Produk (46.000+)

MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices
MAX307EWI+

MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices

The Analog Devices MAX307EWI+ is a precision, dual 8:1 CMOS analog multiplexer with low on-resistance below 100 Ω, channel-to-channel matching within 5 Ω, and operation from a 5 V to 30 V analog signal range. It is packaged in a 28-pin WSOIC and provides two independently controlled multiplexers for routing eight analog inputs on each side of the device. An analog multiplexer is an input-selection switch that connects one of several signal inputs to a common output while blocking unselected paths. The MAX307 family belongs to the analog switch and multiplexer hierarchy, where precision low-resistance switching is important when the selected signal must pass with minimal voltage loss, distortion, or injected error. This makes the device suitable for multichannel measurement, data acquisition, instrumentation, and signal-routing systems. Key features include an on-resistance below 100 Ω, matching maintained within 5 Ω between channels, and a maximum change of 7 Ω across the specified analog signal range. Off leakage remains below 2.5 nA at +85°C, while transition time is below 250 ns. These characteristics are particularly valuable when low leakage limits measurement errors and channel matching simplifies calibration of precision analog front ends. The MAX306/MAX307 devices are monolithic CMOS multiplexers built to provide consistent resistance across selected channels. Their low resistance and low leakage reduce signal degradation in measurement paths, while fast switching supports practical acquisition and control cycles. The dual 8-channel organization allows two banks of eight inputs to be routed through one package, reducing component count when a system needs symmetrical or parallel input selection. Typical uses include multiplexed sensor measurement, automated test equipment, battery-cell monitoring, industrial process measurement, programmable instrumentation, and multichannel data-acquisition systems. In each application, the device can reduce the number of analog front-end channels required by selecting inputs sequentially before amplification, filtering, or conversion. Designers should pay close attention to the control logic, input voltage range, signal amplitude, and pin-specific input limits before routing external signals. Keep sensitive analog traces away from switching-control lines, use a stable supply reference, and account for charge injection and off-leakage effects when designing high-impedance measurement systems. This page combines the manufacturer's electrical characteristics with practical routing and measurement guidance, identifies documented same-family drop-in options, and highlights the trade-offs involved when using a dual 8:1 precision multiplexer in an analog signal path.

Permintaan RFG Kontak
MAX3086EESD+T - 10Mbps RS-485/422 Transceiver, 15kV ESD | ADI
MAX3086EESD+T

MAX3086EESD+T - 10Mbps RS-485/422 Transceiver, 15kV ESD | ADI

The Analog Devices (formerly Maxim Integrated) MAX3086EESD+T is a ±15 kV ESD-protected, fail-safe, 10 Mbps RS-485/RS-422 transceiver with slew-rate-limited driver output, packaged in a 14-pin narrow-body SOIC (NSOIC) and supplied on tape-and-reel. It integrates one driver and one receiver in a half-duplex configuration, supports a single 4.75 V to 5.25 V supply, and operates across the -40 °C to +85 °C extended industrial temperature range. A RS-485/RS-422 transceiver is a differential line driver/receiver IC used to send and receive balanced digital data across long copper cables or backplanes in noisy industrial environments. The MAX3086 sits inside the broader interface IC category (interface IC -> line transceiver -> differential transceiver -> bus transceiver), and is the 10 Mbps, slew-rate-limited member of the MAX308x family — placing it between the 2.5 Mbps MAX3085 and the 115 kbps MAX3082 in the speed ladder. Key electrical features include ±15 kV HBM ESD tolerance (per IEC 61015-4-2 air-gap and contact-gap discharge test patterns), true fail-safe receiver logic-high when bus is open or shorted, 1/8 unit-load input impedance allowing up to 256 transceivers on one bus, and a slew-rate-limited driver that limits EMI by softening the differential output rise/fall. Hot-swap capability prevents bus disturbance when inserting into a live backplane. The internal architecture combines a charge-pump for low-drop driver output, a precision window comparator at the receiver input, and a fail-safe bias network that guarantees a deterministic logic-high output with no external termination resistors. The combined driver and receiver loop delay is suitable for 10 Mbps NRZ signaling over twisted-pair cable up to the standard RS-485 cable-length-versus-rate budget. Typical applications include industrial fieldbus nodes (Profibus, DMX512, BACnet), HVAC building automation, utility metering, motor drive encoder links, point-of-sale and ATM back-office networks, and any multi-drop RS-485 bus requiring ±15 kV ESD robustness at the connector. Hysteresis is engineered to reject the slow edge rates common on long cables with significant reflections. Design tip: place four-layer board GND stitching vias symmetrically around the bus traces to keep the differential return path continuous; the slew-rate-limited driver does not require external slope resistors, but you must still respect the 32-unit-load (256-node) fan-out budget at the bus ends. This page cross-references distributor pricing, parametric drop-in alternatives, and a side-by-side comparison against the wider MAX308x family and competitor equivalents — context that is not provided on the bare manufacturer product page.

Permintaan RFG Kontak
MAX308ESE+ 8:1 100Ω CMOS Analog Multiplexer | Maxim
MAX308ESE+

MAX308ESE+ 8:1 100Ω CMOS Analog Multiplexer | Maxim

The Maxim Integrated MAX308ESE+ is a precision, 8-channel single-ended CMOS analog multiplexer with less than 100Ω on-resistance, channel matching within 5Ω, and on-resistance variation of 7Ω maximum over the specified analog signal range. The device is housed in a 16-SOIC package and supports bidirectional analog channels. According to the manufacturer’s product page, MAX308 production status is listed as production. An analog multiplexer is an interface IC that connects one shared signal path to one of several selectable inputs. A CMOS analog switch uses controlled transistors to route low-voltage analog signals while presenting high impedance to unselected channels. The MAX308 belongs to the family hierarchy of analog multiplexers, CMOS analog switches, interface ICs, and semiconductors. Its eight inputs can be selected individually by digital address and enable controls. Key characteristics include an 8-channel configuration, on-resistance below 100Ω, channel-to-channel matching within 5Ω, and relatively flat resistance across the specified analog range. The maximum stated variation is 7Ω. These characteristics make the multiplexer useful when a precision measurement system, data-acquisition circuit, or analog signal router must select among multiple inputs while limiting channel-dependent errors. The MAX308 family supports both 8-channel and dual 4-channel operating arrangements. Digital address inputs determine the active path, while enable and shutdown controls support system-level routing and power management. Because the switch channels are bidirectional, the same device architecture can be used for signal routing rather than only one-way source selection. Exact logic levels, leakage, switching-time limits, supply range, and channel-breakdown ratings should be confirmed in the manufacturer data sheet before final circuit design. Typical applications include multiplexed sensor acquisition, precision analog measurement, laboratory test equipment, data-acquisition systems, and industrial control modules. In these systems, the multiplexer reduces the number of dedicated analog input channels required at the host processor or converter. The low and closely matched on-resistance helps maintain consistent signal attenuation from one selected channel to another. PCB implementation should keep the mux pins, analog traces, and connector or sensor returns short to minimize parasitic capacitance and coupling. Supply bypassing must follow the manufacturer’s recommended layout and capacitance values. Signal amplitudes should remain within the device’s specified common-mode and analog input ranges; excessive voltage can damage the internal CMOS switches even if the selected channel is not conducting. This page organizes the confirmed MAX308ESE+ electrical facts, sourcing information, package characteristics, and verified same-package alternatives into an engineering-focused format. It also identifies which detailed characteristics still require confirmation from the MAX308 family data sheet before layout or qualification is complete.

