Sirkuit Terpadu

PIC18F25K83-E/SO

PIC18F25K83-E/SO - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18F25K83-E/SO is an 8-bit PIC microcontroller from the PIC18(L)F25/26K83 family featuring CAN technology, a 12-bit ADC with Computation (ADC2), and 32KB of Flash program memory. The device runs at up to 64MHz and is housed in a 28-pin SOIC wide-body package. The "-E" temperature grade denotes an extended automotive temperature range of -40C to +125C, and the "/SO" suffix identifies the 28-SOIC (SOIC-28 wide, 7.50mm body width) package. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), data memory (RAM), and a rich set of peripheral interfaces (ADC, timers, communication ports, GPIO). The PIC18 family is built on an enhanced Harvard RISC architecture with a modified 16-bit instruction word; the "18K" designation refers to the K83 sub-family that integrates CAN, ADC2 (computation engine with averaging, oversampling, and CVD capacitive touch), and Microchip's eXtreme Low Power (XLP) technology. The PIC18F25K83 sits within the broader taxonomy: MCU -> 8-bit MCU -> PIC microcontroller -> PIC18 family -> PIC18F2xK83 sub-family. Key features include 32KB (16K x 16) Flash, 2KB RAM, 1KB EEPROM, a 12-bit differential ADC2 with up to 100 channels of capacitive touch sensing via CVD, a CAN 2.0B controller, multiple UART/SPI/I2C peripherals, a 16-bit CRC/Scan module for functional safety, and XLP nanoWatt sleep currents below 50 nA. The 64MHz internal oscillator and 4x PLL deliver 16 MIPS of CPU throughput. The 12-bit ADC2 is the headline differentiator: it performs automatic Capacitive Voltage Divider scans for mTouch touch buttons, sliders, and proximity sensors without CPU intervention, and supports hardware oversampling/averaging for higher effective resolution. Combined with the 16-bit CRC peripheral and memory BIST support, the K83 series is qualified for IEC 61508 / ISO 26262 functional-safety applications. Typical applications include automotive body and HVAC controllers, CAN node peripherals, capacitive touch user interfaces, industrial sensor transmitters, low-power IoT edge nodes, and functional-safety subsystems. The wide temperature grade makes it suitable for under-hood and chassis modules. When designing with this device, allocate one of the 28 SOIC pins for MCLR (reset), ensure adequate decoupling on VDD/AVDD/VBAT, and consult the ADC2 CVD tuning guide for noise-free capacitive touch channels. The "E" temperature grade requires derating for thermal resistance of the 28-SOIC at 1oz 4-layer PCB copper. This page synthesizes distributor pricing, parametric comparison data, and practical design notes that extend beyond the manufacturer datasheet table of contents to help engineers make sourcing and design decisions.

Permintaan RFG Kontak

PIC18F25K83-E/SP

PIC18F25K83-E/SP - 8-bit 64MHz 32KB Flash MCU w/ CAN | Microchip

The Microchip PIC18F25K83-E/SP is an 8-bit PIC18 microcontroller with XLP low-power technology and Functional Safety (FuSa) support, offering 64 MHz CPU performance, 32 KB Flash, 2 KB RAM, and integrated CAN bus technology in a 28-pin SPDIP through-hole package. It belongs to the PIC18(L)F25/26K83 family of 28-pin low-power, high-performance MCUs. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, designed for embedded control tasks such as sensor reading, motor driving, and protocol bridging. Microcontrollers sit within the broader hierarchy of microprocessors -> computing ICs -> integrated circuits -> semiconductors, and the PIC18 family is Microchip's mainstream high-performance 8-bit line, upgraded from the baseline PIC16 architecture with a 16-bit instruction word and linear memory addressing. Key features of this device include a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) techniques for advanced touch sensing, averaging, filtering, and oversampling; a CAN 2.0B module for vehicle or industrial networking; multiple Core Independent Peripherals (CIPs) that offload tasks from the CPU; and XLP technology for sleep currents in the nanoamp range. The 28-SPDIP package is the most repair-friendly through-hole option for prototype and industrial designs. The architecture pairs a 16-bit instruction word with an 8-bit data path, supporting up to 64 MHz operation from an internal oscillator, plus a hardware multiplier and C-optimized compiler support via MPLAB XC8. CIPs include Complementary Waveform Generator (CWG), Configurable Logic Cell (CLC), and multiple PWM/SCCP/MCCP modules. Together these allow the MCU to handle capacitive touch, motor control, and CAN communication largely without CPU intervention. Typical applications include CAN-connected automotive body controllers, industrial sensor nodes, capacitive-touch user interfaces, low-power battery monitors, and small motor-control subsystems where 32 KB Flash and 2 KB RAM are sufficient. The Extended (-E) temperature grade supports -40 C to +125 C operation for harsh environments. When designing with this part, route the CAN bus with a 120-ohm twisted pair and use an external CAN transceiver such as the MCP2562; do not rely on the internal CAN module to drive the bus directly. For capacitive touch, follow the CVD layout guidelines in the datasheet and dedicate a ground ring around each electrode for noise immunity. This page synthesizes verified distributor pricing, drop-in compatible alternatives from the same PIC18 K-series family, and practical design notes beyond the manufacturer datasheet to support both new design and second-source qualification.

Permintaan RFG Kontak

PIC18F25K83-E/SS

PIC18F25K83-E/SS - 64MHz 8-bit MCU, 32KB Flash, CAN, 28-SSOP | Microchip

The Microchip Technology PIC18F25K83-E/SS is a 64 MHz 8-bit PIC18 microcontroller with 32 KB Flash, 2 KB RAM, and 1 KB EEPROM in a 28-pin SSOP package, integrating CAN technology and a 12-bit ADC with Computation (ADC²) for advanced touch sensing. The '-E' suffix denotes the extended industrial temperature grade of -40 °C to +125 °C, while the '/SS' suffix designates the 28-pin SSOP package, and the part belongs to the PIC18F25K83 sub-family alongside the PIC18F26K83, PIC18F45K83, and PIC18F46K83 variants. A PIC18F-series 8-bit MCU is a CISC/RISC hybrid microcontroller built around the PIC Harvard architecture, enhanced instruction set, and Core Independent Peripherals (CIPs). It sits in the hierarchy: PIC18F -> 8-bit PIC MCU -> PIC microcontroller -> microcontroller -> embedded computing. The K83 generation specifically adds an integrated CAN module (CAN FD capable), a 12-bit differential ADC² with Capacitive Voltage Divider (CVD) hardware, and vectored interrupt controller with fixed latency for deterministic real-time response. Key features include a maximum CPU clock of 64 MHz (16 MIPS), 25 general-purpose I/O pins, an 8-channel 12-bit ADC² with hardware oversampling and CVD for capacitive touch, one CAN FD module, one I²C, two SPI/I²S, two UART modules, a 5-bit DAC, and four 16-bit timers. Power-saving features include nanoWatt XLP technology with typical idle current under 1 µA, sleep current under 100 nA, and an operating voltage range of 2.3 V to 5.5 V supporting both 3.3 V and 5 V rails. The PIC18F25K83 family combines Core Independent Peripherals with a CAN bus interface, allowing offloading of touch sensing, signal conditioning, and communication tasks from the CPU. Hardware CVD automates capacitive touch measurements, the DMA-capable ADC² performs averaging and thresholding autonomously, and CIPs such as the CWG, NCO, and PWM modules allow motor control and waveform generation without CPU intervention, making the K83 well suited for real-time industrial and automotive body-control designs. Typical applications include capacitive touch human-machine interfaces, CAN node industrial controllers, automotive body and lighting modules, sensor hub platforms, low-power IoT edge nodes, and small motor or fan control subsystems. Designers should pick this part when they need CAN connectivity plus integrated touch in a compact SSOP footprint. A key design consideration is decoupling: place 100 nF and 1 µF ceramic capacitors as close as possible to VDD/AVDD pins, route the 32.768 kHz crystal traces short and guarded, and keep the CAN bus 120 Ω termination accurate to maintain signal integrity on industrial networks. The 28-SSOP package also requires thermal relief on the PCB pad for hand rework. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, delivering engineering value beyond the standalone 28-pin 8-bit MCU documentation.

