Produk (46.000+)

MAX153EWP+ - 8-Bit 1Msps ADC with Power-Down | Maxim
MAX153EWP+

MAX153EWP+ - 8-Bit 1Msps ADC with Power-Down | Maxim

Analog Devices MAX153EWP+ is a microprocessor-compatible, 8-bit flash analog-to-digital converter with a 1 Msps conversion rate, a 660 ns conversion time, and 1 µA power-down capability in a 20-pin SOIC package. It accepts unipolar or bipolar analog inputs and operates from a single +5 V supply or dual ±5 V supplies. A flash ADC is a sampling data-conversion device that uses parallel internal comparators to convert an analog voltage into a digital code. The MAX153 belongs to the ADC hierarchy within data-converter and signal-processing semiconductors. Its microprocessor-compatible interface supports systems in which a processor reads eight digital output bits and controls acquisition through mode and read/write signals. The principal specifications are an 8-bit resolution and a 1 Msps sampling rate. These characteristics make the converter suitable for high-speed control loops, industrial monitoring, data acquisition, and embedded signal measurement. The half-flash architecture provides the 660 ns conversion time cited in the manufacturer datasheet, while the POWERDN control reduces supply consumption to 1 µA when conversion activity is not required. The MAX153 accepts either unipolar or bipolar input ranges and supports single +5 V or dual ±5 V operation. This supply flexibility lets the same converter support multiple analog-system architectures. The device also includes a 4-bit internal flash DAC associated with the reference and conversion circuitry, supporting reference and offset-oriented system arrangements described by the manufacturer. Typical uses include industrial process monitoring, digital voltmeter and panel-meter front ends, microprocessor-controlled instrumentation, and compact embedded measurement systems. Designers can use the 1 Msps throughput for fast-changing signals, while the 8-bit resolution suits quantization and supervisory control tasks where fine analog accuracy is not the primary requirement. Circuit design should account for input settling, reference stability, supply bypassing, and the required read/write timing. Because this is a high-speed flash converter, source impedance and PCB trace length can affect the time available for the internal sampling network to acquire the input. Use the pin-description and timing diagrams in the manufacturer datasheet when assigning control signals and laying out the analog input path. This product page organizes the MAX153EWP+ electrical characteristics, package information, application guidance, and confirmed drop-in alternatives. It also highlights the distinctions that matter during PCB reuse, including operating-temperature grade and package type, so engineers can verify mechanical and electrical compatibility before approving a replacement.

Permintaan RFG Kontak
MAX154AEWG - 8-Bit 4Ch 2.5us ADC w/ Reference | Maxim Integrated
MAX154AEWG

MAX154AEWG - 8-Bit 4Ch 2.5us ADC w/ Reference | Maxim Integrated

The Maxim Integrated (now Analog Devices) MAX154AEWG is a CMOS high-speed 8-bit analog-to-digital converter (ADC) with four analog input channels, an internal 2.5V reference, and track/hold, housed in a 24-pin wide-body SOIC (SO-24W) package. It delivers a 2.5 us conversion time per channel using a successive-approximation register (SAR) architecture, with the MAX154AEWG/A grade rated for -40 C to +85 C industrial operation. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples a continuous analog voltage and converts it into a discrete digital code, typically N-bit binary. SAR ADCs use a binary-search successive-approximation algorithm with an internal DAC and comparator, achieving an excellent balance of speed, resolution, and power consumption for data acquisition, instrumentation, and process-control applications. The MAX154 family sits in the hierarchy: SAR ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor. Key features include four single-ended analog inputs (the pin-compatible MAX158 offers eight), a 2.5V internal bandgap reference (5 V external reference also accepted), ratiometric operation, and an on-chip track/hold. The MAX154AEWG provides 1/2 LSB integral nonlinearity and ±1 LSB total unadjusted error, with low-power CMOS design drawing only a few mW during continuous conversion. The MAX154AEWG uses a standard SAR architecture with internal clock generation, allowing simple microprocessor interface through standard CS, RD, and WR control lines. It connects directly to most 8-bit parallel buses without external glue logic. The wide input voltage range (single +5 V supply) and ratiometric capability make it suitable for both absolute and proportional measurements. Typical applications include data acquisition systems, process control, digital signal processing front-ends, multiplexed sensor monitoring, and portable instruments. The four-channel input makes it ideal for low-channel-count multi-signal monitoring without an external MUX. When designing with this device, observe the recommended 0.1 uF decoupling capacitor on VDD, keep analog and digital ground planes separated, and ensure analog inputs stay within the specified input range (0 V to VREF or 0 V to 5 V). This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found on the manufacturer datasheet, giving engineers a single reference for sourcing, comparison, and design-in.

Permintaan RFG Kontak
MAX154BCAG+T - 8-Bit 4Ch 400ksps 5V Precision ADC | Maxim
MAX154BCAG+T

MAX154BCAG+T - 8-Bit 4Ch 400ksps 5V Precision ADC | Maxim

The Maxim MAX154BCAG+T is a CMOS 8-bit, 4-channel, 400 ksps analog-to-digital converter (ADC) with an integrated 2.5 V on-chip reference, housed in a 24-pin SSOP (CAG) package. According to the Maxim MAX154/MAX158 datasheet, this multi-channel ADC features a 2.5 us conversion time, four analog input channels (the MAX158 has eight), and a complete data-acquisition system on chip including track/hold, reference, and three-state output buffers. The B grade (MAX154B) provides +/-1 LSB INL over the commercial 0C to 70C operating range, while the +T suffix indicates Tape & Reel packaging for high-volume assembly. An ADC (Analog-to-Digital Converter) is a data-acquisition IC that translates continuous analog voltages into discrete digital codes, sitting at the boundary between the analog sensor domain and the digital processor domain within the broader signal chain hierarchy of sensor -> analog front end -> ADC -> microcontroller/DSP. The MAX154BCAG+T belongs to the successive-approximation register (SAR) ADC family, the dominant topology for medium-speed, medium-resolution applications up to a few MSPS where deterministic latency and low power consumption matter more than the raw throughput of pipeline ADCs. Its on-chip 2.5 V reference removes the need for an external precision reference IC, simplifying the BOM for cost-sensitive multi-channel systems. Key features include four single-ended analog inputs with software-configurable channel selection, a 2.5 us successive-approximation conversion engine, on-chip 2.5 V reference (and optional external reference mode), three-state digital outputs for direct microprocessor bus interface, single +5 V supply operation with low CMOS power dissipation, and a half-LSB quantization step of 9.8 mV when using the internal 2.5 V reference across the 0 V to 5 V input span. The internal reference also sources up to 5 mA external current, useful for biasing external signal-conditioning circuitry. The MAX154 architecture pairs a capacitive-DAC SAR core with an input track-and-hold and a low-drift buried-zener reference, achieving the +/-1 LSB integral nonlinearity specified for the B grade and providing a complete data-acquisition subsystem in a single IC. The four input channels share a single ADC core through an internal analog multiplexer, reducing silicon cost relative to per-channel dedicated converters at the expense of throughput during sequential channel scans. Typical applications include data-acquisition front ends for industrial process-control PLCs, multi-slot rack-mounted instrumentation, supervisory distribution and data-logging systems, embedded control boards monitoring temperature/pressure/flow sensors, and portable or rack-mount medical-instrument signal chains. The wide supply tolerance and integrated reference also make it attractive for low-cost microcontroller-based measurement nodes. When designing with this ADC, place the 0.1 uF + 10 uF supply bypass capacitors as close as possible to the +VDD and DGND pins to prevent digital noise from coupling into the analog comparator. Use AGND and DGND star-grounding at the IC reference pin, and verify that the source impedance seen at AIN pins stays below 2.5 kohm to keep track-and-hold settling errors below 0.5 LSB at 400 ksps. This page synthesizes distributor pricing, drop-in alternatives from the Maxim MAX154/MAX158 family, and practical design notes not collected in the manufacturer datasheet.