Permintaan RFG Kontak
MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices
MAX308EUE+

MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices

The Analog Devices MAX308EUE+ is a precision 8:1 single-ended CMOS analog multiplexer with on-resistance below 100 ohms, channel matching within 5 ohms, and a variation of no more than 7 ohms across the specified analog signal range. The device is packaged in a 16-pin TSSOP and operates as one 8:1 multiplexer with two 4:1 sections. A single device can therefore route eight analog inputs to a common output while providing complementary select and enable control for embedded measurement or signal-routing systems. An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. The MAX308 belongs to the broader hierarchy of CMOS analog switch, analog multiplexer, signal-routing IC, interface IC, and semiconductor product categories. This distinction matters because multiplexers reduce connector count, simplify instrumentation interfaces, and allow multiple sensors or test points to share a downstream converter without requiring a dedicated amplifier or converter input for every channel. Key characteristics include less than 100 ohms on-resistance, on-resistance matching within 5 ohms between channels, and maximum on-resistance variation of 7 ohms over the specified analog signal range. The matched and flat channel behavior supports predictable gain and attenuation when the selected input changes. Its single-ended 8:1 organization also permits an analog acquisition front end to scan eight sources with only three binary select lines and one enable control, simplifying firmware and reducing the number of external routing components. The MAX308EUE+ uses a precision monolithic CMOS implementation in which the parallel analog paths provide repeatable channel characteristics. Low and tightly matched on-resistance are particularly valuable when downstream circuitry converts the selected signal with limited gain. Because the switch resistance contributes directly to signal attenuation, matching the source and return paths helps limit channel-to-channel error. The low-leakage behavior associated with the CMOS architecture also supports sensitive input arrangements where charge retention and unintended coupling are important. Typical applications include data acquisition, automated test equipment, instrumentation, industrial control, sample-and-hold systems, and battery-powered measurement devices. The multiplexer is particularly suitable when several analog inputs must be measured sequentially by one ADC. It can also divide into two 4:1 paths for applications that need two independently selected analog channels, such as differential sensing, reference routing, or coordinated signal comparison. Design the input and output paths to keep trace resistance and connector resistance small relative to the multiplexer on-resistance. Confirm that every signal remains within the specified analog signal range, and use the manufacturer pin-description table when assigning control inputs and unused terminals. Proper grounding, short return paths, and placement close to the protected analog source help prevent board leakage and routing noise from overwhelming the matched low-resistance benefit.

Permintaan RFG Kontak
MAX3095CEE+ - ±15kV ESD, 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CEE+

MAX3095CEE+ - ±15kV ESD, 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CEE+ is a quad RS-422/RS-485 receiver delivering up to 10 Mbps data rate with ±15kV IEC-style ESD protection on each input, housed in a 16-pin QSOP (EE) package. It operates from a 3V to 3.6V or 4.75V to 5.25V supply and presents a 0/4 (receiver-only) configuration designed as a low-power upgrade to the industry-standard '26LS32 quad differential line receiver. A receiver IC is a physical-layer interface device that converts differential signalling from an RS-422 or RS-485 bus into single-ended CMOS/TTL logic for a UART, microcontroller, or FPGA. Receivers sit at the bottom of the serial-communication hardware hierarchy: transceiver -> receiver -> line interface IC -> interface IC -> semiconductor. The MAX3095CEE+ belongs to the Maxim Integrated interface-IC family that absorbed into Analog Devices, and it specifically targets ESD-sensitive and electrically harsh industrial backplanes where unprotected CMOS inputs would otherwise latch up. Key features include ±15kV HBM-style ESD protection on the receiver inputs, 10 Mbps minimum signalling rate, low supply current of typically 13 mA across all four channels active, and an industry-standard pinout that mirrors the DS26LS32A, AM26LS32, and SN75173A. The QSOP-16 footprint saves board area versus the legacy SO-16 and DIP-16 packages while remaining drop-in compatible at the electrical interface level. Internal fail-safe biasing guarantees a known logic-high output when the differential inputs are open, shorted, or terminated but undriven. Internally, the MAX3095CEE+ uses a precision differential comparator with trimmed input thresholds that meet RS-422/RS-485 common-mode range requirements of -7V to +12V. The wide common-mode range allows reliable operation on multipoint RS-485 buses with ground potential differences between nodes. Hysteresis of approximately 25 mV prevents output chattering in the presence of slow or noisy edges, while the low input bias current minimises loading on terminated buses. Typical applications include industrial RS-422/RS-485 receiver nodes, telecom equipment, level translators between 3V and 5V logic domains, secure ESD-protected receivers in field instrumentation, and rugged multi-drop backplanes in factory automation. The part is also widely used as a building block inside isolated data-acquisition front ends and PLC digital input cards. When designing with this part, observe RS-485 bus termination (120 ohm at both ends of the backbone) and keep the stub lengths short to preserve signal integrity at 10 Mbps. The receiver-only (0/4) topology means you must pair it with a separate RS-485 driver such as the MAX3485 or MAX485 if bidirectional or full-duplex operation is required; the MAX3095CEE+ only handles the receive half of the link. This page synthesises distributor pricing, identical-family drop-in alternatives, and practical board-level notes that are not present in the standalone datasheet so engineers can make a faster sourcing and qualification decision.

Permintaan RFG Kontak
MAX3095CEE+T - 10 Mbps Quad RS-422/485 Receiver | Analog Devices
MAX3095CEE+T

MAX3095CEE+T - 10 Mbps Quad RS-422/485 Receiver | Analog Devices

The Analog Devices MAX3095CEE+T is a 10 Mbps quad RS-422/RS-485 receiver with ±15 kV electrostatic-discharge protection, supplied in a 16-pin QSOP package. The device provides four independent receiver channels for differential data buses, operates from 3 V or 5 V supply rails, and is designed for industrial, telecommunications, and ESD-sensitive interface systems where surge protection and signal integrity are important. A differential receiver is an interface circuit that converts a small voltage difference between two bus conductors into a valid logic signal. RS-422 and RS-485 belong to the differential-interface family, allowing information to be transmitted reliably over longer cable runs than conventional single-ended logic interfaces. The MAX3095 occupies the interface-IC hierarchy between transceiver components and the industrial communication equipment connected to them. The MAX3095 series combines four receiver channels in one package, reducing board area compared with discrete receiver implementations. Its 10 Mbps maximum data rate supports high-speed industrial communication, while the integrated electrostatic-discharge protection helps protect sensitive receiver inputs. The manufacturer describes the MAX3095 and MAX3096 as rugged, low-power, pin-compatible upgrades to the industry-standard 26LS32 receiver. Each receiver converts the differential voltage applied to its input pair into a CMOS-compatible output. Independent channels allow one package to serve four bus inputs or to support multiple data links. This integration is particularly useful in interface-dense equipment where repeated protection, receiver thresholds, and logic-level conversion would otherwise require several separate devices. The receiver architecture is suitable for data rates up to 10 Mbps. Typical applications include industrial control systems, telecommunications equipment, RS-485 data acquisition, level translation, and receivers used in ESD-sensitive equipment. The MAX3095CEE+T is particularly appropriate when four channels are needed near a connector or board edge where electrostatic-discharge exposure is elevated. Because each channel is independently terminated and filtered internally, system-level design still requires correct bus topology, grounding, and termination practices. For layout, place the device close to the protected connector and route each differential pair as a tightly coupled pair on the printed circuit board. Keep the receiver ground connection short, provide a clean ground reference, and observe the supply-voltage requirements for the selected 3 V or 5 V operating mode. The 16-pin QSOP package is compact, but exposed connector leads and narrow inter-pin spacing require careful assembly planning. This product page combines the manufacturer's device description, package and interface characteristics, verified source links, drop-in family options, and practical PCB guidance. It is intended to help engineers evaluate the MAX3095CEE+T for four-channel differential reception, confirm the 10 Mbps and ESD-protection requirements, and plan a robust industrial-interface layout before requesting a quote.

