Produk (46.000+)

MAX196ACAI - 12-Bit 6Ch DAS, ±10V, 100kSPS, 28-SSOP | Maxim Integrated
MAX196ACAI

MAX196ACAI - 12-Bit 6Ch DAS, ±10V, 100kSPS, 28-SSOP | Maxim Integrated

The Maxim Integrated MAX196ACAI is a 12-bit, 6-channel, multi-range data-acquisition system (DAS) with 12-bit parallel bus interface, sampling at up to 100 kSPS and housed in a 28-pin SSOP (5.3 mm body width) package. It operates from a single +5 V analog supply and integrates a fault-protected analog input multiplexer, track/hold, successive-approximation ADC core, internal 4.096 V reference (or external reference option), and a microprocessor-compatible 12-bit parallel interface. A data acquisition system (DAS) is an integrated analog-front-end subsystem that combines input multiplexing, signal conditioning, sampling, and digital conversion into a single IC. It sits between the analog sensor world (transducers, ±10 V industrial signals, 4-20 mA loops) and a microprocessor or DSP, replacing the discrete chain of analog mux + op-amp driver + SHA + ADC + reference. The MAX196 belongs to the broader category of analog-to-digital converters (ADCs) and more specifically to multi-channel DAS ICs optimized for industrial-control front ends. Key features include 12-bit resolution with ±1/2 LSB linearity, software-programmable input ranges per channel (0 to +5 V, 0 to +10 V, ±5 V, ±10 V on MAX196), ±16.5 V fault-protected analog inputs that survive transients beyond the supply rails, an internal 4.096 V reference, and software-configurable acquisition/track mode for low-distortion sampling. The 100 kSPS throughput supports process-control loop rates, while the parallel bus interface eliminates the bit-banging overhead of serial ADCs in legacy 8/16-bit microcontroller designs. Architecturally, the part uses a charge-redistribution successive-approximation ADC with a laser-trimmed DAC array, delivering 73 dB SINAD and 83 dB spurious-free dynamic range at the Nyquist input. The on-chip reference and input-protection FETs are designed for industrial environments where common-mode voltages and ESD events routinely exceed standard ADC input tolerances. Typical applications include industrial process-control front ends (PLC analog input modules), multi-channel data loggers, instrumentation front panels, and multi-sensor embedded systems. Engineers reach for the MAX196 when they need true bipolar ±10 V industrial ranges without external resistor dividers, plus fault protection that lets the IC survive wiring faults on factory floors. When designing with this part, observe the analog supply decoupling rules (10 µF tantalum + 0.1 µF ceramic close to AV+ pin) and place a 0.1 µF bypass on the +5 V logic supply. The internal reference can be overdriven by an external ADR0x reference for higher absolute accuracy in calibrated instrumentation. This page synthesizes distributor pricing, SSOP drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-comparison against MAX196AEAI+ (extended-temperature grade), MAX196ACWI+ (SOIC-28 wide), and pin-compatible multi-channel DAS parts from Analog Devices.

Permintaan RFG Kontak
MAX196AEAI - 12-Bit 100kSPS 6-Ch ±10V DAS ADC, SSOP-28 | Maxim
MAX196AEAI

MAX196AEAI - 12-Bit 100kSPS 6-Ch ±10V DAS ADC, SSOP-28 | Maxim

The Maxim Integrated (Analog Devices) MAX196AEAI is a multi-range, 12-bit data-acquisition system (DAS) that integrates a 6-channel analog input multiplexer, track-and-hold amplifier, successive-approximation register (SAR) ADC, and on-chip reference. It operates from a single +5V supply while accepting analog inputs as large as ±10V, samples at up to 100 kSPS, and presents data through a parallel interface. It is offered in a 28-pin SSOP package (EAI suffix) for surface-mount industrial designs. A Data Acquisition System (DAS) such as the MAX196 is a category of mixed-signal IC that combines the front-end signal conditioning (input mux, protection, T/H), the analog-to-digital conversion stage, and a digital host interface into a single device. Within the broader hierarchy of ICs, the MAX196 sits as: ADC -> Data Acquisition System -> Data Converter -> Mixed-Signal IC -> Semiconductor. Its primary value is replacing multiple discrete components (input protection resistors, mux, op-amp T/H, separate SAR, reference) with one chip, reducing BOM cost, board area, and design complexity. Key features include software-selectable input ranges per channel (±10V, ±5V, 0 to 10V, 0 to 5V for MAX196; ±4V, 0 to 4V for MAX198), internal 4.096V reference (with option to overdrive), ±1/2 LSB linearity (A grade), ±16.5V input protection (continuous), 6 analog input channels, three-state bi-directional data port compatible with 8/16-bit buses, and TTL/CMOS-compatible I/O. Internal sequential channel scanning plus user-programmable channel sequencing support per-channel setup. Architecturally, the device uses a capacitive-charge-distribution SAR converter with auto-calibration logic that nulls gain and offset errors at power-up. The on-chip reference is a buried Zener type with 50 ppm/°C typical drift. Analog inputs are routed through a fault-protected CMOS mux that tolerates overvoltages well beyond the supply rails without latch-up. Typical applications include industrial process control and PLC analog front ends, multi-channel data loggers, portable instrumentation, medical patient monitoring equipment, and rack-mounted test and measurement systems where ±10V industrial signal ranges must be digitized directly from a +5V-only supply. A key design tip: route AGND and DGND as a star-ground topology and decouple the +5V AVCC pin with both a 0.1 µF ceramic and a 10 µF tantalum as close to the IC as possible. For ±10V input ranges, use the internal 4.096V reference mode and rely on the on-chip dividers; for high-accuracy systems, drive REFADJ with a low-noise external op-amp or use the external-reference mode. This page synthesizes distributor pricing, drop-in alternatives drawn from Maxim's same product family (A/B/C grades, plus the +5V-only companion MAX198), and practical PCB layout guidance not consolidated in the original datasheet.

Permintaan RFG Kontak
MAX196AENI - 12-Bit 6-Ch 100ksps Precision ADC | Maxim Integrated
MAX196AENI

MAX196AENI - 12-Bit 6-Ch 100ksps Precision ADC | Maxim Integrated

The Maxim Integrated (now Analog Devices) MAX196AENI is a multi-range, single +5V, 12-bit data-acquisition system (DAS) with 12-bit bus interface, sampling at 100 ksps across 6 analog input channels and housed in a 28-pin PDIP (N) through-hole package. Its core headlines are a 6-channel single-ended or 6-channel pseudo-differential input mux, software-selectable input ranges (0 to +5V, 0 to +10V, ±5V, ±10V, 0 to +4.18V) and a successive-approximation ADC with 100 ksps throughput. A Data Acquisition System (DAS) is an integrated subsystem that combines analog input multiplexing, sample-and-hold, ADC conversion, and a digital interface in a single IC, eliminating the need for the designer to pair a discrete mux, S/H, and ADC. The MAX196 belongs to the precision SAR-ADC > multi-channel DAS > data-converter > signal-chain IC product hierarchy. The DAS sits between sensors/transducers and the host microcontroller or DSP, providing a clean digital representation of multiple analog signals with high noise immunity and bus-friendly I/O. Key differentiating features include 6 input channels in a single device (vs. typical 1 or 2 for standalone ADCs), software-programmable input ranges via internal PGA/scaling, a built-in track-and-hold and 4.096V reference, a 100 ksps conversion rate at ±1/2 LSB linearity, and a parallel 12-bit/8-bit bus interface that drops directly onto most 80xx-family microprocessors. The device operates from a single +5V supply and consumes 60 mW typical during conversion. TTL/CMOS-compatible I/O simplifies interface to modern MCUs without level shifters. Typical applications include process control, industrial data acquisition, instrumentation, automated test equipment (ATE), and embedded sensor monitoring. The parallel bus interface makes it particularly well suited to legacy 80xx designs and DSPs needing fast multi-channel capture, while the wide input-range flexibility lets a single board accept 4-20mA, 0-10V, and bipolar transducer outputs without external signal conditioning. A design consideration: the parallel interface consumes many MCU pins, so consider an SPI-based successor such as MAX197 or MAX1300-series parts for new designs with pin constraints. Decouple the supply with a 0.1uF ceramic plus a 10uF tantalum adjacent to the +5V and DGND pins.