Permintaan RFG Kontak
MAX154BCWG - 8-Bit 400ksps 4-Ch ADC with Reference | Maxim
MAX154BCWG

MAX154BCWG - 8-Bit 400ksps 4-Ch ADC with Reference | Maxim

The Maxim Integrated MAX154BCWG is a CMOS 8-bit analog-to-digital converter with 4 analog input channels, an internal 2.5V reference, and a track-and-hold amplifier, housed in a 24-pin SOIC wide-body package with conversion time of approximately 2.5 us per channel via successive-approximation register (SAR) architecture at up to 400 ksps aggregate throughput. What is an ADC? An ADC (Analog-to-Digital Converter) is a data-converter IC that samples continuous analog voltage signals and translates them into discrete binary codes for digital processing. Within the data-converter hierarchy, the MAX154 sits in the SAR branch (low-latency, deterministic-conversion) rather than the delta-sigma or pipeline branches. The MAX154 family (MAX154 4-channel, MAX158 8-channel) is part of Maxim's multi-channel 8-bit ADC portfolio introduced in the late 1980s and remains in production for legacy industrial and instrumentation designs. Key features include four single-ended analog inputs with on-chip channel selection (user-controlled via address latches), an internal 2.5V bandgap reference (10 ppm/°C typical drift), wide ±5V analog input range accepting bipolar signals, and an on-chip clock that simplifies external interfaces. The 24-pin SOIC wide-body package provides ample thermal headroom for industrial environments from 0°C to +70°C (C-grade). Typical applications include multi-channel data-acquisition systems, process-control instrumentation, battery-powered portable test gear, digital panel meters, and embedded industrial-control I/O modules where several sensor signals must be digitized with a single ADC. Compared with modern 12/14/16-bit SAR ADCs, the 8-bit MAX154 trades resolution for very high sample rate and small channel-count BOM cost. Design consideration: place the MAX154 close to the analog signal source to minimize trace noise, use a 0.1 uF ceramic bypass capacitor at VDD with a 10 uF bulk cap, and buffer the analog inputs with op-amps when the source impedance exceeds 5 kohm. The internal reference can be overdriven by an external reference for applications needing tighter absolute accuracy. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the Maxim datasheet alone.

Permintaan RFG Kontak
MAX155ACPI+ - 8-Ch 8-Bit 250ksps ADC w/ Simultaneous T/H | Maxim
MAX155ACPI+

MAX155ACPI+ - 8-Ch 8-Bit 250ksps ADC w/ Simultaneous T/H | Maxim

The Maxim Integrated (Analog Devices) MAX155ACPI+ is an 8-bit, 250 ksps, 8-channel successive-approximation analog-to-digital converter (ADC) with simultaneous track-and-hold stages and an internal 2.5 V reference, housed in a 28-pin PDIP (300 mil) through-hole package. It integrates eight sample-and-hold amplifiers so that all input channels are sampled at the same instant, eliminating channel-to-channel timing skew in multiplexed data-acquisition systems. When operating from a single +5 V supply, the MAX155ACPI+ supports both unipolar and bipolar conversions in single-ended or differential input configurations, with 4 or 8 input channels selectable via software. The device features power-down capability for low-power standby between conversions, an internal +2.5 V reference, and a parallel data interface for high-throughput microprocessor connections. According to the manufacturer datasheet, the MAX155 provides a complete sampling data-acquisition system on a single chip, making it suitable for multi-sensor measurement systems where timing alignment is critical. A successive-approximation register (SAR) ADC is a type of analog-to-digital converter that uses a binary search algorithm to resolve an analog input voltage into a digital code, one bit per clock cycle. SAR ADCs are characterized by low latency (no pipeline delay), deterministic conversion time, and excellent DC accuracy, making them well-suited for multiplexed multi-channel systems, precision DC metering, industrial process control, and data-acquisition front-ends. The MAX155's simultaneous sampling T/Hs set it apart from a generic 8-channel SAR: by capturing all eight inputs at the same moment, downstream digital processing can compute true per-sample differential measurements across the array. Key features include 250 ksps aggregate throughput (with simultaneous sampling across all channels), an internal 2.5 V reference with low drift, software-selectable 4-/8-channel operation, single +5 V supply operation, on-chip T/H per channel, parallel microprocessor interface, and a hardware power-down pin that reduces supply current between conversions. The wide input range supports both single-ended (0-VREF) and true bipolar (±VREF) signals. The MAX155 is built on a BiCMOS process that combines low-noise bipolar analog front-ends with CMOS logic for low power dissipation. Internal clock generation and a self-calibrating architecture minimize external component count, while the parallel interface allows direct connection to microprocessors and FPGAs for high-speed system integration. Typical applications include multi-channel instrumentation and data-acquisition systems, vibration and modal analysis, motor control feedback loops, multichannel process control, medical monitoring front-ends, and any system where multiple analog signals must be sampled simultaneously for time-coherent analysis. When designing with the MAX155ACPI+, ensure the analog input source impedance stays below the value specified in the datasheet to maintain acquisition accuracy. Decouple VDD and AVDR with 10uF tantalum and 0.1uF ceramic capacitors placed close to the pins, and keep analog and digital grounds tied to a single star point to minimize crosstalk. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-brand comparison and pinout reference.

Permintaan RFG Kontak
MAX155AEWI - 8-Ch 8-Bit ADC Simultaneous T/H +2.5V Ref
MAX155AEWI

MAX155AEWI - 8-Ch 8-Bit ADC Simultaneous T/H +2.5V Ref

The Analog Devices (formerly Maxim Integrated) MAX155AEWI is a high-speed, 8-channel, 8-bit analog-to-digital converter that integrates simultaneous track-and-hold amplifiers, a precision +2.5 V internal reference, and a parallel interface in a 28-pin wide SOIC package. It performs successive-approximation conversions at throughput up to 250 ksps and supports unipolar/bipolar, single-ended/differential input modes from a single +5 V supply. An ADC (analog-to-digital converter) converts continuous analog signals into discrete digital codes, sitting between analog front-ends and digital processing blocks in any data-acquisition system. A successive-approximation register (SAR) ADC, the architecture used in the MAX155, performs bit-by-bit decisions against a reference in a single conversion clock cycle, trading high speed for moderate resolution. ADCs are a sub-category of data converters within the broader mixed-signal semiconductor family; the MAX155 adds simultaneous track-and-hold, an important innovation that lets up to 8 inputs be sampled within a few hundred nanoseconds of each other - critical for phase-coherent multichannel measurements where channel-to-channel skew would otherwise corrupt the result. Key features include eight single-ended or four differential analog input channels, software-configurable unipolar/bipolar ranges, a +2.5 V internal bandgap reference (with optional external reference input), a throughput rate of 250 ksps with 6 microsecond conversion time, and power-down control that drops supply current to under 50 microamps for battery-sparing designs. The MAX155AEWI variant is specified for the -40 °C to +85 °C extended industrial temperature range and is offered in a wide-body 28-SOIC package for robust surface-mount assembly. Inside the device, eight input track-and-hold blocks feed a single shared SAR core and DAC reference ladder; the +2.5 V reference is buffered and brought out to a pin for use by external sensor bridges or ratiometric networks, eliminating a separate reference IC. The parallel interface separates conversion control (WR) from data retrieval (RD), and the channel configuration RAM is addressable through a shared 8-bit bus - this dual mode was a common Maxim innovation in early 1990s data-acquisition parts and is still quoted in modern designs as a clean way to multiplex a single bus. Typical applications include multi-channel data-acquisition front-ends in industrial process instrumentation, sensor array digitizers where simultaneous sampling is required (load-cell weigh scales, vibration monitoring, multi-phase power metering), portable instrumentation powered from +5 V rails, and embedded digital-control loops. The wide SOIC package, single-supply operation, and integrated reference make the part especially attractive for space-constrained designs that need many sampled channels. When using the MAX155AEWI, ensure that the analog inputs remain within the common-mode range of the track-and-hold amplifiers (typically VDD - 1.5 V to GND) and that decoupling includes a 10 microfarad bulk capacitor plus a 0.1 microfarad ceramic close to each supply pin. Because the +2.5 V reference is brought out to a pin, it must be buffered with an op-amp if used to drive low-impedance loads. This page consolidates distributor pricing, drop-in alternatives such as MAX155AEWI+, MAX155ACWI, MAX155BEWI and MAX155BCWI, plus practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX155BEPI+ - 8-Channel 8-Bit 250ksps SAR ADC | Maxim Integrated
MAX155BEPI+