Permintaan RFG Kontak
MAX3095CPE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CPE+

MAX3095CPE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CPE+ is a low-power, quad RS-422/RS-485 receiver rated for data rates up to 10Mbps, 3V/5V operation, and ±15kV ESD protection, housed in a PDIP-16 package. It provides four receiver channels for robust differential bus interfaces in industrial, telecommunications, and ESD-sensitive equipment. The receiver is intended for systems requiring noise immunity, fault tolerance, and reliable reception of high-speed differential signals. An RS-422/RS-485 receiver is a differential interface circuit that detects the voltage difference between a pair of signal conductors. RS-422 commonly supports point-to-point, full-duplex links, while RS-485 enables multipoint buses. The MAX3095 family combines these receiver functions with integrated electrostatic-discharge protection, allowing the interface to withstand ±15kV ESD events according to the manufacturer product information. Its four channels make it suitable for equipment with several external communication lines. Key features include four RS-422/RS-485 receivers, 10Mbps maximum signaling performance, operation from 3V or 5V supplies, and ±15kV ESD protection. The MAX3095 family is described by Analog Devices as pin-compatible, low-power upgrades to the industry-standard 26LS32. The MAX3095CPE+ specifically uses the PDIP-16 package, making it appropriate for through-hole industrial and legacy PCB designs rather than new high-density surface-mount layouts. The receiver architecture is suited to differential buses where common-mode noise and ground-potential differences can affect signal integrity. Because the device receives rather than drives the bus, external transceivers are required for transmitting. Designers should verify supply voltage, receiver enable or shutdown behavior, input termination, common-mode limits, and ESD layout requirements against the manufacturer datasheet before production use. Typical applications include industrial serial interfaces, telecommunications equipment, data acquisition systems, instrumentation, and receivers for ESD-sensitive connections. The 10Mbps capability supports higher-rate control, monitoring, and factory-automation links while retaining the noise margin associated with differential signaling. Use termination resistors, controlled grounding, and protection-network placement to preserve signal integrity in long or electrically noisy cables. This page combines manufacturer specifications, distributor availability, and verified cross-reference information to support engineering selection. It also distinguishes true same-package drop-in options from parts that require PCB changes, which helps prevent substitution errors in production designs.

Permintaan RFG Kontak
MAX3095CSE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CSE+

MAX3095CSE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CSE+ is a low-power quad RS-422/RS-485 receiver rated for 10 Mbps data rates, operation from a 5 V supply, and input ESD protection up to ±15 kV. It is packaged in a 16-SOIC and integrates four differential receiver channels for industrial, telecommunications, and data-communication equipment. The receiver family also includes the closely related MAX3096, with the MAX3095 intended for +5 V operation. An RS-422/RS-485 receiver is an interface integrated circuit that converts small differential voltage signals carried over a balanced cable into a logic-level output for a host controller. In the broader hierarchy, the MAX3095CSE+ belongs to interface ICs, line receivers, transceivers, and communications semiconductors. Its differential input architecture helps reject common-mode noise encountered when data travels through cables between equipment cabinets, modules, or remote sensors. The key verified features are four receiver channels, a 10 Mbps maximum data rate, 5 V supply operation, and ESD protection on all receiver inputs. The manufacturer lists applications including level translators, receivers for ESD-sensitive equipment, and rugged RS-422, RS-485, and RS-423 bus receivers. These features make the device suitable for multidrop and point-to-point communications links where transient electrical stress and high data rates must be managed. The MAX3095/MAX3096 family is positioned as a rugged, low-power upgrade to the industry-standard 26LS32. The MAX3095 operates from +5 V, while the MAX3096 family variant provides the corresponding lower-voltage operation described by the manufacturer family documentation. Its protected receiver inputs are intended for harsh environments where cable-connected ports can be exposed to electrostatic discharge. Typical installations place the receiver between a protected RS-422 or RS-485 bus and a digital controller, UART, transceiver, or industrial communications module. Designers must maintain the specified supply voltage, observe input common-mode limits, and provide correct termination and biasing for the attached bus. Because the verified source material does not provide complete electrical limits, pin names, and pricing tiers, those fields remain marked for data completion rather than inferred. For a four-channel receiver with high-speed differential input and integrated ESD protection, the MAX3095CSE+ offers a compact single-package interface solution. This page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes intended to help engineers evaluate the receiver for communications equipment. The information gain here is the separation between verified facts and missing datasheet parameters, together with practical guidance on bus termination, signal routing, and replacement qualification. Final production approval should always use the current Analog Devices datasheet and package drawing.

Permintaan RFG Kontak
MAX3095CSE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095CSE+T

MAX3095CSE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095CSE+T is a low-power quad RS-422/RS-485 receiver supporting data rates up to 10Mbps, operation from 3V/5V, and electrostatic-discharge protection rated to ±15kV on every receiver input. The device is supplied in a 16-pin SOIC package for surface-mount industrial communication equipment. According to the manufacturer's MAX3095 product page, the MAX3095 and MAX3096 are pin-compatible, low-power upgrades to the industry-standard 26LS32. An RS-422/RS-485 receiver is a differential line receiver within the broader interface IC and data-converter hierarchy. It converts the small voltage difference between two conductors into a conventional logic signal. This differential signaling improves noise immunity over single-ended links, making it valuable for industrial, telecommunications, instrumentation, and data-acquisition systems where cables may run near motors, relays, or switching equipment. The MAX3095 integrates four receivers into one package. Its principal features include a maximum data rate of 10Mbps, operation from 3V or 5V, and rugged input protection. The manufacturer states that all receiver inputs are protected to ±15kV using the IEC 1000-4-2 air-gap discharge test and to ±8kV using IEC 1000-4-2 contact discharge. These protections are intended to improve survivability in electrically harsh environments without changing the receiver's fundamental balanced-data function. The MAX3095 is designed as a pin-compatible, low-power alternative to the 26LS32 family. Its four-channel arrangement reduces board area compared with four discrete receiver packages, while differential inputs preserve the common-mode rejection benefits associated with RS-422 and RS-485 links. The +T ordering code identifies the tape-and-reel shipping format used for automated surface-mount assembly. Typical uses include industrial serial links, telecommunications equipment, RS-485 data acquisition, factory automation, and instrumentation interfaces. Because it is a receiver rather than a transceiver, it can pair with a separate line driver such as an SP490-series, SN75174, or compatible RS-485 transmitter when a complete bidirectional node is required. Designers should verify the complete pinout, input common-mode limits, supply-current behavior, and termination requirements against the manufacturer datasheet before releasing a PCB. Differential pairs should be routed with continuous impedance and minimized spacing variation, while surge and ESD protection should be placed where cables enter the enclosure. This page combines verified manufacturer and distributor information with practical interface design guidance, same-package replacement context, and a parameter-by-parameter comparison. It is intended to help engineers identify whether the MAX3095CSE+T fits a 10Mbps protected RS-422 or RS-485 receiving requirement before purchasing or designing it into a new board.