Permintaan RFG Kontak
MAX197ACAI+T - 12-Bit 100kSPS DAS, 28-SSOP | Analog Devices
MAX197ACAI+T

MAX197ACAI+T - 12-Bit 100kSPS DAS, 28-SSOP | Analog Devices

The Analog Devices MAX197ACAI+T is a 12-bit, 100kSPS multi-range Data Acquisition System (DAS) requiring only a single +5V supply, packaged in a 28-pin SSOP (5.30mm width). It integrates a 12-bit successive-approximation ADC with an 8-channel analog input multiplexer, sample-and-hold, and a microprocessor-compatible parallel interface in one IC. A DAS (Data Acquisition System) is a mixed-signal integrated circuit that combines analog front-end multiplexing, sample-and-hold buffering, an analog-to-digital converter, and a digital interface into a single device. Within the broader product hierarchy, the MAX197 belongs to the SAR ADC (Successive Approximation Register Analog-to-Digital Converter) family, itself a sub-category of data converters (ADC) which sit inside the signal-chain / mixed-signal power management hierarchy. Its primary engineering value is replacing multi-chip discrete ADC designs with a single calibrated IC that handles analog signal conditioning, range scaling, and digital readout. Key features include software-selectable input ranges of ±10V, ±5V, 0 to +10V, and 0 to +5V, all derived from the internal 4.096V reference and on-chip range-switching network; 1/2 LSB linearity (A-grade); an 8-channel analog multiplexer with two software-selectable acquisition modes (8 single-ended or 4 differential); an 8+4 parallel bus interface with three-state I/O; and TTL/CMOS-compatible digital I/O. Operating from a single +5V supply, the part accepts bipolar input signals that exceed the supply rails, which removes the need for external negative supplies or input level shifters. The MAX197 uses a capacitive-DAC SAR architecture with an inherent track-and-hold input stage, achieving 100kSPS throughput at 12 bits and ±1/2 LSB integral nonlinearity (A grade). An internal 4.096V bandgap reference and flexible input-range scaling allow direct connection to industrial ±10V or 0-10V transducer outputs without external op-amp signal conditioning. The 8+4 parallel interface mode is compatible with 8-bit microprocessors, while the chip's internal mode register lets the host software configure channels and ranges on a per-conversion basis. Typical applications include industrial process control data acquisition, multichannel sensor interfacing, factory automation I/O modules, test and measurement front-ends, and any embedded system that requires 12-bit resolution across multiple bipolar input ranges without a negative supply rail. Its combination of bipolar-input capability, internal reference, and parallel interface makes it well suited to legacy 8-bit bus designs being upgraded to higher-performance mixed-signal front ends. When designing with this device, observe the recommended decoupling and analog-input layout practices. Place a 0.1µF ceramic bypass capacitor close to the +5V pin and a 10µF tantalum reservoir on the supply rail; use ground-plane construction and keep analog input traces short and away from digital switching lines. Verify that software-controlled channel/range selection bits are written before initiating a conversion to avoid invalid data. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX197AENI - 12-Bit 100ksps 8-Ch DAS ADC | Maxim Integrated
MAX197AENI

MAX197AENI - 12-Bit 100ksps 8-Ch DAS ADC | Maxim Integrated

The Maxim Integrated MAX197AENI is a multi-range, 12-bit data-acquisition system (DAS) requiring only a single +5V supply, yet accepting analog input signals that may span both above the power-supply rail and below ground. Packaged in a 28-pin PDIP through-hole package, the device integrates an 8-channel analog input multiplexer, sample-and-hold, and a successive-approximation ADC achieving 100 ksps throughput with ±0.5 LSB integral nonlinearity in the A-grade variant. The device operates from a single +5V supply while supporting bipolar input ranges of ±10V, ±5V, 0-10V, and 0-5V through software-configurable internal scaling resistors. A 12-bit analog-to-digital converter is a successive-approximation ADC that converts continuous analog signals into discrete 12-bit digital codes, balancing resolution against sampling speed for industrial, instrumentation, and process-control applications. As a member of the data-acquisition IC family, the MAX197 sits in the hierarchy of ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Its integrated front-end eliminates external signal-conditioning components, simplifying PCB design for multi-channel systems. Key features of the MAX197AENI include eight analog input channels with software-selectable input ranges, 100 ksps sampling rate, internal 4.096V reference (with optional external reference override), three-state data I/O port configurable for 8-bit buses, and TTL/CMOS-compatible digital I/O. The device also provides hardware- or software-triggered conversions, an end-of-conversion interrupt, and built-in overvoltage protection of ±25V on analog inputs without damage. Architecturally, the MAX197 employs a successive-approximation register (SAR) ADC core with an input multiplexer feeding a unity-gain sample/hold amplifier. The internal scaling resistors and reference buffer allow direct connection to high-voltage bipolar signals when operating from a single +5V rail. The internal reference may be bypassed in favor of an external ADRXXX-series reference for higher absolute accuracy. Typical applications include industrial process control, data loggers, robotics, pen tablet digitizers, and medical instrumentation. The wide input range capability (especially ±10V bipolar from a single +5V rail) makes it ideal for industrial sensors and PLC analog input modules. When designing with the MAX197, ensure that the analog input source impedance stays below the datasheet maximum (typically 1 kΩ for full accuracy) and that adequate decoupling (10 µF + 0.1 µF) is placed at AVDD and DVDD. The +5V single-supply operation significantly simplifies power tree design compared to bipolar-input ADCs requiring ±15V rails. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes beyond the manufacturer datasheet.

Permintaan RFG Kontak
MAX198ACNI - 12-Bit 6-Ch 100ksps ADC | Maxim | Multi-Range
MAX198ACNI

MAX198ACNI - 12-Bit 6-Ch 100ksps ADC | Maxim | Multi-Range

The Maxim Integrated MAX198ACNI is a 6-channel, multi-range, 12-bit data-acquisition system (DAS) with successive-approximation register (SAR) architecture, providing up to 100 ksps sampling rate on a single +5 V supply. Housed in a 28-pin PDIP (N) through-hole package, the device accepts analog inputs ranging up to ±4 V (MAX198) or ±10 V (MAX198 variant) with software-configurable input ranges of 0 to 10 V, 0 to 5 V, ±10 V, ±5 V, 0 to 4 V, and ±4 V, allowing a single IC to interface with multiple sensor signal levels without external scaling. An ADC (analog-to-digital converter) is a mixed-signal data converter that translates real-world analog voltages into a digital code for processing by microcontrollers, DSPs, or FPGAs. As a multi-range SAR ADC, the MAX198ACNI uses a charge-redistribution DAC and comparator to perform a 12-bit conversion in under 10 µs, balancing speed, accuracy, and simplicity. Its place in the broader taxonomy: ADC -> data converter -> mixed-signal IC -> power management / signal chain. The internal reference and rugged bipolar input structure simplify signal conditioning for industrial control loops. Key features include six analog input channels multiplexed to a single 12-bit ADC core, eight software-programmable input ranges, an internal 4.096 V reference, a three-state parallel digital interface compatible with 16-bit data buses, and TTL/CMOS-compatible logic levels. The 100 ksps throughput makes it suitable for closed-loop control and instrumentation sampling. Power dissipation is approximately 60 mW during continuous conversion and drops to under 1 mW in software-controlled power-down mode, which is valuable for battery-portable instrumentation. Typical applications include multi-channel industrial process-control data acquisition, programmable-logic controller (PLC) analog input modules, medical instrumentation signal conditioning, automated test equipment (ATE) front-ends, and embedded sensor-interface boards. The multi-range input allows direct connection to 4-20 mA current-loop receivers (with a sense resistor), thermocouple amplifiers, and strain-gauge bridges. When designing with the MAX198ACNI, bypass VDD and VSS pins with 0.1 µF and 10 µF capacitors placed within 5 mm of the device, route analog and digital grounds separately back to a star-point ground, and ensure the input signal does not exceed ±16 V absolute maximum to avoid input-protection diode conduction. The 'A' grade provides ±0.5 LSB INL and the 'C' suffix denotes the commercial 0 °C to +70 °C operating range. This page synthesizes real distributor stock, parametric drop-in alternatives, and PCB design guidance not found in the bare Maxim datasheet.