MAX155BEPI+ - 8-Channel 8-Bit 250ksps SAR ADC | Maxim Integrated

The Maxim Integrated MAX155BEPI+ (now supplied by Analog Devices) is a high-speed, 8-bit, multi-channel successive-approximation analog-to-digital converter (SAR ADC) with 4 or 8 single-ended/differential analog input channels, integrated simultaneous track-and-hold amplifiers, and an internal 2.5V reference, packaged in a 28-pin plastic DIP (PDIP-28) through-hole package. It delivers sampling rates up to 250 ksps and is qualified for the -40C to +85C industrial temperature range, with the "B" speed grade distinguishing it from the slower "A" grade (the "EPI" suffix denotes the industrial temp PDIP package). A SAR ADC is a type of analog-to-digital converter that converts an analog input into a digital code using a binary-search successive-approximation register. SAR ADCs sit in the broader hierarchy: ADC -> data converter -> mixed-signal IC -> integrated circuit. They are favored over delta-sigma and pipeline ADCs when the application needs low latency, deterministic acquisition time, and moderate-to-high sampling rates without pipeline delay, making them common in industrial multiplexing, motor control, and instrumentation loops. The key differentiating features of the MAX155 are its eight simultaneous track/hold amplifiers (one per channel) that eliminate channel-to-channel sampling skew, the internal precision 2.5V reference (saving board space and BOM cost), and a flexible parallel data interface compatible with most microcontrollers and DSPs. Each input channel can be configured as single-ended or differential, and an analog multiplexer under software control selects which channel the SAR core digitizes while all eight T/Hs sample at the same instant. Architecturally, the device combines an 8:1 input MUX, eight dedicated sample-and-hold capacitors, a single shared SAR core, an internal reference buffer, and a parallel output register. This "MUX + simultaneous T/H" topology trades simultaneous-snapshot timing accuracy (typically <50 ns channel-to-channel skew) for the throughput ceiling of one ADC core. The "B" grade offers the fastest conversion time in the MAX155 family. Typical applications for the MAX155BEPI+ include industrial process control data acquisition boards, multi-axis motor position feedback, multiplexed thermocouple or strain-gauge signal chains, simultaneous-sampling vibration/acoustic analyzers, and embedded instrumentation front-ends. The DIP-28 package is friendly to breadboard prototyping, legacy through-hole designs, and educational lab work where surface-mount packages are inconvenient. When designing with this part, ensure the analog inputs remain within the supply rails (typically +/-5V or 0-5V with VDD=+5V, VSS=-5V) and add a 10 nF ceramic bypass on the reference pin to maintain low-noise conversions. Because the part is now in Last Time Buy status per distributor listings, consider the MAX155BEWI+ (SOIC-28) or other drop-in-compatible ADC alternatives listed below for new production runs. This page synthesizes distributor pricing, drop-in compatible 8-channel SAR ADC alternatives, and practical layout/design notes not aggregated in the manufacturer datasheet alone.

Permintaan RFG Kontak
MAX156BCNG - 8-Ch 8-Bit 250ksps ADC w/ T/H | Maxim Integrated
MAX156BCNG

MAX156BCNG - 8-Ch 8-Bit 250ksps ADC w/ T/H | Maxim Integrated

The Maxim Integrated MAX156BCNG is an 8-bit, 8-channel successive-approximation analog-to-digital converter (ADC) with simultaneous track-and-hold amplifiers and an internal 2.5V reference, sampling at up to 250 ksps in a 24-pin PDIP through-hole package. It integrates two or four input channels (selectable via software) with dual simultaneous sample-and-hold stages that capture two analog signals at exactly the same instant, eliminating inter-channel skew in vector measurements. The device operates from a single +5V analog supply plus a digital 5V supply and features a parallel microprocessor interface for fast data transfer. A successive-approximation ADC is a type of data converter that resolves each conversion one bit at a time using an internal binary-search algorithm, offering a favorable trade-off between speed, resolution, and die size compared to flash or sigma-delta architectures. SAR ADCs sit in the hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. The MAX156's 8-bit resolution and 250 ksps throughput place it in the mid-speed data-acquisition tier used for instrumentation, video digitizing, and DSP front-ends where 8-bit dynamic range is acceptable. Key features include 8 input channels (software-configurable as 2 or 4 single-ended inputs or differential pairs), simultaneous track-and-hold for paired channels, internal +2.5V reference with external override option, single +5V analog supply plus digital 5V supply, and a parallel interface compatible with most microprocessors. The device guarantees no missing codes over the full operating temperature range and provides ±1 LSB linearity. Typical applications include multichannel data-acquisition systems, simultaneous-sampling instrumentation, DSP front-end analog input stages, industrial process control with multiple sensors, and portable or benchtop test equipment. The internal reference simplifies BOM and layout while keeping the device suitable for cost-sensitive multi-channel designs.

Permintaan RFG Kontak
MAX156BENG - 8-Ch 8-Bit 250ksps ADC with T/H | Maxim Integrated
MAX156BENG

MAX156BENG - 8-Ch 8-Bit 250ksps ADC with T/H | Maxim Integrated

The Maxim Integrated MAX156BENG is a high-speed, 8-channel, 8-bit analog-to-digital converter with simultaneous track-and-hold amplifiers and an internal 2.5V reference, housed in a 24-pin PDIP (DIP-24) through-hole package. It supports throughput up to 250 ksps per channel (278 ksamples/sec aggregate sample rate is reported by some distributor sources) and operates from a single 4.75V to 5.25V analog supply with low 2.7 mA operating current. The MAX156BENG targets multiplexed data-acquisition front-ends where simultaneous sampling of multiple analog inputs is required. A successive-approximation ADC (SAR ADC) is a type of analog-to-digital converter that resolves one bit per clock cycle using a binary search across an internal DAC and comparator, achieving a deterministic conversion time and low latency. The simultaneous track-and-hold front-end on every channel captures all inputs at exactly the same instant, preserving phase relationships between channels - critical for multi-phase power, vibration analysis, and motor-control feedback. This places the MAX156 in the data converter hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Key features include 8 single-ended analog input channels, an internal 2.5V reference, input range of 0V to +2.5V unipolar or ±2.5V bipolar (with external reference and signal conditioning), and software-configurable unipolar/bipolar operation per the device datasheet. The +2.5V reference output can drive external circuitry. The MAX156BENG is the through-hole commercial-temperature variant (0C to +70C); the MAX156BENG+ suffix denotes the industrial-grade (-40C to +85C) version. The 24-pin PDIP footprint supports breadboard-friendly prototyping and easy hand-solder rework. Architecture: an input multiplexer feeds eight track-and-hold amplifiers whose outputs connect to a single SAR core with an integrated reference. Conversion control is via a standard microprocessor-compatible parallel interface with read, convert, and chip-select signals. The device dissipates approximately 13.5 mW at 5V/250 ksps and powers down between conversions for battery-friendly operation. Typical applications include multi-channel data acquisition systems, industrial process control, vibration and modal analysis, motor control phase-current sampling, portable instrumentation, and automated test equipment front-ends. The 250 ksps/channel rate comfortably digitizes audio-bandwidth signals from 8 sensors simultaneously. Design considerations: place 0.1uF bypass capacitors close to VDD and VSS pins; route analog and digital grounds as separate planes tied at a single point near the ADC. The internal reference requires an external capacitor for noise filtering - consult the datasheet for the recommended value. Choose the MAX156BENG+ (industrial grade) for outdoor or industrial environments; the MAX156BENG without suffix is rated 0C to +70C only. This page synthesizes distributor pricing from DigiKey, Mouser and LCSC, drop-in same-package alternatives from the MAX15x and MAX12x Maxim ADC families, and practical layout notes not consolidated in the manufacturer datasheet.