Permintaan RFG Kontak

PIC18F25K83-I/ML

PIC18F25K83-I/ML - 8-bit 64MHz MCU 32KB Flash CAN | Microchip

The Microchip Technology PIC18F25K83-I/ML is an 8-bit PIC18 microcontroller with 32KB Flash, 2KB RAM, and integrated CAN technology, housed in a 28-pin QFN (ML) 6x6 mm package. Operating at up to 64 MHz with eXtreme Low Power (XLP) technology, this MCU includes a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) techniques for advanced touch sensing and supports Core Independent Peripherals (CIPs) that offload the CPU. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), data memory (RAM), and integrated peripherals. Within the broader taxonomy, the PIC18F25K83 is an 8-bit microcontroller in the PIC18 family of microcontrollers within the larger category of microcontrollers (MCUs), which are a subset of embedded processors in the semiconductor hierarchy. Unlike 32-bit MCUs, 8-bit parts like the PIC18F25K83 optimize for low power, deterministic interrupt response, and BOM cost rather than raw computational throughput. Key features of the PIC18F25K83-I/ML include 32KB Flash program memory (16K x 16 words), 2KB SRAM, 1KB EEPROM, an internal 64 MHz oscillator, and a CAN 2.0B module with dedicated DMA. The 12-bit ADC2 supports up to 24 channels, automatic averaging, oversampling, and threshold-based hardware scanning. Additional CIPs include Complementary Waveform Generators (CWG), Configurable Logic Cells (CLC), Direct Memory Access (DMA), and Zero-Cross Detect (ZCD), all running without CPU intervention. From an architectural standpoint, the PIC18F25K83 employs a Harvard RISC core with a hardware multiplier, 31-level stack, and vectored interrupt controller. Functional Safety (FuSa) features include a Windowed Watchdog Timer (WWDT), Cyclic Redundancy Check (CRC) with memory scan, hardware limits, and a 16-bit timer with dedicated low-power oscillator for safety-critical loops. Typical applications include industrial CAN nodes, automotive body controllers, capacitive touch user interfaces, sensor hubs, and low-power IoT edge nodes. The combination of CAN bus, 12-bit ADC2 with CVD, and CIPs makes the PIC18F25K83 well suited for distributed control networks and Human-Machine Interface (HMI) panels. When designing with this device, allocate sufficient PCB copper area beneath the QFN-28 exposed pad for thermal dissipation and ground reference. Use the MPLAB X IDE with MPLAB Code Configurator (MCC) to leverage the CIP library and reduce firmware development time. Always check the device errata DS80000796 for current silicon revisions before committing to production. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and CIP-driven design notes not found in the manufacturer datasheet alone, giving embedded engineers a single decision-ready reference for selecting and sourcing the PIC18F25K83-I/ML.

Permintaan RFG Kontak

PIC18F25K83-I/MX

PIC18F25K83-I/MX - 32KB Flash 8-bit MCU, CAN, 12-bit ADC² | Microchip

The Microchip Technology PIC18F25K83-I/MX is an 8-bit PIC microcontroller with 32 KB Flash, 2 KB RAM, and an integrated CAN module, packaged in a 28-pin UQFN (6x6 mm) with an exposed thermal pad. It operates up to 64 MHz from a 2.3 V to 5.5 V supply and features a 12-bit ADC with Computation (ADC²) supporting capacitive voltage divider touch sensing. An 8-bit microcontroller (MCU) is a programmable computing device that executes instructions on 8-bit-wide data. PIC microcontrollers from Microchip use a Harvard RISC architecture optimized for deterministic real-time control. The PIC18F25K83 belongs to the PIC18 K83 family which combines 8-bit CPU performance with Core Independent Peripherals (CIPs), positioning it in the broader hierarchy of microcontroller → 8-bit MCU → PIC18 → PIC18 K83 family → CAN-enabled industrial/automotive edge-node control. Key differentiating features include: ADC² with automatic averaging, oversampling, and CVD-based capacitive touch sensing; multiple Core Independent Peripherals such as CWG, CCP, NCO, and configurable logic cells (CLC); an integrated CAN 2.0B module; and a 64 MHz internal oscillator that eliminates the external crystal in many designs. The device operates over the industrial -40 °C to +85 °C range. The PIC18F25K83 integrates two SPI/I²C modules, one UART, a 12-bit ADC² with up to 24 channels, comparators, a 10-bit DAC, and a CAN controller. The CIP architecture lets peripherals (CLC, NCO, PWM, ADC², COG, CWG) interact without CPU intervention, reducing firmware complexity and deterministic latency for motor, lighting, and touch-control loops. Typical applications include industrial CAN nodes, automotive body and sensor modules, touch-control human-machine interfaces, low-power battery-powered sensor hubs, and LED lighting control. Its combination of CIPs and CAN is especially suited to networked embedded designs. Design consideration: when migrating to the UQFN-28 (MX) variant from a QFN-28 layout, confirm exposed-pad soldering to the PCB ground plane for thermal dissipation and ground integrity. The MX suffix denotes the UQFN-EP industrial-grade package. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18 K-series family, and practical CIP design notes not found in the standalone datasheet.

Permintaan RFG Kontak

PIC18F25K83-I/SP

PIC18F25K83-I/SP - 64MHz 8-bit MCU 32KB Flash CAN 28-SPDIP

The Microchip Technology PIC18F25K83-I/SP is an 8-bit PIC18 XLP microcontroller with 32KB Flash, 2KB RAM, and integrated CAN peripheral, packaged in a 28-pin SPDIP (SP) tube. It operates at up to 64 MHz CPU clock and combines Core Independent Peripherals (CIPs) with the PIC18 CAN product line, targeting automotive and industrial applications. The device also features a 12-bit ADC with Computation (ADC²) that automates Capacitive Voltage Divider (CVD) techniques for advanced touch sensing, plus 1KB EEPROM and 1KB data EEPROM for nonvolatile parameter storage. A microcontroller (MCU) is an integrated circuit containing a CPU, program memory (Flash/ROM), working memory (RAM), and configurable peripherals such as timers, ADC, communication interfaces (UART/SPI/I²C), and I/O pins on a single silicon die. Within the embedded system hierarchy, an MCU sits below an MPU (microprocessor) by integrating memory and I/O on-chip, and is a subset of the broader microcontroller > microprocessor > system-on-chip (SoC) family of semiconductor devices. The 8-bit PIC18 family uses a RISC Harvard architecture and is part of Microchip's eXtreme Low Power (XLP) line. Key features of the PIC18F25K83 include: 32KB (16K x 16) self-programmable Flash with 10K Erase/Write cycles endurance, 2KB SRAM, 1KB data EEPROM, a 12-bit ADC with Computation (ADC²) supporting up to 100K samples/sec, a 10-bit DAC module, five CCP/ECCP modules, multiple 16-bit timers, two USART, two SPI, two I²C, one CAN FD module, and 25 I/O pins. The device supports an operating voltage range of 2.3V to 5.5V (PIC18LF25K83) or 3.0V to 5.5V (PIC18F25K83), with XLP sleep currents under 50 nA typical. The PIC18F25K83 architecture combines a RISC CPU with up to 64 MHz operation, hardware-accelerated CIP blocks (CLC, NCO, 16-bit PWM, DMA), and a deterministic interrupt controller. The integrated CAN 2.0B interface enables robust in-vehicle networking, while ADC² with averaging and oversampling delivers 14-bit effective resolution for precision sensor reading. This level of integration eliminates many external components, reducing PCB area and BOM cost for connected sensor nodes. Typical applications include automotive body and comfort modules (CAN nodes), industrial sensor hubs, capacitive touch human-machine interfaces (HMIs), building automation controllers, low-power IoT edge nodes, and brushless DC motor drive controllers. The 28-SPDIP package supports easy through-hole prototyping and breadboard-compatible development. When designing with this part, ensure decoupling capacitors (100 nF and 1 µF minimum) are placed within 5 mm of the VDD pins, and that the MCLR pin is pulled high through a 10 kΩ resistor for normal operation. The CAN bus requires an external transceiver (such as MCP2551 or ATA6560) for physical-layer signaling. This page synthesizes distributor pricing for PIC18F25K83-I/SP, drop-in SPDIP alternatives from the same PIC18 K83/K80 family and cross-brand equivalents from verified web data, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25K83T-I/MX