Permintaan RFG Kontak
MAX198ACWI - 6-Channel 12-Bit DAS, 5V, 100kSPS | Maxim/ADI
MAX198ACWI

MAX198ACWI - 6-Channel 12-Bit DAS, 5V, 100kSPS | Maxim/ADI

The Analog Devices (formerly Maxim Integrated) MAX198ACWI is a 6-channel, multi-range, 12-bit Data Acquisition System (DAS) with a 12-bit parallel bus interface, packaged in a 28-pin wide SOIC. It performs successive-approximation analog-to-digital conversion at up to 100 ksps on six software-selectable analog input channels, and operates from a single +5 V supply, drawing 7.5 mA (typ) operating and 1 mA (typ) in power-down mode. A Data Acquisition System (DAS) such as this combines a multi-channel input multiplexer, a sample-and-hold amplifier, a SAR (Successive Approximation Register) ADC core, voltage reference support, and a digital bus interface into a single IC. The MAX198ACWI sits in the ADC IC family, beneath the broader category of data-conversion / data-acquisition semiconductors, and is used as the analog front-end in distributed control, instrumentation, and embedded systems where multiple analog signals must be digitized and delivered to a host CPU or DSP over a fast parallel port. Key features include software-configurable unipolar input ranges of 0 V to +VREF (where VREF is the internal 4.096 V bandgap or an external reference) and 0 V to +5 V, 6.0 us conversion time, an internal 4.096 V reference, and AC + DC (±1/2 LSB) linearity over the operating range. Software-configurable bipolar ranges (±VREF, ±5 V on the MAX196, ±10 V on the MAX197) are the user's choice. The three-state bidirectional data port is compatible with 16-bit data buses, and bus-release timing is matched to the read cycles of most 8051-family, 68HC11, and similar microprocessors. All digital I/O are TTL/CMOS compatible, simplifying level translation in mixed-voltage designs. Architecturally, the device uses a charge-redistribution SAR ADC with an input fault-protected multiplexer that tolerates ±16.5 V overvoltage on any analog input without damage. The internal reference can be overdriven externally for high-accuracy applications. MAX198ACWI is the commercial-temperature (0 °C to +70 °C) grade; MAX198AEWI extends the range to -40 °C to +85 °C. Typical applications include multi-channel data-acquisition front ends for industrial process control, PLC analog input modules, weigh scale and bridge-sensor digitizers, temperature-monitoring multiplexers (thermocouple/RTD via external signal conditioning), portable instrumentation, and battery-cell monitoring in UPS and renewable-energy systems. Embedded-system designers favor the part for its 6 multiplexed channels on one ADC, eliminating external analog switches and reducing both BOM and PCB area. When designing with the MAX198ACWI, ensure the analog inputs remain within ±16.5 V to avoid stressing the input-protection network, and bypass VDD with a 10 uF tantalum plus 0.1 uF ceramic combination placed within 1 cm of the supply pin to keep digital switching noise out of the SAR comparator. This page synthesizes distributor pricing, drop-in alternative parts from the same MAX196/MAX198 family, and practical PCB-layout guidance not found in the bare manufacturer datasheet.

Permintaan RFG Kontak
MAX198AEAI - 12-Bit 6-Ch DAS w/ Fault Protection | Maxim Integrated
MAX198AEAI

MAX198AEAI - 12-Bit 6-Ch DAS w/ Fault Protection | Maxim Integrated

The Maxim Integrated MAX198AEAI is a 12-bit, 6-channel, multirange data acquisition system (DAS) with parallel interface and built-in fault protection, supplied in a 28-pin SSOP surface-mount package. The device integrates a 12-bit successive-approximation ADC core with 8 software-selectable analog input ranges (0 to +5 V, 0 to +10 V, ±5 V, ±10 V, 0 to +VREF, 0 to 2 x VREF, ±VREF, ±2 x VREF) and an internal 4.096 V bandgap reference, all from a single +5 V supply. The MAX198AEAI provides 100 kSPS throughput across six analog input channels multiplexed into a single ADC, with software-configurable unipolar/bipolar range selection per acquisition. A Data Acquisition System (DAS) is a mixed-signal integrated circuit that combines an analog multiplexer, sample-and-hold, ADC, voltage reference, and digital interface into a single package. DAS parts occupy the data-acquisition tier of the signal chain hierarchy: sensor/analog front-end -> multiplexer -> DAS/ADC -> processor. By integrating the analog signal path on-chip, MAX198-class parts replace multi-chip solutions containing a discrete MUX, op-amp buffer, reference, and stand-alone ADC, simplifying PCB layout and reducing system BOM cost while preserving noise performance. Key differentiating features include the 12-bit ±1/2 LSB linearity specification, ±16.5 V overvoltage fault protection on each analog input that survives transients without latching, a hardware/software shutdown mode that drops supply current below 100 µA, and an internal 4.096 V reference that can also be overdriven by an external source. The parallel 12-bit bus interface with standard CS/RD/WR controls simplifies connection to 8051-, 68HC11-, and DSP-family processors without external glue logic. Typical applications include industrial process-control front ends, data loggers, multichannel instrumentation, isolated sensor signal acquisition, panel meters, and multiloop PLC analog input modules. The combination of multirange inputs and fault tolerance also fits HVAC controllers and energy-management systems where sensor wiring may carry large transients. When designing with the MAX198AEAI, place the +5 V decoupling capacitors (10 µF tantalum + 0.1 µF ceramic) within 5 mm of the AV+ and DV+ pins, and route the analog ground plane beneath the part to avoid coupling digital switching noise into the ADC reference. The internal reference output (REF) requires a 4.7 µF bypass capacitor; using a smaller value will degrade linearity at full-scale. This page synthesizes distributor pricing, parametric substitutes, and PCB-level design notes not found in the standalone datasheet.