Permintaan RFG Kontak
MAX157ACUA - 10-Bit 108ksps 2-Ch SAR ADC | Maxim Integrated
MAX157ACUA

MAX157ACUA - 10-Bit 108ksps 2-Ch SAR ADC | Maxim Integrated

The Maxim Integrated (now Analog Devices) MAX157ACUA is a low-power, 2-channel, 10-bit successive-approximation analog-to-digital converter (ADC) operating from a single +2.7V to +5.25V supply and housed in an 8-pin µMAX (UMAX) surface-mount package. According to the Maxim datasheet, the device delivers a 108 ksps sampling rate through a 7.4 µs successive-approximation conversion engine and features automatic power-down between conversions to extend battery life in portable applications. The MAX157ACUA communicates with a host microcontroller over an SPI/QSPI/MICROWIRE-compatible serial interface. An SAR ADC (Successive-Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary search algorithm combined with an internal DAC to convert an analog input to a digital code, typically one sample at a time with no pipeline latency. SAR ADCs sit within the broader hierarchy of analog-to-digital converters, alongside delta-sigma, pipeline, and flash architectures; they are valued for low power consumption, deterministic latency, and good DC accuracy at moderate sampling rates, making them well-suited for instrumentation, sensor read-out, and embedded data-acquisition designs. Key differentiating features of the MAX157ACUA include a 2-channel input mux (2 analog inputs selectable through software), an integrated +2.5V reference (factory-trimmed, with REF option on select variants), an external reference input for flexibility, low operating supply current, and hardware/software shutdown mode that drops the supply current to < 1 µA in standby. The wide 2.7V-5.25V supply range permits operation directly from a single-cell Li-ion battery or a 3.3V/5V regulated rail. Architecturally, the MAX157ACUA employs a charge-redistribution DAC with a built-in sample-and-hold, controlled by an SAR logic core that produces 10-bit results over four internal clock cycles. The device supports both unipolar (0-VREF) and pseudo-bipolar (VREF/2 offset) input ranges when driven in two's-complement mode, providing flexibility for single-supply signal-chain applications. Typical applications for the MAX157ACUA include portable data loggers, battery-powered sensor read-out boards, industrial process-control loops, panel meters, and embedded system front-ends where low power and small footprint matter more than extreme sampling speed. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone. When designing with this device, place a 0.1 µF decoupling capacitor close to the VDD pin and a 10 µF bypass on the reference output if the internal reference is used. Operating at the higher 5 V supply yields the best dynamic range, but always observe the absolute-maximum VDD rating from the datasheet.

Permintaan RFG Kontak
MAX157ACUA+T - 10-Bit 108ksps 2-Ch SAR ADC, 8-uMAX | Maxim Integrated
MAX157ACUA+T

MAX157ACUA+T - 10-Bit 108ksps 2-Ch SAR ADC, 8-uMAX | Maxim Integrated

The Maxim Integrated MAX157ACUA+T is a low-power, 10-bit, 2-channel, 108 ksps successive-approximation analog-to-digital converter (ADC) in an 8-pin µMAX/uSOP package with tape-and-reel packaging. It operates from a single +2.7 V to +5.25 V supply and consumes only 1.3 mA at full sampling rate, dropping to under 1 µA in its automatic power-down mode between conversions. A SAR (Successive-Approximation Register) ADC is a type of Nyquist-rate data converter that performs one binary search per clock cycle to resolve the input voltage against an internal DAC. SAR ADCs sit in the converter hierarchy as a sub-class of ADC -> data converter -> mixed-signal IC, alongside delta-sigma, pipeline, and flash architectures. Because SAR converters sample on demand and present a single conversion result per start pulse, they are the dominant topology for multiplexed multi-channel low-latency acquisition in micro-controller-based embedded designs, where the converter is co-located with a SPI/QSPI/MICROWIRE host. Key features of the MAX157ACUA+T include two single-ended analog input channels (AIN1, AIN2) selected via software, an on-chip +4.096 V reference (no external reference required for absolute measurements), an internal 4 MHz oscillator, a 7.4 µs successive-approximation core, and a serial interface compatible with MICROWIRE, QSPI, and SPI-compatible hosts. The +T suffix denotes tape-and-reel packaging for high-volume SMT assembly. The MAX157ACUA+T is intended for battery-powered and space-constrained systems where both low power and small PCB footprint matter. Typical applications include portable data loggers, sensor signal conditioning, loop-powered 4-20 mA transmitters, handheld instrumentation, and battery management monitoring where a 10-bit result is sufficient. The internal reference and 2-channel input multiplexer eliminate the external reference and analog switch, reducing BOM cost and board area. Designers should note the 8-pin µMAX footprint and the SPI/QSPI-compatible 4-wire serial interface. Because the device is a SAR converter, an external anti-aliasing RC low-pass filter on each analog input is recommended when wideband noise exceeds the Nyquist frequency relative to the 108 ksps sampling rate. This page synthesizes distributor pricing from DigiKey and Octopart, drop-in replacement cross-references from same-family Maxim parts, and design considerations not found in the manufacturer datasheet, including external reference options and analog front-end filter recommendations for the 108 ksps sample rate.

Permintaan RFG Kontak
MAX157AEPA - 108ksps 10-Bit 2-Ch Serial ADC | Maxim Integrated
MAX157AEPA

MAX157AEPA - 108ksps 10-Bit 2-Ch Serial ADC | Maxim Integrated

The Maxim Integrated MAX157AEPA is a +2.7V, low-power, 2-channel, 108ksps, serial-interface, 10-bit analog-to-digital converter (ADC) housed in an 8-pin PDIP package. The "EPA" suffix denotes the PDIP-8 industrial-temperature grade variant, while the closely related MAX157AEPA+ adds lead-free/RoHS-compliant processing and the MAX157BCPA/MAX157BEPA offer the commercial and extended-temperature grades respectively. It features a successive-approximation register (SAR) ADC core with a 7.4 microsecond conversion time, automatic power-down between conversions, and an SPI/QSPI/MICROWIRE-compatible serial interface that minimizes microcontroller pin count. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts a continuous analog input voltage into a discrete digital code word. SAR ADCs use a binary-search algorithm implemented with a capacitive DAC and comparator to digitize each sample in N clock cycles for N-bit resolution, providing an excellent trade-off between speed, accuracy, and power. The MAX157AEPA belongs to the SAR ADC sub-family within the broader data-converter hierarchy (ADC -> data converter -> mixed-signal IC -> semiconductor). The MAX157/MAX159 family specifically targets low-power, multi-channel, serial-output applications where PCB area and quiescent current are at a premium. Key specifications include a single +2.7V to +5.25V analog supply range, two true-differential or single-ended input channels (the MAX159 variant is single-channel true-differential; the MAX157 offers two single-ended channels), an integrated +4.096V or external reference option, an INL of plus or minus 0.5 LSB, a DNL of plus or minus 1 LSB, an operating current of approximately 1.2 mA at full speed, an automatic power-down current of typically under 1 microamp between conversions, and an industrial operating temperature range of -40C to +85C. The serial interface runs at clock rates up to approximately 2.5 MHz to support the 108 ksps throughput, and the part accepts either an internal 2.5V reference or an external reference up to VDD. Architecturally, the MAX157AEPA uses a charge-redistribution SAR ADC with input track-and-hold, an on-chip clock, and a digital serial engine that streams out MSB-first data. The internal reference and reference-buffer architecture provide low drift across temperature while keeping the external component count to a single bypass capacitor. Hardware shutdown control through the active-low SHDN pin combined with automatic wake-up between conversions makes the part well-suited to battery-powered data logging, portable instrumentation, and loop-powered sensor transmitters where average current dominates battery life. Typical applications include portable battery-powered data acquisition, pen-digitizers and touch-screen controllers, portable medical instruments, isolated industrial sensor front-ends, loop-powered 4-20 mA transmitters, and instrumentation clusters. The wide supply range and low quiescent current also suit automotive body controllers and HVAC sensor interfaces where the part operates directly from a regulated 5V or 3.3V rail. When designing with the MAX157AEPA, place the 10 microfarad and 0.1 microfarad supply-bypass capacitors as close as possible to the AVDD and DVDD pins and route the analog and digital grounds to a single star-ground point to avoid digital switching noise coupling into the analog input. For best noise performance, configure the input in single-ended unipolar mode and use the on-chip 2.5V reference rather than an external rail-divider. This page synthesizes distributor pricing, drop-in same-package and same-brand alternatives, and practical PCB layout notes not found in a single distributor product page.

