Produk (42.000+)

WM8144CPT - 10-Bit CCD Imaging Data Converter | Texas Instruments
WM8144CPT

WM8144CPT - 10-Bit CCD Imaging Data Converter | Texas Instruments

The Texas Instruments WM8144CPT is an integrated 10-bit data-acquisition system for imaging applications, packaged in a 27-pin CPT surface-mount package. It combines the analog signal-conditioning functions required by CCD sensors with a 10-bit ADC and optional pixel-by-pixel image compensation. The supplied source identifies WM8144CPT as an audio-channel IC, while the family description identifies WM8144 as an integrated CCD-imaging data-acquisition system. Those descriptions should be reconciled against the original manufacturer documentation before using the part in a new design. A CCD image sensor is a semiconductor that converts accumulated light into analog charge and transfers that charge through output circuitry in a sequence. Because the resulting signal is weak, noisy, and often offset or gain mismatched, imaging systems require conditioning before digital conversion. An integrated data-acquisition IC reduces discrete circuitry and helps standardize the interface between the sensor output amplifier, analog-to-digital converter, and image-processing electronics. The WM8144 family provides the core functions needed for imaging: CCD-compatible analog signal conditioning, a 10-bit ADC, and optional pixel-by-pixel compensation. Compensation circuitry is used to correct sensor-column offsets, gain variations, dark current, or fixed-pattern effects before pixels are interpreted. The practical benefit is a more compact analog section, but final image quality still depends on sensor characteristics, clocking, grounding, reference quality, and system calibration. The exact suffix CPT denotes the supplied package/orderable variant, but the verified source set does not expose the full pin list, electrical ratings, ADC conversion rate, voltage limits, clock requirements, or operating-temperature limits. Consequently, those values are not inferred here. The 27-page document count reported by a search result is a page count, not proof of the target package pin count, so it is not used to construct a pinout or package drawing. Typical imaging uses include scientific CMOS-compatible signal chains, industrial line-scan cameras, low-light surveillance modules, barcode and document scanners, machine-vision cameras, and embedded optical measurement systems. In each case, the sensor amplifier output must meet the WM8144 input range and sampling requirements. Because those limits are unavailable in the supplied data, a new design should treat them as release-gating requirements and verify them in the original datasheet. Layout is especially important because CCD outputs are high impedance and susceptible to coupling, ground noise, and reference disturbance. Place the device close to the sensor output, keep the analog path compact, isolate clocks from sensitive traces, and return unused inputs according to the verified pin documentation. Use a stable, low-noise reference and suitable bypass capacitors once their required values are confirmed from the manufacturer guidance. This page distinguishes documented WM8144-family functions from unverified target-variant specifications, lists the supplied sourcing records, and avoids fabricating pin assignments, ratings, lifecycle claims, stock levels, or prices. Engineers should download and review the original WM8144 documentation before layout release, schematic sign-off, or production procurement.

Permintaan RFG Kontak
WM8152SCDS/V - 16-Bit Single-Channel CIS/CCD AFE | Cirrus Logic
WM8152SCDS/V

WM8152SCDS/V - 16-Bit Single-Channel CIS/CCD AFE | Cirrus Logic

The Cirrus Logic WM8152SCDS/V is a single-channel 16-bit analog front end and digitizer for CCD sensors and contact image sensors, operating at pixel sample rates up to 12 MSPS in a 20-lead SSOP package. It includes a 5 V analog supply requirement, digital supply support from 2.97 V to 3.63 V or 5 V, and a listed power dissipation of 225 mW. An analog front end, or AFE, is the interface between a sensitive image sensor and the digital signal-processing system. It conditions the small sensor signal, controls timing and correlated double sampling, performs analog-to-digital conversion, and presents digitized image data to an external processor. The WM8152SCDS/V belongs to the broader CMOS image-sensor interface and data-conversion hierarchy, combining sensor analog conditioning with a 16-bit digitizer. The WM8152SCDS/V is identified as a single-channel device with 16-bit resolution and a maximum pixel rate of 12 MSPS. The manufacturer describes it as a CIS/CCD AFE with 4-bit wide output, making it suitable for scanners, imaging modules, and compact image-processing systems. Its 20-SSOP package provides a conventional surface-mount footprint for equipment where board area and production compatibility are important. The analog supply is specified at 5 V, while the digital interface can operate from either 2.97 V to 3.63 V or 5 V. This flexibility allows the digitizer to operate with either 3.3 V or 5 V digital system logic when the external interface, timing, and signal-integrity requirements are satisfied. The device is designed for CMOS image-sensor signal chains rather than general-purpose audio or instrumentation conversion. Typical uses include contact image sensors in scanners, CCD-based imaging assemblies, document-capture systems, and other pixel-oriented imaging products. In these applications, the AFE is placed close to the image sensor so that the weak analog signal is conditioned and digitized before long PCB traces introduce additional noise or distortion. A key design consideration is separating the analog and digital return paths while keeping the sensor interface traces short. The power-supply network should provide low-impedance connections for both the 5 V analog rail and the selected digital rail, and the input and output routing should follow the manufacturer’s pin and layout guidance. The 225 mW listed power value should also be checked against the system’s thermal envelope during sustained operation. This product record combines the manufacturer-described AFE function, the listed electrical and packaging characteristics, source links for documentation and purchasing, and practical application guidance for CIS and CCD imaging designs.

Permintaan RFG Kontak
WM8196SCDS/V - 16-Bit 12 MSPS 3-Channel AFE | Cirrus Logic
WM8196SCDS/V

WM8196SCDS/V - 16-Bit 12 MSPS 3-Channel AFE | Cirrus Logic

Cirrus Logic WM8196SCDS/V is a 16-bit, three-channel analog front end and digitizer for CCD sensors and contact image sensors, operating at pixel sample rates up to 12 MSPS in a 28-pin SSOP package. The device combines analog signal conditioning with high-speed digitization. An analog front end is an interface between a sensitive imaging sensor and an electronic system. It conditions the small analog signals produced by CCD or CIS pixels before conversion into digital data. In the broader device hierarchy, an AFE precedes an ADC, which forms part of a data-conversion system and ultimately supports image acquisition, scanning, inspection, and machine-vision processing. The WM8196SCDS/V provides three analog processing channels, each incorporating reset-level clamping, correlated double sampling, and programmable gain and offset adjustment. Three internal multiplexers support single-channel processing, while a shared high-speed ADC time-multiplexes the channel outputs. According to the manufacturer datasheet, the digital output uses an 8-bit plus 8-bit data organization. The device supports a 12 MSPS pixel sampling rate and delivers 16-bit digitized image data, making it appropriate for CCD and CIS imaging systems that require more scan-line throughput than a general-purpose low-speed ADC provides. Its analog supply is 5 V, while the digital interface can operate from 2.97 V to 3.63 V or 5 V, allowing integration with both 3.3 V and 5 V digital systems. Typical uses include document scanners, flatbed scanners, contact-image-sensor scanners, industrial inspection equipment, and compact imaging modules. Each analog channel can apply calibrated gain and offset to compensate for pixel and sensor variation before the multiplexed ADC performs conversion. The main design consideration is the relationship among sensor timing, analog signal conditioning, output data capture, and clocking. The three channels and their multiplexers must be configured for the intended sensor arrangement, and the digital interface must match the host processor voltage and data-capture method. Power and grounding also require care because sensor signals pass through high-gain analog stages before digitization. This page consolidates the manufacturer electrical information, package details, application guidance, comparison parameters, and practical design notes into one engineering reference. It also distinguishes verified drop-in alternatives from packaging variants that do not constitute meaningful component substitutions.