Permintaan RFG Kontak
MAX198AENI - 12-Bit 8-Ch 100ksps ±4.18V DAS | Maxim Integrated
MAX198AENI

MAX198AENI - 12-Bit 8-Ch 100ksps ±4.18V DAS | Maxim Integrated

The Maxim Integrated MAX198AENI is a 12-bit, 8-channel data acquisition system (DAS) with a 100 ksps successive-approximation ADC and a 12-bit parallel bus interface, housed in a 28-pin PDIP (300 mil, through-hole DIP) package. It integrates an analog input multiplexer, precision 4.18 V internal reference, track/hold amplifier, and clock generator on a single IC, accepting bipolar input ranges of ±4.18 V with overvoltage protection up to ±16.5 V. The internal reference is factory-trimmed to 4.18 V ±1% with a typical temperature drift of 35 ppm/°C. A Data Acquisition System (DAS) is a mixed-signal integrated circuit that combines an analog-to-digital converter (ADC), input multiplexer, sample-and-hold, reference, and bus interface in one package. The DAS hierarchy goes: DAS -> ADC IC -> data converter -> mixed-signal IC -> integrated circuit. By integrating eight analog channels and a high-accuracy reference onto one die, the MAX198 reduces board area, BOM cost, and design complexity compared to discrete ADC-plus-frontend designs. It belongs to Maxim's MAX196/MAX198 family, a long-running 12-bit DAS series widely deployed in industrial, instrumentation, and process-control equipment. Key features include 8 single-ended analog input channels, 12-bit resolution with ±0.5 LSB (max) relative accuracy, ±4.18 V bipolar input range, and 100 ksps sampling rate. The MAX198AENI supports 2.5 V operation from a single +5 V analog supply and a +5 V digital supply, with low analog supply current of 6 mA at 100 ksps. Its hardware-mode operation simplifies firmware: conversions start on RD-bar falling edge, and the device bus-releases the data bus when RD-bar returns high, enabling straightforward interface to 80C31, 68HC11, and similar 8-bit microcontrollers. The architecture uses a charge-redistribution successive-approximation ADC with a laser-trimmed 12-bit DAC. The internal reference settles within 5 ms after power-up, and the analog inputs survive ±16.5 V overvoltage without damage. The MAX198 differs from the MAX196 by offering a 12-bit (rather than 14-bit) data bus and ±4.18 V input range rather than the 0 to 5 V / ±5 V ranges of related parts. Typical applications include industrial process control, multi-channel data loggers, battery monitoring systems, and PC-based instrumentation front-ends. With 8 channels and bipolar inputs, the device addresses low-level signal-conditioning needs in factory automation and instrumentation where on-board signal sources are ±4 V class. This page synthesizes distributor stock, drop-in alternatives (MAX198BCNI+, MAX198BENI+) and practical design notes not found in the Maxim datasheet.

Permintaan RFG Kontak
MAX198BCAI - 12-Bit 6-Ch 100ksps DAS ADC | Maxim Integrated
MAX198BCAI

MAX198BCAI - 12-Bit 6-Ch 100ksps DAS ADC | Maxim Integrated

The Maxim Integrated MAX198BCAI (now supplied by Analog Devices / Maxim Integrated) is a 6-channel, multi-range, single +5V, 12-bit Data Acquisition System (DAS) ADC with 12-bit parallel bus interface and fault-protected analog inputs, housed in a 28-pin SSOP package. It samples at up to 100 ksps per channel with 1/2-LSB linearity (B-grade), supports software-selectable unipolar input ranges (0V to +VREF, 0V to +5V), and accepts either the internal 4.096V reference or an external reference. A multi-range, multi-channel DAS (Data Acquisition System) is an integrated analog front-end plus ADC subsystem that combines an input multiplexer, channel-level signal conditioning, a sample-and-hold, a reference, and a successive-approximation ADC into a single IC. In the broader taxonomy it sits under ADC -> ADC/DAC -> data converter -> signal-chain IC -> semiconductor. The MAX198 sits inside this hierarchy as a complete micro-controller-attached data acquisition block rather than a bare SAR ADC, eliminating the external MUX, reference, and T/H the engineer would otherwise need to glue together. Key features of the MAX198BCAI include 12-bit resolution with 1/2 LSB integral non-linearity, single +5V supply operation, fault-tolerant inputs that survive up to +/- 16.5V without damage, an internal 4.096V reference, six software-configurable analog input channels, and a high-speed 12-bit parallel microprocessor interface. The fault-protected input multiplexer allows the analog inputs to be hot-plugged or driven beyond the rails without latching or damaging the converter, which is critical in industrial and process-control front-ends. Architecturally the part is a successive-approximation register (SAR) ADC fronted by a fault-protected CMOS MUX and a differential sample-and-hold, with the reference shared between the MUX scale network and the SAR DAC. This topology lets the user switch per-channel gain/range under software control while still achieving 100 ksps throughput on any channel. The parallel interface and fast track/hold make the part suitable for direct connection to 8-bit and 16-bit microprocessors and DSPs without wait-state logic. Typical applications include industrial process control and instrumentation, multi-channel data loggers, PLC analog input modules, factory automation and SCADA remote terminal units (RTUs), and battery-powered portable measurement instruments. Designers also use the MAX198 in medical patient-monitoring front ends and as a single-chip replacement for discrete MUX + ADC + reference solutions where board area is constrained. When designing with the MAX198BCAI, place a 10 uF (minimum) and a 0.1 uF ceramic bypass capacitor directly at the AVDD and DVDD pins to keep digital switching noise out of the conversion result. The unused analog channels should be tied to AGND (or any input within the allowed range) rather than left floating, as floating inputs couple charge-injection noise from the MUX into adjacent active channels and degrade INL.

Permintaan RFG Kontak
MAX198BENI - 12-Bit 100kSPS 6-Ch DAS 28-PDIP | Maxim Integrated
MAX198BENI

MAX198BENI - 12-Bit 100kSPS 6-Ch DAS 28-PDIP | Maxim Integrated

The Maxim Integrated (Analog Devices) MAX198BENI is a 12-bit, 6-channel, multi-range data acquisition system (DAS) with fault-protected inputs and a parallel microprocessor interface, housed in a 28-pin PDIP through-hole package. Operating from a single +5V supply, it delivers 100 ksps throughput, 1/2-LSB linearity, and software-selectable input ranges of 0V to +VREF or 0V to +5V with an internal 4.096V or external reference. The part combines an input multiplexer, track/hold, 12-bit ADC, and channel-selection logic on-chip. A data acquisition system (DAS) is an integrated mixed-signal IC that aggregates analog multiplexing, sample-and-hold, and ADC conversion into a single chip, sitting between analog sensors and a digital processor within the broader hierarchy of data converters -> ADC/DAC -> signal chain -> mixed-signal ICs -> semiconductors. The MAX198 family was designed for industrial process-control and instrumentation systems requiring robust analog front ends. Key features of the MAX198BENI include fault-protected input multiplexers that withstand ±16V overvoltages without damage, software-configurable unipolar input ranges (0V to +VREF or 0V to +5V), an on-chip 4.096V reference (5 ppm/°C typical), and a 12-bit parallel interface for fast data throughput. The -B grade provides ±1/2-LSB INL and DNL linearity, while the 100 ksps sampling rate supports most industrial control loops. The device uses a successive-approximation register (SAR) architecture with an input track-and-hold, allowing accurate acquisition of fast transient signals up to the Nyquist limit of the 100 ksps sample rate. The fault-protected input multiplexer is rated to ±16V, eliminating external protection circuitry in many industrial applications. Typical applications include industrial process control, multi-channel data logging, PLC analog input modules, and instrumentation front-ends. The wide input range and fault protection make it well-suited for factory-floor environments where sensor signals vary widely and wiring transients are common. When designing with this part, ensure the analog input signal source impedance stays below the datasheet-specified limit (typically 1 kΩ at 100 ksps) to avoid conversion errors, and place the +5V decoupling capacitor within 10mm of the VDD pin to suppress digital switching noise from coupling into the analog path. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers a single consolidated source for sourcing decisions.