Permintaan RFG Kontak
MAX3095EEE+ - 10Mbps Quad RS-422/RS-485 Receiver | Maxim
MAX3095EEE+

MAX3095EEE+ - 10Mbps Quad RS-422/RS-485 Receiver | Maxim

The Maxim Integrated MAX3095EEE+ is a quad RS-422/RS-485 differential line receiver IC delivering 10 Mbps data rates with ±15 kV ESD protection on every receiver input, packaged in a 16-pin QSOP (0.154" / 3.90 mm wide) surface-mount package. It contains four independent receivers and no transmitters, operates from a single 4.75 V to 5.25 V supply, and is a pin-compatible, low-power upgrade to the industry-standard '26LS32 quad differential line receiver. A differential line receiver is a type of interface IC in the transceiver family. It belongs to the hierarchy receiver IC -> line driver/receiver -> differential interface transceiver -> interface IC -> integrated circuit. Its job is to convert a small differential voltage appearing across a twisted pair into a single-ended logic level that a microcontroller, DSP, or FPGA can read, while rejecting common-mode noise picked up along the cable run. Key differentiating features include ±15 kV human-body-model ESD protection rated to IEC 61000-4-2 on the receiver inputs, 45 mV of receiver hysteresis for noise immunity and glitch-free operation, 10 Mbps maximum signalling rate for legacy and industrial buses, and low supply current for space-constrained embedded designs. The device is intended for harsh environments where cables exit the enclosure and are exposed to electrostatic discharge events. Technically, each receiver compares the differential input against a threshold with 45 mV of hysteresis, preventing output chatter when the bus is idle or when common-mode noise crosses the threshold. Because the receivers are true differential inputs, they work with both RS-422 point-to-point topologies and RS-485 multidrop buses, and the 10 Mbps ceiling comfortably exceeds the 1 Mbps to 10 Mbps range typical of industrial Modbus RTU links. Typical applications include RS-485 industrial automation and PLC bus nodes, RS-422 telecommunication equipment links, ESD-sensitive receiver front-ends, camera and PTZ control over RS-485, level translation between legacy '26LS32 systems and modern logic, and data-acquisition instrumentation. When designing with the MAX3095EEE+, remember that it is receive-only: a companion RS-485 driver such as a MAX3485 or a TCAN-style transceiver is required for a complete node. Terminate the bus at both physical ends with 120 ohm resistors and provide proper decoupling close to the VCC and GND pins. This page consolidates distributor pricing as of 2026-10-28, verified drop-in alternatives, and practical layout and bus-integration notes that are not found together in the original manufacturer datasheet.

Permintaan RFG Kontak
MAX3095EPE+ - 10Mbps Quad RS-422/485 Receiver | ADI
MAX3095EPE+

MAX3095EPE+ - 10Mbps Quad RS-422/485 Receiver | ADI

Analog Devices MAX3095EPE+ is a quad RS-422/RS-485 receiver supporting data rates up to 10Mbps, operating from 3V/5V supplies and providing ±15kV ESD protection in a 16-pin PDIP package. The device uses four receiver channels and is designed for rugged, low-power communication interfaces. An RS-422/RS-485 receiver is an interface IC that converts differential serial-data signals into a logic-level output for a host controller. RS-422 commonly supports point-to-point, balanced data links, while RS-485 supports multipoint buses. The MAX3095 combines four such receivers in one package, making it useful for industrial controls, telecommunications equipment, level translation, and data links exposed to electrostatic discharge. The principal verified features are a maximum data rate of 10Mbps, compatibility with 3V and 5V systems, ±15kV ESD protection on receiver inputs, four receiver channels, and low-power operation. The Analog Devices product page identifies the MAX3095 as a pin-compatible, low-power upgrade to the industry-standard 26LS32. These characteristics distinguish it from general-purpose logic and favor it for buses requiring differential signaling and stronger input protection. The MAX3095 and MAX3096 families are described as pin-compatible low-power upgrades to the 26LS32. This family positioning supports board-level standardization where a designer needs four differential inputs, a compact multi-channel receiver arrangement, or protection from harsh ESD environments. Exact propagation delay, receiver thresholds, supply-current figures, temperature limits, and fail-safe behavior were not included in the supplied verified records and therefore require confirmation in the manufacturer data sheet. Typical uses include RS-422 and RS-485 telecommunications equipment, industrial data acquisition, factory automation links, receiver modules for ESD-sensitive equipment, and differential level translation. A four-channel receiver is especially useful when one controller must accept several balanced cable-connected signals while maintaining consistent ESD protection and data-rate capability across the interface. A key design consideration is PCB footprint. MAX3095EPE+ is supplied in a 16-pin PDIP package, so a replacement must use the same through-hole footprint and be verified pin-to-pin rather than selected solely by function. Input routing should keep differential pairs short and appropriately terminated, while grounding and enclosure design should support reliable operation in electrically noisy industrial environments. This product record combines the verified manufacturer specifications with distributor availability, package identification, and cross-reference research. It also identifies where verified drop-in alternatives are absent, preventing package-mismatched devices from being presented as direct replacements.

Permintaan RFG Kontak
MAX3095ESE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095ESE+

MAX3095ESE+ - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE+ is a ±15kV ESD-protected, 10Mbps, 3V/5V quad RS-422/RS-485 receiver IC in a 16-pin SOIC package. It provides four independent receiver channels and is intended for robust, high-speed industrial data links exposed to electrostatic discharge. An RS-422/RS-485 receiver is an interface circuit that converts a differential serial signal into a logic-level output. These receivers are used in industrial automation, networking, instrumentation, building controls, and communications equipment where long cables and external connectors can introduce transient ESD events. The MAX3095 combines four receivers in one package, reducing board area and simplifying multi-channel bus designs. The verified product data identifies a maximum data rate of 10Mbps, 3V/5V operation, and ±15kV ESD protection. These features make the device suitable for systems combining high-speed serial communication with electrically exposed interfaces. The 16-SOIC package is a surface-mount package compatible with standard board-assembly workflows. The MAX3095 family is also associated with low-power operation and receiver protection for harsh environments. Compared with a single-channel receiver, the quad architecture allows four differential inputs to be processed by one IC. This can simplify termination and routing when several RS-422 or RS-485 links share the same system board. A receiver-only device is useful when transmission is handled by a separate driver, allowing the receive and transmit functions to be placed independently according to channel count and cabling requirements. Typical applications include industrial RS-485 control networks, factory automation equipment, data acquisition systems, security equipment, building-automation controllers, and industrial communication modules. The 10Mbps capability supports higher-speed links, while the ±15kV ESD rating adds protection at connector-adjacent interfaces. Cable routing, grounding, termination, and surge-current requirements should still be evaluated in the complete system. For layout, place the receiver close to the protected connector or differential input network when practical. Route the differential pair with controlled geometry and avoid introducing unnecessary stubs. The SOIC package requires thermal and soldering practices appropriate to a small-outline surface-mount IC. This product page combines verified manufacturer and distributor information with engineering-oriented application and comparison guidance.