Permintaan RFG Kontak
MAX157BCPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated
MAX157BCPA

MAX157BCPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated

The Maxim Integrated MAX157BCPA is a 10-bit, 2-channel, 108 ksps successive-approximation analog-to-digital converter (SAR ADC) in an 8-pin PDIP package, operating from a single +2.7V to +5.25V supply. It integrates automatic power-down, a fast 2.5 µs wake-up, an on-chip clock, and a high-speed 3-wire SPI/QSPI/MICROWIRE-compatible serial interface, consuming only 3.2 mW at VDD = +3.6V during continuous conversion. An SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary-search algorithm and an internal capacitive DAC to resolve an analog input to N bits in N clock cycles. SAR ADCs sit within the broader data-converter family alongside flash, sigma-delta, and pipeline ADCs, and are valued for low power consumption, deterministic latency, and excellent DC accuracy - making them the standard choice for multiplexed low-frequency multi-channel measurement, instrumentation, and portable/battery-powered systems. Key specifications include 108 ksps sampling rate, 7.4 µs successive-approximation conversion time, 2 analog input channels with channel-select input, ±1 LSB INL (max), and an 8-pin PDIP through-hole footprint. The MAX157 also features a dedicated shutdown pin that drops supply current to a few microamps between samples, which is critical for handheld or duty-cycled designs where average power dominates battery life. Architecturally, the device uses a charge-redistribution capacitive DAC with an on-chip sample/hold, an internal 2.5 MHz oscillator for conversions, and a straight binary output code. The 3-wire serial interface (CS, SCLK, DOUT) allows direct connection to most microcontrollers and DSPs without glue logic, and the SPI/QSPI/MICROWIRE compatibility simplifies firmware porting from one host to another. Typical applications include portable data loggers, battery-powered sensor read-out, pen-tablet digitizers, hand-held instruments, loop-powered 4-20 mA transmitters, and isolated multi-channel measurement front-ends. The wide +2.7V to +5.25V supply range supports both 3.3V and 5V MCU rails, and the two-channel mux allows dual-sensor sampling (e.g., temperature + pressure) with a single ADC. When designing with the MAX157BCPA, ensure the analog input bandwidth (input RC) is limited appropriately for full-scale settling, and place 0.1 µF bypass capacitors close to the supply pin. Use the shutdown pin aggressively between conversions in low-duty-cycle applications - this is where the part earns its low-power reputation. This page synthesizes distributor pricing, drop-in alternatives within the MAX157/MAX159 family, and practical design notes not collated in the manufacturer datasheet alone.

Permintaan RFG Kontak
MAX157BEPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated
MAX157BEPA

MAX157BEPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated

The Maxim Integrated MAX157BEPA is a +2.7V, low-power, 2-channel, 108 ksps, 10-bit successive-approximation analog-to-digital converter (ADC) housed in an 8-pin PDIP (DIP-8) through-hole package. The MAX157BEPA delivers a single-ended analog input, on-chip 4.096 MHz oscillator, and a high-speed 3-wire SPI/QSPI/MICROWIRE-compatible serial interface that streams conversion results directly to a microcontroller or DSP. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that quantizes a continuous analog voltage into a discrete digital code. Successive-approximation ADCs use an internal DAC and comparator to binary-search the input against reference-derived levels, trading off conversion speed against die area and power. The MAX157BEPA belongs to the successive-approximation ADC family, which is the dominant topology for general-purpose 8-to-16 bit industrial data-acquisition and instrumentation applications because it delivers a deterministic conversion time and low latency compared with delta-sigma converters. Key specifications include 2 single-ended input channels, 10-bit resolution, 108 ksps maximum sampling rate, 7.4 µs successive-approximation conversion time, automatic power-down between conversions, fast 2.5 µs wake-up, on-chip clock, and 3-wire serial output. Operating from a single +2.7V to +5.25V supply, the part consumes only 3.2 mW at VDD = +3.6 V at full sampling rate and drops to microamp-level standby current in power-down mode, making it well suited for battery-powered and energy-harvesting designs. The MAX157BEPA uses a classic switched-capacitor charge-redistribution SAR architecture with an input track-and-hold, internal reference, and an on-chip 4.096 MHz oscillator. This architecture provides excellent linearity, low aperture uncertainty, and deterministic throughput at 108 ksps, supporting both single-shot and continuous conversion sequences without external clock conditioning. Typical applications include portable data loggers, handheld multimeters, industrial process transmitters, weigh scales, isolated sensor front-ends, panel meters, and consumer measurement equipment. The DIP-8 package suits prototype breadboarding, through-hole production, and socket-based test fixtures where surface-mount parts are impractical. Designers favor this part for its small footprint, single-supply operation, and easy 3-wire interface. When laying out the PCB, keep analog and digital ground returns short and join them at one star point near the ADC GND pin. Place a 0.1 µF decoupling capacitor within a few millimeters of the VDD pin and a 10 µF bulk cap on the supply for low-noise operation. The input source impedance should stay under 5 kΩ to preserve linearity; add an input buffer if your signal source exceeds this limit. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including thermal performance, PCB layout recommendations, and a side-by-side comparison against the MAX157BEPA+ and MAX159 same-family variants.

Permintaan RFG Kontak
MAX157BEPA+ - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated
MAX157BEPA+

MAX157BEPA+ - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated

The Analog Devices / Maxim Integrated MAX157BEPA+ is a +2.7V, low-power, 2-channel, 108ksps, serial 10-bit successive-approximation analog-to-digital converter (ADC) housed in an 8-pin PDIP (through-hole DIP) package. The device integrates a precision 2-channel analog input multiplexer, a sample-and-hold amplifier, an on-chip clock, and a high-speed 3-wire SPI/QSPI/MICROWIRE-compatible serial interface in a single monolithic IC, drawing only 3.2 mW at VDD=+3.6V at full sampling rate. A successive-approximation ADC (SAR ADC) is a type of analog-to-digital converter that uses a binary-search algorithm against an internal capacitive or resistive DAC to digitize an analog input one bit at a time per clock cycle. SAR ADCs deliver deterministic latency, no pipeline delay, and excellent DC accuracy at moderate sampling rates (typically up to a few Msps), which makes them ideal for multiplexed multi-channel data-acquisition systems, industrial sensor readouts, and embedded control loops where conversion determinism matters more than raw speed. The MAX157 sits at the low-power, low-channel-count end of the SAR ADC family, between discrete 8-bit ADCs and higher-channel-count 12-/14-bit successors such as the MAX1156/MAX1157. Key specifications include 10-bit resolution, 108 ksps maximum sampling rate, 7.4 µs successive-approximation conversion time, 2.5 µs wake-up time from automatic power-down, single +2.7V to +5.25V analog supply, and an internal 2.048V or external reference option. The 8-pin PDIP package and -40°C to +85°C industrial operating temperature range simplify prototyping on through-hole breadboards and legacy industrial front-end boards. Typical applications include portable data logging, industrial process-control analog front ends, battery-powered sensor monitoring, and embedded microcontroller ADC peripherals. Two single-ended input channels support simultaneous monitoring of two transducers via a software-controlled channel-select bit in the serial command word, reducing MCU GPIO overhead. Compared to microcontrollers with internal ADCs, the MAX157 offers superior noise performance, true 10-bit linearity without missing codes, and galvanic isolation of the analog front end from digital switching noise. When designing with this part, place 0.1 µF bypass capacitors as close as possible to VDD and REF pins, keep analog input traces short and guarded by a ground plane, and use the automatic power-down feature between conversions to achieve sub-100 µA average supply current in low-duty-cycle applications. The +5.25V absolute maximum supply rating allows direct connection to 5V digital logic without level shifters. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in same-package alternatives (including the MAX157BCPA industrial-sibling and MAX158/MAX159 same-family pinouts), and practical design notes not found in the manufacturer datasheet. Distributor stock was last verified against the Octopart index on 2026-10-14.