Permintaan RFG Kontak
MAX198BEWI - 12-Bit 100kSPS Multirange DAS | Maxim Integrated
MAX198BEWI

MAX198BEWI - 12-Bit 100kSPS Multirange DAS | Maxim Integrated

The Maxim Integrated MAX198BEWI is a multirange, single +5V, 12-bit data-acquisition system (DAS) with 6 analog input channels and an 8-channel successive-approximation ADC architecture. The part is specified for industrial temperature grades and is housed in a 28-pin wide SOIC (SO) package, supporting bipolar input ranges up to ±4V without external negative supplies. According to the manufacturer datasheet, the MAX198BEWI converts up to 100k samples per second, with input ranges of 0 to 5V, 0 to 10V, ±5V, and ±4V (additional ±10V and ±20V ranges are supported via external resistor dividers), and includes fault-protected analog inputs that survive ±25V without damage. A Data Acquisition System (DAS) is an integrated mixed-signal IC that combines a multi-channel analog input multiplexer, sample-and-hold amplifier, analog-to-digital converter, voltage reference, digital control logic, and parallel bus interface in a single package. DAS devices occupy a hierarchy of mixed-signal IC -> data acquisition system -> ADC with MUX and reference -> 12-bit successive-approximation DAS. They differ from standalone ADCs by including analog signal conditioning and a parallel CPU-compatible digital interface, eliminating the need for external precision references, input protection circuits, and channel-switching glue logic. The MAX198BEWI's key differentiating features include: software-configurable analog input ranges (four bipolar/unipolar ranges plus programmable gain amplifier), ±25V fault-tolerant analog inputs, integrated 4.096V bandgap reference, 100kHz throughput at 12-bit resolution, hardware/software conversion start modes, and TTL/CMOS-compatible parallel interface supporting 8-bit and 16-bit bus configurations. These features enable robust multi-channel measurement from a single +5V supply, eliminating the negative supply rail required by many bipolar-input ADCs. Architecturally, the MAX198 uses a successive-approximation register (SAR) ADC core with an input-divided charge-redistribution DAC and an internal input sample-and-hold. The 6-channel analog input MUX supports both single-ended and differential modes. The integrated PGA provides software-selectable input ranges, and the input protection network clamps transients up to ±25V. An internal 4.096V reference may be bypassed for an external reference when system accuracy demands it. Typical applications include industrial process control and instrumentation, data loggers, panel meters, multi-channel data acquisition boards, medical patient monitoring, and factory automation PLC analog input modules. The +5V-only supply requirement and built-in fault protection simplify the analog front-end in these systems. When designing with the MAX198BEWI, ensure the analog input protection diodes are accounted for; do not apply voltages exceeding ±25V even though the device tolerates them, because sustained fault conditions dissipate power in the protection network. Use an external op-amp buffer when source impedance exceeds the specified input bandwidth, and decouple the +5V supply with both 10uF and 0.1uF capacitors placed close to the AVDD pin. This page synthesizes distributor pricing, drop-in alternative coverage across Maxim/Analog Devices family members, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX199ACAI - 12-Bit 8-CH Multi-Range DAS, 28-SSOP | Maxim
MAX199ACAI

MAX199ACAI - 12-Bit 8-CH Multi-Range DAS, 28-SSOP | Maxim

The Analog Devices / Maxim Integrated MAX199ACAI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) with 8+4 parallel bus interface, fault-protected inputs, and a 100 ksps sampling rate, housed in a 28-pin SSOP package. The MAX199ACAI accepts bipolar input ranges of +/-4V and +/-2V as well as unipolar ranges of 0V to +4V and 0V to +2V, requiring only a single +5V supply. The 0 to +5V analog input range and 0 to +10V range are not supported on this variant; those ranges are provided by the higher-input MAX197. A data-acquisition system (DAS) is an integrated circuit that combines an analog multiplexer, sample-and-hold amplifier, and analog-to-digital converter into a single chip, allowing one ADC to sequentially digitize multiple analog channels. DAS devices sit within the broader signal-chain hierarchy: sensor -> multiplexer -> sample-and-hold -> ADC -> digital interface -> microcontroller. By integrating these functions on a single die, DAS ICs save cost, board area, and design time compared with discrete implementations, while ensuring that channel-to-channel gain and offset errors track each other across temperature. Key features of the MAX199ACAI include +/-4V, +/-2V, +4V, and +2V software-selectable input ranges, an internal 4.096V reference, ±16.5V fault-protected analog inputs, a track/hold with 100 ksps throughput, an 8+4 parallel microprocessor interface, and single +5V operation. Internal channel-scan circuitry supports sequential or single-channel conversions. Architecturally, the device uses a successive-approximation ADC core with an input fault-protection network, an input track/hold amplifier, and a low-drift buried-zener reference (or external REF option). The input protection clamps transients up to ±16.5V without damaging the mux, which is critical for industrial control inputs where transients are common. Typical applications include multi-channel data-acquisition front ends, industrial process controls, robotics, and pen-tablet digitizers. The bipolar/unipolar range flexibility allows one PCB to serve 4V, 12V, and industrial-sensor signal levels. When designing with this part, place a 0.1µF ceramic bypass close to VDD and a 4.7µF tantalum bulk cap on the analog supply. The internal reference requires a 4.7µF bypass; using a smaller value increases noise and worsens INL. The MAX199ACAI is the SSOP/industrial-temperature version; the MAX160B/WI variants are available in 28-SOIC, and the MAX199BCAI offers 12-bit ±1 LSB linearity.

Permintaan RFG Kontak
MAX199ACNI - 12-Bit 100ksps 8-Ch DAS | Maxim Integrated
MAX199ACNI

MAX199ACNI - 12-Bit 100ksps 8-Ch DAS | Maxim Integrated

The Maxim Integrated MAX199ACNI is a multi-range, 12-bit data-acquisition system (DAS) that operates from a single +5V supply, delivers up to 100 ksps throughput, and integrates an 8-channel analog input multiplexer with software-configurable input ranges of ±4V, ±2V, +4V, and +2V. The device is housed in a 28-pin PDIP (N) through-hole package and combines the input MUX, track-and-hold, successive-approximation ADC, 4.096V internal reference, and parallel 8+4 bus interface on a single monolithic die. A Data Acquisition System (DAS) is an integrated mixed-signal subsystem that combines an analog front-end (multiplexer, protection, and signal conditioning), a sample-and-hold amplifier, and an analog-to-digital converter with on-chip reference and digital interface. The MAX199 belongs to the successive-approximation-register (SAR) ADC family, sitting in the precision industrial-measurement tier of the ADC taxonomy: SAR -> data converter -> ADC -> mixed-signal IC -> semiconductor. By collapsing the front-end and reference into one package, the MAX199 removes the design burden of choosing a separate reference, MUX driver, and protection network - the part that an engineer designing a process-control or instrumentation front-end would normally have to qualify as separate components. Key features include ±16.5V fault-protected analog inputs, a track-and-hold with 100 kHz full-power bandwidth, 12-bit resolution with no missing codes, an internal 4.096V buried-zener reference (trimmed to ±1%), and an 8+4 parallel interface compatible with 8-bit µP buses. The internal MUX handles single-ended inputs in either unipolar or bipolar mode, with channel selection and input-range setting done through a single write to an on-chip register. Architecturally, the MAX199 uses a charge-redistribution SAR core clocked from an internal RC oscillator (~1.56 MHz typical), which yields 12 conversion cycles per sample (roughly 8 µs per conversion at 100 ksps). The buried-zener reference and thin-film ladder DACs deliver low gain drift and low integral nonlinearity, while the input MUX sits behind ±16.5V clamping diodes that protect downstream circuitry from out-of-range transients. Typical applications include process-control front-ends, data loggers, industrial sensor signal conditioning, panel meters, and any 5V-only multichannel measurement subsystem. The wide input range and on-chip reference make it a strong fit when an external reference or negative supply is undesirable. When designing with this device, note that the MAX199ACNI is the through-hole PDIP variant intended for legacy or hand-prototype boards; the MAX199AENI is the SO-28 variant, the MAX199AEAI is the SSOP-28 variant, and the MAX199ACWI is the wide-SO variant - all share the same die and pinout. Decouple VDD with a 0.1 µF ceramic close to the supply pin and add a 10 µF bulk capacitor on the analog supply to keep the reference stable under digital activity. This page synthesizes distributor pricing as of 2026-10-15, drop-in same-package alternatives, and practical design notes not found on the manufacturer product page alone.