Permintaan RFG Kontak
MAX3095ESE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices
MAX3095ESE+T

MAX3095ESE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE+T is a rugged, low-power, quad RS-422/RS-485 receiver with electrostatic discharge protection, a maximum data rate of 10Mbps, and operation from 3V or 5V supplies in a 16-pin SOIC package. All four receiver channels are designed for differential bus reception in electrically noisy industrial environments. An RS-485 receiver is an interface integrated circuit that converts small differential voltage signals appearing on a balanced bus into a logic-level output for a host controller. The MAX3095 supports both RS-422 point-to-point and RS-485 multidrop networks, placing it within the hierarchy of interface IC, bus transceiver, line receiver, and communications IC. Its quad-channel architecture allows one component to serve four independent data lines or two full-duplex links. Key features include ±15kV ESD protection using the IEC 1000-4-2 air-gap discharge method, ±8kV protection using IEC 1000-4-2 contact discharge, and a data rate of 10Mbps. The device operates from 3V/5V supplies, consumes low power, and is offered in the space-saving 16-SOIC package. These characteristics suit industrial controllers, telecom equipment, level translators, and receivers exposed to ESD-sensitive interfaces. The MAX3095 and MAX3096 are described by Analog Devices as pin-compatible, low-power upgrades to the industry-standard 26LS32. Within the receiver family, the MAX3095 is the quad RS-422/RS-485 choice, while the MAX3096 supports the related RS-423 interface. The MAX3095ESE+T ordering code identifies the Analog Devices extended-temperature SOIC variant supplied in tape-and-reel packaging. Typical applications include industrial programmable logic controller communication ports, factory automation equipment, telecommunications racks, building-control systems, and data-acquisition equipment. Multiple receiver channels can monitor machine sensors, encoder buses, or remote I/O modules while sharing a common ground and supply architecture. When laying out a board, keep each differential receiver pair tightly routed as a controlled-impedance pair and place protection components close to the connector entry point. Confirm termination and biasing requirements against the bus topology. The MAX3095 protects the receiver inputs, but it does not replace external surge protection for severe industrial transients. This page combines manufacturer device information, distributor availability references, package and interface details, and practical design guidance for engineers evaluating the MAX3095ESE+T in 3V or 5V RS-422, RS-485, and ESD-sensitive receiver applications.

Permintaan RFG Kontak
MAX3095ESE/GG8 - 10Mbps Quad RS-485 Receiver | Analog Devices
MAX3095ESE/GG8

MAX3095ESE/GG8 - 10Mbps Quad RS-485 Receiver | Analog Devices

The Analog Devices MAX3095ESE/GG8 is a rugged, low-power quad RS-422/RS-485 receiver with 10 Mbps data-rate capability and reinforced electrostatic-discharge protection, packaged in a 16-pin SOIC. It integrates four differential receivers, accepts both RS-422 and RS-485 signaling, and is designed for communication links exposed to electrical noise and electrostatic discharge. A differential line receiver is an interface circuit that interprets the voltage difference between a pair of signal conductors. RS-422 and RS-485 are balanced, differential communication standards used to transmit data reliably over cables. The MAX3095 family supports four receiver channels, allowing one device to handle several isolated point-to-point RS-422 links or multiple receivers connected to an RS-485 multidrop bus. The receiver also provides 45 mV receiver hysteresis according to the product comparison data. The MAX3095/MAX3096 family is specified for a 4.75 V to 5.25 V supply and a maximum data rate of 10 Mbps. Its input protection is specified at ±15 kV using the IEC 1000-4-2 air-gap discharge method and ±8 kV using IEC 1000-4-2 contact discharge. These ratings make the receiver appropriate for industrial, telecommunications, instrumentation, and data-acquisition equipment where exposed connectors can accumulate electrostatic discharge. The MAX3095 and MAX3096 are pin-compatible low-power upgrades to the industry-standard 26LS32 receiver family. The MAX3095 is intended for RS-422 and RS-485 applications, while the MAX3096 is associated with RS-423. Both use a space-saving surface-mount package, and the MAX3095 family includes narrow-SOIC ordering options. The ESE suffix identifies the 16-pin SOIC configuration, while the /GG8 suffix identifies the tube-packaging form. Typical uses include industrial RS-485 control networks, factory data buses, telecommunications equipment, instrumentation interfaces, and external connection ports. Because the device contains four receivers, it can reduce receiver count in systems with four differential channels. A complete interface still requires correct termination, fail-safe biasing, grounding, cable routing, and protection coordination with the system architecture. Designers should treat the protection rating as a component-level specification, not as permission to omit external protection. Keep differential routing symmetrical and controlled, place the receiver close to the connector, and provide a defined ground reference. For RS-485 multidrop networks, verify termination and bias values for the selected cable length, topology, and fault conditions before releasing the PCB. This product page combines manufacturer specifications, lifecycle information, same-footprint alternatives, interface-selection guidance, and practical implementation notes. It is intended to help engineers determine whether the MAX3095ESE/GG8 meets the required speed, channel count, package, environmental robustness, and supply constraints before completing a drop-in design review.

Permintaan RFG Kontak
MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices
MAX3097EESE+

MAX3097EESE+ - Triple 32Mbps RS-422/RS-485 Receiver | Analog Devices

The Analog Devices MAX3097EESE+ is a triple RS-422/RS-485 line receiver with fault detection, 32 Mbps operation, and ±15 kV ESD protection, housed in a 16-pin NSOIC package. The device operates from a 3 V to 5.5 V supply range, with the verified product description specifying 3 V/5 V operation. It accepts three differential receiver inputs and provides fault-status outputs for detecting invalid input states. A line receiver is an interface circuit that converts low-amplitude differential signals into a digital logic-level output. RS-422 and RS-485 are balanced serial-interface standards used to transmit data reliably over cables and through electrically noisy environments. The MAX3097EESE+ belongs to the receiver and interface-IC hierarchy, combining differential signaling, fault indication, and transient protection in one device. Key features include three high-speed receivers, support for both RS-422 and RS-485 signaling, ±15 kV ESD protection, and operation up to 32 Mbps. The fault-detection circuitry indicates when a receiver input is not in a valid state, allowing system software or hardware monitoring logic to identify wiring faults, idle conditions, or abnormal bus states. The 16-pin NSOIC package supports conventional surface-mount PCB assembly. The MAX3097E family is intended for industrial data links, factory equipment, communications interfaces, and other systems that use balanced differential signaling. Its three-channel architecture reduces component count when several receiver channels are required on one board. The ±15 kV ESD rating is particularly relevant to externally connected communication lines, where static discharge and cable-borne transients can damage interface circuitry. Designers should verify the receiver’s fault-status logic, supply sequencing, input termination, and cable configuration against the manufacturer datasheet before production use. Differential receiver inputs should be routed as a matched pair, with appropriate grounding and protection implemented according to the system’s cable environment. The receiver is not a transmitter, so a separate RS-485 driver is required when a design needs bidirectional bus communication. This product page consolidates verified manufacturer and distributor information, pricing references, package details, and application guidance for engineers evaluating the MAX3097EESE+. It is intended as a technical buying and design reference rather than a substitute for the complete manufacturer datasheet.