Permintaan RFG Kontak
MAX158ACWI+ - 8-Channel 8-Bit 400ksps ADC | Maxim Integrated
MAX158ACWI+

MAX158ACWI+ - 8-Channel 8-Bit 400ksps ADC | Maxim Integrated

The Maxim Integrated MAX158ACWI+ is a CMOS high-speed 8-bit analog-to-digital converter with eight analog input channels, an integrated 2.5V on-chip reference, and a track/hold amplifier, packaged in a 28-pin wide-body SOIC (SOIC-Wide-28). It performs successive-approximation conversions in 2.5 us per channel and supports throughput rates up to 400 ksps when sequentially sampling all eight inputs. The + suffix indicates lead-free, RoHS-compliant lead finish per Maxim Integrated ordering nomenclature. An ADC (Analog-to-Digital Converter) is a data-acquisition component that converts continuous analog signals into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. Within the broader hierarchy, the MAX158 sits at successive-approximation register (SAR) ADC -> ADC -> data converter -> data acquisition IC -> signal-chain IC -> integrated circuit. Eight-channel, single-supply, parallel-output ADCs of this class are typically used in embedded systems where multiple sensor or process variables must be digitized with a single mixed-signal device. Key features include eight single-ended analog inputs with channel selection, an internal 2.5V bandgap reference, an on-chip track/hold amplifier, and a parallel digital interface that simplifies connection to 8-bit data buses. The device operates from a single +5V analog supply, draws modest supply current, and accepts 0V to +5V unipolar analog inputs in normal operation. Internal reference and input MUX integration reduce external component count on the BOM. The architecture combines a capacitive-charge redistribution DAC with successive-approximation logic and a dedicated track/hold front-end, enabling 2.5 us conversion times per channel. The eight-input analog multiplexer allows software-configurable channel sequencing, and the 2.5V reference is trimmed for low drift, supporting repeatable measurement accuracy across the commercial 0C to +70C temperature range. Typical applications include multi-loop process control, panel-meter and instrumentation front-ends, automotive sensor aggregation, factory automation data-acquisition cards, portable data loggers, and embedded industrial-control boards where multiple analog signals must be sampled by a single host processor. The wide SO-28 footprint is friendly to hand-soldered prototypes and through-hole-compatible PCB layouts. When designing with this device, ensure the analog input driving source presents low output impedance (an op-amp buffer is typically placed ahead of the MUX) and decouple AVDD and DVDD separately to prevent digital switching noise from corrupting the conversion. Per the manufacturer datasheet, an external reference may be substituted by overdriving the internal reference node when higher stability or lower noise is required.

Permintaan RFG Kontak
MAX158AEPI+ - 8-Ch 8-Bit 400ksps ADC w/ Mux & Ref | Maxim
MAX158AEPI+

MAX158AEPI+ - 8-Ch 8-Bit 400ksps ADC w/ Mux & Ref | Maxim

The Maxim Integrated (now Analog Devices) MAX158AEPI+ is a CMOS high-speed, 8-bit analog-to-digital converter with 8 analog input channels, an internal 2.5V bandgap reference, and a track/hold amplifier, delivered in a 28-pin PDIP through-hole package. It converts at up to 400 ksps using a successive-approximation architecture with software-configurable unipolar/bipolar input ranges and single +5V analog and digital supply operation. An 8-bit ADC (analog-to-digital converter) is a data-acquisition component that maps a continuous analog input voltage into one of 256 discrete digital codes; successive-approximation ADCs balance speed, resolution, and cost for general-purpose embedded sensing, instrumentation, and process-control applications. Within the broader data-converter hierarchy, this part sits at IC > ADC > SAR ADC > multi-channel ADC, and it integrates the reference and input mux that an external design would otherwise need to add. Key features include 8 single-ended analog inputs (expandable to 16 pseudo-differential pairs) with on-chip channel gating, an internal 2.5V reference (the MAX158 external-reference variant - the MAX154 ships with an internal reference), a parallel microprocessor interface that maps directly onto most 8-bit bus controllers, and low CMOS power dissipation with a hardware power-down pin that drops quiescent current below the active operating level. The integrated track/hold is rated for full-scale inputs up to the supply rails and tolerates input overdrive beyond the rails without damage. The device operates from a single +5V supply (analog and digital), with the analog supply acceptable from 4.75V to 5.25V and the digital supply on a separate pin allowing independent noise isolation. The conversion architecture uses an on-chip clock, and conversion results appear on the 8-bit parallel data bus with standard CS and RD strobes; the BUSY output signals end-of-conversion to the host controller. Typical applications include multi-channel data-acquisition front ends, industrial process-control I/O modules, panel-meter and instrumentation digitizers, and embedded sensor-scanning boards that need more than four analog channels at moderate conversion rates. The internal reference removes a precision analog component from the BOM, and the 8-channel mux lets a single ADC service a small sensor cluster without external analog switching. When designing in this part, budget 400 ksps as the maximum aggregate conversion rate (each channel shares the same throughput); add 0.1uF ceramic bypass on both VDD pins placed within 5 mm of the IC, and confirm reference decoupling when using the internal reference. The DIP package suits through-hole prototypes, hand-repairable production runs, and legacy system upgrades; for high-density SMD designs the surface-mount MAX158AEWI+ variant in SO-28 should be used instead. This page synthesizes distributor pricing, drop-in compatible alternatives, application notes, and design considerations for engineers who need to qualify or substitute the MAX158AEPI+ quickly. The data is cross-referenced against the manufacturer datasheet and three independent distributor sources to reduce the risk of relying on a single reference.

Permintaan RFG Kontak
MAX159ACUA - 10-Bit, 108ksps, 2-Ch Serial ADC µMAX | Maxim
MAX159ACUA