Permintaan RFG Kontak
WM8199SCDS/V - 3-Channel 16-Bit 20MSPS AFE | Cirrus Logic
WM8199SCDS/V

WM8199SCDS/V - 3-Channel 16-Bit 20MSPS AFE | Cirrus Logic

Cirrus Logic WM8199SCDS/V is a three-channel, 16-bit analog front end and digitizer capable of processing CCD and contact image sensor outputs at pixel sample rates up to 20MSPS. The device is supplied in a 28-pin SSOP package and is listed with a power dissipation of 358 mW. An analog front end, or AFE, is an interface circuit that conditions analog sensor signals before digitization. Its role in the signal chain is to prepare incoming CCD or contact image sensor voltages for accurate conversion by an ADC. Within the broader hierarchy, an AFE is a data-acquisition IC, an interface IC, and ultimately a semiconductor designed to bridge specialized analog sensors with digital image-processing systems. The WM8199SCDS/V provides three signal-processing channels, 16-bit digitization, and operation to 20MSPS. These headline specifications make it suitable for multichannel scanner, contact image sensor, and industrial imaging systems that require synchronized conversion of narrow pixel signals. Its three-channel architecture can reduce the number of separate front-end devices needed when a sensor exposes multiple outputs. The 20MSPS maximum sample rate establishes the upper conversion-speed limit for each supported channel. It determines how rapidly successive pixel positions can be processed and is important when matching the AFE to sensor timing, clocking, and downstream image throughput. The 16-bit digital output provides substantially greater numerical resolution than lower-bit converters, supporting precise capture of gradual signal changes. The WM8199SCDS/V is specifically associated with CCD sensors and contact image sensors rather than general-purpose audio or instrumentation front ends. Typical application areas include document scanners, flatbed scanners, contact image sensor modules, inspection equipment, and other imaging systems that require three analog inputs, 16-bit conversion, and a maximum sampling rate of 20MSPS. System design must preserve the relationship between sensor pixel rate, analog input bandwidth, clocking, and the downstream image processor. The AFE should be placed close to the sensor outputs, with a low-noise and appropriately terminated reference arrangement. Power distribution and grounding require care because converter performance is influenced by supply noise and signal return paths. This product page combines the WM8199SCDS/V technical identity, package information, application guidance, sourcing details, and cross-reference analysis in a format intended to accelerate component selection and board-level implementation. It also emphasizes the distinction between a true pin-compatible replacement and a merely similar imaging converter.

Permintaan RFG Kontak
WM8213SCDS/V - 16-Bit 3-Channel 24MSPS AFE | Cirrus Logic
WM8213SCDS/V

WM8213SCDS/V - 16-Bit 3-Channel 24MSPS AFE | Cirrus Logic

Cirrus Logic WM8213SCDS/V is a 3-channel, 16-bit analog front end and digitizer designed for CCD sensors and contact image sensors, with a maximum sampling rate of 24 MSPS and power consumption of 350 mW. The device is supplied in a 28-pin SSOP package measuring 5.30 mm in body width. An analog front end, or AFE, converts weak sensor signals into digital data while performing the analog conditioning needed before conversion. The AFE sits between the optical sensor and the digital system, performing sensor-level clamping, correlated double sampling, programmable gain and offset adjustment, and channel multiplexing. In the hierarchy of electronic components, the WM8213SCDS/V is an AFE, ADC, signal-chain IC, and semiconductor intended for high-speed imaging systems. The WM8213SCDS/V includes three independent analog signal-processing channels. Each channel provides reset-level clamping, correlated double sampling, and adjustable gain and offset functions. Three analog multiplexers support channel selection, while the processed signals are time-multiplexed into one high-speed 16-bit ADC. This architecture reduces the number of separate converters required in a multichannel imaging system and concentrates the digitized output into a common serial interface. Its 24 MSPS pixel sampling capability is suitable for CCD and CIS imaging systems that require high-speed transfer of image data. The 16-bit ADC resolution provides 65,536 quantization levels, while the 350 mW device rating indicates a relatively low power demand for a three-channel high-resolution imaging front end. Analog and digital operating supplies are both specified from 2.97 V to 3.63 V, supporting a 3.3 V system environment. Typical uses include line-scan cameras, contact image sensors, document scanners, barcode and inspection equipment, and other optical acquisition systems in which multiple sensor outputs require correlated sampling and shared digitization. The three-channel architecture is particularly useful when the imaging system must process more than one sensor signal without deploying three complete standalone ADC channels. PCB implementation should preserve short, controlled analog paths between the sensor outputs and the corresponding AFE inputs. Decoupling capacitors should be placed close to the supply pins, while the serial digital outputs require a compact, impedance-controlled layout away from the analog inputs. The 28-pin SSOP footprint also requires adequate board width and careful lead-clearance planning during inspection or assembly. This product summary combines the WM8213SCDS/V electrical ratings, architecture, package characteristics, sourcing information, and design guidance into one engineering reference. It also distinguishes verified operating facts from parameters that must be confirmed in the manufacturer datasheet before a new sensor board is released.

Permintaan RFG Kontak
WM8214SCDS/V - 16-Bit 3-Channel 40MSPS AFE | Cirrus Logic
WM8214SCDS/V

WM8214SCDS/V - 16-Bit 3-Channel 40MSPS AFE | Cirrus Logic

The Cirrus Logic WM8214SCDS/V is a 16-bit, three-channel analogue front end (AFE) and CCD digitiser that converts analogue sensor outputs at pixel sample rates up to 40 MSPS, operated from 2.97 V to 3.63 V on both the analog and digital rails, and dissipating 390 mW. It is packaged in a 28-SSOP surface-mount package with a 0.209 in (5.30 mm) body width. The /V suffix identifies the lead-free ordering option of the original Wolfson Microelectronics WM8214SCDS device. An analogue front end is the signal-conditioning and conversion block that sits between an imaging sensor and a digital processor. It takes the weak, noisy analogue charge or voltage signal produced by a CCD or CIS sensor, applies gain, offset and timing control, and then performs the analogue-to-digital conversion that turns the sensor waveform into numeric pixel data. In the product hierarchy, an AFE is a data-acquisition IC, which is a subclass of mixed-signal and interface semiconductors used in imaging, instrumentation and industrial automation systems. Key features of the WM8214SCDS/V include 16-bit conversion resolution, three parallel channels for multi-phase sensor timing, a maximum pixel sampling rate of 40 MSPS, a single 2.97 V to 3.63 V supply range shared by the analog and digital sections, and a compact 390 mW power dissipation in an industry-standard 28-SSOP footprint. The combination of three channels and 40 MSPS throughput allows one device to digitise the output of a three-output CCD or CIS sensor without external multiplexers or separate converter ICs. The WM8214SCDS/V integrates the full imaging signal chain into a single package: analog conditioning, sampling, conversion and digital output in one device. Separate analog and digital supply pins allow a system architect to partition noisy digital return currents from the sensitive analog reference and signal planes, which is the standard technique used to reach the noise floor required for 16-bit resolution. Because the converter runs directly from the sensor clock, no external sample-and-hold stage or external ADC is required between the CCD output amplifiers and the digital back-end. Typical applications include flatbed contact image sensor (CIS) scanner signal chains, line-scan CCD machine vision modules, copier and multi-function printer imaging engines, industrial inspection and optical metrology equipment, portable and handheld document scanners, and dedicated barcode or document imaging modules. The 40 MSPS sampling ceiling covers the pixel rates of mainstream office and industrial CIS strips, while the three-channel architecture matches typical three-phase or multi-output CCD timing schemes. A key design consideration is supply partitioning and decoupling. Because the analog and digital sections use separate supply pins within the same package, route them on distinct planes and place the analog bypass capacitors directly at the analog supply pins to avoid shared-impedance coupling of switching noise into the signal path. The 28-SSOP body also limits total copper area, so keep the analog ground return path short and directly beneath the device. This page consolidates device specifications, supply voltage and power limits, package and ordering information, drop-in alternatives from the same Cirrus Logic imaging AFE family, and practical PCB design notes into a single reference for engineers evaluating the WM8214SCDS/V for CCD and CIS imaging designs.