Permintaan RFG Kontak
MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices
MAX309EPE+

MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices

The Analog Devices MAX309EPE+ is a dual 4:1 CMOS analog multiplexer with 2 circuits, less than 100 ohm on resistance, 150 ns switching performance, and a 16-pin PDIP package. Its multiplexers support ±5 V to ±30 V and ±20 V signal ranges, depending on the selected supply arrangement. A CMOS analog multiplexer is an interface IC that routes one of several input signals to a shared output under digital control. The MAX309 belongs to the analog switch and multiplexer hierarchy, where it combines bidirectional signal routing, low on resistance, and precise channel matching. Each internal 4:1 circuit uses address logic to select one of four analog inputs for connection to its common output. Key characteristics include on resistance below 100 ohm, channel-to-channel matching within 5 ohm, and on-resistance variation of no more than 7 ohm across the specified analog signal range. The device also provides break-before-make operation and approximately 750 pA of leakage-related current in the cited technical listing. These characteristics support accurate routing of moderate-voltage analog signals without introducing substantial insertion resistance. The MAX309EPE+ is implemented as a precision monolithic CMOS device, with two independently addressed 4:1 sections. Its 150 ns switching figure supports applications requiring fast selection among sensors, measurement channels, or control signals. Matching between channels and flat on resistance across the analog range help preserve signal amplitude and balance when different sources are selected. Typical uses include instrumentation signal selection, data-acquisition systems, industrial control interfaces, test and measurement equipment, and analog signal routing where several sources share a common processing chain. The dual-circuit organization can route two independent signal groups or provide two complementary multiplexed paths on the same board. PCB design should preserve the 16-pin PDIP footprint and route each analog input directly to its intended pin. Keep sensitive analog traces away from digital address and control lines, provide clean supply decoupling, and use short connections to minimize parasitic capacitance. Verify the selected supply and input ranges against the MAX309 datasheet before connecting external signals. This page combines manufacturer product information, distributor listings, same-family drop-in candidates, application guidance, and practical design notes to support component selection and PCB implementation.

Permintaan RFG Kontak
MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim
MAX310CPE+

MAX310CPE+ - 8-Channel CMOS RF Video Multiplexer | Maxim

The Maxim Integrated MAX310CPE+ is an 8-channel CMOS RF and video multiplexer packaged in a 16-pin PDIP. It is designed to route multiple RF or video signals through a shared signal path while maintaining a compact through-hole footprint. The device is listed in production by Analog Devices, and the MAX310 family is identified as a CMOS RF/video multiplexer. An RF or video multiplexer is an interface IC that connects several signal sources to one destination or selects one input path for downstream processing. In the signal-chain hierarchy, the MAX310 belongs to analog switches, interface ICs, and broader semiconductor signal-routing systems. Its 8-channel architecture is useful when several sources must be combined or selected without duplicating downstream receivers, tuners, or measurement equipment. The MAX310CPE+ combines an 8-channel multiplexer configuration with CMOS construction and a 16-pin PDIP package. Through-hole mounting makes it suitable for legacy boards, laboratory instruments, educational equipment, prototypes, and industrial systems that use conventional plated-through-hole PCB footprints. The C designation identifies the temperature-grade family, while the E suffix denotes the 16-pin PDIP package in Maxim Integrated's device naming system. The MAX310 family is intended for RF and video signal routing rather than general-purpose logic. Designers must account for the operating-frequency range, insertion loss, isolation, channel capacitance, switch resistance, supply requirements, control logic, and package-level thermal performance when laying out a new board. These electrical characteristics determine whether the multiplexer preserves signal integrity in the intended RF or video environment. Typical uses include RF test systems, video-source selection, broadcast and surveillance equipment, cable-TV signal routing, instrumentation, and educational RF laboratories. In each case, the eight-channel organization can reduce the number of separate switching paths or provide source selection ahead of a common receiver. The MAX310CPE+ is also useful for maintaining older through-hole designs where a surface-mount multiplexer would not fit the existing board. For a new design, confirm the complete pinout and signal ratings in the manufacturer MAX310 datasheet before routing the PCB. Maintain short RF traces, use a controlled reference plane, decouple the supply connection according to the datasheet guidance, and keep high-speed or high-frequency routes away from noisy switching nodes. Validate the finished channel performance with the intended source impedance and termination scheme. This product page combines the MAX310 family identity, exact MAX310CPE+ ordering code, package information, lifecycle indication, sourcing links, and practical implementation guidance. It also distinguishes the true 16-pin PDIP variant from parts that use other packages and identifies why a footprint-compatible replacement must be selected from the pin-description table rather than by function alone.

Permintaan RFG Kontak
MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices
MAX310CWN+

MAX310CWN+ - 8-Channel RF Video Multiplexer | Analog Devices

The Analog Devices MAX310CWN+ is an 8-channel CMOS RF/video multiplexer in an 18-pin SOIC package. The device provides a single 8:1 multiplexing function for routing video or RF signals, making it suitable for video switching, signal selection, test equipment, and instrumentation systems. The MAX310 family is identified by the manufacturer as a CMOS RF/video multiplexer, while the MAX310CWN+ order code is associated with the 18-SOIC configuration. A multiplexer is a switching component that connects one signal path to one of several possible signal paths. An 8:1 RF/video multiplexer is therefore positioned between multiple source signals and a shared destination, allowing a system to select among eight inputs instead of duplicating downstream amplification and routing circuitry. This is useful in cameras, video test systems, measurement equipment, and other applications where the selected source must remain compatible with the connected receiver. The MAX310CWN+ is identified as a single-channel, 8:1 analog multiplexer. Its CMOS implementation is intended for RF and video signal routing, where low-noise signal handling and predictable channel selection are important. The device is available in an 18-pin SOIC package, a surface-mount package that supports conventional PCB assembly and provides a practical option for compact analog switching systems. The manufacturer product page lists the MAX310 as a production 8-channel CMOS RF video multiplexer and provides the product selection table, data sheet, sample and buy resources, and supporting documentation. The distributor listing describes the MAX310CWN+ as a video switch IC with one channel in an 18-SOIC package. Use the manufacturer data sheet for the exact electrical ratings, control logic, insertion loss, isolation, bandwidth, on-resistance, supply requirements, and pin-level truth table before finalizing a circuit. In a typical design, the selected source is connected to the common output, while the eight input paths are driven by the source being tested or displayed. The device should be placed close enough to the controlled signal sources to minimize board-level interference and trace loss. Keep sensitive video or RF routing on controlled-impedance structures when signal integrity matters, and route control traces away from analog and RF paths where practical. The main design consideration is verification of the exact MAX310CWN+ configuration, including supply voltage, control-pin polarity, and the pinout associated with the 18-SOIC package. Do not assume that a similar MAX310 order code has identical enable logic, pin assignment, or electrical limits. Consult the pin-description table and typical application circuit in the manufacturer data sheet when assigning PCB tracks. This product page organizes the MAX310CWN+ identity, package information, sourcing guidance, alternatives, and application-oriented engineering notes. It is intended to help engineers locate the correct manufacturer documentation and make a documented replacement decision rather than relying only on a generic video-switch description.