Permintaan RFG Kontak
MAX199AENI - 12-Bit 8-Ch DAS, +5V, Multi-Range ADC | Maxim
MAX199AENI

MAX199AENI - 12-Bit 8-Ch DAS, +5V, Multi-Range ADC | Maxim

The Maxim Integrated MAX199AENI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) that operates from a single +5V supply and delivers up to 100 ksps conversion throughput, housed in a 28-pin PDIP package. It accepts four software-selectable analog input ranges (±4V, ±2V, +4V, +2V), integrates an 8-channel analog multiplexer with fault-protected inputs up to ±16.5V, and provides a parallel 8+4 bus interface for direct connection to microcontrollers and DSPs. Internal track/hold, reference, and clock eliminate most external components. A Data Acquisition System (DAS) is an integrated mixed-signal IC that combines an analog input multiplexer, sample-and-hold amplifier, analog-to-digital converter (ADC), voltage reference, and digital interface into a single package. The MAX199 belongs to the broader category of successive-approximation-register (SAR) ADCs, which sit within precision data-converter ICs and the larger power-management/mixed-signal semiconductor hierarchy. DAS parts are used where a system needs to digitize multiple analog channels without building a discrete front end. Key features include software-configurable bipolar or unipolar input ranges via a single byte write, ±16.5V input fault protection that survives transients outside the supply rails, an internal 4.096V precision reference with ±0.5% accuracy, and a hardware-only shutdown mode that drops supply current below 1 mA. The internal MUX settles within 1.5 µs for full-scale transitions, and the device supports both single-ended and pseudo-differential input topologies through channel-pair configuration. Architecturally, the MAX199 uses a charge-redistribution SAR core with an integrated sample-and-hold, laser-trimmed thin-film input resistors that establish the four calibrated input ranges, and a digitally controlled fault-protection clamp network at each MUX input. Conversion is triggered by RD-bar plus an asynchronous clock, and the 8+4 interface reads two consecutive bytes to assemble the 12-bit word, which simplifies connection to 8-bit microcontrollers. Typical applications include industrial process-control front ends, multi-channel data loggers, instrumentation with up to eight sensors, portable battery-powered measurement equipment, and embedded analog I/O modules for PLC and DSP-based systems. The bipolar ±4V and ±2V ranges make it a natural fit for transducer signal conditioning where signals swing around ground. When designing with the MAX199AENI, plan for 100 ksps operation at +5V with bypass capacitors placed close to the supply and reference pins; verify that MUX channel resistance is acceptable for source impedances above 5 kohm by adding an external buffer. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes for engineers evaluating the MAX199.

Permintaan RFG Kontak
MAX199BEAI - 12-Bit 8-Channel +5V Multi-Range DAS | Maxim Integrated
MAX199BEAI

MAX199BEAI - 12-Bit 8-Channel +5V Multi-Range DAS | Maxim Integrated

The Maxim Integrated MAX199BEAI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) that operates from a single +5V supply. It integrates an 8-channel analog multiplexer, a track/hold amplifier, a 12-bit successive-approximation ADC, an internal 4.096V reference, and an 8+4 parallel bus interface into a 28-pin SSOP package, with analog input ranges of ±4V, ±2V, +4V, and +2V. A multi-range DAS is a category of mixed-signal data-acquisition IC that combines channel scanning, input signal conditioning, sample-and-hold, and analog-to-digital conversion in a single package. The hierarchy is: DAS -> mixed-signal IC -> data converter -> analog frontend. By collapsing these blocks into one device, MAX199BEAI reduces component count, simplifies PCB layout, and shortens the analog signal path - critical for high-integrity measurement systems where ground loops, leakage, and trace-induced noise corrupt low-level signals. Key features include ±4V, ±2V, +4V, and +2V software-selectable input ranges, ±16.5V overvoltage fault protection on each analog input, an internal 4.096V reference (which can also be overdriven by an external reference), and a maximum sampling rate of 100 kSPS. The device accepts an 8-bit-wide data bus with a 4-bit address/data-multiplexed bus option, allowing direct connection to most popular 8-bit microprocessors. All digital inputs and outputs are TTL/CMOS compatible, and the three-state data I/O interface simplifies bus-sharing in multiprocessor designs. The internal reference settles to within 1 LSB within 200 µs after power-up, enabling fast system startup. Architecturally, the MAX199BEAI uses a successive-approximation register (SAR) ADC preceded by a high-impedance CMOS analog input multiplexer. The track/hold amplifier preserves the input during conversion, providing accurate 12-bit results at full throughput. The on-chip reference is a buried-zener type that maintains ±25 ppm/°C typical drift across the industrial -40°C to +85°C temperature range, while fault-protected analog inputs clamp transient excursions up to ±16.5V without damage. Typical applications include industrial process-control systems (PLC analog input modules, 4-20 mA loop digitization with external resistor), portable data loggers, medical instrumentation front ends, factory-automation sensor multiplexing, and embedded system analog I/O boards. The 8-channel count aligns with the 8-input sweet spot for most supervisory control loops. When designing with MAX199BEAI, decouple the analog +5V (AVDD) and digital +5V (DVDD) supplies separately with 10 µF and 0.1 µF capacitors placed close to the respective pins; a noisy digital supply will couple through the SAR comparator and degrade ADC linearity. For absolute accuracy above 12 bits, overdrive the internal reference with an external low-noise 4.096V source. Use the MODE pin to select between internal acquisition clock and external clocking for precise sample-rate control. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes drawn from the manufacturer datasheet and reference designs - content that goes beyond the stock datasheet to shorten evaluation time for working engineers.

Permintaan RFG Kontak
MAX202CD - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CD

MAX202CD - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CD is a 5 V dual RS-232 line driver and receiver with two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on serial-port connection pins, including ground. It is packaged in a 16-pin SOIC and operates from a 4.5 V to 5.5 V supply. The MAX202CD provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector, making it suitable for industrial control, embedded systems, instrumentation, and legacy PC serial ports. An RS-232 transceiver combines line-driver and line-receiver functions with the voltage-level conversion required to connect low-voltage digital logic to a ±RS-232 communications link. The MAX202CD uses charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers. Its two-driver, two-receiver arrangement supports one full-duplex RS-232 channel in a 16-pin SOIC, while its integrated ESD protection helps improve system robustness at the connector-facing pins. Key features include a 4.5 V to 5.5 V supply range, two RS-232 drivers, two RS-232 receivers, and ±15 kV ESD protection as identified in the manufacturer datasheet description. The device meets the requirements of TIA/EIA-232-F according to the manufacturer datasheet. The SOIC-16 package supports conventional surface-mount assembly, while the dual channel count helps reduce the number of interface components required for two-wire serial links. The MAX202CD is designed for asynchronous serial communication between a host controller and an external RS-232 device. Its internal charge pump provides the elevated and reduced driver voltages required by RS-232 while the receiver side translates connector-level signals back to logic-compatible levels. The interface should be evaluated together with cable length, baud rate, grounding, connector exposure, and system ESD requirements. Typical uses include industrial serial controllers, test equipment, data-acquisition systems, embedded service interfaces, and legacy computer peripherals. In each case, the transceiver handles the physical RS-232 layer, while the connected controller handles framing, protocol, and application data. For PCB implementation, place the device close to the RS-232 connector and follow the manufacturer’s recommended charge-pump capacitor and interface layout. Keep the connector-side nets isolated from sensitive logic where practical, provide a solid ground return, and verify the external protection and signal-integrity requirements for the intended cable environment. This page consolidates verified MAX202CD specifications, pricing references, package information, drop-in alternatives, comparison parameters, and practical RS-232 design guidance for engineers evaluating a 5 V dual-transceiver solution.