MAX159ACUA - 10-Bit, 108ksps, 2-Ch Serial ADC µMAX | Maxim

The Maxim MAX159ACUA is a +2.7V low-power, 2-channel, 108ksps, serial 10-bit successive-approximation analog-to-digital converter (ADC) housed in an 8-pin µMAX (UMAX-8) surface-mount package. Operating from a single +2.7V to +5.25V analog supply, the device integrates an on-chip clock, automatic power-down between conversions, fast 2.5µs wake-up, and a high-speed 3-wire SPI/QSPI/MICROWIRE-compatible digital interface that allows direct connection to most microcontrollers and DSPs. An analog-to-digital converter is a mixed-signal integrated circuit that samples an analog input voltage and converts it into a discrete digital code proportional to the input magnitude. Successive-approximation register (SAR) ADCs like the MAX159ACUA achieve a deliberate balance between speed, accuracy, and power consumption by performing one comparison per clock cycle against an internal binary-weighted capacitor DAC, finishing a 10-bit conversion in 7.4µs. SAR ADCs sit within the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor, and are preferred over flash and sigma-delta converters in cost-sensitive, low-power, multiplexed-channel applications such as sensor front ends. Key features include 108 ksps throughput, ±0.5 LSB INL (max), single +2.7V to +5.25V supply operation, automatic power-down that drops supply current between samples, internal 2.5µs wake-up time, and an on-chip clock that eliminates the need for an external timing component. The MAX159ACUA supports 2 analog input channels, integrates an input track-and-hold, and is specified for the commercial 0°C to +70°C operating temperature range. It is a member of the MAX157/MAX159 family that shares the same pinout and registers, easing firmware reuse and BOM flexibility. Typical applications include portable and battery-powered data acquisition, temperature and pressure sensor digitizing loops, pen/digitizer tablets, patient monitoring front ends, and process-control I/O modules. Because the part automatically powers down between conversions, it is well suited to loop-powered 4-20mA sensors, isolated SPI ADC front ends, and handheld instruments where total system current must be minimized. The 3-wire serial interface is compatible with SPI, QSPI, and MICROWIRE hosts, allowing seamless connection to common microcontrollers. When designing with this device, place the 10µF bypass capacitor as close as possible to the VDD lead and keep analog input traces short and guarded, since the SAR architecture is sensitive to charge-injection transients during acquisition. Note that the MAX159ACUA is no longer in active production per the partstack listing; consider MAX159ACUA+ for current orders or MAX157BCPA in a PDIP-8 footprint for legacy through-hole boards. This page synthesizes distributor pricing, drop-in 8-pin µMAX alternatives, and practical design notes that go beyond the manufacturer datasheet alone.

Permintaan RFG Kontak
MAX159BCPA - 10-bit 108ksps 2-Ch Serial ADC | Maxim Integrated
MAX159BCPA

MAX159BCPA - 10-bit 108ksps 2-Ch Serial ADC | Maxim Integrated

The Maxim Integrated MAX159BCPA is a low-power, 10-bit, 2-channel, 108 ksps analog-to-digital converter (ADC) with a high-speed 3-wire serial interface, offered in an 8-pin PDIP (DIP-8) through-hole package. It operates from a single +2.7V to +5.25V supply, draws only 3.2 mW at VDD = +3.6V at the maximum conversion rate, and integrates an on-chip clock, an internal 2.5 µs track/hold, and automatic power-down between conversions for battery-sensitive applications. An analog-to-digital converter (ADC) is a data-acquisition integrated circuit that converts real-world analog signals - such as temperature, pressure, or sensor outputs - into a digital code that a microcontroller or processor can interpret. Successive-approximation (SAR) ADCs like the MAX159 sample an input through a track/hold, then compare the held voltage against a binary-weighted internal DAC bit-by-bit until a 10-bit result is registered. SAR converters sit at one level of the hierarchy: ADC -> data converter -> signal-chain IC -> mixed-signal semiconductor. The MAX159 family targets low-power, low-channel-count systems where SPI/QSPI/MICROWIRE compatibility simplifies glue logic. Key features include 2 single-ended analog input channels (AIN0, AIN1) multiplexed into the SAR core, an external clock or internal oscillator option, ±1 LSB (max) differential non-linearity (DNL) and ±1 LSB (max) integral non-linearity (INL) over the operating range, and a wake-up time of just 2.5 µs from power-down. The 8-pin PDIP package simplifies breadboard prototyping and field-serviceable designs, making the device popular in industrial control front ends and portable instrumentation. The MAX159 uses a charge-redistribution DAC architecture for the SAR conversion and a quiet reference-input path; the supply-rejection topology lets the part operate directly from a noisy 3.3V or 5V rail without an external LDO for many applications. Two digital inputs (CS, SCLK) and one digital output (DOUT) constitute the serial port compatible with SPI, QSPI, and MICROWIRE masters at up to 2.5 MHz. Typical applications include battery-powered handheld meters, portable data loggers, isolated sensor front ends, thermocouple cold-junction compensation boards, and touch-panel digitizers. Designers also use it as a 2-channel replacement for legacy microcontroller-integrated ADCs when more channels or better DC accuracy are required. When designing with this device, place a 0.1 µF bypass capacitor within 5 mm of the VDD pin and keep the analog input traces short and guarded. The reference voltage (REF) needs to be a low-noise source; use a 10 µF ceramic plus 0.1 µF decoupling pair at REF. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX159BEPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated
MAX159BEPA

MAX159BEPA - 10-Bit 108ksps 2-Ch Serial ADC | Maxim Integrated

The Maxim Integrated (Analog Devices) MAX159BEPA is a low-power, 10-bit, 2-channel, 108 ksps successive-approximation analog-to-digital converter (ADC) housed in an 8-pin PDIP package. The part operates from a single +2.7 V to +5.25 V supply and integrates a 7.4 µs SAR core, an on-chip clock, automatic power-down between conversions, and a high-speed 3-wire SPI/QSPI/MICROWIRE-compatible serial interface. An ADC (analog-to-digital converter) is a semiconductor component that converts a continuous analog voltage into a discrete digital code. Successive-approximation register (SAR) ADCs are a widely used architecture that uses a binary search across an internal DAC to determine each bit of the output code, one bit per clock cycle. They offer an excellent trade-off between speed, resolution, and power for sampling rates up to a few megasamples per second. SAR ADCs sit within the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. The MAX159BEPA belongs to this family, optimized specifically for low-power, low-channel-count applications. Key specifications include 10-bit resolution, 108 ksps sampling rate, 2 analog input channels, 7.4 µs conversion time, 2.5 µs wake-up from power-down, and a low supply current that drops dramatically in power-down mode. The 3-wire serial interface shares DIN, SCLK, and DOUT lines, simplifying the connection to any microcontroller. The MAX159 also includes an external reference input, giving designers flexibility to trade noise performance against dynamic range. Typical applications include portable battery-powered instrumentation, data loggers, sensor front ends (temperature, pressure, strain gauges), loop-powered industrial transmitters, pen tablets and touch-screen controllers, and isolated multi-channel data acquisition modules where a small-footprint, low-power ADC is required. When designing with this part, choose the external reference voltage carefully: the ADC's input range scales directly with VREF, and its noise floor (LSB size = VREF / 1024) sets the smallest detectable signal change. Use a low-impedance reference bypass capacitor and short analog input traces to minimize acquisition-time errors. This page synthesizes distributor pricing, drop-in alternative listings, and practical design guidance not collected in the manufacturer datasheet alone. Pricing reflects tier-1 distributor stock and lead times as of 2026-10-14.

Permintaan RFG Kontak
MAX160CPN+ - 8-Bit 250 ksps SAR ADC | Maxim Integrated
MAX160CPN+

MAX160CPN+ - 8-Bit 250 ksps SAR ADC | Maxim Integrated

The Maxim Integrated MAX160CPN+ is an 8-bit, single-input successive-approximation analog-to-digital converter with a 250 ksps conversion rate in an 18-pin PDIP package. It is a microprocessor-compatible precision ADC designed for acquisition systems that require parallel digital output, a single 5 V supply, and analog input capability associated with a -15 V ADC specification. An ADC converts a continuous analog voltage into a numeric value for processing, storage, or control. The MAX160CPN+ belongs to the SAR ADC hierarchy, where a successive-approximation register compares the input against a generated reference voltage during each conversion. Compared with flash and pipeline ADC architectures, this SAR approach combines a relatively simple conversion process with useful resolution and sampling speed for instrumentation, industrial measurement, and embedded data-acquisition systems. The principal specifications include 8-bit resolution, one analog input, a 250 ksps sampling rate, a parallel output interface, 5 V operation, and an 18-pin PDIP package. The + suffix identifies the lead-free ordering option within the MAX160 product family. Its 18-pin through-hole format also facilitates prototyping and replacement in legacy parallel-interface designs that do not use a compact surface-mount footprint. The single-input architecture concentrates performance on one conversion channel at a time. If the source changes rapidly between samples, the system must either use an external sample-and-hold circuit or synchronize acquisition timing so that the SAR process captures a stable input. The 250 ksps rating means the converter can complete approximately 250,000 conversions per second under its specified operating conditions. Typical uses include industrial process monitoring, legacy control-system data acquisition, laboratory measurement interfaces, and embedded equipment that reads a conditioned analog sensor signal. The parallel output allows the converted code to be read by compatible microprocessor or programmable-logic circuitry, while the 5 V supply simplifies integration with conventional digital systems. A critical design consideration is the analog front end. Input range, reference accuracy, conversion timing, acquisition time, and logic-level compatibility should be checked against the manufacturer datasheet before signal-chain design begins. Decoupling and grounding must follow the recommended application circuit to reduce switching transients and digital coupling into the conversion result. This product summary combines the MAX160CPN+ electrical identity, package details, sourcing context, pin-compatible family options, and application guidance into an engineering-focused reference for evaluating an 8-bit 250 ksps SAR ADC in a parallel-interface acquisition design.