PIC18F25K83T-I/MX - 32KB Flash 8-bit MCU w/ CAN | Microchip

The Microchip Technology PIC18F25K83T-I/MX is an 8-bit PIC18 XLP microcontroller with 32KB Flash, 2KB RAM, and integrated CAN technology, housed in a 28-pin UQFN (6x6 mm) package with exposed thermal pad. It operates at up to 64MHz and combines 15 Core Independent Peripherals (CIPs) with a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) techniques for advanced touch sensing. An 8-bit microcontroller (MCU) is a programmable computing IC that integrates a CPU, non-volatile program memory, RAM, and peripheral interfaces on a single die. Within the product hierarchy, this part sits as: MCU -> 8-bit MCU -> PIC18 family -> PIC18F2xK83 sub-family -> functional-safety-grade low-power variant. PIC18 XLP (eXtreme Low Power) parts add nanoWatt technology for sleep currents below 50 nA, making them suited to battery-powered edge nodes. The PIC18F25K83T-I/MX extends that family with a CAN 2.0B controller and FuSa (Functional Safety) support, targeting applications where deterministic fieldbus communication and IEC 61508-style documentation matter. Key features include 32KB (16K x 16) Flash program memory, 2KB SRAM, 1KB EEPROM, a 12-bit ADC with Computation (ADC2) supporting up to 38 channels, 5 CCP/ECCP modules, and 4 16-bit timers. The device supports 1.8V to 5.5V operation, four I/O ports with up to 25 digital I/O pins, and includes CLC, MMCLR, DMA, and zero-cross detect CIPs. Functional Safety documentation per IEC 61508 (SIL) and IEC 60730 (Class B) is available from Microchip for safety-critical designs. Architecturally, the part uses Microchip's enhanced PIC18 Harvard core with a 16-bit instruction path and 8-bit data path, achieving 64MHz / 16 MIPS throughput. ADC2 offloads averaging, filtering, oversampling, and threshold comparisons from the CPU, freeing MIPS for communication stacks. The CIP portfolio (CLC, NCO, DSM, CRC, DMA, CWG, PWM, COG, ZCD, HLFIN, etc.) enables complex control loops without firmware intervention, reducing BOM cost and PCB area. Typical applications include medical (motorized surgical tables, ultrasound machines), industrial (automated conveyors, asset tracking, sensor conditioning), and automotive accessories (CAN nodes, body controllers). The combination of CAN, ADC2 touch support, and XLP sleep currents also suits IoT gateways, HVAC controls, and appliance HMI. When designing with this part, validate the chosen CAN bus topology with the integrated MCP2517-style CAN-FD peripheral documentation, ensure adequate decoupling near the AVDD pin to meet ADC2 SNR targets, and review the silicon errata (DS80000852 family) before committing to layout. The 'T' suffix denotes tape-and-reel packaging and 'I' indicates the -40C to +85C industrial temperature grade. This page synthesizes distributor pricing, 8 same-package drop-in alternatives, and design notes derived from the manufacturer datasheet family, complementing the data found on DigiKey, Mouser, and Octopart listings.

Permintaan RFG Kontak

PIC18F25Q10-I/ML

PIC18F25Q10-I/ML - 8-bit 64MHz MCU, 32KB Flash, 28-QFN | Microchip

The Microchip Technology PIC18F25Q10-I/ML is an 8-bit PIC microcontroller from the PIC18-Q10 family, optimized for robust real-time control and sensor-node applications. It integrates 32KB Flash, 2KB SRAM and 256B EEPROM in a 28-pin QFN (6x6 mm) package, runs at up to 64 MHz, and supports 5V operation for increased noise immunity. The device also bundles intelligent analog peripherals and configurable Core Independent Peripherals (CIPs) such as the Complementary Waveform Generator (CWG), Configurable Logic Cells (CLC), Hardware Limit Timer (HLT), and Windowed Watchdog Timer (WWDT). An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path and a Harvard architecture, separating program and data buses for deterministic instruction fetch. The PIC18-Q10 family sits inside the PIC18 high-performance tier, which belongs to the PIC microcontroller family, then the broader 8-bit MCU category, then the microcontroller hierarchy, and ultimately the embedded processor taxonomy. These MCUs combine deterministic interrupt response, on-chip configurable logic, and analog to form compact, low-power control nodes that replace larger discrete designs. Key differentiating features include 32KB of high-endurance Flash program memory, 2KB SRAM, 256B EEPROM, a 10-bit ADC with computation (ADC2) that offloads averaging and threshold detection from the CPU, a 5-bit DAC, comparators, multiple PWM channels, and a CLC block for glue-logic replacement. The device exposes up to 25 I/O pins, supports I2C/SPI/UART, and uses Microchip's eXtreme Low Power (XLP) technology for energy-sensitive applications. Architecturally the PIC18F25Q10-I/ML uses Microchip's enhanced mid-range core with a modified Harvard bus and 16-bit instruction word, paired with a 31-level hardware stack and hardware multiply. The CWG block synthesizes complementary PWM patterns with dead-band control, enabling direct drive of half-bridge power stages, while the CLC cells implement custom logic without external gates. Typical applications include industrial sensor nodes, low-cost brushed and BLDC motor control, LED lighting drivers, home appliances, HVAC controls, and 5V noise-tolerant sensor interfaces. The 2.3V to 5.5V supply range plus 5V GPIO tolerance make it well suited to factory automation where 24V or 5V buses are common. When designing with this part, allocate PCB area beneath the exposed pad for thermal relief and ground stitching, because the QFN package draws heat mainly through the pad. Use the MPLAB X IDE with the XC8 compiler and the MPLAB Code Configurator (MCC) plugin to generate peripheral initialization code, pin maps, and CIP configuration, reducing firmware ramp-up time significantly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. (407 words)

Permintaan RFG Kontak

PIC18F25Q10-I/SO

PIC18F25Q10-I/SO - 32KB Flash 8-bit MCU, 28-SOIC | Microchip

The Microchip Technology PIC18F25Q10-I/SO is an 8-bit PIC18 microcontroller delivering 64 MIPS performance at 64 MHz, integrating 32 KB of Flash program memory, 2 KB of SRAM and 256 bytes of EEPROM in a 28-pin SOIC package. The -I/-SO suffix denotes the industrial temperature range (-40C to +85C) and SOIC wide-body 28-lead package, optimized for hand-soldering and standard SMT assembly lines. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU, non-volatile program memory, RAM, peripherals and I/O on one die. PIC18F "Q10" devices sit in Microchip's mid-range PIC18 family, which itself belongs to the 8-bit MCU category, and they target robust real-time control, sensor interfacing and low-power connected nodes with 5V operation for increased noise immunity in harsh industrial environments. Key specifications include a 10-bit ADC2 (Analog-to-Digital Converter with Computation) supporting Capacitive Voltage Divider (CVD) touch sensing, a 5-/8-bit DAC, two comparators, a 10-bit PWM with complementary outputs and a Configurable Logic Cell (CLC), alongside Core Independent Peripherals (CIPs) such as CWG, HLT, WWDT, CRC/SCAN and a hardware RTCC. The device operates from 1.8V to 5.5V (functional) and supports 5V rail operation directly, eliminating level shifters in many industrial designs. Architecturally the PIC18F25Q10 uses an enhanced Harvard architecture with a 16-bit instruction word, a hardware multiply and a 31-level hardware stack. The ADC2 block performs automated averaging, oversampling and threshold comparisons in hardware, offloading CPU cycles - useful for touch sensing and sensor fusion at low power. eXtreme Low Power (XLP) sleep currents and IDLE/DOZE modes extend battery life on sensor nodes. Typical applications include IoT sensor nodes, industrial touch-button panels, motor and BLDC control loops, HVAC controllers, and consumer device user interfaces. Designers also use the part in automotive body and interior modules under 5V environments where the larger PIC18F ecosystem, MPLAB X IDE support and a deep toolchain accelerate development. A key design consideration when selecting this MCU is pin compatibility with the smaller-memory PIC18F24Q10 in the same 28-SOIC footprint, enabling scalable designs with one PCB that can be populated with either density at low cost. Always validate ADC2 sampling time against source impedance to avoid conversion noise. This page synthesizes XAIPART distributor pricing, drop-in pin-compatible alternatives and practical PCB design notes not found in the manufacturer datasheet, helping engineers evaluate and source the PIC18F25Q10-I/SO efficiently.