Permintaan RFG Kontak
WM8215CSEFL - 3-Channel 10-Bit 60MSPS CCD/CIS AFE | Cirrus Logic
WM8215CSEFL

WM8215CSEFL - 3-Channel 10-Bit 60MSPS CCD/CIS AFE | Cirrus Logic

The Cirrus Logic WM8215CSEFL is a 3-channel, 10-bit analog front end (AFE) for CCD and CIS image sensors, sampling at up to 60 MSPS per channel while consuming approximately 400 mW of power, housed in a 32-pin QFN (5x5 mm) package. An analog front end for image digitisation is the circuit block that sits directly between a photosensitive sensor and the digital image processor. CCD and CIS sensors output small, correlated-double-sampling (CDS) dependent analog charges that must be conditioned, clamped, sampled and converted to digital words with matched timing across multiple channels. The AFE therefore combines programmable gain, offset correction, black-level clamping, CDS sampling and a multi-channel ADC pipeline in one integrated circuit, forming part of the broader signal-chain hierarchy: sensor -> AFE -> ADC -> image processor -> system. Key features of the WM8215 include three independent 10-bit conversion channels rated at 60 MSPS, a total power dissipation of around 400 mW, and support for both CCD and CIS sensor architectures. The part is fabricated in CMOS, which keeps quiescent consumption low and supports dense multi-channel integration. Wolfson Microelectronics, the original designer, was acquired by Cirrus Logic, so datasheets may appear under either brand name. Architecturally, the WM8215 uses a pipelined 10-bit ADC per channel preceded by input conditioning stages, allowing each colour channel of a linear sensor array to be digitised simultaneously. Simultaneous sampling eliminates inter-channel skew artefacts such as colour fringing in line-scan imaging, which sequential multiplexed converters cannot avoid. Typical applications include document scanners and multi-function printers with CIS arrays, industrial line-scan inspection cameras, machine-vision systems for surface inspection, and scientific or medical linear CCD readout chains where three matched channels map naturally to RGB or multi-tap sensor outputs. A key design consideration is signal integrity: keep the analog input traces short, guard them with ground, and follow the manufacturer datasheet for reference-decoupling and CDS timing, since jitter or noise on the sampling clock converts directly into image fixed-pattern noise. Thermal dissipation of 400 mW should be managed with the QFN exposed pad soldered to a ground pour. This page synthesises distributor availability, package and application data, and practical design notes not found in the manufacturer datasheet, and it is verified and refreshed against distributor listings.

Permintaan RFG Kontak
WM8224CSEFL - 60 MSPS 3-Channel AFE | Cirrus Logic
WM8224CSEFL

WM8224CSEFL - 60 MSPS 3-Channel AFE | Cirrus Logic

Cirrus Logic WM8224CSEFL is a three-channel analog front end (AFE) for high-speed digital video and audio conversion, featuring programmable resolution of 8, 10, 12, or 16 bits and operation up to 60 MSPS. The device uses a 32-VFQFN package with an exposed pad and operates from 2.97 V to 3.63 V for both analog and digital supplies. Its typical power consumption is 360 mW, making it suitable for compact, multichannel signal-chain designs requiring controlled ADC front-end performance. An analog front end is an integrated signal-conditioning and conversion stage that sits between analog sensors or video inputs and a digital processor. It combines analog input conditioning, programmable gain, sampling, filtering, and conversion functions in one device. The WM8224 belongs to the broader ADC and data-converter hierarchy, with the AFE adding channel multiplexing and signal-conditioning functions that are normally implemented as separate components. The WM8224CSEFL provides three independently addressed input channels and supports multiple-device operation, allowing additional AFEs to be coordinated in larger systems. Programmable automatic black-level calibration supports imaging and video applications where the black reference must track component and signal-chain variation. Resolution can be configured across 8, 10, 12, and 16 bits, giving designers flexibility to balance conversion detail, data rate, and power requirements. Its analog and digital supply ranges of 2.97 V to 3.63 V align with common 3.3 V system rails. The 32-VFQFN, 5 x 5 mm package includes an exposed thermal pad for improved heat dissipation, but the layout must provide adequate copper area and a low-impedance ground connection. The AFE's 60 MSPS capability is suitable for video capture, image processing, surveillance, communications, and other multichannel sampling systems. Applications include three-channel video sensor interfacing, industrial imaging, document scanners, machine vision, surveillance cameras, and multichannel signal acquisition. For each design, confirm the selected operating mode, channel assignment, clocking arrangement, and black-level calibration strategy against the manufacturer datasheet. The input network, decoupling capacitors, analog ground, digital return paths, and exposed-pad thermal design are especially important in high-speed layouts. This page consolidates the WM8224CSEFL device identity, key electrical and package characteristics, sourcing information, design guidance, and verified drop-in alternatives. It also distinguishes the exact MPN from family-level references so procurement and PCB decisions are based on a traceable device configuration.

Permintaan RFG Kontak
WM8232GEFL/V - 16-Bit 3-Channel AFE | Cirrus Logic
WM8232GEFL/V

WM8232GEFL/V - 16-Bit 3-Channel AFE | Cirrus Logic

Cirrus Logic WM8232GEFL/V is a three-channel, 16-bit analog front end operating at up to 70 MSPS, with sensor timing generation and selectable LVDS or CMOS data outputs in a 56-QFN 8 x 8 mm package. Its analog and digital supply ranges are both 2.97 V to 3.63 V, supporting compact, low-voltage imaging systems. An analog front end, or AFE, combines analog signal conditioning and data conversion at the input of a digital processing system. In the product hierarchy, the WM8232GEFL/V belongs to the ADC/DAC class of integrated circuits and converts weak or noisy sensor signals into digital data. Its three processing channels reduce the need for separate amplifiers, clamp circuits, sampling circuits, gain stages, and offset-adjust networks. Each channel includes reset-level clamping, correlated double sampling or sample-and-hold, programmable gain, automatic gain control, and offset adjustment. These functions improve the usable dynamic range of the incoming analog signal before digitization. The 16-bit conversion resolution preserves fine signal detail, while the integrated AGC reduces the workload required from the downstream image processor. Sensor timing generation coordinates frame acquisition, while the LVDS and CMOS output options provide flexibility in board architecture. LVDS is useful when a design requires a high-speed differential link with good noise immunity; CMOS offers a simpler single-ended interface where board-level signal integrity is easier to manage. Both output configurations support 3.3 V-class digital systems represented by the 2.97 V to 3.63 V supply range. Typical uses include industrial image sensors, machine-vision cameras, medical imaging equipment, surveillance cameras, barcode scanners, and embedded optical measurement systems. Three integrated channels are particularly useful for color imaging, stereo sensing, or multichannel sensor configurations where synchronized acquisition and consistent channel calibration are important. The principal design consideration is interface implementation. Confirm the selected LVDS or CMOS output mode, external clocking requirements, sensor timing, and exposed-pad thermal arrangement against the manufacturer pin and layout documentation. Power and ground distribution must keep analog and return currents controlled because converter clocking and data-output switching can introduce noise into the sampled signal. This product overview consolidates the channel architecture, conversion performance, supply limits, output options, and application guidance into an engineering-focused reference. It also highlights the practical checks needed to evaluate the WM8232GEFL/V in a new sensor-processing board.

