling (100 nF + bulk cap near Vdd), and configure PPS carefully since the same peripheral can map to multiple I/O pins. Programming requires Microchip's MPLAB X IDE with XC8 compiler or compatible toolchains. This page synthesizes distributor pricing, drop-in alternative MPNs, application examples, and practical design notes that go beyond the manufacturer datasheet, giving engineers a faster path to part selection, BOM consolidation, and PCB layout decisions for PIC18F25K42-based designs.

Permintaan RFG Kontak

PIC18F25K42-E/SS

PIC18F25K42-E/SS - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18F25K42-E/SS is an 8-bit PIC18 microcontroller built on the XLP (eXtreme Low Power) platform, integrating 32 KB of Flash program memory, 2 KB of RAM and 256 bytes of EEPROM in a 28-pin SSOP package. It executes instructions at up to 64 MHz from the internal oscillator, includes a 12-bit ADC2 with computation engine, 5-bit DAC, multiple comparators, PWM modules, DMA, vector interrupts, and configurable logic cells (CLC) for hardware glue logic. An 8-bit microcontroller (MCU) is a programmable computing IC that executes instructions 8 bits at a time over an internal data bus. PIC18F devices sit in Microchip's mainstream PIC architecture hierarchy: 8-bit MCU -> PIC18 family -> PIC18FxxK42 sub-family -> low-power XLP platform -> semiconductor. Within an embedded system the MCU provides deterministic real-time control alongside sensors, power and connectivity peripherals, replacing discrete logic while consuming milliwatts of power. Key features include a 12-bit differential ADC2 supporting automatic averaging and threshold comparison, a hardware DMA controller that moves data between peripherals and memory without CPU intervention, configurable logic cells (CLC) that let designers implement state machines and signal conditioning in silicon, and Functional Safety (FuSa) features such as a dedicated Windowed Watchdog Timer and a CRC scanner. Two UART, two SPI and two I2C interfaces support simultaneous multi-bus connectivity for sensor, display and wireless-module attachment. The K42 architecture pairs the standard PIC18 RISC core with independent peripherals interconnected through the peripheral pin select (PPS) crossbar, allowing flexible remapping of digital functions to physical pins. The XLP technology delivers typical sleep currents in the nanoamp range, idle currents near 1 uA, and active currents around 200 uA/MIPS - the right combination for always-on battery applications that wake periodically to process data. Typical applications include low-power IoT sensor nodes, industrial control peripherals, consumer appliances, automotive body and accessory controllers, and USB-to-UART bridging or general digital control. The wide 2.3V-5.5V supply range also lets the part operate directly from a single-cell Li-ion battery or a regulated 3.3V/5V rail. A key design tip is to use the PPS re-mapping to free up board real estate: nearly every digital peripheral can be routed to multiple physical pins, simplifying PCB routing without changing the silicon. Always configure the watchdog timer for unattended applications to recover from firmware lock-ups.

Permintaan RFG Kontak

PIC18F25K42-I/MV

PIC18F25K42-I/MV - 8-Bit 64MHz XLP MCU 32KB Flash UQFN-28 | Microchip

The Microchip Technology PIC18F25K42-I/MV is an 8-bit PIC18 XLP microcontroller running at up to 64 MHz with 32 KB Flash, 2 KB SRAM and 256 B EEPROM, housed in a 28-pin UQFN (4x4 mm) package. It integrates 12-bit ADC2 with Computation, multiple DAC outputs, comparators, configurable logic cells (CLC), and Direct Memory Access (DMA), enabling efficient sensor and motor-control designs. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory, volatile data memory, and on-chip peripherals such as timers, ADC, communication interfaces and GPIO. The PIC18 family targets 8-bit embedded control and is widely adopted in industrial, consumer, automotive and IoT applications where deterministic behavior, low power, and rich peripherals matter more than raw CPU throughput. PIC18F25K42 specifically belongs to the low-power XLP family, which integrates nanoWatt XLP technology for deep sleep and active mode power optimization. Key features include 64 MHz operation, 12-bit ADC with up to 35 channels, multiple UART/SPI/I2C with DMA support, 5-bit DAC, comparators with hysteresis, CLCs that operate without CPU intervention, and a functional safety (FuSa) category classified by Microchip. The device targets 1.8 V to 5.5 V operation, supports extended (-40C to +125C) industrial temperature, and is offered with XLP idle/doze/peripheral module disable modes that cut active current to microampere ranges. Architecturally, the PIC18F25K42 uses an enhanced Harvard 8-bit core with a 16-bit instruction word, hardware multiplier, interrupt prioritization, and vectored interrupts. Core-independent peripherals such as CLC, PWM, NCO and the CRC/SCAN engine offload routine work from the CPU, while DMA paths between memory and peripherals reduce interrupt overhead. Programming is supported through MPLAB X IDE with XC8 compilers, and in-circuit debugging via standard 4-wire ICD. Typical applications include home appliances, IoT sensor nodes, low-power battery-powered devices, automotive body and lighting subsystems, industrial control, sensor signal conditioning, and motor/lighting control. The functional safety (FuSa) designation makes the part appealing to safety-related systems per IEC 61508 SIL 2/3 recommendations when paired with appropriate documentation. When designing with this MCU, allocate PCB area for the ICSP/programming header, provide adequate decoupling (100 nF plus 1-10 uF bulk), and respect the 1.8-5.5 V supply rails. Use the PPS (Peripheral Pin Select) feature to remap peripherals to pins, simplifying PCB layout and BOM reuse across PIC18F variants in the family. This page synthesizes distributor availability (8+ distributors), drop-in pin-compatible same-family variants, and engineering guidance gathered from Microchip's K42 family datasheet - content you will not find on a single datasheet or distributor listing page.

Permintaan RFG Kontak

PIC18F25K42-I/SO

PIC18F25K42-I/SO - 8-bit 64MHz 32KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F25K42-I/SO is a 64 MHz, 32 KB Flash, 2 KB SRAM, 256-byte EEPROM 8-bit PIC18 microcontroller in a 28-pin SOIC package, part of the PIC18(L)FxxK42 XLP family with Functional Safety (FuSa) hardware features. According to Microchip's PIC18F24/25K42 datasheet, the device integrates a 24-channel 12-bit ADC with Computation (ADCC), three UARTs, two SPI, two I2C, a DMA controller, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and CCP/PWM peripherals in a 7.50 mm wide 300-mil SOIC outline. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data bus. It combines a CPU, non-volatile program memory (Flash), volatile working memory (RAM), small non-volatile data memory (EEPROM), and a rich set of peripherals such as timers, ADC, communication ports and GPIOs. PIC18 is Microchip's high-performance 8-bit family; the K42 sub-family adds low-power XLP operation and modern peripherals like a 12-bit ADC with Computation (ADCC), DMA, Vector Interrupts, CWG, CLC, and a 5-bit DAC. In the taxonomy: 8-bit MCU -> microcontroller -> embedded computing -> semiconductor. Key features include 25 MIPS throughput at 64 MHz, 32 KB self-programmable Flash with 10 KB bootloader area, 2 KB SRAM, 256 bytes EEPROM, integrated temperature indicator, programmable CRC with memory scan, and nanoWatt XLP sleep currents in the nA range. The device operates from 1.8 V to 5.5 V, with the -I industrial temperature grade spanning -40 C to +85 C, while the -E grade spans -40 C to +125 C. Architecturally, the PIC18F25K42 uses an enhanced Harvard architecture with a 16-bit instruction word and 8-bit data path, a 31-level hardware stack, and a high-throughput instruction pipeline. The integrated DMA controller offloads data movement between peripherals and memory, freeing the core for application logic and improving deterministic real-time response. Typical applications include industrial sensor nodes, IoT edge devices, low-power battery-powered metering, automotive body and climate subsystems (using the E/SP or E/SS extended-grade variants in non-safety contexts), home appliances, and any Functional Safety design needing pre-certified diagnostics and FMEDA documentation. When designing with this device, verify the 28-pin SOIC package matches your PCB land pattern, and confirm whether you need the -I industrial grade (-40 to +85 C) or -E extended grade (-40 to +125 C) temperature variant. Use MPLAB X IDE with the MPLAB Code Configurator (MCC) and the XC8 compiler for software development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the bare datasheet, including a parameter-by-parameter comparison against same-brand K42 family variants and competing 8-bit MCUs.

