Produk (46.000+)

MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI
MAX313CUE+

MAX313CUE+ - Quad SPST CMOS Analog Switch | ADI

Analog Devices MAX313CUE+ is a quad SPST CMOS analog switch with four independently controlled normally open channels, a maximum on-resistance of 10 ohms, and a 16-pin TSSOP package. It supports single-supply operation from 4.5 V to 30 V and dual-supply operation from -4.5 V to -20 V and +4.5 V to +20 V. Typical on-resistance is 6.5 ohms, while guaranteed channel matching is 1.5 ohms maximum. A CMOS analog switch is a voltage-controlled semiconductor device that routes analog or digital signals between circuit nodes. The MAX313 belongs to the analog switch and multiplexer hierarchy, where an analog switch performs point-to-point routing and a multiplexer connects multiple signals to a common channel. Its SPST configuration provides one normally open path per switch, making it suitable for isolation, signal selection, test-fixture routing, and bidirectional analog-signal control. The four channels can conduct equally well in either direction. The MAX313CUE+ combines low on-resistance with channel-to-channel matching of 1.5 ohms maximum and on-resistance flatness of 2 ohms maximum over the specified signal range. These characteristics help minimize gain error and distortion when several switched channels must present similar resistance to downstream circuitry. It also provides low leakage and low power consumption for precision and power-sensitive systems. The MAX313 family operates from a wide supply range and supports rail-to-rail signal handling. According to the Analog Devices MAX313 product page, the devices are pin compatible with the DG411, DG412, and DG413 families. The manufacturer also specifies guaranteed ESD protection greater than 2000 V per Method 3015.7 and crosstalk above 96 dB at 20 kHz, helping protect sensitive analog paths and limit interaction between adjacent channels. Typical uses include precision test and measurement systems, analog signal-conditioning modules, battery-powered instrumentation, industrial control interfaces, and signal-isolation networks. The device can route sensor outputs, test signals, or external inputs without introducing the continuous power loss associated with a permanently conducting analog path. It is particularly useful when signal integrity, repeatable channel resistance, and low off-state leakage are more important than maximum switching speed. When laying out a MAX313CUE+ board, follow the TSSOP-16 pin-assignment table in the manufacturer datasheet and keep high-impedance routes short to minimize leakage pickup. Place supply decoupling close to the device, and evaluate switching transients when the source impedance is high. The normally open architecture requires the correct drive polarity at each control input; consult the control-input truth table before changing logic levels. This product record combines the manufacturer specifications, package information, replacement references, and practical design guidance into one engineering-focused view. It also identifies same-package alternatives and explains when their electrical or environmental differences matter, helping designers select the correct switch without introducing a footprint change.

Permintaan RFG Kontak
MAX314CPE+ - Quad SPST Analog Switch | Analog Devices
MAX314CPE+

MAX314CPE+ - Quad SPST Analog Switch | Analog Devices

The Analog Devices MAX314CPE+ is a four-circuit CMOS analog switch with four independently controlled SPST channels, a maximum on-resistance of 10 ohms, and a 16-pin PDIP package. Each switch conducts equally well in either direction, making the device suitable for routing analog, digital, and low-frequency instrumentation signals. An analog switch is a solid-state semiconductor device that connects or isolates circuit paths under electrical control. Unlike a mechanical relay, it operates without moving contacts, enabling fast switching and compact integration. The MAX314CPE+ belongs to the CMOS analog-switch hierarchy and provides four SPST channels in a through-hole package for applications that require signal routing rather than continuous power conversion. The device has a maximum on-resistance of 10 ohms and on-resistance matching between channels of 1.5 ohms. Its low leakage of 2.5 nA at +85°C helps preserve signal integrity in high-impedance circuits. Bidirectional conduction expands routing flexibility, while low power consumption supports both portable and fixed equipment. ESD tolerance greater than 2000 V per Method 3015.7 adds handling protection during assembly. Each of the four switch channels provides a separate control path, allowing a system to isolate a sensor, select a measurement route, or disconnect an external interface. The parallel CMOS structure avoids mechanical contact delay or wear, while the specified resistance matching helps limit channel-dependent gain and attenuation errors when multiple inputs are routed through the device. Typical uses include analog signal multiplexing in test and measurement equipment, channel isolation in data-acquisition systems, switching between sensors and amplifiers, and routing control signals in industrial control boards. The 16-pin PDIP package is particularly useful for prototypes, through-hole assemblies, and designs where a socketed or manually solderable package simplifies maintenance. When laying out the circuit, place each switched node close to its source and destination where practical, and avoid sharing long copper paths between sensitive channels. Confirm signal amplitude, leakage requirements, control logic levels, and switching transients against the manufacturer data sheet. The MAX314CPE+ is especially appropriate when four separately controlled, bidirectional, normally open analog paths are needed in a conventional through-hole design. This product page combines the manufacturer specifications, sourcing details, pin-package information, and practical selection guidance. It also identifies same-family alternatives while distinguishing verified drop-in choices from options that require a footprint or interface review before substitution.