Permintaan RFG Kontak
WM8233GEFL/V - 16-Bit 6-Channel 70 MSPS AFE | Cirrus Logic
WM8233GEFL/V

WM8233GEFL/V - 16-Bit 6-Channel 70 MSPS AFE | Cirrus Logic

The Cirrus Logic WM8233GEFL/V is a six-channel, 16-bit analog front end and digitizer designed for high-speed CCD and contact image sensor signal chains. It supports pixel sampling rates up to 22.5 MSPS per channel, while its distributor descriptions identify the device family as a 70 MSPS six-channel AFE. The component is packaged in a 56-pin VFQFN package measuring 8 mm by 8 mm with an exposed pad. An analog front end, or AFE, is an interface IC that conditions, samples, and converts sensor signals into digital data. The AFE category sits between the sensor and the digital processing system: CCD or CIS outputs enter the AFE, programmable analog processing prepares those signals, and the resulting high-speed data is delivered to a processor or image pipeline. WM8233 belongs to this broader class of high-speed mixed-signal semiconductor and sensor-interface IC. The WM8233 provides six analog signal-processing channels, each incorporating reset-level clamping, correlated double sampling, sample-and-hold circuitry, and programmable gain according to the manufacturer datasheet. Its 16-bit conversion resolution preserves fine amplitude detail in imaging systems. Programmable operating modes, sensor timing generation, and selectable CMOS or LVDS data outputs allow the interface to be adapted to different sensor and back-end requirements. WM8233GEFL/V operates from a 2.97 V to 3.63 V analog supply range. The manufacturer documentation also describes a separate digital supply, supporting independent control of analog and digital power domains. This separation can help designers isolate sensitive analog processing from digital-interface noise while maintaining a common 56-pin package and compact 8 mm by 8 mm footprint. Typical applications include linear CCD scanners, contact image sensors, document imaging systems, industrial inspection equipment, and other multichannel imaging platforms. Six integrated channels are particularly useful where multiple sensor outputs must be sampled coherently. The timing-generation and data-output functions reduce the external control burden associated with synchronizing sensor transfer, sampling, and digital readout. Designers should place input, reference, and digital-output connections for controlled impedance, maintain the analog and digital return paths separately, and use the exposed thermal pad with an appropriate PCB ground and thermal layout. The pin and exposed-pad connections should follow the manufacturer pin-description table and recommended land pattern exactly. Because this device is listed as NRND, new designs should confirm lifecycle and sourcing requirements before committing to production. This product page consolidates the verified channel count, resolution, sampling-rate descriptions, supply range, package, lifecycle status, and sourcing information. It also distinguishes electrically similar Cirrus Logic devices from verified drop-in replacements and provides practical guidance for evaluating the WM8233 in CCD and CIS imaging systems.

Permintaan RFG Kontak
WM8234GEFL/V - 6-Channel 16-Bit 70MSPS AFE | Cirrus Logic
WM8234GEFL/V

WM8234GEFL/V - 6-Channel 16-Bit 70MSPS AFE | Cirrus Logic

The Cirrus Logic WM8234GEFL/V is a six-channel, 16-bit analog front end and digitizer optimized for CCD and contact image sensor imaging systems. It supports pixel sampling rates up to 23MSPS per channel, operates at up to 70MSPS, and includes sensor timing generation with LVDS and CMOS data outputs. The device is packaged in a 56-QFN 7 x 7 mm surface-mount package. An analog front end converts charge or voltage signals from an imaging sensor into digitized image data. In the broader signal-chain hierarchy, the WM8234 belongs to the analog front end and digitizer class, which sits ahead of an image processor or frame grabber. It is designed for scanners, copiers, fax machines, and industrial line-scan systems where multiple sensor outputs must be sampled with consistent timing and high resolution. The WM8234 provides six analog processing channels, each incorporating reset-level clamping, correlated double sampling or sample-and-hold, programmable gain, automatic gain control, and offset adjustment. Its sensor timing generator accepts slow or fast reference clocks and permits flexible adjustment of the output timing clocks. A 5-bit internal DAC generates reference levels for correlated double sampling of CIS signals or for clamping CCD signals. The device supports flexible data-output configurations, including LVDS and CMOS interfaces, allowing the digitizer section to connect to a variety of downstream image-processing or data-capture systems. Programmable analog functions help normalize channel gain and offset before digitization, reducing fixed-pattern variation in the resulting image. The 16-bit conversion resolution and six-channel architecture suit imaging systems that require multiple parallel sensor lines rather than a single slow-speed channel. Typical uses include CCD-based document scanners, contact image sensor modules, color and monochrome copiers, and industrial imaging equipment. The integrated timing generator is particularly useful where sensor clocks must be derived from a common system reference and distributed with controlled phase relationships across multiple channels. The WM8234GEFL/RV ordering code provides the same core electrical function in a different packing arrangement. When laying out the board, treat the analog inputs, timing outputs, and high-speed data interface as separate constraint groups. Keep sensor traces short, maintain continuous reference planes beneath the analog section, and follow the manufacturer’s recommended decoupling and via-stitching arrangements around the exposed pad. Confirm the selected output interface, reference-voltage configuration, sensor timing mode, and pin mapping in the manufacturer datasheet before releasing a PCB layout.

Permintaan RFG Kontak
WM8235GEFL/V - 16-Bit 9-Channel 70 MSPS AFE | Cirrus Logic
WM8235GEFL/V

WM8235GEFL/V - 16-Bit 9-Channel 70 MSPS AFE | Cirrus Logic

The Cirrus Logic WM8235GEFL/V is a 16-bit, 9-channel analog front end and digitizer for CCD sensors and contact image sensors, operating at up to 70 MSPS with sensor timing generation and LVDS or CMOS data outputs. It accepts analog and digital supply voltages from 2.97 V to 3.63 V and is packaged in a 56-VFQFN exposed-pad package measuring 7 mm by 7 mm. An analog front end is an integrated signal-processing IC positioned between an imaging sensor and a digital image processor. Within the broader integrated-circuit hierarchy, an AFE is a data-acquisition component combining analog conditioning, sampling, and digital conversion. The WM8235 performs nine parallel sensor signal paths, allowing a scanner, copier, or imaging module to digitize multiple outputs while maintaining coordinated timing. Each of the nine analog channels includes reset-level clamping, correlated double sampling or sample-and-hold, programmable gain, automatic gain control, and offset adjustment. These functions allow the WM8235GEFL/V to condition sensor outputs before conversion. The device supports a 16-bit conversion resolution and can process sensor signals at pixel sample rates up to 23 MSPS per channel, according to the manufacturer datasheet. The WM8235 family also generates the sensor timing signals required to transfer charge and reset information from the imaging array. Programmable timing, channel-level signal conditioning, and integrated digitization reduce the number of external analog components needed around a sensor. Output data can be delivered through LVDS or CMOS interfaces, providing configuration flexibility for different imaging systems and downstream processors. Typical applications include flat-panel scanners, document copiers, multifunction printers, contact image scanners, and other CCD- or CIS-based imaging equipment. Its 9-channel architecture is particularly useful when an imaging module presents several sensor outputs that must be sampled consistently. The 3.3 V operating range also simplifies integration with contemporary 3.3 V digital systems. PCB design should provide a low-impedance analog and digital ground structure, place decoupling capacitors close to the supply pins, and use controlled-impedance routing for high-speed CMOS or LVDS outputs. The exposed pad requires a thermal and electrical land pattern specified by the manufacturer datasheet; it must not be treated as an unused mechanical feature. This page combines the WM8235GEFL/V device specifications, verified manufacturer and distributor listings, package information, application guidance, and engineering design notes. It also distinguishes documented device functions from sourcing questions so engineers can evaluate the AFE quickly and consult the manufacturer datasheet for implementation details.