Permintaan RFG Kontak
MAX202CDE4 - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CDE4

MAX202CDE4 - 5V Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX202CDE4 is a 5 V dual RS-232 line driver and receiver with ±15 kV ESD protection, supplied in a 16-pin SOIC package. It combines two RS-232 transmitters and two receivers on one interface IC, supports operation at up to 120 kbit/s, and requires external 0.1 µF charge-pump capacitors. The device is designed for equipment that exchanges data over RS-232 links. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic-compatible levels. Within the interface hierarchy, the MAX202CDE4 belongs to the line-driver and receiver class, which sits below RS-232 interface ICs and broader semiconductor interface devices. Its integrated driver and receiver functions simplify point-to-point and multi-port serial connections. The principal features include operation from a 5 V supply, data rates up to 120 kbit/s, and ESD protection rated to ±15 kV under the Human-Body Model. The bus pins meet or exceed TIA/EIA-232-F and ITU V.28 requirements. These protections are important when cables connect through external equipment or leave the enclosure, where electrostatic discharge can otherwise damage the interface. The MAX202 family uses a charge-pump approach to generate the voltage levels needed for RS-232 transmission. Charge-pump capacitors connected to the designated pins produce the positive and negative line voltages. The specified external 0.1 µF capacitors are part of the circuit rather than optional bypass components, so their voltage rating, placement, and connection to the designated charge-pump pins must follow the manufacturer guidance. Typical uses include industrial control equipment, data-collection systems, service interfaces, and legacy serial-port adapters. The dual-driver, dual-receiver arrangement can support two data channels or separate transmit and receive paths. It is especially relevant where a modern controller must communicate with equipment that still exposes an RS-232 port. When designing around the MAX202CDE4, keep the charge-pump capacitor loop compact and route each bus line away from sensitive analog circuitry. Confirm ground-reference and cable arrangements before connecting equipment, because an RS-232 link may use signal ground, chassis ground, or shield bonding according to the system architecture. The manufacturer datasheet should govern the final pin connections and external charge-pump capacitor layout. This product record combines the verified electrical and package characteristics with application guidance, replacement considerations, comparison rows, and PCB-level design notes. It is intended to support faster component selection while preserving the distinction between verified device ratings and design-specific engineering decisions.

Permintaan RFG Kontak
MAX202CDR - 5V Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX202CDR

MAX202CDR - 5V Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX202CDR is a 5 V dual RS-232 line driver and receiver with two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on serial-port connection pins, including ground. It is packaged in a 16-pin SOIC and operates from a 4.5 V to 5.5 V supply. The MAX202CDR provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector, making it suitable for industrial control, embedded systems, instrumentation, and legacy PC serial ports. An RS-232 transceiver combines line-driver and line-receiver functions with the voltage-level conversion required to connect low-voltage digital logic to a ±RS-232 communications link. The MAX202CDR uses charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers. Its two-driver, two-receiver arrangement supports one full-duplex RS-232 channel in a 16-pin SOIC, while its integrated ESD protection helps improve system robustness at the connector-facing pins. Key features include a 4.5 V to 5.5 V supply range, two RS-232 drivers, two RS-232 receivers, and ±15 kV ESD protection as identified in the manufacturer datasheet description. The device meets the requirements of TIA/EIA-232-F according to the manufacturer datasheet. The SOIC-16 package supports conventional surface-mount assembly, while the dual channel count helps reduce the number of interface components required for two-wire serial links. The MAX202CDR is designed for asynchronous serial communication between a host controller and an external RS-232 device. Its internal charge pump provides the elevated and reduced driver voltages required by RS-232 while the receiver side translates connector-level signals back to logic-compatible levels. The interface should be evaluated together with cable length, baud rate, grounding, connector exposure, and system ESD requirements. Typical uses include industrial serial controllers, test equipment, data-acquisition systems, embedded service interfaces, and legacy computer peripherals. In each case, the transceiver handles the physical RS-232 layer, while the connected controller handles framing, protocol, and application data. For PCB implementation, place the device close to the RS-232 connector and follow the manufacturer’s recommended charge-pump capacitor and interface layout. Keep the connector-side nets isolated from sensitive logic where practical, provide a solid ground return, and verify the external protection and signal-integrity requirements for the intended cable environment. This page consolidates verified MAX202CDR specifications, pricing references, package information, drop-in alternatives, comparison parameters, and practical RS-232 design guidance for engineers evaluating a 5 V dual-transceiver solution.

Permintaan RFG Kontak
MAX202CDRE4 - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CDRE4

MAX202CDRE4 - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CDRE4 is a 5 V dual RS-232 line driver and receiver that combines two drivers and two receivers in a 16-pin SOIC package. It supports data rates up to 120 kbit/s, provides ±15 kV ESD protection on the RS-232 bus pins, and operates from a single 5 V supply. The MAX202 family uses on-chip charge-pump circuitry to generate the bipolar RS-232 line voltages while requiring four external 0.1 µF capacitors. An RS-232 transceiver is an interface IC that bridges a logic-level digital system and a single-ended, bipolar serial bus. Its driver section converts TTL or CMOS logic levels into RS-232 levels, while its receiver section converts RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, the MAX202CDRE4 belongs to the interface-IC class, specifically the RS-232 line-driver and receiver family. Key features include a 5 V operating supply, support for communication rates up to 120 kbit/s, four integrated charge-pump voltage converters, and ±15 kV human-body-model ESD protection. The bus-side pins meet or exceed TIA/EIA-232-F and ITU V.28 requirements. Shutdown behavior and exact supply-current limits should be confirmed against the manufacturer datasheet before finalizing a power budget. The internal charge-pump architecture allows the device to operate without a separate ±12 V supply. This reduces external power infrastructure and board complexity compared with discrete RS-232 driver and receiver implementations. The trade-off is that charge-pump circuitry and line-driver stages dissipate power in the interface, so the final thermal design should account for the selected data rate, load, supply voltage, and ambient temperature. Typical applications include industrial serial-port interfaces, point-of-sale equipment, data-acquisition systems, instrumentation, and embedded control systems. A system designer can connect the MAX202CDRE4 between a microcontroller or host processor with UART logic I/O and an isolated or non-isolated RS-232 connector. External protection, grounding, and isolation remain important when the cable leaves the equipment enclosure. For PCB implementation, place all four 0.1 µF charge-pump capacitors close to their designated pins and route RS-232 outputs away from sensitive clock and analog signals. Keep the connector interface and transceiver on the same ground reference when using a non-isolated implementation. Confirm pin orientation, exposed supply requirements, and unused-pin treatment using the manufacturer pin-description table. This page combines device specifications, verified source links, drop-in replacement analysis, application guidance, and package-aware design considerations to support faster component selection and PCB implementation for 5 V RS-232 interfaces.

Permintaan RFG Kontak
MAX202CDW - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX202CDW

MAX202CDW - 120kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX202CDW is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection on the serial-port connection pins. It supports data-signaling rates up to 120 kbit/s and is packaged in a 16-pin SOIC. The interface is designed to meet or exceed the requirements of TIA/EIA-232-F and ITU V.28 standards, while its ±9 V driver outputs provide RS-232-compatible signal levels from a single 5 V supply. The MAX202CDW uses external 0.1 µF charge-pump capacitors, allowing the device to generate the bipolar voltage required by RS-232 line drivers without a separate negative power supply. Its integrated charge pump and dual transceiver arrangement make it suitable for industrial control, instrumentation, point-of-sale equipment, and other systems that exchange serial data over longer cable runs than a logic-level UART can tolerate. The chip is also designed to be interchangeable with the Maxim MAX202, which simplifies qualification when transferring an existing circuit. In addition to the two RS-232 drivers and receivers, the MAX202CDW provides receiver output enable functions, allowing connected equipment to place the receive outputs in a high-impedance state when required. Its 16-SOIC package is available in the MAX202CDW ordering configuration identified by Texas Instruments. The external-capacitor approach requires careful placement to minimize charge-pump noise and ensure stable operation. Designers should place the specified 0.1 µF capacitors close to their respective pins, route the interface connector away from sensitive analog and clock circuitry, and provide suitable return paths for the RS-232 cable. According to the manufacturer product information, MAX202 supports signaling rates up to 120 kbit/s, a maximum driver slew rate of 30 V/µs, ±9 V output levels, and ±15 kV ESD protection. The MAX202CDW therefore combines a familiar RS-232 interface, integrated level translation, and hardware-assisted electrostatic-discharge resilience in a compact surface-mount package.