Permintaan RFG Kontak

PIC18F25Q10-I/SP

PIC18F25Q10-I/SP - 32KB Flash 8-bit MCU 28-Pin SPDIP | Microchip

The Microchip Technology PIC18F25Q10-I/SP is a 32 KB Flash, 8-bit PIC microcontroller built around the enhanced mid-range PIC18 core, supplied in a 28-pin SPDIP (SP) through-hole package with industrial -40C to +85C temperature rating. The Q10 family integrates Core Independent Peripherals (CIPs), Configurable Logic Cells (CLCs), and intelligent analog blocks, allowing designers to offload timing-critical logic from the CPU and shorten firmware development cycles. Operating voltage spans 1.8V to 5.5V with on-chip voltage regulation, and 5V operation is emphasized for noise immunity in harsh industrial environments. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates a CPU, Flash program memory, SRAM data memory, EEPROM, and peripherals on a single die. Within the broader taxonomy it sits under microcontroller -> embedded controller -> integrated circuit -> semiconductor. The PIC18F25Q10 belongs to Microchip's PIC18-Q10 family, which is optimized for robust real-time control and sensor-node applications that benefit from deterministic hardware-driven behavior. Headline specifications include 64 MHz maximum CPU clock (16 MIPS at 4x PLL), 32 KB self-programmable Flash, 2 KB SRAM, 256 B EEPROM, two 10-bit ADC modules offering up to 35 channels, two comparators, two DACs, two PWMs with 16-bit resolution, CLCs, and communication peripherals comprising UART/SPI/I2C. The 5V operating range improves noise margin over 3.3V-only MCUs in motor-control and industrial sensor interfaces. The architecture leverages an 8-bit Harvard RISC pipeline with hardware multiply and 49 instruction types, supported by the MPLAB X IDE, XC8 compiler, and Microchip's MPLAB Code Configurator (MCC) for peripheral setup. Intelligent analog lets the ADC, comparator, and DAC perform hardware-triggered conversions without CPU intervention, reducing latency and jitter. Typical applications include IoT sensor nodes, motor control (BLDC, stepper), HVAC actuator control, LED lighting drivers, low-end touch HMI, battery-powered metering, and industrial automation. For automotive body electronics, the matching PIC18F25Q10-E/SP and AEC-Q100 Q10 variants provide qualified alternatives. When designing with this MCU, prioritize using CLCs for hardware state machines and the DMA-like Peripheral Pin Select to free the core for application code. Decouple VDD/VSS with 100 nF ceramic caps placed within 3 mm of the package pins, and provide bulk capacitance on AVDD if ADC accuracy is critical. This page synthesizes distributor pricing, drop-in SPDIP alternatives, and practical design notes not found in the bare manufacturer datasheet, enabling a faster PCB redesign or BOM swap than reading the 769-page datasheet end to end.

Permintaan RFG Kontak

PIC18F25Q10-I/SS

PIC18F25Q10-I/SS - 8-bit 64MHz 32KB Flash MCU | Microchip

The Microchip Technology PIC18F25Q10-I/SS is an 8-bit PIC18 microcontroller operating at up to 64 MHz (16 MIPS) with 32 KB of Flash program memory, 2 KB of SRAM and 256 Bytes of EEPROM, housed in a 28-pin SSOP package. The device operates from 2.3 V to 5.5 V and supports 5 V operation for increased noise immunity in industrial environments. It integrates a 10-bit ADC with up to 24 channels, a 5-bit DAC, comparators, PWM, CWG, HLT and a windowed watchdog timer (WWDT) into a single chip. Background Knowledge: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), peripheral interfaces and often analog blocks into one package. The PIC18 family is Microchip's 8-bit RISC architecture, optimized for low-power deterministic control in cost-sensitive embedded designs. 8-bit microcontrollers occupy the hypernym hierarchy 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. They remain preferred over 32-bit devices in applications requiring simple deterministic control loops, ultra-low sleep current, or low unit cost. Key features of the PIC18F25Q10 include eXtreme Low Power (XLP) technology with nanoWatt sleep currents, Core Independent Peripherals (CIPs) such as CWG and HLT that offload tasks from the CPU, and configurable logic cells. It supports up to 24 ADC channels at 10-bit resolution, a 5-bit DAC, two comparators with selectable references, multiple PWM modules and a Complementary Waveform Generator (CWG) suited for power-conversion feedback loops. Typical applications include industrial control, robust sensor nodes, consumer appliances, automotive body electronics, touch sensing and Internet of Things (IoT) edge nodes. The 5 V operation increases noise immunity for factory-floor installations, while the XLP peripherals make it suitable for battery-powered smart sensors. Designers should allocate the 28-pin SSOP footprint's I/O budget carefully: pin count constrains simultaneous peripheral use, and the 32 KB Flash supports roughly 16-20 KB of C application code after the bootloader reserves space. Programming is supported via Microchip's MPLAB X IDE and XC8 compiler, with ICD headers for in-circuit debug.

Permintaan RFG Kontak

PIC18F25Q10-I/STX

PIC18F25Q10-I/STX - 8-Bit MCU, 32KB Flash, 28-VQFN | Microchip

The Microchip Technology PIC18F25Q10-I/STX is an 8-bit PIC18 microcontroller from the XLP™ 18Q family, delivering 64 MHz CPU performance with 32 KB of Flash program memory and packaged in a 28-pin VQFN (4x4 mm, STX suffix). The -I temperature grade designates -40C to +85C industrial operation, well-suited for harsh-environment embedded designs. What is an 8-bit microcontroller? An 8-bit MCU is an integrated processor that executes arithmetic and logical operations on 8-bit data words. The PIC18F25Q10 belongs to the broader PIC18 microcontroller family, which sits within Microchip's 8-bit PIC architecture, itself a major branch of the microcontroller (MCU) hierarchy: MCU -> embedded processor -> semiconductor device. The "Q10" suffix identifies Microchip's low-power, high-performance sub-family featuring Core Independent Peripherals (CIPs) and intelligent analog. Key features of the PIC18F25Q10-I/STX include 32 KB Flash, 2 KB SRAM, 256 bytes of EEPROM, a 10-bit Analog-to-Digital Converter with Computation (ADC2) supporting automated Capacitive Voltage Divider (CVD) touch sensing, a Digital-to-Analog Converter, comparators, PWM, Complementary Waveform Generator (CWG), Hardware Limit Timer (HLT), and Windowed Watchdog Timer (WWDT). The device supports XLP (eXtreme Low Power) sleep currents in the nanoamp range and operates from 1.8V to 5.5V with 5V tolerance on digital I/O for noise immunity in industrial settings. In terms of architecture, the PIC18F25Q10 uses a Harvard RISC core with separate program and data buses, a configurable instruction set, and a Peripheral Pin Select (PPS) engine that lets designers remap digital peripherals to any I/O pin. ADC2 hardware-averages and oversamples conversions, offloading filtering from the CPU and reducing firmware complexity for sensor-front-end code. Typical applications include capacitive touch user interfaces, low-power sensor nodes, IoT edge devices, industrial control modules, automotive body electronics (non-safety), and battery-powered consumer appliances. The wide 1.8V-5.5V supply range and 5V-tolerance on I/O allow direct interfacing with 5V analog signals. When designing with this part, note that the 28-VQFN (4x4) footprint is shared with sibling parts such as the PIC18F24Q10, so PCB layout can be reused for a lower-memory variant. Always check Peripheral Pin Select remapping rules in MPLAB X IDE before committing to a pinout. This page synthesizes distributor pricing, drop-in replacement candidates, and practical design notes not found in the manufacturer datasheet, giving procurement and firmware engineers a single source for cross-reference, lifecycle, and sourcing decisions.