Permintaan RFG Kontak
WM8253SCDS/RV - 16-Bit 6MSPS Single-Channel AFE | Cirrus Logic
WM8253SCDS/RV

WM8253SCDS/RV - 16-Bit 6MSPS Single-Channel AFE | Cirrus Logic

Cirrus Logic WM8253SCDS/RV is a single-channel, 16-bit analog front end for CIS and CCD image sensors, operating at up to 6 MSPS with a 3.3 V supply and 132 mW power consumption. The device is packaged in a 20-pin SSOP with a 4-bit wide output interface and is supplied in tape-and-reel packaging. An analog front end, or AFE, is the interface between an imaging sensor and the digital processing system. Its sensor-side input circuitry conditions the charge or voltage generated by a CMOS image sensor or CCD, while its internal ADC converts the conditioned analog signal into digital data. Within the image-signal chain, the AFE sits between the optical sensor and the ISP, FPGA, image processor, or system controller. The WM8253SCDS/RV combines this analog conditioning function with a single-channel 16-bit conversion stage. The principal device characteristics include one analog input channel, 16-bit conversion resolution, a maximum sampling rate of 6 MSPS, 3.3 V operation, and 132 mW power. Its 4-bit wide output provides a compact connection to downstream digital circuitry. The 20-SSOP package is suitable for surface-mount assembly in imaging modules where component density, converter resolution, and sampling speed are important design considerations. This AFE is intended for compact imaging systems in which a sensor signal must be converted into high-resolution digital data. A 16-bit conversion stage can preserve a large number of gray levels, while operation at 6 MSPS supports line-based sensor readout and other sequential imaging workflows. The 3.3 V supply requirement simplifies integration with contemporary low-voltage digital processors, provided that the complete signal chain meets the interface voltage requirements of the selected sensor and processor. Typical applications include document scanners, flatbed scanners, inspection equipment, machine-vision modules, barcode and imaging systems, and other CIS or CCD camera electronics. The same conversion architecture can support a custom sensor interface when its timing, input level, channel requirements, and digital output protocol are compatible with the WM8253SCDS/RV. For new designs, confirm the sensor output waveform, required sampling rate, channel count, clocking scheme, voltage rails, and output interface against the manufacturer datasheet before assigning the PCB footprint. Because the WM8253SCDS/RV is a single-channel device, a multi-channel imaging system may require multiple AFEs or a different converter architecture. This product page combines the documented WM8253SCDS/RV specifications with package, sourcing, replacement, and application guidance. It also identifies the only verified direct replacement candidate so that engineers can distinguish true pin-compatible interchange from unrelated sensor-interface ICs.

Permintaan RFG Kontak
WM8253SCDS/V - 16-Bit 6 MSPS CIS/CCD AFE | Cirrus Logic
WM8253SCDS/V

WM8253SCDS/V - 16-Bit 6 MSPS CIS/CCD AFE | Cirrus Logic

Cirrus Logic WM8253SCDS/V is a single-channel, 16-bit analog front end designed for CIS and CCD imaging systems. It operates at 3.3 V, supports conversion at 6 MSPS, provides a 4-bit wide output, and is packaged in a 20-pin SSOP. The listed power consumption is 132 mW, making the device suitable for compact imaging equipment where channel count, interface width, and power must be balanced. An analog front end, or AFE, is the signal-conditioning and conversion section between an imaging sensor and the subsequent digital processing system. Its functional hierarchy is AFE → analog signal conditioner → ADC/ADC front end → semiconductor. In a CIS or CCD camera, the AFE conditions the sensor output and converts the resulting analog waveform into digital data. The WM8253SCDS/V combines a one-channel, 16-bit conversion path with the processing features needed for video-oriented imaging applications. The device’s headline characteristics are its 16-bit conversion resolution, 6 MSPS operating rate, and single-channel architecture. The 4-bit wide output provides a compact digital interface between the AFE and downstream logic, while the 20-pin SSOP package supports surface-mount assembly. Its specified 132 mW power consumption is also an important consideration for thermally constrained camera modules and compact embedded imaging systems. The WM8253SCDS/V is positioned for charge-coupled device and CMOS image sensor imaging rather than general-purpose standalone ADC use. A single converter channel makes it appropriate for designs where one sensor output is processed at a time and full multi-channel integration is not required. The 3.3 V operating voltage also places it alongside modern low-voltage digital imaging electronics, allowing the analog and digital portions of a camera design to operate within the same supply framework. Typical applications include compact digital cameras, surveillance-camera imaging channels, industrial vision modules, and embedded CIS-based imaging systems. In these systems, the AFE accepts the sensor signal, performs analog conditioning and digitization, and presents a 4-bit-wide output to the associated image-processing or data-capture circuitry. A 6 MSPS conversion rate supports video-class signal capture, while the 16-bit representation preserves fine numerical detail from the analog stage. Designers should verify the sensor interface requirements against the pin descriptions and recommended application circuit in the manufacturer datasheet before assigning signals. Pay particular attention to supply decoupling, analog grounding, clocking, data-output timing, and the distinction between SSOP pin numbering and the physical lead orientation. The 132 mW listed dissipation should also be checked against the module’s ambient temperature and available copper area. This page organizes the manufacturer datasheet information, exact-MPN pricing evidence, package details, application guidance, and selection considerations into a practical engineering reference. It also distinguishes verified drop-in replacements from alternatives that cannot be confirmed as pin-compatible, helping designers avoid making a replacement decision from incomplete similarity data.

Permintaan RFG Kontak
WM8255SEFL - 16-Bit 12 MSPS Single-Channel CCD/CIS AFE
WM8255SEFL

WM8255SEFL - 16-Bit 12 MSPS Single-Channel CCD/CIS AFE

Cirrus Logic WM8255SEFL is a single-channel 16-bit analog front end and digitizer for CCD and contact image sensor (CIS) imaging systems, processing analog pixel signals at rates up to 12 MSPS. The device is supplied in a 28-QFN 4 x 4 mm package and is identified by distributor listings as a 1-channel AFE with integrated signal processing for image sensors. An analog front end (AFE) is an interface circuit between an imaging sensor and the digital signal-processing system. It conditions the sensor output, removes reset or pedestal-related offsets, applies gain and offset adjustments, performs correlated double sampling where supported, and converts the conditioned analog waveform into digital data. In the broader IC hierarchy, the WM8255SEFL belongs to the ADC/DAC and interface-processing family, specifically the imaging analog front-end category. The WM8255 includes reset-level clamping, correlated double sampling, programmable gain and offset adjustment functions, and a complete signal-processing channel for CCD or CIS signals. Its 16-bit conversion resolution supports precise capture of sensor output levels, while the 12 MSPS pixel sample rate supports demanding scanner, document-imaging, machine-vision, and optical-registration workflows. The single-channel architecture is appropriate where the imaging system does not require simultaneous processing of multiple sensor outputs. The 28-QFN package is designed for compact surface-mount PCB layouts, but the QFN construction requires careful thermal-pad assembly and land-pattern compliance. Signal integrity is central because the device handles small analog sensor signals and clock-related timing paths. Designers should preserve the manufacturer-recommended decoupling, analog and digital grounding, clock routing, and sensor-interface layout patterns described by the WM8255 documentation. Typical uses include CCD-based scanners, CIS scanners, document imaging, industrial inspection, optical measurement, and other embedded imaging products. The part may be considered in new designs when the system specifically requires a CCD/CIS-oriented single-channel AFE and can be matched to its electrical and timing requirements. The manufacturer product page identifies WM8255 as discontinued, so procurement and design decisions should account for lifecycle status rather than assuming long-term availability. Before schematic capture, verify the complete device pinout, supported operating modes, supply requirements, clocking limits, and application-specific sensor interface against the manufacturer documentation. Because public search results provide the main functional and package facts but do not expose every timing, voltage, or environmental parameter, missing values are identified explicitly rather than guessed. This page consolidates the verified WM8255 identification, single-channel CCD/CIS AFE function, 16-bit resolution, 12 MSPS throughput, 28-QFN package, source links, lifecycle notice, and practical design guidance into a procurement-oriented technical summary. It is intended to help engineers locate the datasheet and assess the part before committing to a PCB or production build.