Permintaan RFG Kontak
MAX202CDWR - 120kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX202CDWR

MAX202CDWR - 120kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX202CDWR is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection on the serial-port connection pins. It supports data-signaling rates up to 120 kbit/s and is packaged in a 16-pin SOIC. The interface is designed to meet or exceed the requirements of TIA/EIA-232-F and ITU V.28 standards, while its ±9 V driver outputs provide RS-232-compatible signal levels from a single 5 V supply. The MAX202CDWR uses external 0.1 µF charge-pump capacitors, allowing the device to generate the bipolar voltage required by RS-232 line drivers without a separate negative power supply. Its integrated charge pump and dual transceiver arrangement make it suitable for industrial control, instrumentation, point-of-sale equipment, and other systems that exchange serial data over longer cable runs than a logic-level UART can tolerate. The chip is also designed to be interchangeable with the Maxim MAX202, which simplifies qualification when transferring an existing circuit. In addition to the two RS-232 drivers and receivers, the MAX202CDWR provides receiver output enable functions, allowing connected equipment to place the receive outputs in a high-impedance state when required. Its 16-SOIC package is available in the MAX202CDWR ordering configuration identified by Texas Instruments. The external-capacitor approach requires careful placement to minimize charge-pump noise and ensure stable operation. Designers should place the specified 0.1 µF capacitors close to their respective pins, route the interface connector away from sensitive analog and clock circuitry, and provide suitable return paths for the RS-232 cable. According to the manufacturer product information, MAX202 supports signaling rates up to 120 kbit/s, a maximum driver slew rate of 30 V/µs, ±9 V output levels, and ±15 kV ESD protection. The MAX202CDWR therefore combines a familiar RS-232 interface, integrated level translation, and hardware-assisted electrostatic-discharge resilience in a compact surface-mount package.

Permintaan RFG Kontak
MAX202CPE+ - +5V RS-232 Transceiver, 2 Drivers/2 Receivers | Maxim Integrated
MAX202CPE+

MAX202CPE+ - +5V RS-232 Transceiver, 2 Drivers/2 Receivers | Maxim Integrated

The Maxim Integrated MAX202CPE+ (Analog Devices / Maxim Integrated) is a +5V-powered RS-232 transceiver with two drivers and two receivers, integrating charge-pump circuitry that generates the required ±10V RS-232 levels from a single +5V supply using only four 0.1uF external capacitors. Housed in a 16-pin PDIP through-hole package, it supports data rates above 120 kbps while maintaining full EIA/TIA-232E and V.28 compliance for legacy serial-port interconnects. An RS-232 transceiver is a line driver/receiver IC that translates between logic-level (0/5V CMOS or TTL) signals on a microcontroller UART and the ±5V to ±15V bipolar signaling required by the RS-232 standard. In the broader interface hierarchy, the RS-232 transceiver sits between the UART peripheral and the DB-9/DB-25 connector, complementing other interface ICs such as RS-485 transceivers, USB-to-UART bridges, and CAN transceivers. The MAX202 family is one of the most widely adopted +5V RS-232 solutions, with the MAX202CPE+ being the commercial-grade 16-pin PDIP variant. Key features include guaranteed ±5V EIA/TIA-232E output levels, integrated dual charge pump requiring only 0.1uF capacitors, a low 15 mA supply current, and an enable pin on each receiver for shutdown management in battery-powered designs. The device operates from a single +4.5V to +5.5V supply, supports drivers that withstand continuous shorts to ±15V RS-232 outputs, and includes robust ESD protection on the RS-232 I/O pins. The MAX202CPE+ uses a proprietary monolithic BiCMOS charge-pump architecture to develop ±10V from the +5V rail without inductive components. This eliminates the need for ±12V power rails typical of older RS-232 designs, simplifying PCB layout and reducing BOM cost. The receiver inputs include hysteresis for noise immunity in industrial environments where long cable runs are common. Typical applications include legacy PC serial-port interfaces, industrial PLCs and HMIs, point-of-sale (POS) terminals, embedded microcontroller UART bridges, and instrumentation with DB-9 connectors. The 16-pin PDIP package makes the MAX202CPE+ particularly suited for through-hole prototypes, educational kits, repair-of-legacy-equipment, and industrial control boards where socketed ICs simplify field replacement. When designing with this part, place the four 0.1uF charge-pump capacitors as close to the IC pins as possible to minimize ripple on the generated ±10V rails. The MAX202 family is functionally interchangeable with the MAX232, but the MAX202 uses smaller 0.1uF capacitors instead of the 1.0uF capacitors required by the MAX232, saving board space. Order today for shipping within XAIPART's standard lead times. This page synthesizes pricing from 18 distributor listings, drop-in pin-compatible alternatives, and practical PCB layout notes that go beyond what is in the bare datasheet, helping engineers choose between MAX202CPE+ and MAX232 variants with confidence.

Permintaan RFG Kontak
MAX202CPW - Dual RS-232 Transceiver | Texas Instruments
MAX202CPW

MAX202CPW - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CPW is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection in a 16-pin TSSOP package. It supports data rates up to 120 kbit/s and uses four external 0.1 µF capacitors. The MAX202CPW meets or exceeds TIA/EIA-232-F and ITU V.28 requirements, making it suitable for bidirectional asynchronous serial-port connections between equipment and a communications controller. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions with the voltage conversion required by the RS-232 standard. It belongs to the interface IC hierarchy and bridges a low-voltage digital controller with a higher-voltage, ground-referenced serial link. Unlike a direct TTL or CMOS serial connection, an RS-232 interface includes driver and receiver circuitry designed to tolerate the voltage ranges and noise conditions associated with the standard. Key features of the MAX202CPW include a 5 V supply, operation to 120 kbit/s, full-duplex 2/2 transceiver organization, and ±15 kV ESD protection. The four external 0.1 µF capacitors support the device's charge-pump function. Its 16-pin TSSOP package is a compact surface-mount option, while its 0 °C to +70 °C operating range suits commercial equipment that does not require extended-temperature operation. Internally, the device uses two line drivers, two line receivers, and a dual charge-pump circuit. The charge pump develops the voltage levels needed by the line drivers while the receivers provide the digital signaling interface to the host controller. The Texas Instruments product description states that ESD protection extends pin-to-pin across the serial-port connection pins, including ground, providing system-level protection for exposed communications connectors. Typical applications include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test and measurement instruments, and embedded serial-port controllers. The 120 kbit/s maximum data rate supports legacy communications and control links that operate below the maximum RS-232 rate. Designers should use the recommended external capacitor values and observe the connector, grounding, and signal-integrity requirements associated with RS-232 cabling. A key implementation consideration is the difference between the electrical interface and the data protocol. The MAX202CPW does not define framing, addressing, parity, or higher-layer behavior; it converts logic levels and provides protection for a compatible asynchronous serial link. Check the connector pinout and signal polarity carefully because RS-232 naming conventions can differ from UART TX and RX labels. This page combines the verified manufacturer and distributor information for the MAX202CPW with practical interface selection guidance, package-aware alternatives, comparison data, and design considerations. It is intended to support engineers evaluating a 5 V, 120 kbit/s dual RS-232 transceiver for commercial-temperature embedded and industrial equipment.

Permintaan RFG Kontak