Permintaan RFG Kontak

PIC18F25K42-I/SP

PIC18F25K42-I/SP - 32KB Flash 8-bit MCU 64MHz 28-SPDIP | Microchip

The Microchip Technology PIC18F25K42-I/SP is an 8-bit PIC microcontroller from the PIC18FxxK42 family running at 64 MHz, integrating 32 KB of Flash program memory, 2 KB of RAM, and 256 bytes of EEPROM in a 28-pin SPDIP through-hole package. The device is built on Microchip's eXtreme Low Power (XLP) technology platform and includes Functional Safety (FuSa) features, making it suitable for safety-critical applications requiring IEC 61508 SIL compliance documentation. The -I/SP suffix denotes the industrial temperature grade (-40C to +85C) and SPDIP package. An 8-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from on-chip memory and interfaces with peripherals through digital and analog I/O pins. Within the broader taxonomy, an MCU belongs to microcontrollers -> microprocessors -> semiconductors -> integrated circuits. The PIC18F architecture implements an enhanced 8-bit RISC-like instruction set with hardware multiplier and 16-bit wide Flash, providing better code density than baseline PIC16 devices while retaining the simple peripheral and deterministic interrupt model that characterizes the PIC family. Key features include a 12-bit ADC2 with computation, a 5-bit DAC, multiple comparators, configurable logic cells, Complementary Waveform Generator (CWG), and Zero-Cross Detect (ZCD) - giving the device an unusually rich set of analog and digital peripherals for an 8-bit MCU. Vectored interrupts, DMA, Peripheral Pin Select (PPS), and a Memory Access Partitioning (MAP) scheme provide system-level flexibility normally associated with 32-bit parts. The device also integrates a Windowed Watchdog Timer (WWDT) and CRC/SCAN hardware for functional safety. Typical applications include industrial sensor conditioning, motor control loops, IoT edge nodes, low-power remote controls, and functional-safety subsystems. The wide peripheral set allows a single chip to replace a typical MCU plus external op-amp and analog mux circuit. When designing, allocate decoupling capacitance (100 nF plus 10 uF bulk) close to VDD/AVDD pins, follow Microchip's SPDIP footprint (0.1 inch row pitch) for socket compatibility, and use ICD4 or PICkit 4 for debug. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SPDIP package, and engineering design notes that extend beyond the manufacturer datasheet, enabling faster BOM selection and procurement.

Permintaan RFG Kontak

PIC18F25K42-I/SS

PIC18F25K42-I/SS - 8-bit 64MHz 32KB Flash MCU 28-SSOP | Microchip

The Microchip PIC18F25K42-I/SS is an 8-bit microcontroller from the PIC18FxxK42 family, delivering 64 MHz CPU performance with 32 KB Flash, 2 KB SRAM, and 256 B EEPROM in a 28-pin SSOP package. The part carries the -I (industrial) temperature grade spanning -40C to +85C and integrates rich Core Independent Peripherals (CIPs), a 12-bit ADC with Computation (ADC2), Configurable Logic Cells (CLC), Direct Memory Access (DMA), and UART/SPI/I2C serial interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory, and peripheral subsystems on one die. PIC18F microcontrollers are 8-bit RISC-Harvard architecture devices in the broader PIC family, which sits hierarchically under microcontrollers -> embedded processors -> semiconductor devices. The K42 sub-family is the PIC18F24/25/45/46K42 line that introduces XLP (eXtreme Low Power) technology and Functional Safety (FuSa) diagnostics, positioning these parts at the high end of the 8-bit PIC portfolio. Key features include a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) sequences for advanced touch sensing, up to 256 bytes of EEPROM with high-endurance rating, hardware DMA that offloads data movement between peripherals and memory, and CLC blocks that let designers implement glue logic inside the MCU. The XLP idle/doze/sleep modes plus nanoWatt XLP peripherals enable typical sleep currents below 1 uA, which is essential for battery-powered nodes. Architecturally the device pairs a modified Harvard RISC core with a vectored interrupt controller (fixed-latency IVT) and a System Bus Arbiter that coordinates DMA, CPU, and CLC transactions without CPU intervention. The 64 MHz internal oscillator and PLL eliminate external crystals in most applications, while four 16-bit timers, two CCP modules, three ECCP modules (with PWM), and a CWG (Complementary Waveform Generator) provide flexible waveform synthesis for motor, lighting, and power-control loops. Typical applications include consumer appliances, IoT sensor nodes, touch-button human-machine interfaces, low-end motor control, LED lighting controllers, and functional-safety systems that benefit from the FuSa diagnostics. The combination of DMA + CLC + ADC2 allows a single 28-pin part to replace discrete logic and a small companion MCU in cost-sensitive designs. Design considerations: ensure the SSOP-28 land pattern follows IPC-7351 nominal density, place a 100 nF decoupling cap within 2 mm of each VDD pin, and reserve the MCLR pin through a 10 kohm pull-up for in-circuit serial programming (ICSP). The -I/SS variant operates from -40C to +85C; use the -E/SS extended grade for -40C to +125C automotive or industrial environments. This page synthesizes DigiKey and Mouser distributor pricing, verified drop-in alternatives from the PIC18FxxK40 and PIC18FxxK22 family, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25K42T-E/SSVAO

PIC18F25K42T-E/SSVAO - 32KB Flash 8-bit MCU, AEC-Q100 | Microchip

The Microchip Technology PIC18F25K42T-E/SSVAO is an 8-bit PIC18 microcontroller featuring 32KB of Flash program memory, 2KB of SRAM, and 256 bytes of EEPROM, housed in a 28-pin SSOP (5.30 mm / 0.209" width) package and qualified to the AEC-Q100 automotive standard. Operating from 2.3 V to 5.5 V supply and capable of executing instructions at up to 64 MHz, the part delivers roughly 16 MIPS while consuming only nanoWatt XLP sleep currents. It belongs to the PIC18(L)FxxK42 family of 28-/40-/48-pin low-power high-performance microcontrollers with XLP technology. An 8-bit microcontroller (MCU) is a single-chip computer built around a CPU with an 8-bit data path, on-chip Flash for program storage, RAM for variables, EEPROM for non-volatile data, and a rich peripheral set including timers, ADC, communication interfaces, and Core Independent Peripherals (CIPs). Within the broader taxonomy, the PIC18F25K42T-E/SSVAO belongs to: microcontroller -> embedded MCU -> PIC18 family -> PIC18 K-series -> PIC18(L)FxxK42 family -> 28-pin K42 sub-family -> automotive-grade (AEC-Q100) variants. This hierarchy is what distinguishes it from 16-bit dsPIC and 32-bit ARM Cortex-M competitors from other vendors. The key feature set includes a 12-bit differential ADC with Computation (ADC2), a 5-bit DAC, on-chip DMA, three analog comparators, a 16-bit PWM, four Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), CRC/Memory Scan, and Peripheral Pin Select (PPS) for flexible signal routing. CIPs let designers offload logic to hardware, reducing CPU wake events and extending battery life in always-on applications. On the architecture side, this MCU uses Microchip's enhanced mid-range 8-bit CPU core with a 16-bit instruction word and an 8-level hardware stack, paired with a Harvard bus that lets the CPU fetch from Flash while reading data from RAM. The XLP nanoWatt technology adds multiple idle/sleep modes and ultra-low-power peripherals such as RTCC, HLVD, and WWDT, enabling years of operation from a single coin cell when properly configured. Typical applications for the PIC18F25K42T-E/SSVAO span the automotive AEC-Q100 landscape: body controllers, sensor interfaces, LED lighting modules, HVAC actuators, BCM auxiliary functions, and LIN-connected nodes. Industrial and consumer variants in the same family address general-purpose motor control, IoT end nodes, and battery-powered sensing. When designing with this device, ensure proper decoupling (100 nF + bulk cap close to VDD/AVDD/VBAT) and configure unused pins as outputs low to minimize leakage. The PPS peripheral must be locked before entering sleep to avoid accidental peripheral remap after a watchdog reset. This page synthesizes distributor pricing, AEC-Q100 cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak

PIC18F25K42T-I/ML

PIC18F25K42T-I/ML - 32KB Flash 8-bit MCU 28-QFN | Microchip

The Microchip PIC18F25K42T-I/ML is an 8-bit PIC microcontroller with 32KB Flash, 2KB SRAM and 256B EEPROM, running up to 64MHz in a 28-pin QFN (6x6) package with exposed pad. It integrates core-independent peripherals, intelligent analog, and large memory in an XLP low-power architecture. Tape and reel packaging (T suffix). A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory and programmable I/O. The PIC18 family uses an enhanced 8-bit RISC Harvard architecture with a modified instruction set, suitable for embedded control from appliances to industrial sensor nodes. The PIC18F25K42 belongs to the K42 generation, which adds DMA, configurable logic cells (CLC), CWG, multiple PWM/CCP, and an analog companion including 12-bit ADC and 5-bit DAC. Key features include 32KB (16K x 16) Flash program memory, 2KB SRAM, 256B data EEPROM, 64MHz maximum clock, and an industrial -40C to +85C operating range. The device supports 2.5V/3.3V/5V operation, includes 10 timers, 2 DMA channels, CLC/CWG/HLT peripherals, and multiple serial interfaces. Functional Safety (FuSa) capability makes it suitable for safety-critical embedded designs. Architecturally, the K42 separates the analog and digital domains and uses a 16-level stack plus hardware multiplier for efficient C code. Core-independent peripherals offload tasks from the CPU, lowering latency and active time, which combined with XLP sleep currents extends battery life. Typical applications include IoT edge nodes, industrial sensor conditioning, home appliances, lighting and motor control, USB-to-UART bridges, and small graphical user interfaces. The wide operating voltage and rich peripheral set also suit automotive body and aftermarket modules. When designing, place a 100nF decoupling capacitor near each VDD pin and a bulk 10uF near the regulator output. Use the exposed pad (EP) for thermal relief and provide solid ground copper to improve ADC noise performance. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak

PIC18F25K42T-I/MV

PIC18F25K42T-I/MV - 8-bit MCU, 32KB Flash, 64MHz, 28-UQFN | Microchip

The Microchip Technology PIC18F25K42T-I/MV is an 8-bit PIC18 XLP microcontroller with 32KB Flash, 2KB RAM, and 256B EEPROM, operating at up to 64MHz, housed in a 28-pin UQFN (MV) 4x4 mm package. It integrates a 12-bit ADC2 with Computation, a 5-bit DAC, vector interrupts, DMA, configurable logic cells (CLC), complementary waveform generator (CWG), and peripheral pin select (PPS), delivering high functional density in a compact footprint. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path CPU, on-chip Flash program memory, RAM, EEPROM, and a rich set of peripherals. Within the broader classification, an MCU belongs to microcontrollers, then to embedded processors, then to semiconductors. The PIC18 family uses an enhanced Harvard RISC architecture with 16-bit instructions, giving the PIC18F25K42 family a balance of code density, deterministic interrupt response, and ease of programming in C or assembly. Key features include eXtreme Low Power (XLP) technology with nanoWatt sleep currents, multiple idle/doze/peripheral module disable modes, hardware DMA that offloads ADC and memory-to-memory transfers from the CPU, and functional-safety diagnostics including WWDT, CRC/SCAN, windowed watchdog, and hardware limit timer (HLT). It also offers up to 25mA source/sink on I/O, supporting direct LED drive. Typical applications include low-power IoT sensor nodes, battery-powered consumer devices, home appliances, industrial control and monitoring, LED lighting controllers, and automotive body electronics subsystems (via the automotive-grade PIC18F25K42T-I/MVVAO). The wide operating voltage range and rich peripheral set make it well-suited to mixed-signal designs. When designing with this device, pay attention to the UQFN-28 thermal pad layout. Place a low-impedance ground via array directly under the exposed pad, follow Microchip's UQFN land pattern exactly, and budget for 64MHz operation only across the full 2.3V-5.5V supply range. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a one-stop comparison resource for the PIC18F25K42 family.

Permintaan RFG Kontak

PIC18F25K50-E/SP

PIC18F25K50-E/SP - 8-bit USB MCU, 32KB Flash, 48MHz | Microchip

The Microchip Technology PIC18F25K50-E/SP is an 8-bit PIC18 microcontroller with integrated USB 2.0 full-speed transceiver, 32KB of Flash program memory, and 48MHz internal oscillator, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), working memory (RAM), and programmable I/O peripherals. PIC18 family microcontrollers use a 16-bit modified-Harvard architecture with 8-bit data bus, 31-level hardware stack, and a rich peripheral set including USB, ADC, PWM, and serial communication modules. They sit within the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC -> active component. Key features include 32KB Flash program memory with self read/write capability, 2KB RAM, 256 bytes EEPROM, 48MHz internal oscillator tunable from USB host clock (Active Clock Tuning), integrated USB 2.0 full-speed transceiver, 25 I/O pins with multiple interrupt-on-change sources, 10-bit ADC up to 14 channels, two CCP/ECCP modules, two comparators, and Master Synchronous Serial Port (MSSP) supporting SPI and I2C. The part belongs to Microchip's XLP (eXtreme Low Power) family with sleep currents down to ~20 nA typical. The PIC18F25K50 core uses a 16-bit instruction word with 8-bit data path, executes one instruction per 4 clock cycles, and supports hardware 8x8 multiply. The integrated USB module handles full-speed (12 Mbps) device/host/OTG operation with on-chip transceiver and internal pull-up, eliminating the external USB components normally required. Active Clock Tuning automatically trims the internal HFINTOSC against the USB host frame clock for accurate baud-rate generation without external crystals. Typical applications include USB peripherals (HID, CDC, MIDI, custom classes), USB-to-UART bridges, low-power sensor nodes, battery-powered consumer electronics, industrial control interfaces, and educational/development platforms. The wide 2.3V-5.5V supply range and low sleep current also suit solar-powered or energy-harvesting designs. When designing with this device, note that the '-E' suffix indicates the Extended (-40C to +125C) operating temperature grade. The SPDIP package is best for prototyping and through-hole assembly; for volume production, equivalent parts in SOIC/SSOP/QFN packages are available within the same PIC18F25K50 family. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that supplement the manufacturer datasheet for faster engineering evaluation.