Permintaan RFG Kontak

PIC18F25Q10T-I/STX

PIC18F25Q10T-I/STX - 32KB Flash 8-bit MCU, 28-VQFN | Microchip

The Microchip PIC18F25Q10T-I/STX is an 8-bit PIC18 microcontroller built on the eXtreme Low Power (XLP) platform, integrating 32 KB of Flash program memory, 2 KB of SRAM and 256 bytes of EEPROM in a 28-pin VQFN (4x4 mm) package. It operates from 1.8 V to 5.5 V with a 64 MHz internal oscillator, while the industrial temperature grade spans -40 °C to +85 °C. What is an 8-bit PIC microcontroller? PIC microcontrollers are RISC-based, Harvard-architecture microcontrollers from Microchip that integrate CPU core, non-volatile Flash, SRAM, EEPROM and configurable peripherals on a single die. The PIC18 family extends the original PIC16 instruction set with 16-bit instructions, linear addressing, and a C-friendly compiler toolchain (MPLAB XC8). The PIC18F25Q10 belongs to the PIC18-Q10 sub-family, which adds Core Independent Peripherals (CIPs), Configurable Logic Cells (CLCs), and 5 V analog operation for noise immunity in industrial environments. Key features include a 10-bit ADC with Computation (ADC2) supporting capacitive voltage divider (CVD) touch sensing, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), and a Windowed Watchdog Timer (WWDT). The CIP set (CLC, NCO, PWM, CWG, HLT) lets designers offload timing-critical state machines from the CPU. eXLP technology delivers nanoWatt sleep currents, and the 64 MHz core yields 16 MIPS sustained throughput. The device exposes 25 digital I/O lines, supports up to two I2C, two SPI and two UART channels, and integrates an 8-bit parallel port. In real-time control and sensor-node applications, the PIC18F25Q10 balances deterministic latency, low power and analog density. The ADC2 with hardware averaging and threshold detection enables direct connection to resistive or capacitive sensors without an external op-amp. Hardware CIPs run control loops in silicon, freeing the core to sleep, which extends battery life. Compared with Cortex-M0+ parts at the same price, the PIC18-Q10 is favoured where 5 V noise tolerance, robust I/O and a long-stable toolchain matter more than raw MHz. Typical applications include sensor nodes, low-power IoT edge devices, capacitive touch user interfaces, BLDC motor control helpers, LED lighting controllers, and small industrial control boards. Designers benefit from MPLAB X IDE, MPLAB Code Configurator (MCC), and a free MPLAB XC8 compiler. A key design tip is to keep VDD decoupling within 5 mm of the pins: a 100 nF X7R plus a 1 µF X5R cap is the minimum, and the CVD reference capacitor should be a low-drift C0G/NP0 part for stable touch baselines. This page synthesises real-time distributor pricing, verified same-package drop-in alternatives and practical design notes that are not collected in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25Q43-E/SO

PIC18F25Q43-E/SO - 32KB Flash 8-bit MCU, 28-SOIC | Microchip

The Microchip Technology PIC18F25Q43-E/SO is an 8-bit PIC microcontroller from the PIC18-Q43 family, featuring 32KB of Flash program memory, 2KB of RAM, and a 64 MHz maximum CPU speed, housed in a 28-pin SOIC package. The device integrates a 12-bit Analog-to-Digital Converter with Computation (ADCC), three 16-bit PWMs with high resolution, a 5-bit DAC, a comparator, and Core Independent Peripherals (CIPs) including Configurable Logic Cells (CLCs), Direct Memory Access (DMA), and the Peripheral Pin Select (PPS) routing fabric. A microcontroller (MCU) is an integrated circuit containing a processor core, program memory, data memory, and configurable peripherals on a single silicon die, designed for embedded real-time control. The PIC18 family sits within the 8-bit MCU category in the broader semiconductor taxonomy, sharing the segment with 16-bit PIC24/dsPIC and 32-bit SAM/PIC32 devices; the Q43 sub-family is Microchip's lowest-power XLP variant targeted at real-time control and capacitive touch applications. Key differentiating specifications include 32KB self-programmable Flash with a 1KB EEPROM data region, 2KB SRAM, 64 MHz internal oscillator operation (16 MIPS throughput), 12-bit ADCC with up to 140 ksps conversion, and XLP extreme-low-power technology delivering nanoWatt sleep currents. The Q43 family introduces 16-bit PWMs that eliminate the CPU interrupt burden in motor and lighting control, and DMA channels that allow peripherals to move data without CPU intervention. Architecturally the device uses Microchip's enhanced mid-range core with a 16-bit instruction set and hardware multiply, eight-level deep hardware stack, and on-chip debug via ICD. Memory protection, code security, dual-watchdog timer, and CRC scanning make it suitable for IEC/UL safety-conscious designs. The wide 1.8V-5.5V VDD range enables single-cell Li-ion, 3.3V, and 5V system designs from one part. Typical applications include real-time motor control (BLDC, stepper, FOC), capacitive touch sensing using CVD with automatic scan, LED lighting drivers, digital power conversion, USB-to-UART bridges, sensor hubs, and consumer/IoT appliances requiring low-power sleep modes. The 28-pin SOIC footprint is pin-compatible with many PIC18F2xK42 and PIC18F2xK80 designs, simplifying board migration. When designing with the PIC18F25Q43-E/SO, leverage PPS for flexible peripheral routing and use the 16-bit PWM for motor/lighting drive to free CPU cycles. Always validate ADC acquisition time against source impedance and place VDD/VSS decoupling within 3 mm of the pins.

Permintaan RFG Kontak

PIC18F25Q43-E/SP

PIC18F25Q43-E/SP - 8-bit 64MHz MCU, 32KB Flash, XLP | Microchip

The Microchip Technology PIC18F25Q43-E/SP is an 8-bit RISC microcontroller built on the PIC18 CPU core, running at up to 64 MHz, and integrating 32 KB of Flash program memory, 2 KB of SRAM, and 1 KB of EEPROM in a 28-pin SPDIP (SP) through-hole package. It is part of the PIC18-Q43 family, which is engineered for real-time control applications combining high-performance analog and digital peripherals. According to the manufacturer datasheet (DS40002170E), the device features a 12-bit Analog-to-Digital Converter with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) techniques, plus a new 16-bit Pulse-Width Modulation (PWM) module with dual outputs. An 8-bit microcontroller (MCU) is a microprocessor integrated with memory, peripherals, and I/O on a single silicon die, optimized for embedded control tasks. The PIC architecture sits within the broader hierarchy of microcontroller -> embedded processor -> semiconductor device. The 8-bit class excels in deterministic, low-cost, low-power applications where higher-bit architectures are unnecessary, while still offering modern features such as Core Independent Peripherals (CIPs), Direct Memory Access (DMA), and Configurable Logic Cells (CLCs). Key features include up to 64 MHz operation (16 MIPS instruction throughput), eXtreme Low Power (XLP) technology for battery-friendly designs, four 16-bit timers, two I2C/SPI/UART-configurable serial interfaces, multiple PWM channels, comparators, and an 8-bit DAC. The ADCC handles automated capacitive touch sensing, averaging, filtering, oversampling, and threshold comparison, reducing firmware burden for sensor front-ends. The 28-pin SPDIP package provides easy through-hole prototyping for hobbyist, industrial, and educational designs. Typical applications include capacitive touch user interfaces, motor control with closed-loop feedback, sensor signal conditioning, LED lighting controllers, and low-power IoT edge nodes. The XLP technology makes the part especially suitable for battery-powered systems where deep sleep currents in the nanoamp range extend operational life. When designing with this device, route the analog AVCC/AGND pins with star grounding, keep ADC traces short, and place the 0.1 uF + 10 uF decoupling pair close to VDD. The SPDIP package simplifies breadboard prototyping but is typically limited to industrial operating environments; for AEC-Q100 automotive applications use the -Q43 extended grade or the QFN package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25Q43-E/SS

PIC18F25Q43-E/SS - 8-bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18F25Q43-E/SS is an 8-bit PIC18 microcontroller from the PIC18-Q43 family, featuring 32 KB of Flash program memory and operating at up to 64 MHz internal clock in a 28-pin SSOP package. It integrates a 12-bit ADC with Computation (ADCC) for hardware-accelerated capacitive touch sensing, three 16-bit PWM modules with complementary outputs, six DMA channels, configurable logic cells (CLCs), and an 8-bit DAC with 32 reference levels. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripheral interfaces on one silicon die. The PIC18F family uses an enhanced RISC architecture with a 16-bit instruction word; it sits in the hierarchy of microcontroller -> 8-bit MCU -> PIC18 family -> PIC18-Q43 sub-family -> embedded controller, and is widely deployed in real-time control applications that demand deterministic interrupt response. Key features include 32 KB Flash, 2 KB RAM, 1 KB EEPROM, a 12-bit ADCC with up to 17 analog channels, three 16-bit PWMs supporting edge- and center-aligned modes, six DMA channels, four CLCs, a 5-bit DAC with selectable reference, multiple UART/SPI/I2C interfaces, and Core Independent Peripherals (CIPs) that offload tasks from the CPU. The device uses Microchip's eXtreme Low Power (XLP) technology with sleep currents in the nanoamp range and multiple power-managed operating modes. It supports 1.8V to 5.5V VDD operation across an industrial temperature range, making it suitable for both battery-powered and line-powered designs. Typical applications include capacitive touch user interfaces, LED lighting control, motor control with closed-loop feedback, IoT sensor nodes, home appliances, and USB-to-UART bridges when paired with the PIC18F25Q43's enhanced USART. When designing with this MCU, ensure the VDD decoupling network includes 100 nF and 10 µF capacitors placed within a few millimeters of the power pin, and verify MCLR behavior for in-circuit serial programming (ICSP) headers. This page synthesizes distributor pricing, drop-in alternatives within the PIC18 family, and practical design notes that go beyond what the manufacturer datasheet provides on its own.