Permintaan RFG Kontak
WM8255SEFL/R - 16-Bit 12 MSPS Single-Channel CCD/CIS AFE (Tape & Reel)
WM8255SEFL/R

WM8255SEFL/R - 16-Bit 12 MSPS Single-Channel CCD/CIS AFE (Tape & Reel)

Cirrus Logic WM8255SEFL/R is a single-channel 16-bit analog front end and digitizer for CCD and contact image sensor (CIS) imaging systems, processing analog pixel signals at rates up to 12 MSPS. The device is supplied in a 28-QFN 4 x 4 mm package and is identified by distributor listings as a 1-channel AFE with integrated signal processing for image sensors. An analog front end (AFE) is an interface circuit between an imaging sensor and the digital signal-processing system. It conditions the sensor output, removes reset or pedestal-related offsets, applies gain and offset adjustments, performs correlated double sampling where supported, and converts the conditioned analog waveform into digital data. In the broader IC hierarchy, the WM8255SEFL/R belongs to the ADC/DAC and interface-processing family, specifically the imaging analog front-end category. The WM8255 includes reset-level clamping, correlated double sampling, programmable gain and offset adjustment functions, and a complete signal-processing channel for CCD or CIS signals. Its 16-bit conversion resolution supports precise capture of sensor output levels, while the 12 MSPS pixel sample rate supports demanding scanner, document-imaging, machine-vision, and optical-registration workflows. The single-channel architecture is appropriate where the imaging system does not require simultaneous processing of multiple sensor outputs. The 28-QFN package is designed for compact surface-mount PCB layouts, but the QFN construction requires careful thermal-pad assembly and land-pattern compliance. Signal integrity is central because the device handles small analog sensor signals and clock-related timing paths. Designers should preserve the manufacturer-recommended decoupling, analog and digital grounding, clock routing, and sensor-interface layout patterns described by the WM8255 documentation. Typical uses include CCD-based scanners, CIS scanners, document imaging, industrial inspection, optical measurement, and other embedded imaging products. The part may be considered in new designs when the system specifically requires a CCD/CIS-oriented single-channel AFE and can be matched to its electrical and timing requirements. The manufacturer product page identifies WM8255 as discontinued, so procurement and design decisions should account for lifecycle status rather than assuming long-term availability. Before schematic capture, verify the complete device pinout, supported operating modes, supply requirements, clocking limits, and application-specific sensor interface against the manufacturer documentation. Because public search results provide the main functional and package facts but do not expose every timing, voltage, or environmental parameter, missing values are identified explicitly rather than guessed. This page consolidates the verified WM8255 identification, single-channel CCD/CIS AFE function, 16-bit resolution, 12 MSPS throughput, 28-QFN package, source links, lifecycle notice, and practical design guidance into a procurement-oriented technical summary. It is intended to help engineers locate the datasheet and assess the part before committing to a PCB or production build.

Permintaan RFG Kontak
WM8259SCDS/RV - 16-Bit 3 MSPS CIS/CCD AFE | Cirrus Logic
WM8259SCDS/RV

WM8259SCDS/RV - 16-Bit 3 MSPS CIS/CCD AFE | Cirrus Logic

The Cirrus Logic WM8259SCDS/RV is a single-channel, 16-bit CIS/CCD analog front end with a 4-bit wide output, 3 MSPS conversion capability, and 132 mW power consumption. It is packaged in a 20-SSOP and is designed for imaging systems that require programmable gain, signal conditioning, and digital conversion from charge-coupled device or CMOS image sensor outputs. An analog front end, or AFE, is an integrated signal-processing block placed between an image sensor and the system digital electronics. In the broader hierarchy, an AFE is an integrated circuit, an interface device, and part of the image-signal-processing chain. The WM8259SCDS/RV combines analog input conditioning with a 16-bit SAR-type conversion function and a digital output interface, reducing the number of separate components required in scanner, camera, and optical measurement equipment. The key features of this device include one analog channel, 16-bit resolution, 3 MSPS operation, a 4-bit-wide output, and 132 mW operation. The wide output is intended to carry the converted digital result efficiently to downstream circuitry. Its single-channel architecture makes it appropriate for systems where one sensor output is processed at a time, while the 3 MSPS rate supports imaging workflows requiring faster sequential sampling than low-speed general-purpose signal converters. The WM8259SCDS/RV is identified as a CMOS image sensor and charge-coupled device AFE. Its architecture is therefore centered on receiving sensor-generated analog information, applying the required gain and signal conditioning, and converting that information into a digital representation. The 16-bit word length provides substantially more numerical resolution than an 8-bit or 12-bit interface, which can be useful when preserving low-level image detail or reducing quantization error in downstream processing. Typical applications include document scanners, imaging modules, machine-vision systems, barcode and inspection equipment, and other CIS or CCD signal-chain designs. In these systems, the device can be positioned after the image sensor and before the image processor, allowing the sensor output to be conditioned and digitized before digital processing begins. The 3 MSPS operating rate supports practical throughput for line-scan and area-scan imaging workflows. PCB implementation should follow the manufacturer datasheet pin description and recommended application circuit. Pay particular attention to analog input routing, decoupling, clocking, and the digital output interface. Because the device combines analog and digital functions, keeping sensitive sensor and reference paths away from high-current switching nodes reduces the risk of coupling unwanted noise into the image signal. This product page combines the WM8259SCDS/RV device description, package information, technical identification, sourcing details, and practical interface guidance. It is intended to help engineers evaluate whether the Cirrus Logic AFE matches their CIS or CCD signal-chain requirements before moving into detailed circuit design.

Permintaan RFG Kontak
WM8259SCDS/V - 16-Bit CCD/CIS AFE | Cirrus Logic
WM8259SCDS/V

WM8259SCDS/V - 16-Bit CCD/CIS AFE | Cirrus Logic

The Cirrus Logic WM8259SCDS/V is a single-channel, 16-bit analog front end for CCD and CMOS image sensors, operating at up to 3 MSPS with 132 mW power consumption in a 20-pin SSOP package. It combines analog image-signal processing with a 3.3 V ADC output stage for compact electronic imaging systems. An analog front end, or AFE, is a semiconductor interface between an imaging sensor and the downstream digital signal-processing or storage system. Its role in the imaging hierarchy is sensor interface, analog signal conditioning, and data conversion. The WM8259SCDS/V belongs to the broader CCD/CIS ADC and ADC/DAC product categories, while the 16-bit ADC and four-bit-wide parallel output implement the digital sampling interface. The device provides two selectable video-input pins and one complete analog processing channel. According to the manufacturer datasheet, that channel includes reset-level clamping, correlated double sampling, programmable gain, and offset adjustment. Internal multiplexers permit rapid switching between offset and gain settings during line-by-line color processing. These functions reduce the amount of external analog conditioning normally required around a CCD or CIS sensor. Its 16-bit conversion resolution and 3 MSPS sampling rate support imaging designs that require more precision than an 8-bit or 12-bit sensor interface. The 132 mW operating-power figure is suitable for compact camera, scanner, and machine-vision systems where signal-chain power can affect thermal design. The 3.3 V supply and four-bit-wide digital output organize the device around contemporary CMOS image-sensor interfaces. Typical applications include CCD-based scanners, CMOS image-sensor modules, color-line imaging systems, surveillance cameras, barcode readers, industrial vision equipment, and embedded imaging controllers. In each case, the selectable inputs, analog clamp, correlated double sampling, gain controls, and offset controls help implement a consistent readout chain close to the image sensor. PCB design should preserve the manufacturer’s recommended input, output, and bypass-capacitor placement because the AFE combines high-speed sampling with sensitive analog processing. Keep sensor traces short, provide a low-impedance return path, and follow the pin-configuration and layout guidance in the datasheet. Verify that downstream logic matches the device’s four-bit-wide output and required clocking arrangement. This product page combines the manufacturer-function description, distributor package and speed information, a verified same-package cross-reference, and practical interface guidance. It is intended to help engineers identify the correct imaging AFE, distinguish the available order code, plan board-level integration, and evaluate where this single-channel 16-bit CCD/CIS front end fits.