Permintaan RFG Kontak

PIC18F25K50-I/ML

PIC18F25K50-I/ML - 8-Bit USB MCU, 32KB Flash, 28-QFN | Microchip

The Microchip PIC18F25K50-I/ML is an 8-bit PIC18 microcontroller with integrated USB 2.0 transceiver, 32 KB of Flash program memory, and XLP (eXtreme Low Power) technology in a 28-pin QFN (6x6 mm) package. It executes instructions at 200 ns, delivering up to 16 MIPS at 48 MHz, and includes 2 KB SRAM plus 256 B EEPROM. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The PIC18 family uses a RISC (Reduced Instruction Set Computer) architecture with 75 instructions, chosen over CISC for compact code density and deterministic timing. Within the PIC18F family, the 25K50 sits in the performance tier with USB on-chip, while larger variants in the 46K/56K/66K ranges add more memory; smaller 14K/24K parts drop the USB PHY. PIC18 belongs to Microchip's 8-bit line — distinct from 16-bit dsPIC and 32-bit SAM/CEC families, and runs at 2.5 V, 3.3 V, or 5 V. Key features include 24 channels of 10-bit ADC with up to 28 digital I/O pins, two analog comparators, two 8/16-bit timers plus two 16-bit timers, two CCP modules, an EUSART, dual I2C/SPI, and a full-speed USB 2.0 device with on-chip transceiver supporting up to 32 endpoints (16 bidirectional). The integrated 48 MHz internal oscillator eliminates external crystals for USB operation. XLP technology delivers typical nanoWatt sleep currents below 100 nA. Architecturally, the PIC18F25K50 uses a 16-bit instruction word with 8-bit data path, hardware multiplier, and a 31-level hardware stack. XLP adds ultra-low-power modules including RTCC, ultra-low-power watchdog, and ultra-low-power wake sources, making the part suitable for battery-powered USB HID, sensor hub, and IoT endpoint designs. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), USB-to-UART bridges, sensor hubs with USB enumeration, low-power data loggers, and industrial controls requiring customer USB connectivity. USB bus-powered devices particularly benefit from the integrated PHY and the 5 V-tolerant I/O. When designing with this part, plan the USB D+/D- routing as a 90-ohm differential pair on PCB and ensure the internal regulator (3.3 V or 5 V mode) decoupling follows Microchip guidance. XLP sleep modes require careful peripheral disable sequencing to achieve the datasheet's low quiescent current. This page synthesizes distributor pricing, drop-in alternatives from Microchip's own PIC18F catalog, and practical design notes that go beyond the manufacturer datasheet's typical application circuits.

Permintaan RFG Kontak

PIC18F25K50-I/SO

PIC18F25K50-I/SO - 32KB Flash USB MCU 48MHz 28-SOIC | Microchip

The Microchip Technology PIC18F25K50-I/SO is an 8-bit PIC18 microcontroller with 32KB Flash, 2KB RAM, and an integrated USB 2.0 Full-Speed transceiver, housed in a 28-pin SOIC (SO) package. It runs up to 48 MHz and operates from 2.5V to 5.5V on the PIC18 core with 8x8 hardware multiply. According to the verified Microchip product page, the part is in production and ships with XLP (eXtreme Low Power) technology for battery-aware designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripherals such as timers, ADC, communication ports, and I/O. The PIC18F25K50 belongs to the PIC18 family of RISC microcontrollers, which occupy the mid-tier of the PIC architecture hierarchy (PIC10/12/16 -> PIC18 -> PIC24/dsPIC -> PIC32). Its defining role is the addition of a hardware USB 2.0 Full-Speed device controller, eliminating the need for an external USB PHY in cost-sensitive embedded links. Key features include 32 KB self-read/write Flash, 2 KB RAM, 256 bytes EEPROM, a 10-bit ADC with up to 14 channels, two comparators, Enhanced Capture/Compare/PWM, two USART (one LIN-capable), SPI, I2C, and an internal 48 MHz oscillator tunable against the USB host clock for accuracy. The XLP nanoWatt technology provides sleep currents as low as a few nanoamperies for battery-backed USB devices. USB Suspend/Resume is supported for full USB-IF compliance. Typical applications include USB HID peripherals (keyboards, mice, game controllers), USB-to-UART bridges, low-cost data loggers, sensor interfaces, consumer toys, and industrial control nodes. The 48 MHz core plus USB makes the part well suited when designers need to host a CDC/HID/MSD stack without paying for an ARM Cortex-M0. When designing with this device, ensure the VUSB pin has the recommended 220 nF decoupling and the D+/D- traces are 90-ohm differential length-matched. The internal 48 MHz oscillator is trimmed at the factory, but active clock tuning from the USB host is recommended for jitter-sensitive isochronous endpoints. This page synthesizes drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25K50T-I/ML

PIC18F25K50T-I/ML - 32KB Flash USB MCU 28-QFN | Microchip

The Microchip Technology PIC18F25K50T-I/ML is an 8-bit PIC18 microcontroller delivering 48 MHz CPU performance, 32 KB Flash program memory, 2 KB RAM and a full-speed USB 2.0 device module in a 28-pin QFN (6x6 mm) package. The -T suffix indicates Tape & Reel packaging and the -I grade denotes the -40C to +85C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals on one die. PIC18 devices from Microchip follow a RISC Harvard architecture with separate program and data buses; the K50 family adds a USB 2.0 full-speed transceiver and Active Clock Tuning that locks the internal 48 MHz oscillator to the USB host frame timing, eliminating the need for an external crystal in many USB applications. Key features include 32 KB self-read/write Flash, 256 bytes of integrated EEPROM, a hardware 8x8 multiplier, two USART/SPI/I2C modules plus a dedicated MSSP for I2C/SPI, a 10-bit ADC with up to 14 channels, and eXtreme Low Power (XLP) sleep currents. The integrated USB 2.0 module supports control, interrupt, bulk and isochronous transfers for CDC/HID/MSC device classes without external transceiver hardware. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), USB-to-UART bridge dongles, USB CDC virtual COM ports, USB-capable sensor nodes, low-power battery-powered instruments, and small appliances with USB firmware upgrade ports. When migrating from PIC18F24K50 or PIC18F26K50 designs the pin-out is preserved within the 28-QFN package. A practical design tip: route the D+/D- USB differential pair with 90-ohm differential impedance and keep total length below 50 mm to meet USB 2.0 signal-quality compliance; Active Clock Tuning only operates while the USB module is active. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25K50T-I/SO

PIC18F25K50T-I/SO - 32KB Flash USB 8-bit MCU 48MHz SOIC-28 | Microchip

The Microchip Technology PIC18F25K50T-I/SO is a high-performance 8-bit PIC microcontroller from the PIC18 XLP 18K family, integrating a full-speed USB 2.0 transceiver and 32 KB of Flash program memory in a 28-pin SOIC package. The 'T' suffix denotes tape-and-reel packaging, while 'I' indicates the industrial -40C to +85C temperature range and 'SO' specifies the 300-mil 28-SOIC footprint. The CPU runs up to 48 MHz delivering 16 MIPS throughput from an enhanced RISC architecture, with 200 ns instruction execution. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU, RAM, Flash program memory, EEPROM, and programmable peripherals. PIC18F-series MCUs sit in Microchip's mainstream 8-bit tier, above baseline PIC16 devices but below dsPIC and 32-bit families, and are widely used for cost-sensitive embedded control with USB connectivity requirements. Key features of the PIC18F25K50 include a built-in USB 2.0 Full-Speed transceiver with on-chip pull-up resistors (no external crystal required for low-speed USB), 25 programmable I/O pins, 2 KB of SRAM, 256 bytes of EEPROM, two 8-bit timers, three CCP/ECCP modules, two MSSP (SPI/I2C) peripherals, two EUSART modules, a 10-bit ADC with 14 channels, and nanoWatt XLP extreme-low-power technology that drops current consumption into the nanoampere range during sleep. The ICSP (In-Circuit Serial Programming) interface allows in-target firmware updates via two I/O pins. The device operates from 2.3 V to 5.5 V supply, supporting battery-powered and USB bus-powered designs. Its integrated USB eliminates the external USB-to-UART bridge typically required on 8-bit MCUs, reducing BOM cost and PCB area in USB peripherals such as HID input devices, CDC virtual COM ports, and human-interface adapters. Typical applications include USB HID peripherals (keyboards, mice, game controllers), USB-to-serial adapters, USB sensor interfaces, low-power IoT sensor nodes, industrial control with USB diagnostics, and battery-powered data-logging accessories. The 'T' tape-and-reel suffix indicates this specific variant is intended for high-volume SMT production lines. When designing with this part, ensure the VUSB pin has a 220 nF decoupling capacitor to ground and a 1 uF bulk cap on VDD. Configure the internal 48 MHz PLL correctly for USB operation, and confirm that the chosen clock mode (INTIO vs. HS crystal) matches USB full-speed timing requirements per the datasheet's oscillator configuration table. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement the manufacturer datasheet, giving engineers a single-source view for sourcing, replacement, and application guidance.