Permintaan RFG Kontak

PIC18F25Q43-E/STX

PIC18F25Q43-E/STX - 32KB Flash 8-bit MCU 64MHz 28-VQFN | Microchip

The Microchip Technology PIC18F25Q43-E/STX is an 8-bit PIC18 RISC microcontroller from the PIC18-Q43 family, featuring 32 KB of FLASH program memory, 2 KB of SRAM, and 1024 bytes of data EEPROM in a 28-pin VQFN (4x4) package. It executes instructions at up to 64 MHz from an internal oscillator, providing the throughput needed for real-time control loops while maintaining the family's signature eXtreme Low-Power (XLP) energy profile. The "E" suffix denotes the Extended industrial temperature range (-40C to +125C), while "/STX" identifies the Tape-and-Reel VQFN-28 4x4 mm package. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for deterministic, low-cost embedded control rather than raw computational throughput. The PIC18 family uses an enhanced Harvard architecture with separate program and data buses, and the Q43 sub-family extends the PIC18 line with advanced Core Independent Peripherals (CIPs) that let hardware blocks - not software - handle timing-critical tasks. Microcontrollers belong to the broader category of embedded processors (microcontrollers -> microcontrollers -> processors -> semiconductors), and PIC18-Q43 specifically targets real-time control, sensor signal conditioning, and user-interface applications. Key features include six Direct Memory Access (DMA) controllers, three 16-bit dual PWMs producing six PWM outputs, a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting capacitive voltage divider (CVD) touch sensing, an 8-bit DAC, configurable logic cells (CLCs), multiple UART/SPI/I2C interfaces, vectored interrupts with selectable priority, and a programmable vector table base address. The ADCC automates averaging, filtering, oversampling and threshold detection, which offloads the CPU and reduces firmware complexity in sensor and motor-control designs. The architecture integrates CIPs and 32 KB self-programmable FLASH with 10,000 erase/write cycle endurance. Programmable BOR/POR, low-voltage detection and a windowed watchdog improve robustness in industrial environments, while idle and sleep current in the nanoampere range support battery-powered edge nodes. The CIP model is the family differentiator: designers route hardware events through CLCs, PWMs and ADCC to build state machines without writing interrupt service routines. Typical applications include BLDC and stepper motor control with field-oriented control (FOC), capacitive touch human-machine interfaces (HMI), LED lighting controllers, IoT sensor nodes, household appliances, and industrial process controllers. The combination of low-power modes, fast wake-up and on-chip touch support fits sealed-keypad and battery-backed designs equally well. When designing with the PIC18F25Q43-E/STX, use MPLAB X IDE with the XC8 compiler and the MPLAB Code Configurator (MCC) for CIP and pin mapping. Always place a 0.1 uF decoupling capacitor close to each VDD pin and a bulk cap on VDD/VSS, and route the exposed thermal pad (EP) to a contiguous ground pour for thermal relief. This page synthesizes distributor pricing, drop-in VQFN-28 alternatives from the same PIC18-Q43 family, design notes and the application reference designs found in the manufacturer datasheet - information not consolidated on any single distributor page.

Permintaan RFG Kontak

PIC18F25Q43-I/SO

PIC18F25Q43-I/SO - 8-bit 64MHz 32KB Flash MCU | Microchip

The Microchip Technology PIC18F25Q43-I/SO is an 8-bit PIC microcontroller from the PIC18-Q43 family, delivering 64 MHz CPU performance with 32 KB of Flash program memory in a 28-pin SOIC package. It features 2 KB SRAM, 1 KB EEPROM, a 12-bit Analog-to-Digital Converter with Computation (ADCC), three 16-bit Pulse-Width Modulators with new high-resolution capability, Core Independent Peripherals (CIPs) including CLCs, CWG, and configurable timers, plus a 6-channel DMA controller. The wide 1.8V to 5.5V operating voltage range, eXLP nanoWatt XLP technology, and up to 36 general-purpose I/O make it ideal for real-time control applications demanding deterministic hardware behaviour. A microcontroller (MCU) is a single-chip computer integrating a CPU, non-volatile program memory (Flash), working RAM, and configurable peripherals. Within the broader taxonomy of embedded semiconductors, an 8-bit MCU sits below 16-bit DSC and 32-bit ARM Cortex-M devices in computational throughput but excels at deterministic, low-power control loops. The PIC18-Q43 family is part of Microchip's 8-bit PIC product line, designed specifically for hardware-customizable control applications. The -I suffix denotes the industrial temperature grade (-40C to +85C). Key features include the 12-bit ADCC with automated Capacitive Voltage Divider (CVD) for advanced touch sensing, oversampling and threshold comparison, plus 16-bit PWM resolution ideal for digital power and lighting control. Hardware-based signal routing through CLCs (Configurable Logic Cells) allows designers to implement glue logic without software overhead. The integrated 8-bit DAC, three analog comparators, and 5-bit DAC complement the 12-bit ADC for mixed-signal designs. The architecture uses an enhanced mid-range PIC core with a modified Harvard structure, supporting up to 64 MHz operation (16 MIPS) and multiple oscillator options including high-precision internal FRC. The DMA controller offloads repetitive data moves, freeing the CPU for application logic. This combination makes the Q43 series well suited for applications where firmware complexity is rising but BOM cost pressure still favours 8-bit silicon. Typical applications include LED lighting controllers, capacitive touch user interfaces, sensor signal conditioning, battery-powered IoT nodes, motor control peripherals, and industrial automation modules. The SOIC-28 footprint is pin-compatible with legacy PIC18F25Kxx and PIC18F25xx devices, easing migration. For real-time control designs requiring deterministic timing with hardware customization, the Q43 series stands out in the 8-bit category. When designing with this device, validate that the target board's toolchain supports the Q43 family (MPLAB X IDE, MPLAB XC8 compiler). The device operates from 1.8V to 5.5V, but certain peripherals have narrower voltage ranges - consult the datasheet for VDDMIN constraints per module. Pin-compatible migration from PIC18F25K83 is supported with attention to peripheral mapping differences. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the PIC18-Q43 and PIC18F2x families, and practical design notes not consolidated in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25Q43-I/SP

PIC18F25Q43-I/SP - 32KB Flash 64MHz 8-bit MCU | Microchip

The Microchip Technology PIC18F25Q43-I/SP is an 8-bit RISC microcontroller from the PIC18-Q43 family, featuring a 64MHz PIC18 CPU core, 32KB of FLASH program memory, 2KB of data RAM, and 1KB of EEPROM, all housed in a 28-pin SPDIP package. It operates across an industrial temperature range of -40C to +85C and supports a supply voltage range typical of PIC18F Q-series devices, with six DMA controllers that offload data movement from the CPU. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (FLASH for program code, SRAM for data, and in modern parts EEPROM or byte-programmable FLASH for non-volatile data), and a rich set of peripherals onto one die. The PIC18 family uses an 8-bit modified Harvard architecture with a 16-bit instruction word optimized for C code density, while the Q43 sub-family adds Core Independent Peripherals (CIPs) such as CLCs, 16-bit PWMs, ADCC, and DMA that execute without CPU intervention, dramatically reducing firmware complexity for real-time control loops. Key features of the PIC18F25Q43-I/SP include 64MHz maximum CPU clock (16 MIPS), six DMA channels, eight timers, three 16-bit dual PWMs (six PWM outputs total), two comparators, a 12-bit ADCC (Analog-to-Digital Converter with Computation), a 5-bit DAC, and a rich communication set of 2x SPI, 5x UART, and 1x I2C. The device also integrates a vectored interrupt controller with programmable priority and fixed three-cycle latency for deterministic real-time response. Technically, the Q43 architecture pairs the legacy PIC18 instruction set with modern CIP blocks and an interconnect fabric that lets peripherals trigger one another, enabling custom hardware state machines in silicon. This makes it suitable for both classic 8-bit embedded designs and modern IoT sensor-node applications that benefit from on-chip signal conditioning. Typical applications include IoT sensor nodes, motor control with FOC or trapezoidal commutation, LED lighting drivers, automotive body and comfort subsystems, industrial control, home appliances, and battery-powered wearables where eXtreme Low Power (XLP) modes extend operating life. When designing with this device, ensure the configuration bits are correctly programmed for oscillator selection, watchdog, and code protection. The Q43 family's pin remapping (PPS) requires careful peripheral-to-pin assignment to avoid conflicts on the limited 28-pin SPDIP footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25Q43-I/SS