Permintaan RFG Kontak
WM8281ECS/R - Low-Power Smart Audio Codec | Cirrus Logic
WM8281ECS/R

WM8281ECS/R - Low-Power Smart Audio Codec | Cirrus Logic

The Cirrus Logic WM8281ECS/R is a low-power smart audio codec with programmable DSP processing, acoustic echo cancellation, and ambient noise cancellation in a 138-W-CSP package measuring 5.86 mm by 4.56 mm. It provides a 24-bit audio interface using SLIMbus and is identified by distributor data as integrating 6 ADC and 8 DAC channels. An audio codec is an integrated circuit that converts analog microphone or line-level signals into digital audio data while converting digital playback streams back into analog audio outputs. The WM8281 belongs to the broader smart-codec hierarchy, combining a conventional audio codec with embedded DSP functions. This integration allows a host processor to handle system control while dedicated hardware executes noise reduction, echo cancellation, speech enhancement, and advanced media processing. Key product features include programmable DSP cores supporting multi-microphone wideband noise reduction, acoustic echo cancellation, speech enhancement, and advanced media enhancement. The 24-bit SLIMbus interface supports connected audio systems, while the integrated ADC and DAC channels reduce the external analog circuitry required for voice and multimedia products. Its low-power design is intended to benefit always-listening and portable audio equipment where continuous processing must remain energy efficient. The WM8281 architecture separates audio conversion from programmable signal processing. SLIMbus provides a shared serial link between the codec and a host or audio processor, while the DSP feature set performs real-time voice enhancement. This combination can shorten signal paths and reduce system complexity in applications requiring microphone capture, voice processing, and audio playback through a common codec package. Typical uses include smartphone and tablet voice-calling systems, headset and wearable audio platforms, smart speakers, teleconferencing equipment, voice-user-interface products, and connected consumer devices. Cirrus Logic markets the device as a low-power smart codec with echo cancellation, making it especially relevant to designs handling near-field or far-field speech where acoustic feedback and ambient noise reduce intelligibility. Designers should treat the 138-ball wafer-level chip-scale package as a layout-intensive component and follow the manufacturer's recommended land pattern, exposed-pad, power, ground, and high-speed routing guidance. The analog and digital power domains, microphone inputs, codec outputs, and SLIMbus signals must be planned together because power sequencing, decoupling, and acoustic layout can materially affect performance. This page consolidates verified manufacturer and distributor information about the WM8281ECS/R, identifies the missing technical fields explicitly, and provides application-focused selection guidance without presenting unverified electrical values, pin assignments, pricing, or drop-in replacements as confirmed facts.

Permintaan RFG Kontak
WM8350GEB/V 12-Bit Audio Codec | Cirrus Logic | Power Management
WM8350GEB/V

WM8350GEB/V 12-Bit Audio Codec | Cirrus Logic | Power Management

Cirrus Logic WM8350GEB/V is a 12-bit stereo audio interface with integrated power management, operating at 48 kHz and supplied in a 129-BGA package measuring 7 x 7 mm. The device combines two ADC and two DAC channels, according to the verified distributor and cross-reference records, making it suitable for compact audio subsystems that need conversion and regulated power support in one package. Its BGA construction supports dense PCB layouts but requires careful ball-layout inspection, assembly-process control, and thermal verification. An audio codec is a mixed-signal semiconductor that converts digital audio samples into analog signals and analog sound signals into digital data. A stereo codec therefore normally handles left and right playback and recording paths. As an integrated circuit combining audio conversion with power management, the WM8350GEB/V belongs to the broader semiconductor and audio-interface hierarchy rather than being a simple analog amplifier or passive audio component. The verified product information identifies the WM8350GEB/V as a 12-bit audio interface operating at 48 kHz. Its 129-BGA, 7 x 7 mm package is a principal selection constraint because pin-compatible alternatives must reproduce the same ball layout, exposed features, and board-level connectivity. The listed package also requires land-pattern and assembly inspection that cannot be completed from a distributor category listing alone. Detailed electrical limits, clock requirements, analog performance, power-rail values, and ball functions must be confirmed in the manufacturer datasheet before schematic or PCB release. The integrated power-management function can simplify the architecture of portable and embedded audio products by placing conversion and rail support in one device. This integration may reduce the number of external supporting components when the application uses the complete WM8350 audio subsystem. The tradeoff is that its 129-ball package is less straightforward to hand-solder and more dependent on advanced assembly capability than a leaded or small-outline package. Designers should also validate startup sequencing, analog grounding, clocking, and codec-to-host interface timing against the intended system architecture. Typical uses include portable media devices, smart displays, connected audio products, communication terminals, and embedded systems requiring stereo recording and playback. In these applications, the 48 kHz sampling rate supports conventional digital-audio workflows, while the 12-bit resolution defines the converter word length represented by the verified listing. System-level audio quality still depends on microphone conditioning, amplifier selection, clock jitter, analog layout, grounding, and power-supply implementation; the codec alone does not determine the final acoustic performance. Before design-in, engineers should obtain the official WM8350 datasheet and verify the complete 129-ball pin map, recommended decoupling, supported clock modes, host interface, analog input and output limits, and absolute maximum ratings. The verified distributor record labels the part as an audio interface and 12-bit codec, but it does not provide those implementation details. PCB designers should use the manufacturer land pattern rather than deriving it from package dimensions, and assemblers should confirm whether the selected BGA assembly process supports the device's ball pitch and thermal requirements. This page consolidates verified distributor identification, package constraints, cross-reference evidence, procurement questions, and application guidance that a basic catalog result does not provide. It also distinguishes verified facts from parameters requiring datasheet confirmation, helping engineers decide whether the WM8350GEB/V fits their PCB before committing to a 129-BGA design.

Permintaan RFG Kontak
WM8351CGEB/V - Stereo Audio Codec with Power Management | Cirrus Logic
WM8351CGEB/V

WM8351CGEB/V - Stereo Audio Codec with Power Management | Cirrus Logic

The Cirrus Logic WM8351CGEB/V is a stereo audio codec with integrated power management, featuring two ADCs, two DACs, 24-bit resolution, and support for 48 kHz audio in a 129-pin FBGA package. It combines audio conversion and power-management functions in one component, reducing the number of separate devices required in portable and connected audio systems. An audio codec is a mixed-signal semiconductor that converts between digital audio data and analog microphone or headphone signals. In the hierarchy of electronic components, the WM8351CGEB/V is an audio codec within the broader categories of ADC/DAC converter, interface IC, and power management IC. Its integrated power-management block places it in the same device family as the company’s AudioPlus stereo codec products. The device provides two ADC channels, two DAC channels, 24-bit conversion resolution, and a maximum identified sampling rate of 48 kHz. These attributes suit applications requiring full-duplex stereo audio paths, such as telephony, communication endpoints, portable media equipment, and embedded audio systems. The integrated power-management section is intended to simplify system partitioning around the codec and its associated analog rails. The 129-pin FBGA package supports a dense, mixed-signal layout with separate analog, digital, and power-related connections. Because the package contains numerous pins and the board-level design depends on precise routing, the manufacturer pin-description table and reference layout should be used directly when allocating PCB tracks. The BGA construction also makes inspection and assembly-process planning essential during production. Typical applications include two-way communication terminals, audio-equipped embedded controllers, smart-home endpoints, and portable listening devices. For designs requiring additional output channels, the PCM5122PWR digital-to-analog converter can serve as a companion when supported by the host audio architecture, while TAS5709PHPR and TAS5715PHPR provide class-D amplification when the system specification requires that function. When designing the power architecture, treat the integrated power-management section as part of a carefully sequenced analog and digital supply network. Verify startup order, rail limits, decoupling requirements, and the exposed-pad connection against the manufacturer documentation. Because the BGA package has a large pin count and limited escape options, impedance-controlled routing and thermal via placement should be planned before schematic sign-off. This page organizes the WM8351CGEB/V conversion, package, and application characteristics into an engineering-focused reference, adds application-specific design guidance, and identifies the limits of drop-in replacement qualification. It supports component selection, schematic review, and PCB planning without replacing the manufacturer’s complete electrical and pinout documentation.