Permintaan RFG Kontak

PIC18F25K50T-I/SS

PIC18F25K50T-I/SS - 8-Bit 48MHz 32KB Flash USB MCU | Microchip

The Microchip Technology PIC18F25K50T-I/SS is an 8-bit PIC18 microcontroller IC from the PIC XLP 18K family, delivering 48 MHz CPU performance with 32 KB (16K x 16) of Flash program memory and an integrated USB 2.0 full-speed transceiver. The device is housed in a 28-pin SSOP package and supports 22 digital I/O pins, 256 bytes of EEPROM, and 2 KB of SRAM, making it suitable for compact USB-enabled embedded designs. It operates from 2.3 V to 5.5 V across the industrial -40C to +85C range. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating CPU core, non-volatile program memory (Flash), volatile data memory (RAM), EEPROM, and a rich set of peripherals such as timers, ADC, communication interfaces, and I/O. The PIC18F25K50 belongs to the eXtreme Low Power (XLP) family, sitting in the power-management IC -> microcontroller -> 8-bit MCU -> PIC18 product-type hierarchy. Its nanoWatt XLP technology minimizes active and sleep currents, enabling battery-friendly USB peripherals. Key differentiating features include the on-chip USB 2.0 full-speed transceiver with internal 48 MHz oscillator that achieves USB-accurate timing via Active Clock Tuning from the USB host, eliminating the need for an external crystal in many USB applications. The device provides 32 KB self-read/write Flash, 2 KB RAM, 256 B EEPROM, 22 I/O, multiple communication peripherals (I2C/SPI/EUSART), and 10-bit ADC capability with multiple Capture/Compare/PWM modules for motor and LED control. The XLP sleep currents extend battery life in always-on sensors and wearables. Architecturally, the PIC18F25K50 uses an enhanced Harvard RISC core with 200 ns instruction cycle, hardware 8x8 multiplier, and a 16-level hardware stack. The integrated USB module, on-chip voltage regulator for bus-powered designs, and Active Clock Tuning form a tightly engineered USB subsystem. Compared to older PIC18F2550 designs, the K50 reduces external BOM by integrating the USB transceiver and trimming crystal needs. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), USB-to-UART bridges, USB sensor and data-acquisition nodes, low-power IoT endpoints, industrial control interfaces with USB diagnostics, and consumer electronics requiring a small-footprint USB device controller. The wide 2.3-5.5 V range also suits battery-powered designs using 2x AA cells or Li-ion. When designing with this MCU, place the VUSB decoupling capacitor (typically 470 nF) close to the VUSB pin, respect USB DP/DM trace impedance (90 ohms differential), and use the internal regulator or external 3.3 V LDO for bus-powered designs. The Microchip MPLAB X IDE and XC8 compiler fully support the PIC18F25K50 family, simplifying firmware development. This page synthesizes verified distributor pricing, drop-in alternatives from the same Microchip K50 family, and practical USB design notes not collected in any single manufacturer document.

Permintaan RFG Kontak

PIC18F25K80-E/MM

PIC18F25K80-E/MM - 8-bit 64MHz 32KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18F25K80-E/MM is a high-performance 8-bit RISC flash microcontroller featuring an integrated ECAN (Enhanced CAN) controller and eXtreme Low Power (XLP) nanoWatt technology, housed in a 28-pin QFN-S (6x6 mm) package with exposed pad. The device delivers 64 MHz (16 MIPS) performance from a 32 KB (16K x 16) flash program memory array, paired with 3.6 KB RAM and 1 KB EEPROM, and operates from 1.8 V to 5.5 V across the full automotive/industrial temperature range of -40C to +125C. On-chip peripherals include a 12-bit A/D converter (with up to 8 channels), multiple timers, Enhanced USART, SPI, I2C, and the ECAN module that makes this part the canonical Microchip choice for in-vehicle networking nodes. An 8-bit PIC microcontroller is a compact, low-cost CMOS compute core that executes a reduced-instruction-set instruction set (RISC) in a single clock cycle, providing deterministic timing for embedded control. Within the broader taxonomy, the PIC18F25K80 belongs to the PIC18 family of mid-range 8-bit microcontrollers, sits in the MCU / microcontroller product category (a subset of embedded microcontrollers and integrated circuits), and is positioned as a power-optimized, connectivity-rich variant aimed at CAN-bus and battery-powered applications. Key features include nanoWatt XLP sleep currents as low as 100 nA typical (deep sleep), an integrated CTMU (Charge Time Measurement Unit) for capacitive touch or precise time-of-flight measurements, an on-chip 8 MHz internal oscillator selectable via configuration bits, and dual-watchdog with Windowed WDT. The ECAN module is compliant with CAN 2.0B active, supporting 11-bit and 29-bit identifiers, which removes the need for an external CAN transceiver microcontroller pair. Architecturally, the device uses a 16-bit wide instruction path with an 8-bit data path, eight-level hardware stack, hardware multiplier (8x8 single-cycle), and 31 interrupt sources with vectored interrupt controller. The 12-bit ADC with acquisition timer supports up to 100 ksps conversion, sufficient for sensor readout in industrial control loops. Typical applications include automotive body control modules (BCM), HVAC controllers, CAN node endpoints in vehicle networks, industrial elevator control panels, building automation sensor hubs, capacitive touch user interfaces via CTMU, and battery-powered metering nodes. The wide 1.8V-5.5V supply range supports direct Li-Ion battery connection without a separate LDO. When designing with this part, place a 100 nF decoupling capacitor on every VDD/VSS pair and ensure the exposed pad (EP) is soldered to a continuous ground plane. The E suffix denotes the extended (-40C to +125C) temperature grade suitable for under-hood automotive and outdoor industrial enclosures. This page synthesizes distributor pricing, drop-in QFN-28 alternatives from the same PIC18F family, ECAN node firmware design notes, and CTMU touch measurement guidance not consolidated on any single distributor or manufacturer page.