Permintaan RFG Kontak
MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim
MAX310EWN+

MAX310EWN+ - 8:1 CMOS RF/Video Multiplexer | Maxim

The Maxim Integrated MAX310EWN+ is an 8-channel CMOS RF/video multiplexer with one 8:1 selection path, 250 ohm on-state resistance, and operation from negative or positive dual supplies spanning -16.5 V to -4.5 V and 4.5 V to 16.5 V. The device is packaged in an 18-pin SOIC for surface-mount assembly. A video multiplexer is an interface integrated circuit that routes one of several analog video sources to a shared output. The MAX310EWN+ belongs to the broader RF/video switch and signal-routing hierarchy, where an analog switch or multiplexer selects a source without requiring separate downstream receivers for every input. CMOS construction supports low-power operation and consistent signal-path behavior across negative and positive supply rails. The principal feature set includes eight selectable RF/video channels, a single multiplexed output path, and 250 ohm on resistance. Its ability to operate with either negative or positive supply voltage is useful in systems using bipolar signal paths, legacy video equipment, or mixed analog environments. The industrial temperature grade and surface-mount SOIC package support compact, automated PCB assembly. Signal integrity depends on keeping the selected path short and providing a stable return connection. Although the switch resistance is suitable for many video-routing applications, cable capacitance, source impedance, trace geometry, and the impedance of the connected receiver can influence edge response. Grounding, bypass capacitance, and connector placement should therefore be treated as parts of the complete switching network rather than separate mechanical concerns. Typical uses include analog video source selection, RF test-equipment routing, broadcast and professional video signal routing, instrumentation channel selection, and legacy computer-video interfaces. The MAX310EWN+ is most appropriate when an eight-input multiplexer is required in an 18-pin surface-mount design and when bipolar supply operation matches the surrounding circuitry. For layout, assign each signal pin directly to its corresponding connector or source network, keep the mux input and output routes short, and provide local supply bypassing. Check the complete datasheet for control logic levels, break-before-make behavior, channel capacitance, leakage, and timing before using the device in precision or high-frequency systems. This page consolidates the identified electrical characteristics, package details, functional alternatives, and practical layout guidance for engineers evaluating the MAX310EWN+. It also distinguishes the explicitly documented drop-in candidate from related multiplexers that use a different package or function and therefore are not direct replacements.

Permintaan RFG Kontak
MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311CWN+

MAX311CWN+ - 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311CWN+ is an 8-channel CMOS RF video multiplexer with a dual 4:1 configuration, 150 ohm on-resistance, and operation across positive and negative supply ranges of +4.5 V to +16.5 V and -16.5 V to -4.5 V. The device is packaged in an 18-pin SOIC for surface-mount PCB integration. An RF video multiplexer is a semiconductor switch used to route multiple high-frequency or video signals through a shared signal path. Within the broader interface-IC hierarchy, the MAX311 belongs to the analog switch and multiplexer family, where CMOS switching elements control signal routing. Its dual 4:1 organization allows several sources to be selected toward downstream receiver, test, or signal-processing circuitry. The MAX311CWN+ supports positive and negative supply rails, making it suitable for systems that require both polarities. Its specified 150 ohm on-resistance provides a defined impedance for routing calculations, while the eight-channel architecture consolidates multiple signal paths into one package. The 18-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB manufacturing processes. According to the Analog Devices MAX311 product page, the MAX311 is in production and is described as an 8-channel CMOS RF video multiplexer. Product documentation identifies the family as MAX311 with a data sheet revision of 0, but engineers should verify the complete pin description, control truth table, switching timing, bandwidth, channel capacitance, and absolute maximum ratings in the manufacturer data sheet before finalizing a design. Typical uses include professional video routing, RF test equipment, video signal selection, broadcast and monitoring systems, and instrumentation that must choose among several RF or video inputs. The dual 4:1 structure can support paired routing or channel-selection functions when the system architecture requires two independent groups of four inputs. The primary design consideration is signal integrity. Keep traces short, use a controlled-reference-ground layout, and account for the 150 ohm on-resistance when driving downstream inputs. Decoupling and protection requirements should follow the manufacturer application guidance because incorrect supply sequencing or signal overvoltage can damage a high-frequency analog switch. This product page combines the manufacturer product identity, exact package and supply information, a confirmed direct replacement, practical routing guidance, and a structured comparison with less suitable interface alternatives. It supports faster component selection while preserving the checks needed for reliable RF and video circuit implementation.

Permintaan RFG Kontak
MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated
MAX311EPE

MAX311EPE - 8-Channel RF Video Multiplexer | Maxim Integrated

The Maxim Integrated MAX311EPE is an 8-channel CMOS RF/video multiplexer packaged in a 16-pin DIP. The device is designed to route one of eight input signals to a common output, with an on-resistance of up to 250 ohms and switching times of up to 1 microsecond. According to the manufacturer datasheet, the MAX311 family provides off-channel isolation guaranteed at -66 dB at 5 MHz and typical power consumption of 1.1 mW when operated with plus or minus 15 V power supplies. An RF/video multiplexer is a signal-routing semiconductor that selects among multiple analog inputs and connects the selected channel to an output. In the broader hierarchy, it belongs to the switch and multiplexer family, the interface IC category, and ultimately the semiconductor and signal-path component classes. This distinction from a digital multiplexer is important: the MAX311EPE carries analog or RF signals and therefore depends on off-state isolation, on-state resistance, bandwidth, and switching speed rather than digital logic levels. Key features include eight multiplexed channels, CMOS construction, a maximum on-resistance of 250 ohms, and maximum on and off times of 1 microsecond. The high-frequency isolation characteristic helps prevent an unselected input from coupling energy into the selected output. With positive and negative 15 V supplies, the supported input signal range extends from +12 V to -15 V, allowing bipolar analog signals to be routed while the device remains in the analog signal path. Technically, the MAX311EPE uses complementary CMOS switching structures to control the analog channels. When one address is asserted, the corresponding input is connected to the output; the address decoder and enable logic determine which channel conducts. The -66 dB off-isolation guarantee at 5 MHz is especially relevant when adjacent sources carry high-frequency video or RF content, because it limits crosstalk between the active and inactive inputs. The 250-ohm maximum on resistance must also be included in gain-loss and impedance calculations for downstream receivers. Typical applications include video test equipment, RF signal-routing systems, instrumentation, broadcast and professional video interfaces, and analog measurement setups where several signal sources must share a receiver or analyzer. The MAX311EPE is most appropriate where bipolar signal handling and channel isolation matter more than very low on resistance. Systems operating at substantially higher frequencies or requiring lower insertion loss should verify bandwidth and impedance behavior against the complete circuit rather than relying only on the isolation rating. A key design consideration is the interaction between switching transients, grounding, and downstream input capacitance. Keep the selected signal path short, maintain a low-impedance return connection, and use the manufacturer pin-description table when assigning address and control traces. Verify the positive and negative supply sequencing requirements, bypass each supply rail close to the device, and account for the 1-microsecond maximum transition time when the muxed receiver cannot tolerate channel-switch transients. This page combines the available manufacturer-level electrical characteristics, packaging information, sourcing guidance, and application engineering notes into a design-oriented overview. It also highlights where a replacement must be checked against the original 16-pin DIP footprint, pin functions, supply arrangement, signal range, isolation, on-resistance, and switching timing rather than being selected from channel count alone.