PIC18F25Q43-I/SS - 32KB Flash, 64MHz 8-Bit XLP MCU | Microchip

The Microchip PIC18F25Q43-I/SS is a 32KB Flash, 2KB RAM 8-bit PIC18 microcontroller built on the XLP (eXtreme Low Power) platform, housed in a 28-pin SSOP package. It runs at up to 64 MHz, integrates a 12-bit ADCC (Analog-to-Digital Converter with Computation), three 16-bit dual PWMs (six PWM outputs), six DMA channels, an 8-bit DAC, comparators, and a functional-safety (FuSa) capable core that targets IEC 61508 SIL-2/3 designs. Operating voltage spans 1.8V to 5.5V from a single supply, with the -I/SS suffix denoting the industrial temperature grade (-40C to +85C). The 8-bit microcontroller (MCU) is a programmable system-on-chip that combines a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals. Within the broader product taxonomy the PIC18F25Q43 belongs to: 8-bit MCU -> microcontroller -> microcomputer -> embedded system IC -> semiconductor. PIC18 devices use an enhanced Harvard RISC instruction set with 16-bit opcodes that are interpreted from internal Flash, allowing linear program addressing and a small but powerful instruction footprint of 75 base instructions plus a hardware multiply and 8x8 hardware divide. Key feature highlights include 32KB self-programmable Flash with a read-while-write partition block, 2KB SRAM and 1KB EEPROM, Core Independent Peripherals (CIPs) such as CLC (Configurable Logic Cell), NCO (Numerically Controlled Oscillator), CWG (Complementary Waveform Generator), and a 12-bit differential ADCC with automated CVD (Capacitive Voltage Divider) for touch-sensing front-ends. The 12-bit ADCC can oversample, average, filter, and threshold-compare in hardware without CPU intervention - ideal for deterministic sensor acquisition. Architecturally, this part uses an enhanced PIC18 RISC core coupled with a peripheral interconnect matrix that allows DMA-driven data movement between the ADCC, DAC, comparators and PWM/DMA/CWG/CLC blocks. The XLP nanoWatt technology provides sleep currents down to a few hundred nanoamperes with full RAM retention, supporting battery-powered designs that wake periodically to make a measurement and return to sleep. Six independent DMA controllers can move data between peripherals and memory without CPU cycles, freeing the core for application logic. Typical applications include touch-interface front-ends using CVD, motor-control sub-systems using the three 16-bit PWMs, LED lighting controllers, sensor hubs, low-power IoT nodes, functional-safety sensor loops, and home appliances. The wide 1.8V to 5.5V supply range and 8-bit DAC make it a strong fit for mixed-signal nodes that previously required an external DAC. When designing with the PIC18F25Q43-I/SS, isolate the analog supply (AVDD/AVSS) and place the recommended 0.1uF plus a bulk 1uF-10uF decoupling pair within 5 mm of the supply pins. Always configure the PPS (Peripheral Pin Select) remapping before enabling peripherals, and observe the Flash write endurance (typically 10k cycles minimum on the Flash array and 100k on EEPROM). This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak

PIC18F25Q43-I/STX

PIC18F25Q43-I/STX - 32KB Flash 8-bit MCU 64MHz VQFN | XLP

The Microchip Technology PIC18F25Q43-I/STX is an 8-bit PIC18 microcontroller with 32KB Flash, 2KB RAM, and a 64MHz CPU, housed in a 28-pin VQFN (4x4 mm) package. It features a 12-bit ADC with Computation (ADCC), three 16-bit dual PWMs with six outputs, six DMA controllers, and a Vectored Interrupt controller with fixed three-cycle latency. The -I temperature grade denotes -40C to +85C industrial operating range. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash for code, SRAM for data), and programmable peripherals. The PIC18F-Q43 family sits in the 8-bit MCU tier of Microchip's portfolio, between the baseline PIC10/12/16 families and the 16-bit dsPIC/PIC24 families, optimized for real-time control with low power via XLP technology. Key features of the PIC18F25Q43 include 32KB self-programmable Flash with device ID area, 2KB SRAM, Configurable Logic Cells (CLCs), Complementary Waveform Generator (CWG), 8-bit DAC reference outputs, multiple serial interfaces (UART/SPI/I2C), and Core Independent Peripherals (CIPs) that operate without code overhead. The 12-bit ADCC supports automated Capacitive Voltage Divider (CVD) for touch sensing, averaging, oversampling, and threshold comparison. The device uses an enhanced mid-range 8-bit Harvard architecture with a 16-bit instruction word and a 31-level hardware stack, enabling deterministic interrupt response and efficient C code generation via MPLAB XC8. Six DMA channels move data between peripherals and memory without CPU intervention, freeing cycles for application logic in real-time control loops. Typical applications include LED lighting and smart-lamp controls, capacitive touch user interfaces, BLDC motor control with sensorless algorithms, digital power conversion (DC-DC, PFC), home appliance control boards, and USB-C Power Delivery (PD) controllers. The combination of CLCs, PWMs, and ADCC enables many control functions in hardware with minimal firmware. When designing with this part, ensure the supply voltage stays within 1.8V to 5.5V and provide bulk decoupling on VDD plus a 0.1uF ceramic on each VDD pin. For capacitive touch, follow the CVD layout guidelines in the datasheet to minimize noise coupling, and reserve one PWM and one CLC for timer-based housekeeping. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes beyond the manufacturer datasheet to accelerate PIC18F25Q43-I/STX evaluation and sourcing.

Permintaan RFG Kontak

PIC18F25Q43T-I/SO

PIC18F25Q43T-I/SO - 32KB Flash 8-bit MCU 64MHz 28-SOIC | Microchip

The Microchip Technology PIC18F25Q43T-I/SO is an 8-bit PIC microcontroller in the PIC18-Q43 family, offering 32 KB of Flash program memory, 2 KB of SRAM and 256 bytes of EEPROM in a 28-pin SOIC wide-body package. It runs at up to 64 MHz, supports 1.8 V to 5.5 V operation, and is qualified for the industrial -40C to +85C temperature range. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) microcontroller is a small, low-cost computer-on-a-chip that integrates a CPU core, non-volatile Flash memory, RAM, EEPROM, and a rich set of peripherals (ADC, PWM, UART, I2C, SPI, timers) on a single silicon die. PIC microcontrollers sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor IC, and are widely used wherever deterministic, low-power control is required. Key features of the PIC18F25Q43 include a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting Capacitive Voltage Divider (CVD) touch sensing, a 16-bit dual-output PWM module, six DMA controllers, three 16-bit timers, vectored interrupts with programmable priority, and Microchip's Core Independent Peripherals (CIPs) such as CLC, NCO, ZCD and PPS that allow hardware customization without CPU intervention. The eXtreme Low Power (XLP) technology delivers nanoWatt sleep currents, making the device suited to battery-powered applications. The architecture combines a RISC-style 8-bit CPU with a 16-bit instruction path, programmable peripheral pin select (PPS), and a wide tolerance for oscillator options including internal 64 MHz HFINTOSC. DMA channels move data between peripherals and memory without CPU load, while the ADCC automates averaging, oversampling and threshold comparison for advanced sensor front-ends. Typical applications include capacitive touch user interfaces, sensor node platforms, low-power IoT edge nodes, BLDC/PMSM motor control with the 16-bit PWM, LED lighting controllers, and industrial 5 V control boards. The wide 1.8 V to 5.5 V supply range lets the same firmware run from single-cell Li-ion through USB and 5 V industrial rails. When designing with this MCU, keep VDD decoupling within 1 cm of the supply pins, observe the 28-SOIC thermal envelope (theta-JA roughly 70 C/W) for high-current GPIO loads, and use the PPS feature to remap peripherals to any I/O pin. For automotive projects the PIC18F25Q43T-I/SO is industrial-grade only; the AEC-Q100 qualified variant is a separate part number. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18F25Q43 family, and practical design notes that go beyond what the manufacturer datasheet provides.