Permintaan RFG Kontak

PIC18F25K80-E/SP

PIC18F25K80-E/SP - 32KB Flash 8-bit MCU w/ ECAN | Microchip

The Microchip Technology PIC18F25K80-E/SP is a high-performance 8-bit PIC microcontroller with 32KB Flash, 4KB RAM, integrated ECAN, and nanoWatt XLP extreme low-power technology, housed in a 28-pin SPDIP (0.3in) through-hole package. It operates from 1.8V to 5.5V at up to 64MHz (16 MIPS) and integrates a 12-bit ADC, CTMU, and automotive-grade peripherals. The -E suffix denotes the extended (-40C to +125C) industrial temperature grade, making the part suitable for harsh-environment applications. The PIC18F66K80 family includes variants from 28 to 64 pins, allowing scalable designs without firmware changes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral set on one die. PIC18F-series MCUs use a modified Harvard 8-bit architecture with 16-bit instructions, placing them in the 8-bit microcontroller category above baseline PIC10/12/16 devices. Within the broader taxonomy, PIC18F belongs to: PIC18F -> PIC18 family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The K80 sub-family specifically adds ECAN and nanoWatt XLP for low-power networked nodes. Key features of the PIC18F25K80 include 32KB self-programmable Flash with 1KB EEPROM, 4KB SRAM, 64MHz CPU (16 MIPS throughput), an integrated CAN 2.0B controller (ECAN), three ECCP+ECCP modules, two MSSP (SPI/I2C), two enhanced USART, 11 channels of 12-bit ADC with auto-acquisition, CTMU for capacitive touch or current measurement, nanoWatt XLP sleep currents as low as 20 nA, and a wide 1.8V-5.5V operating range. The 28-pin SPDIP package simplifies breadboard prototyping and field-replaceable designs. Architecturally, the PIC18F25K80 uses Microchip's enhanced Harvard bus with separate instruction and data paths, a 32-level hardware stack, and a priority interrupt controller. The CTMU (Charge Time Measurement Unit) provides timing for mTouch capacitive touch sensing or precise current measurement, while the ECAN peripheral implements CAN 2.0B active/passive with filtering and acceptance masks. nanoWalt XLP technology combined with multiple idle/sleep modes (Doze, Sleep, Deep Sleep, RTCC) enables coin-cell or energy-harvesting battery life. Typical applications include CAN-based automotive body and comfort modules, building automation (elevator/HVAC control), industrial sensor nodes, capacitive touch human-machine interfaces, and low-power remote monitoring. The wide operating voltage and ECAN peripheral also suit it for battery-powered CAN nodes in vehicle body electronics and CAN-connected industrial sensors. When designing with the PIC18F25K80-E/SP, plan for the 28-pin SPDIP footprint (0.3in row spacing) and ensure decoupling: 100nF on VDD/VSS pairs, plus 10uF bulk near the IC. Configure the ICSP/ICD pins (PGC/PGD) for in-circuit programming and debugging using tools such as MPLAB X IDE with PICkit 3/4 or ICD 3/4. For long-term reliability, route CANH/CANL as a differential pair with 120-ohm termination at each end of the bus. This page consolidates verified distributor pricing, drop-in same-brand and cross-brand alternatives in the SPDIP-28 footprint, comparison data, and practical design notes not found on Mouser or DigiKey product summaries.

Permintaan RFG Kontak

PIC18F25K80-E/SS

PIC18F25K80-E/SS - 8-bit MCU, 32KB Flash, ECAN, XLP | Microchip

The Microchip Technology PIC18F25K80-E/SS is a high-performance 8-bit PIC18 microcontroller featuring integrated ECAN (Enhanced Controller Area Network), 32KB of Flash program memory, 3.6KB of RAM, and eXtreme Low Power (XLP) technology. Housed in a 28-pin SSOP package, the device operates from 1.8V to 5.5V and runs at up to 64MHz (16 MIPS), making it suitable for automotive, industrial, and consumer applications where CAN connectivity and low power consumption are critical design requirements. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable I/O peripherals. The PIC18F family uses Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, optimized for deterministic real-time control. The PIC18F25K80 sits within the K80 sub-family that adds integrated ECAN 2.0B, CTMU (Charge Time Measurement Unit) for capacitive touch, and nanoWatt XLP sleep modes below 100 nA — extending battery life across industrial sensor nodes and automotive body modules. Key features include 32KB (16K x 16) of self-programmable Flash, 1KB of EEPROM, a 12-bit ADC with up to 11 channels, an 8-bit DAC, three analog comparators, four 16-bit timers, two MSSP (SPI/I2C) modules, two enhanced USART, and 24 digital I/O pins. The integrated ECAN module supports CAN 2.0B active with bus speeds up to 1 Mbps. The CTMU provides on-chip waveform generation for capacitive touch sensing without external components. The device leverages an enhanced PIC18 CPU core with hardware multiply and a 32-level hardware stack, paired with a 4-deep prefetch buffer to sustain 16 MIPS throughput at 64MHz. The 12-bit ADC achieves up to 100 ksps with acquisition time configurable in software, while the ECAN engine handles filtering and masking in hardware, offloading message acceptance from the CPU. Typical applications include automotive body and chassis ECAN nodes (body control modules, instrument clusters, mirror controllers), industrial CAN-bus sensor and actuator networks, building automation (HVAC, elevator controllers), and low-power battery-backed IoT edge devices. The wide 1.8V–5.5V supply range supports both 3.3V and 5V system designs. When designing with this MCU, ensure the ECAN transceiver supply and reference voltages are stable before enabling the CAN module. Use MPLAB X IDE with XC8 compiler and configure the CTMU current source via the dedicated register set for repeatable touch measurements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak

PIC18F25K80-H/SS

PIC18F25K80-H/SS - 8-bit MCU, 32KB Flash, ECAN, 64MHz | Microchip

The Microchip Technology PIC18F25K80-H/SS is a high-performance 8-bit PIC microcontroller with integrated ECAN, 32 KB (16K x 16) Flash program memory, 3.6 KB RAM, 64 MHz CPU clock and 16 MIPS throughput, packaged in a 28-pin SSOP for high-temperature applications. Operating from 1.8 V to 5.5 V, it delivers 16 MIPS at 5 V and 8 MIPS at 3.3 V, supports up to 24 general-purpose I/O pins, and integrates a 12-bit ADC, multiple timers, ECAN, SPI, I2C, UART, and CTMU peripheral set. The PIC18F25K80-H/SS is part of the high-temperature ("H") variant of the PIC18F66K80 family, targeting automotive and industrial environments with extended thermal reliability. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals on one die. PIC microcontrollers use a modified Harvard RISC architecture with a 16-bit instruction word optimized for deterministic, low-power embedded control. The PIC18F family sits at the upper end of Microchip's 8-bit portfolio, offering higher memory density and richer peripherals (ECAN, 12-bit ADC) than PIC16F parts while maintaining the classic PIC ease of use and the eXtreme Low Power (XLP) nanoWatt technology. Key features of the PIC18F25K80-H/SS include 32 KB Flash, 3.6 KB RAM, 1 KB EEPROM, integrated ECAN module for industrial and automotive networking, a 12-bit A/D converter with up to 24 channels, three 16-bit timers, capture/compare/PWM peripherals, two MSSP ports for SPI/I2C, two enhanced USART modules, CTMU for capacitive touch or accurate time measurement, and nanoWatt XLP sleep modes. The high-temperature ("-H") silicon supports operation across an extended industrial thermal range, suitable for under-hood automotive, elevator controls, and building automation. The device uses a 5-stage pipelined RISC core with hardware multiply and divide, and an internal PLL allows 64 MHz operation from a low-frequency external crystal. XLP technology provides sub-microamp sleep currents and fast wake-up times for battery-backed designs. The ECAN peripheral conforms to CAN 2.0B active specification with 8 buffers and 16 acceptance filters, enabling multi-node industrial networking on a single MCU. Typical applications include automotive body and powertrain ECUs (non-safety-critical), building and elevator control, industrial CAN nodes (sensors, motor drives, lighting controllers), battery-powered telemetry, and capacitive-touch user interfaces using CTMU. The 28-pin SSOP footprint and 0.65 mm pitch allow compact layouts while remaining hand-solderable, and the wide 1.8-5.5 V range supports direct Li-ion or 3.3 V system buses. Design consideration: when migrating from the industrial-temperature PIC18F25K80-I/SS, verify that software timing assumptions are compatible with the wider temperature behavior of the H variant. For mixed-voltage systems, decouple VDD/VSS pairs adjacent to the MCU with 100 nF + 10 uF ceramic capacitors placed within 5 mm of each pin. This page synthesizes distributor pricing, drop-in same-package alternatives across the PIC18F K80 family, parametric comparison tables, and practical design notes not found in the manufacturer datasheet alone, providing information gain over standard catalog listings.