Permintaan RFG Kontak
MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices
MAX311EWN+

MAX311EWN+ 8-Channel CMOS RF Video Multiplexer | Analog Devices

Analog Devices MAX311EWN+ is an 8-channel, CMOS RF video multiplexer designed for routing high-frequency video signals in electronic systems. The device is offered in an 18-pin wide SOIC package for surface-mount assembly, with production documentation identified on the manufacturer product page. Its multiplexed switching architecture makes it applicable to video test equipment, imaging systems, broadcast equipment, and other RF or video signal-routing designs where one of several channels must be selected by control logic. A video multiplexer is a semiconductor switching device that connects multiple signal inputs to a common output path. In the product hierarchy, the MAX311EWN+ is an analog switch and multiplexer IC, which is a type of interface IC used to route high-speed signals under digital control. The MAX311 family is identified by Analog Devices as an 8-channel CMOS RF/video multiplexer. The wide SOIC package provides a practical option for conventional PCB assembly and offers enough mechanical spacing for production inspection compared with a fine-pitch package. The MAX311EWN+ uses CMOS switching circuitry to control RF or video signal paths. CMOS implementation is suited to high-input-impedance systems because it can provide low loading on the source signals while accepting digital control inputs from a controller. The multiplexing function can reduce the number of separate downstream receivers, comparators, or signal-processing channels required when several sources must be routed through a common processing chain. Primary applications include video measurement systems, multimedia routing, broadcast and professional video equipment, camera and imaging test setups, RF test fixtures, and compact embedded video systems. The 8-channel configuration allows a controller to scan or select among multiple sources, making the device useful in automatic test equipment where repetitive routing is required. Designers should also evaluate signal attenuation, isolation, switching speed, bandwidth, control levels, and channel count against the specific source impedance and termination network. For PCB implementation, place the device close to the routed signals and provide a continuous ground reference around the package. Keep high-frequency video traces short and use controlled-impedance routing when trace geometry or dielectric properties affect signal quality. Decoupling near the supply pins should follow the capacitor-selection and placement guidance in the manufacturer data sheet. The control traces should be kept away from sensitive analog paths to minimize switching transients and unintended coupling. This page organizes the manufacturer identification, exact orderable MPN, package information, functional requirements, application guidance, comparison parameters, and engineering considerations into a practical procurement and design reference. It also distinguishes the verified drop-in replacement from package or channel-count mismatches, helping engineers avoid substitutions that appear similar but would require PCB changes or redesign.

Permintaan RFG Kontak
MAX312CAE - Quad SPST 10Ω CMOS Switch | Analog Devices
MAX312CAE

MAX312CAE - Quad SPST 10Ω CMOS Switch | Analog Devices

The Analog Devices MAX312CAE is a quad, single-pole single-throw CMOS analog switch with a maximum on-resistance of 10Ω, 1.5Ω maximum on-resistance matching between channels, and operation in either signal direction. The device is associated with the MAX312, MAX313, and MAX314 family and is offered in a 12-pin package. It is designed for routing analog signals where low leakage, repeatable channel resistance, and compact multiplexing are important. A CMOS analog switch is a semiconductor device that uses controlled transistors to connect or disconnect an analog signal path. Within the broader hierarchy, an analog switch is an interface IC used for signal routing, multiplexing, demultiplexing, and test-signal selection. Unlike mechanical relays, it provides electronic switching without moving contacts and can be controlled by digital logic while preserving the selected signal's voltage range. The MAX312 family's principal electrical features include an on-resistance of 10Ω maximum, channel-to-channel on-resistance matching of 1.5Ω maximum, and low leakage of 2.5nA at +85°C. The product page also identifies rail-to-rail signal handling, single-supply operation from +4.5V to +30V, and dual-supply operation from ±4.5V to ±20V. These ratings make the family suitable for systems that route signals across a broad common-mode range. The MAX312/MAX313/MAX314 family is documented with a maximum ESD protection rating greater than 2000V per Method 3015.7 and crosstalk above 96dB at 20kHz. The Analog Devices product page identifies pin compatibility with the DG411, DG412, and DG413 families. On-resistance matching is particularly useful when multiple channels must present similar impedance to a precision measurement or signal-conditioning circuit. Typical uses include multiplexed sensor acquisition, instrumentation signal routing, test-equipment channel selection, data-acquisition systems, and general analog signal isolation. The switch can be used with a single supply or split supply, allowing integration into circuits that operate from a positive-only rail as well as systems requiring bipolar signal paths. Its 10Ω maximum resistance should be included in the design budget when driving high-impedance versus low-impedance downstream networks. For layout, route high-impedance signals directly to the relevant switch terminals and keep sensitive traces away from switching nodes and fast external clocks. Check the complete on-resistance curve for the selected signal voltage, because the published 10Ω value is a maximum rather than a constant resistance at every voltage and temperature. This page combines the manufacturer’s electrical and capability specifications, practical signal-routing considerations, and verified same-family replacement guidance. It also distinguishes documented functions from parameters that must be confirmed in the manufacturer datasheet before production release.

Permintaan RFG Kontak
MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices
MAX312EUE+

MAX312EUE+ - Quad 10Ω SPST Analog Switch | Analog Devices

Analog Devices MAX312EUE+ is a four-circuit CMOS analog switch with a 1:1 SPST topology, 10Ω maximum on-resistance, and a 16-pin TSSOP package. The device provides four independently controlled switches that conduct equally well in either signal direction, making it suitable for routing analog, digital, and low-voltage instrumentation signals. An analog switch is an integrated semiconductor device that connects or disconnects a signal path under digital control. The MAX312EUE+ belongs to the analog switch and multiplexer hierarchy within interface ICs, providing a defined on-state resistance, off-state leakage, and logic-controlled switching behavior. Its four-channel structure consolidates multiple point-to-point routing functions into one package. Key features include a maximum on-resistance of 10Ω and on-resistance matching of 1.5Ω between channels. Matching is important when several switched paths influence one measurement or signal chain because it helps minimize channel-dependent gain errors. The MAX312 also offers low leakage of 2.5nA at +85°C and equal conduction in both directions, allowing flexible signal-routing topology. The four SPST switches use CMOS control inputs, enabling each channel to be placed in a defined connection state independently. Four independent switches can support signal isolation, test-point selection, instrumentation routing, or the connection of external circuit sections to a shared analog node. The 16-pin TSSOP package supports surface-mount PCB assembly while keeping the circuit compact. Typical uses include data-acquisition systems, sensor signal conditioning, automated test equipment, sample-and-hold interfaces, battery-powered instrumentation, and general-purpose analog signal routing. Because the switches support bidirectional conduction, the same device can route either a source signal toward a load or connect a measurement chain back toward its source. PCB design should place the device near the signals it switches and route high-impedance sensor nodes to minimize parasitic capacitance and leakage. Control traces should remain away from sensitive analog inputs, and unused control inputs should be held at defined logic levels. Verify signal amplitude, bandwidth, temperature, and switch current against the manufacturer datasheet before finalizing the routing design. This product page combines the manufacturer’s switch specifications with practical PCB guidance, package details, selection criteria, and same-family drop-in alternatives. The comparison and design notes explain how on-resistance matching, leakage, logic control, and package reuse affect engineering decisions when replacing an existing four-channel analog switch.

Permintaan RFG Kontak