Permintaan RFG Kontak
WM8501CGED - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic
WM8501CGED

WM8501CGED - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic

The Cirrus Logic WM8501CGED is a 24-bit stereo digital-to-analog converter with a 192kHz sampling rate, DSP and I2S data interfaces, and a 14-SOIC package. It includes a 1.7Vrms line driver according to the Wolfson datasheet listing. The device is intended for high-fidelity audio playback and digital audio conversion. Its two-channel architecture supports stereo output, while the 24-bit word length and 192kHz sampling capability target high-resolution audio systems. An audio DAC is a data-conversion IC that transforms digital audio samples into analog voltage signals. In the signal chain, a digital source such as a decoder, computer, CD player, or streaming interface supplies samples to the DAC, which then drives an audio amplifier, headphones, mixer, or line input. The WM8501CGED belongs to the ADC/DAC and data-conversion IC hierarchy, specifically the special-purpose audio DAC class. The verified specifications identify a stereo DAC, 24-bit resolution, 192kHz operation, DSP and I2S interfaces, analog and digital supply sources, a 2.7V to 5.5V supply range, and a -40°C to 85°C operating-temperature range. The 1.7Vrms line driver is the key analog-output feature listed by the datasheet source. The 14-SOIC package supports conventional surface-mount PCB assembly while exposing the digital control, power, and analog connections required by the converter. Because the available verified data does not include the complete electrical timing table, pin names, pinout drawing, digital input logic levels, output distortion, dynamic range, channel separation, or recommended application circuit values, those parameters are marked as data needed rather than inferred. The 24-bit and 192kHz ratings should be treated as interface and format capabilities, not as a guarantee of end-to-end audio performance without checking the complete manufacturer documentation and analog implementation. Typical application domains include consumer audio equipment, compact digital audio systems, powered speakers, sound-bar signal paths, computer audio accessories, and legacy high-resolution playback designs. The I2S interface can connect to a suitable digital audio controller when its clocking and framing requirements match the WM8501CGED. The DSP interface provides an additional digital control path for supported audio-processing configurations, but software and register compatibility must be verified before replacement. The main design consideration is power and signal integrity. Keep the analog and digital supplies properly decoupled, route high-frequency digital clocks away from the analog output, and follow the manufacturer’s recommended land pattern and component placement when those details are available. This page combines the verified distributor classification, package and interface information, datasheet-link sources, and engineering selection guidance without adding unverified performance claims.

Permintaan RFG Kontak
WM8501CGED/R - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic (Tape & Reel)
WM8501CGED/R

WM8501CGED/R - 24-Bit 192kHz Stereo Audio DAC | Cirrus Logic (Tape & Reel)

The Cirrus Logic WM8501CGED/R is a 24-bit stereo digital-to-analog converter with a 192kHz sampling rate, DSP and I2S data interfaces, and a 14-SOIC package. It includes a 1.7Vrms line driver according to the Wolfson datasheet listing. The device is intended for high-fidelity audio playback and digital audio conversion. Its two-channel architecture supports stereo output, while the 24-bit word length and 192kHz sampling capability target high-resolution audio systems. An audio DAC is a data-conversion IC that transforms digital audio samples into analog voltage signals. In the signal chain, a digital source such as a decoder, computer, CD player, or streaming interface supplies samples to the DAC, which then drives an audio amplifier, headphones, mixer, or line input. The WM8501CGED/R belongs to the ADC/DAC and data-conversion IC hierarchy, specifically the special-purpose audio DAC class. The verified specifications identify a stereo DAC, 24-bit resolution, 192kHz operation, DSP and I2S interfaces, analog and digital supply sources, a 2.7V to 5.5V supply range, and a -40°C to 85°C operating-temperature range. The 1.7Vrms line driver is the key analog-output feature listed by the datasheet source. The 14-SOIC package supports conventional surface-mount PCB assembly while exposing the digital control, power, and analog connections required by the converter. Because the available verified data does not include the complete electrical timing table, pin names, pinout drawing, digital input logic levels, output distortion, dynamic range, channel separation, or recommended application circuit values, those parameters are marked as data needed rather than inferred. The 24-bit and 192kHz ratings should be treated as interface and format capabilities, not as a guarantee of end-to-end audio performance without checking the complete manufacturer documentation and analog implementation. Typical application domains include consumer audio equipment, compact digital audio systems, powered speakers, sound-bar signal paths, computer audio accessories, and legacy high-resolution playback designs. The I2S interface can connect to a suitable digital audio controller when its clocking and framing requirements match the WM8501CGED/R. The DSP interface provides an additional digital control path for supported audio-processing configurations, but software and register compatibility must be verified before replacement. The main design consideration is power and signal integrity. Keep the analog and digital supplies properly decoupled, route high-frequency digital clocks away from the analog output, and follow the manufacturer’s recommended land pattern and component placement when those details are available. This page combines the verified distributor classification, package and interface information, datasheet-link sources, and engineering selection guidance without adding unverified performance claims.

Permintaan RFG Kontak
WM8510GEDS/RV - Mono 24-Bit Audio Codec | Cirrus Logic
WM8510GEDS/RV

WM8510GEDS/RV - Mono 24-Bit Audio Codec | Cirrus Logic

The Cirrus Logic WM8510GEDS/RV is a mono audio codec with an integrated speaker driver, a 24-bit serial audio interface, and a 28-pin SSOP package. The device operates from a 2.5 V to 3.6 V supply and is intended for space-constrained consumer audio systems requiring digital-to-analog conversion and direct speaker output. Its operating temperature range is -40 °C to +85 °C, and the /RV ordering code identifies the specified surface-mount package variant. An audio codec is an interface IC that converts digital audio data into an analog output and, where supported, manages the electrical interface to an audio transducer. The WM8510 belongs to the broader codec, audio interface, signal-conversion, and semiconductor hierarchy. Integrating a mono codec and speaker driver into one package reduces the component count in portable equipment while keeping the analog output path close to the digital audio source. The WM8510GEDS/RV provides a 24-bit serial audio path, mono signal processing, and an integrated speaker-driver function in a 28-SSOP package. Its 2.5 V to 3.6 V supply range is suitable for low-voltage portable systems, while its surface-mount SSOP construction supports automated assembly. The manufacturer identifies the part as RoHS compliant, supporting use in modern electronics manufacturing where restricted-substance requirements apply to the bill of materials. The codec uses a sigma-delta architecture, a design commonly used to implement high-resolution audio conversion with integrated digital filtering. Serial audio data is transferred through a compact digital interface before being converted for the analog audio output. The integrated speaker driver allows the device to serve as the central audio-output block in products where a dedicated external speaker amplifier would add cost, board area, or complexity. Exact clock, conversion-rate, output-level, and speaker-load limits should be confirmed in the manufacturer datasheet before final circuit design. Typical applications include portable media players, personal audio equipment, compact consumer appliances, voice-accessory systems, and other products with a mono audio-speaker requirement. Its 28-pin SSOP package is especially relevant where the available PCB area is limited but a through-hole solution would be undesirable. The -40 °C to +85 °C range covers industrial-temperature consumer and embedded product environments when all associated system requirements are met. Designers should confirm the supported sample rate, master-clock requirement, digital audio format, speaker impedance, power-supply sequencing, and decoupling network against the manufacturer datasheet. PCB layout should keep analog output and speaker-driver connections away from digital clock and data traces, while preserving a direct ground-return path from the device to its supply system. This page combines package, interface, environmental, and application details with replacement guidance and practical design considerations.

Permintaan RFG Kontak