Permintaan RFG Kontak

PIC18F25K80-I/MM

PIC18F25K80-I/MM - 8-bit 64MHz MCU, 32KB Flash, ECAN | Microchip

The Microchip Technology PIC18F25K80-I/MM is an 8-bit PIC18 enhanced flash microcontroller running up to 64 MHz (16 MIPS) with 32 KB of Flash program memory, 3.6 KB of SRAM, and 1 KB of EEPROM, integrated with ECAN, nanoWatt XLP extreme low-power technology, and a 12-bit ADC, all housed in a 28-pin QFN-S (6x6 mm) package marked /MM. Integrated peripherals include ECAN, two EUSART, SPI/I2C, a 12-bit 11-channel ADC, four timers with CCP/ECCP, CTMU, and a brown-out reset, supporting demanding control and connectivity designs. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and peripherals such as timers, ADCs, and communication interfaces; in the wider taxonomy, the PIC18F25K80 belongs to PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. ECAN is Microchip's enhanced implementation of the Controller Area Network (CAN) protocol originally standardized as ISO 11898 and widely used in automotive and industrial networks, and nanoWatt XLP is Microchip's low-power technology that drops sleep current to nanoamp levels for battery-backed designs. Key features include operation from 1.8 V to 5.5 V, sleep current below 60 nA typical, integrated ECAN for CAN 2.0B networks, a 12-bit A/D converter with up to 11 analog input channels plus CTMU for capacitive touch, and four 16-bit timers including CCP/ECCP. The 64 MHz clock supports 16 MIPS throughput, executing 1 instruction per clock thanks to the PIC18 RISC-style pipeline, while on-board debugging is provided through in-circuit debug and two programming pins for In-Circuit Serial Programming (ICSP). Typical applications include building automation nodes, elevator control panels, industrial CAN nodes, automotive body and sensor networks, and battery-powered remote sensor modules. The wide 1.8V-5.5V supply range lets the part operate directly from a single Li-ion or 2xAA cell stack, while ECAN enables robust peer-to-peer communication in noisy industrial or vehicle environments. Use a 100 nF decoupling capacitor close to VDD plus a 10 uF bulk capacitor when load steps are large; bypass AVSS/AVDD separately on ADC references and respect the analog and digital ground split. Configure the device for ECAN via the CONFIG register bits and verify the bit timing against the oscillator choice. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet — providing engineering decision context beyond the spec sheet.

Permintaan RFG Kontak

PIC18F25K80-I/SO

PIC18F25K80-I/SO - 8-Bit MCU, 32KB Flash, ECAN, 28-SOIC | Microchip

The Microchip Technology PIC18F25K80-I/SO is a high-performance 8-bit PIC18 microcontroller with integrated ECAN, 32KB of Flash program memory, 4KB of RAM, and a 64 MHz maximum CPU clock (16 MIPS throughput), packaged in a 28-pin SOIC. It features a 12-bit ADC with up to 11 channels, an ECAN module for automotive-grade CAN networking, nanoWatt XLP extreme low-power technology, and an integrated Charge Time Measurement Unit (CTMU) for capacitive touch and precise timing. An 8-bit microcontroller (MCU) is a self-contained computer-on-a-chip that integrates a CPU, memory (Flash/RAM/EEPROM), peripherals (ADC, timers, communication blocks), and I/O on a single die. Within the broader taxonomy, an 8-bit MCU sits under microcontroller -> embedded processor -> semiconductor device. The PIC18 family is Microchip's enhanced 8-bit architecture, designed for higher performance and C-compilable code compared to baseline PIC16 parts, while remaining easier than migrating to 16-bit PIC24 or dsPIC parts. Key features of the PIC18F25K80 include nanoWatt XLP sleep currents as low as sub-1 µA typical, an integrated ECAN controller supporting CAN 2.0B active, 1.8V to 5.5V operation suitable for both 3.3V and 5V designs, an 8x8 hardware multiplier for efficient math, and on-chip EEPROM for non-volatile data storage. The 12-bit ADC provides up to 100 ksps conversion rate with internal reference options. From an architectural perspective, the PIC18F25K80 uses an enhanced Harvard RISC core with a modified instruction set that supports both 8-bit and 16-bit operations, a 31-level hardware stack, and direct, indirect, and relative addressing modes. Peripherals are mapped to SFR space and accessed through well-documented header files in MPLAB X IDE, with peripheral pin select and PPS not present on this generation (those were introduced in newer PIC18F-K42/K40 families). Typical applications include automotive body and chassis ECAN nodes, industrial building control (HVAC, lighting, elevator control), sensor interfaces with capacitive touch buttons, low-power battery-powered remote nodes, and CAN-based sensor networks. The combination of ECAN and XLP makes it especially attractive in distributed automotive/industrial systems where wake-on-CAN and standby current budgets are critical. When designing with this device, note that the ECAN pins are multiplexed with general-purpose I/O; designers must configure PPS (where applicable) and verify pin remapping for their CAN bus topology. Use the CTMU for low-cost capacitive touch, and budget PCB layout for the CAN transceiver's EMC requirements (common-mode choke, split termination). This page synthesizes distributor pricing, drop-in alternatives, application guidance and design notes not found in the manufacturer datasheet alone - intended for engineers selecting a pin-compatible MCU for new designs and field replacement.

Permintaan RFG Kontak

PIC18F25K80-I/SS

PIC18F25K80-I/SS - 8-bit 64MHz 32KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18F25K80-I/SS is an 8-bit PIC18 enhanced flash microcontroller with integrated ECAN, 32 KB of program flash, 4 KB of RAM, and 1 KB of EEPROM, operating up to 64 MHz (16 MIPS) from a 1.8 V to 5.5 V supply, housed in a 28-pin SSOP (5.30 mm body) package. The part integrates nanoWatt XLP extreme-low-power technology for sleep currents suitable for always-on building-control and battery-backed designs. According to the Microchip product page, it is targeted at automotive, building control, elevator control, and industrial applications where on-board CAN networking is required. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O on one die. PIC18F-series devices use an enhanced Harvard 8-bit RISC core with hardware multiply, paired with nanoWatt XLP sleep modes to push standby current into the nanoampere range. The PIC18F25K80 family specifically integrates a CAN 2.0B controller (ECAN) for industrial and automotive networking without an external transceiver controller. Key features include a 12-bit ADC with up to 11 channels, a CTMU (Charge Time Measurement Unit) for capacitive touch and time-of-flight measurement, multiple Enhanced Compare/PWM modules for precision motor control, and a 16-bit timer/counter. Per the manufacturer datasheet, the device also includes an LCD driver and supports 1.8V to 5.5V operation with low sleep current, enabling battery-backed designs. Architecturally, the PIC18F25K80 uses the enhanced PIC18 core with 8-bit data path, 16-bit instructions, hardware multiply, and a 31-level hardware stack. The ECAN module implements CAN 2.0B active/passive with hardware filtering and acceptance masks, offloading message filtering from the CPU for deterministic real-time bus performance. Typical applications include industrial building automation with CAN nodes, automotive body and HVAC controllers, elevator control panels, and low-power sensor nodes with on-board ADC measurement. The combination of ECAN, XLP sleep modes, and a 12-bit ADC with CTMU makes this part a strong fit for distributed sensor networks where power budget is constrained but deterministic bus communication is required. When designing with this part, plan I/O carefully: the 28-pin SSOP exposes a subset of the 64-pin die's peripherals. Pins used for analog inputs cannot double as digital outputs, and the ECAN TX/RX pins are dedicated. The PIC18F25K80 requires a single 3.3V or 5V rail; the internal voltage regulator provides the core 1.8V supply. This page synthesizes distributor pricing, drop-in alternatives, and design notes for the PIC18F25K80-I/SS that go beyond the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25K80T-I/SO