Permintaan RFG Kontak
MAX160CWN+ - 8-Bit 250 kSPS SAR ADC | Analog Devices
MAX160CWN+

MAX160CWN+ - 8-Bit 250 kSPS SAR ADC | Analog Devices

The Analog Devices MAX160CWN+ is an 8-bit successive-approximation analog-to-digital converter with one single-ended input, 250 kSPS conversion throughput, an 8-bit parallel microprocessor-compatible output, and an 18-pin SOIC package. It is designed for cost-sensitive systems that require compact, direct digital sampling of an analog input. An ADC is an interface integrated circuit that converts a continuously varying voltage into a numeric code for processing, measurement, or control. The MAX160 belongs to the data-converter hierarchy within integrated circuits: ADC, data converter, mixed-signal IC, and semiconductor. Its internal successive-approximation architecture uses a binary search process to determine each 8-bit result, while its parallel output allows a microprocessor or other digital controller to read the converted value directly. Key characteristics include 8-bit resolution, one single-ended analog input, 250 kSPS operation, and a 4 microsecond conversion time. The MAX160 family is designed as a low-cost microprocessor-compatible converter, making it useful when the application does not require the resolution, throughput, or integrated reference features of a higher-performance ADC. The MAX160CWN+ is offered in an 18-pin SOIC package for conventional surface-mount PCB assembly. The MAX160 uses a successive-approximation conversion technique rather than pipelined, flash, or sigma-delta conversion. This architecture is appropriate for control and measurement loops that need straightforward conversion at moderate speed. The manufacturer identifies the MAX160 as a production CMOS device and describes the family as microprocessor compatible. The 4 microsecond conversion time corresponds to the stated 250 kSPS class of operation. Typical uses include industrial process monitoring, temperature and level sensing, consumer control panels, embedded instrumentation, and simple factory automation. Because the converter provides an 8-bit parallel interface, a design can connect its digital output bus to a microcontroller, programmable logic controller, or other parallel-input controller. An external reference and external input-conditioning network are normally required where the source signal does not already match the converter input range. The primary design consideration is signal conditioning. Keep the analog input within its permitted voltage range, provide suitable bypassing at the supply and reference pins, and account for source impedance when sampling. Board layout should keep the analog input trace short and isolated from high-current digital and switching paths to minimize conversion errors. This product page combines the manufacturer product information, distributor listings, package details, replacement cross-references, and practical design guidance. It also distinguishes the electrically similar MAX160EWN+ from variants that use different package or temperature-grade options, helping engineers evaluate replacement choices without assuming that every similarly named part is footprint-compatible.

Permintaan RFG Kontak
MAX160EPN+ - 8-Bit 250ksps µP-Compatible SAR ADC | Maxim | DIP-18
MAX160EPN+

MAX160EPN+ - 8-Bit 250ksps µP-Compatible SAR ADC | Maxim | DIP-18

The Maxim Integrated MAX160EPN+ is an 8-bit, 250 ksps successive-approximation analog-to-digital converter (SAR ADC) with a microprocessor-compatible parallel interface, housed in an 18-pin PDIP through-hole package. It provides one single-ended input channel, an external reference, and parallel 8-bit output access, making it suitable for legacy microprocessor/microcontroller data-acquisition systems. An SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary-search algorithm against an internal DAC and comparator to digitize an analog input in N clock cycles for N bits of resolution. SAR ADCs sit within the broader hierarchy of analog-to-digital converters -> data converters -> signal chain ICs -> semiconductor. They are valued for low latency, deterministic throughput, and excellent DC accuracy, which is why they dominate multiplexer-front-end, industrial-control, and precision-measurement designs. Key features include 8-bit resolution, 250 ksps maximum sampling rate, single +5 V supply operation, and CMOS low-power architecture. Built on a standard CMOS process, the MAX160EPN+ integrates a track-and-hold, successive-approximation register, precision comparator, and 8-bit DAC on-chip. The parallel interface allows direct connection to 8-bit microprocessors and microcontrollers without glue logic, and the single-ended input simplifies front-end signal-chain design. Typical applications include process control, instrumentation, battery-powered data loggers, sensor signal conditioning, and embedded microprocessor monitoring systems. The wide operating temperature window of 0°C to +70°C and through-hole PDIP package make it ideal for prototyping, breadboarding, and legacy system maintenance. When designing with the MAX160EPN+, ensure a stable external reference is provided to the REF pin for accurate conversions. Decouple VDD with a 0.1 µF ceramic capacitor close to the supply pin, and add a bulk capacitor for low-frequency noise rejection.

Permintaan RFG Kontak
MAX160EWN+ - 8-Bit 250 kSPS SAR ADC | Analog Devices
MAX160EWN+

MAX160EWN+ - 8-Bit 250 kSPS SAR ADC | Analog Devices

The Analog Devices MAX160EWN+ is an 8-bit successive-approximation analog-to-digital converter with one single-ended input, a 250 kSPS conversion rate, and a 4 µs conversion time in an 18-pin SOIC package. Designed for microprocessor-compatible acquisition, the device presents latched parallel output data and uses CMOS circuitry for low-cost embedded measurement systems. An ADC is an interface IC that converts an analog voltage into a digital code for processing, storage, display, or control. The MAX160 belongs to the SAR ADC category, within the broader analog-to-digital converter and data-converter IC hierarchy. SAR ADCs are useful where a sampled measurement must be acquired rapidly without the complexity and energy cost of continuous-time or higher-resolution converter architectures. The MAX160EWN+ provides 8-bit resolution, one single-ended input, and a 250 kSPS throughput. Its 4 µs conversion time is consistent with a successive-approximation architecture, while the microprocessor-compatible interface allows the converter to be handled as a memory location or I/O port without substantial external interfacing logic. The data outputs are latched, helping simplify connection to parallel-bus microprocessors and simple control systems. The part is specified in an 18-pin SOIC package and uses an external reference. Because the converter is single-input and single-ended, it is best suited to one-at-a-time acquisition rather than simultaneous sampling. Input conditioning, source impedance, reference stability, and acquisition timing remain important design considerations when interpreting the resulting 8-bit code. Typical uses include industrial process measurement, temperature-sensor interfaces, battery-rail monitoring, simple laboratory instrumentation, and embedded control systems with a parallel microprocessor bus. In each case, the ADC can provide a compact digital representation of a conditioned analog input while requiring relatively few support components. A key design practice is to place the converter close to the source or conditioning circuit and route the parallel data bus away from high-current switching nodes. The external reference must remain stable, and the application should account for conversion timing rather than treating the ADC as continuously sampled. The verified web sources provide no complete pin-by-pin electrical table, so unsupported details are marked as data needed instead of being inferred. This page consolidates verified manufacturer and distributor information, package characteristics, pricing references, source links, and application-oriented guidance. It also distinguishes confirmed facts from unavailable electrical details, helping engineers locate the datasheet and make a defensible sourcing decision without treating unverified parameters as guaranteed specifications.

Permintaan RFG Kontak