Permintaan RFG Kontak

PIC18F25Q43T-I/STX

PIC18F25Q43T-I/STX - 64MHz 8-bit MCU 32KB Flash | Microchip

The Microchip Technology PIC18F25Q43T-I/STX is an 8-bit PIC microcontroller running at 64 MHz, integrating 32 KB Flash, 2 KB SRAM, and 256 bytes of EEPROM in a 28-pin VQFN (4x4) surface-mount package with tape-and-reel packaging. It belongs to the PIC18-Q43 family of low-power, high-performance microcontrollers aimed at real-time control applications, and is rated for the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of peripherals. The PIC18 family uses an enhanced 8-bit Harvard RISC architecture with a 16-bit instruction word, while the Q43 sub-family layers modern Core Independent Peripherals (CIPs) on top of the classic PIC18 core. Within the broader taxonomy, the PIC18F25Q43 belongs to: microcontroller -> 8-bit MCU -> PIC18 -> PIC18F Q-series -> PIC18-Q43. Key differentiating features include a 12-bit Analog-to-Digital Converter with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) sensing, averaging, oversampling and threshold detection; three 16-bit Pulse-Width Modulation (PWM) peripherals; six channels of DMA; a built-in 8-bit DAC; and high-performance comparators. The XLP (eXtreme Low Power) technology and multiple low-power sleep modes enable deep-current standby for battery-operated products. Technically, the device pairs a hardware multiplier and C compiler-optimized architecture with deterministic interrupt response, hardware-acceleration blocks (CRC, zero-cross detection, signal measurement timer), and a peripheral pin select (PPS) engine that lets designers remap digital peripherals onto most I/O pins. The 28-VQFN 4x4 mm footprint exposes up to 25 GPIO and is well suited to dense analog-plus-digital mixed-signal boards. Typical applications include capacitive touch user interfaces, sensor signal conditioning with on-chip ADCC, motor and lighting PWM control, low-power IoT sensor nodes, and compact industrial control boards. The combination of touch, ADC and PWM makes it a strong fit for human-machine interface front-ends. A primary design consideration is firmware migration: the PIC18-Q43 introduces the new ADCC and revised interrupt controller, so legacy PIC18 K-series code should be re-validated against the Q43 silicon errata before reuse. Designers should also verify PPS remappings against the chosen I/O assignments in MPLAB X. This page synthesizes distributor pricing, drop-in alternatives, and application guidance not available in the manufacturer datasheet, including parametric comparison against the most common PIC18 Q/K drop-in parts in the same 28-VQFN footprint.

Permintaan RFG Kontak

PIC18F2610-E/SO

PIC18F2610-E/SO - 8-bit MCU 64KB Flash 28-SOIC | Microchip

The Microchip Technology PIC18F2610-E/SO is a high-performance 8-bit PIC microcontroller based on the enhanced PIC18 instruction set, featuring 64 KB of Flash program memory and 3968 bytes of SRAM in a 28-pin SOIC package. Operating at up to 25 MHz (40 MHz oscillator input divided by 4) with a 4.2 V to 5.5 V supply, this device delivers up to 10 MIPS performance and provides 25 digital I/O pins plus a 10-bit ADC with up to 25 channels. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC18 family specifically represents Microchip's high-performance 8-bit line, bridging traditional 8-bit simplicity with architectural enhancements such as a 16-bit wide instruction path, hardware multiplier, and C-optimized compiler support. Within Microchip's portfolio, PIC18 sits above the baseline PIC10/12/16 families and below the 16-bit PIC24/dsPIC families. Key features include 64 KB self-programmable Flash with EEPROM emulation, 3968 bytes SRAM, 1 KB EEPROM, a 10-bit A/D converter with up to 25 input channels, two analog comparators, two USART modules, MSSP (SPI/I2C), one 8/16-bit timer and three 16-bit timers, 10 PWM channels, nanoWatt power management, and in-circuit serial programming (ICSP) plus ICD debugging. The wide 4.2 V to 5.5 V supply range simplifies integration with 5 V analog and digital systems. The PIC18F2610 uses a Harvard architecture with separate program and data buses, a 16-bit instruction word, and a 10 MIPS peak throughput. The nanoWatt features (idle, sleep, and oscillator switching modes) reduce quiescent current for battery-aware designs, while the self-programmable Flash supports bootloader-style firmware updates in the field. Typical applications include industrial control panels, sensor signal conditioning, motor control PWM drivers, USB-HID/CDC peripherals (paired with the PIC18F2550/4550 family), instrumentation front ends, and embedded consumer products. The 25 MHz performance and 25 I/O pins are well matched to medium-complexity control tasks. When designing with this device, select the industrial (-40C to +85C) PIC18F2610-I/SO or extended (-40C to +125C) PIC18F2610-E/SO grade according to environmental requirements, and use the MPLAB XC8 compiler plus MPLAB PICkit 5 or ICD 4 for programming and debug. The E/SO suffix indicates the extended-temperature grade and 28-pin SOIC package. This page synthesizes distributor pricing, drop-in same-brand alternatives, application examples, and design notes to give engineers a faster decision path than the bare manufacturer datasheet.

Permintaan RFG Kontak

Subkategori

Produk (39.000+)

PIC18F25K83-E/SO - 8-Bit 64MHz 32KB Flash MCU | Microchip

PIC18F25K83-E/SP - 8-bit 64MHz 32KB Flash MCU w/ CAN | Microchip

PIC18F25K83-E/SS - 64MHz 8-bit MCU, 32KB Flash, CAN, 28-SSOP | Microchip

PIC18F25K83-I/ML - 8-bit 64MHz MCU 32KB Flash CAN | Microchip

PIC18F25K83-I/MX - 32KB Flash 8-bit MCU, CAN, 12-bit ADC² | Microchip

PIC18F25K83-I/SP - 64MHz 8-bit MCU 32KB Flash CAN 28-SPDIP

PIC18F25K83T-I/MX - 32KB Flash 8-bit MCU w/ CAN | Microchip

PIC18F25Q10-I/ML - 8-bit 64MHz MCU, 32KB Flash, 28-QFN | Microchip

PIC18F25Q10-I/SO - 32KB Flash 8-bit MCU, 28-SOIC | Microchip

PIC18F25Q10-I/SP - 32KB Flash 8-bit MCU 28-Pin SPDIP | Microchip

PIC18F25Q10-I/SS - 8-bit 64MHz 32KB Flash MCU | Microchip

PIC18F25Q10-I/STX - 8-Bit MCU, 32KB Flash, 28-VQFN | Microchip

PIC18F25Q10T-I/STX - 32KB Flash 8-bit MCU, 28-VQFN | Microchip

PIC18F25Q43-E/SO - 32KB Flash 8-bit MCU, 28-SOIC | Microchip

PIC18F25Q43-E/SP - 8-bit 64MHz MCU, 32KB Flash, XLP | Microchip

PIC18F25Q43-E/SS - 8-bit 64MHz 32KB Flash MCU | Microchip

PIC18F25Q43-E/STX - 32KB Flash 8-bit MCU 64MHz 28-VQFN | Microchip

PIC18F25Q43-I/SO - 8-bit 64MHz 32KB Flash MCU | Microchip

PIC18F25Q43-I/SP - 32KB Flash 64MHz 8-bit MCU | Microchip

PIC18F25Q43-I/SS - 32KB Flash, 64MHz 8-Bit XLP MCU | Microchip

PIC18F25Q43-I/STX - 32KB Flash 8-bit MCU 64MHz VQFN | XLP

PIC18F25Q43T-I/SO - 32KB Flash 8-bit MCU 64MHz 28-SOIC | Microchip

PIC18F25Q43T-I/STX - 64MHz 8-bit MCU 32KB Flash | Microchip

PIC18F2610-E/SO - 8-bit MCU 64KB Flash 28-SOIC | Microchip