PIC18F25K80T-I/SO - 32KB Flash 8-bit MCU w/ ECAN | Microchip

The Microchip Technology PIC18F25K80T-I/SO is an 8-bit enhanced flash microcontroller with integrated ECAN, 32KB of program flash memory, 4KB of RAM, and 1KB of EEPROM, operating at up to 64 MHz (16 MIPS) in a 28-pin SOIC package. It belongs to the PIC18F K80 family, which combines nanoWatt XLP extreme low-power technology with an on-chip CAN 2.0B peripheral, addressing automotive body, building-control and industrial sensor-node applications. An 8-bit MCU (microcontroller) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals, and I/O. PIC18F devices use a modified Harvard architecture with a RISC instruction set optimized for deterministic real-time control, and the K-series adds wide-operating-voltage (1.8 V-5.5 V) and ultra-low-power sleep modes targeting battery-backed and energy-harvesting designs. Key features include 12-bit ADC with up to 11 channels, 2 CCP/ECCP modules, 2 MSSP (SPI/I2C), 2 enhanced USART, an enhanced CAN module, CTMU for capacitive touch or precise time measurement, 4 timers and a 16-bit CRC peripheral. The 28-SOIC (SO) industrial-temperature (-40C to +85C) variant supports surface-mount assembly in space-constrained boards where an SOIC-28 footprint is already laid out. The PIC18F25K80T-I/SO uses a high-performance RISC core with hardware multiply, a 16-bit instruction word and a 31-level hardware stack. nanoWatt XLP technology delivers sub-uA sleep currents, while the integrated ECAN peripheral implements CAN 2.0B active/passive with bus health diagnostics, eliminating the need for an external CAN controller. The 12-bit ADC reaches up to 100 ksps with acquisition control. Typical applications include automotive body and comfort modules, building-control sensor nodes, industrial CAN-bus slaves, elevator-control boards, capacitive-touch user interfaces, and battery-powered metering. The wide VDD range and ECAN make it a strong fit where a single MCU has to talk both to analog sensors and to a robust vehicle or industrial backbone. When designing with this part, leave room for the ECAN transceiver footprint and bus termination; verify that your compiler toolchain (MPLAB X with XC8) supports the silicon revision on the device marking and budget for the ICD debugger header. The CTMU needs a calibrated current source for touch measurements and adequate ADC settling time for accurate temperature or ratiometric sensing. This page synthesizes distributor pricing, same-brand drop-in alternatives and practical design notes that complement the Microchip datasheet.

Permintaan RFG Kontak

PIC18F25K80T-I/SS

PIC18F25K80T-I/SS - 32KB Flash 8-bit MCU w/ECAN, XLP | Microchip

The Microchip Technology PIC18F25K80T-I/SS is a high-performance 8-bit RISC microcontroller with integrated ECAN, 32 KB of Flash program memory, 3.6 KB of RAM, and 1 KB of EEPROM, housed in a 28-pin SSOP (5.30 mm body) package supplied on Tape & Reel. It runs at up to 64 MHz (16 MIPS) across a 1.8 V to 5.5 V operating range, integrates a 12-bit ADC with up to 11 channels, and adds nanoWatt XLP extreme-low-power technology for sleep currents in the nanoampere range. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data-path CPU, on-chip program memory (Flash/ROM), data memory (RAM/EEPROM), and a rich set of peripherals. Within the MCU hierarchy, the PIC18 family is Microchip's high-performance 8-bit tier, sitting above the PIC16 baseline tier. ECAN-enabled PIC18 K80 devices add a CAN 2.0B controller, making them particularly suitable for industrial, building-automation, elevator-control, and automotive body networks where deterministic on-board communication is required. Key features include seven CCP/ECCP modules for precision PWM, two MSSP ports that can be configured for SPI or I2C, up to 24 general-purpose I/O pins, multiple timer modules, a CTMU (Charge Time Measurement Unit) for capacitive touch and precise time-of-flight measurement, and hardware LIN support. The combination of nanoWatt XLP, wide 1.8 V–5.5 V supply, and -40 °C to +85 °C industrial temperature range makes it tolerant of battery, USB-powered, and automotive battery environments. The CPU is a Harvard-architecture PIC18 core with hardware multiply, a 31-level stack, and 16-bit instructions, delivering 16 MIPS at 64 MHz. The 12-bit ADC supports up to 11 input channels with acquisition-time control, while the ECAN module is compliant with CAN 2.0B active with both standard and extended identifiers, plus DeviceNet and CAN-FD-ready filtering. On-chip debug is supported via ICD/ICSP, allowing the same part to be used through prototype and production. Typical applications include CAN nodes for industrial elevator and HVAC controllers, automotive body and lighting modules, building-automation sensor hubs, capacitive-touch user interfaces using the CTMU, battery-powered metering nodes that benefit from XLP sleep current, and USB-to-CAN bridges. Pairing the device with an external CAN transceiver such as the MCP2551 or MCP2561 completes a robust 1 Mbps CAN node. When designing with the PIC18F25K80T-I/SS, allocate at least four I/O lines for ICSP/ICD programming and debug, place a 0.1 µF ceramic bypass capacitor within 5 mm of VDD, and observe the datasheet's VDD/VSS pinout for the SSOP-28 package. The '-T' suffix indicates Tape & Reel packaging; the industrial '-I' grade supports -40 °C to +85 °C operation. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the standalone datasheet, helping procurement and firmware engineers select and qualify the right variant faster.

Permintaan RFG Kontak

Subkategori

Produk (39.000+)

PIC18F25K42-E/SP - 32KB Flash 8-bit MCU | 28-SPDIP | Microchip

PIC18F25K42-E/SS - 8-Bit 64MHz 32KB Flash MCU | Microchip

PIC18F25K42-I/MV - 8-Bit 64MHz XLP MCU 32KB Flash UQFN-28 | Microchip

PIC18F25K42-I/SO - 8-bit 64MHz 32KB Flash XLP MCU | Microchip

PIC18F25K42-I/SP - 32KB Flash 8-bit MCU 64MHz 28-SPDIP | Microchip

PIC18F25K42-I/SS - 8-bit 64MHz 32KB Flash MCU 28-SSOP | Microchip

PIC18F25K42T-E/SSVAO - 32KB Flash 8-bit MCU, AEC-Q100 | Microchip

PIC18F25K42T-I/ML - 32KB Flash 8-bit MCU 28-QFN | Microchip

PIC18F25K42T-I/MV - 8-bit MCU, 32KB Flash, 64MHz, 28-UQFN | Microchip

PIC18F25K50-E/SP - 8-bit USB MCU, 32KB Flash, 48MHz | Microchip

PIC18F25K50-I/ML - 8-Bit USB MCU, 32KB Flash, 28-QFN | Microchip

PIC18F25K50-I/SO - 32KB Flash USB MCU 48MHz 28-SOIC | Microchip

PIC18F25K50T-I/ML - 32KB Flash USB MCU 28-QFN | Microchip

PIC18F25K50T-I/SO - 32KB Flash USB 8-bit MCU 48MHz SOIC-28 | Microchip

PIC18F25K50T-I/SS - 8-Bit 48MHz 32KB Flash USB MCU | Microchip

PIC18F25K80-E/MM - 8-bit 64MHz 32KB Flash MCU w/ ECAN | Microchip

PIC18F25K80-E/SP - 32KB Flash 8-bit MCU w/ ECAN | Microchip

PIC18F25K80-E/SS - 8-bit MCU, 32KB Flash, ECAN, XLP | Microchip

PIC18F25K80-H/SS - 8-bit MCU, 32KB Flash, ECAN, 64MHz | Microchip

PIC18F25K80-I/MM - 8-bit 64MHz MCU, 32KB Flash, ECAN | Microchip

PIC18F25K80-I/SO - 8-Bit MCU, 32KB Flash, ECAN, 28-SOIC | Microchip

PIC18F25K80-I/SS - 8-bit 64MHz 32KB Flash MCU w/ ECAN | Microchip

PIC18F25K80T-I/SO - 32KB Flash 8-bit MCU w/ ECAN | Microchip

PIC18F25K80T-I/SS - 32KB Flash 8-bit MCU w/ECAN, XLP | Microchip