Permintaan RFG Kontak
MAX314CUE+ - Quad 10Ω SPST CMOS Switch | Analog Devices
MAX314CUE+

MAX314CUE+ - Quad 10Ω SPST CMOS Switch | Analog Devices

The Analog Devices MAX314CUE+ is a quad, normally open SPST CMOS analog switch with a maximum on-resistance of 10Ω, 1.5Ω on-resistance matching between channels, and bidirectional signal conduction. The device operates from 4.5V to 30V and is packaged in a 16-pin TSSOP. Its four independent switches support low-power consumption, low leakage, and bidirectional analog routing. A CMOS analog switch is a semiconductor-controlled routing device that connects or isolates circuit nodes under digital control. The MAX314 family belongs to the analog-switch hierarchy, which includes multiplexers, selectors, and SPST switch arrays. Unlike a mechanical relay, an analog switch changes state electronically with no moving parts, making it suitable for compact instrumentation, signal-routing, and test systems. The MAX314 provides four single-pole, single-throw channels, a maximum on-resistance of 10Ω, and channel-to-channel matching of 1.5Ω. Because the switches conduct equally well in either direction, one package can route positive, negative, or bipolar signals. Leakage is specified at 2.5nA at +85°C, helping preserve signal integrity when a switch is off and high-impedance loads are connected. The four channels operate independently, allowing simultaneous control of separate signal paths. Matching of 1.5Ω minimizes gain or attenuation differences caused by unequal switch resistance, while the 10Ω maximum on-resistance supports common low-level analog signals. The CMOS implementation also provides low power consumption, although supply current and switching timing should be checked against the operating conditions in the manufacturer datasheet. Typical uses include signal isolation between instrumentation channels, routing between a sensor and a measurement circuit, and selecting inputs in test and measurement equipment. The device can also serve in industrial control systems where an external controller must connect a source to an analog processing chain without changing the baseband voltage. For PCB design, keep control traces away from sensitive analog routes and provide a stable ground reference to all package pins. Confirm the absolute maximum voltage, input logic levels, charge injection, off leakage, and switching-time limits before applying the device to high-voltage or high-speed signals. This page combines the MAX314 family electrical characteristics, pin-compatible alternatives, application guidance, comparison parameters, and practical PCB considerations in a format designed for rapid component selection and design review.

Permintaan RFG Kontak
MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices
MAX3160EAP+

MAX3160EAP+ - 3.0-5.5V Multiprotocol Transceiver | Analog Devices

The Analog Devices MAX3160EAP+ is a 3.0V to 5.5V RS-232/RS-485/RS-422 multiprotocol transceiver with a 20-pin SSOP package. It is programmable as a two-transmitter, two-receiver RS-232 interface or as a single RS-485/RS-422 transceiver, allowing one physical interface circuit to support multiple serial protocols. The device also supports pin-selectable transmitter slew rates for RS-232 and RS-485/422 operation, helping reduce EMI and cable reflections. Analog Devices identifies the MAX3160 family as a low-power multiprotocol interface solution, with a listed 1 uA operating-current feature and data rates up to 250 kbps for suitable operation. The MAX3160EAP+ is packaged as a 20-SSOP surface-mount device. Its protocol configurability makes it useful in industrial controls, interface converters, networking peripherals, point-of-sale equipment, and security systems where a board must accommodate legacy RS-232 alongside balanced RS-485 or RS-422 links. The MAX3160 family is pin-programmable, so the same PCB can be configured differently during assembly or test. Compared with a fixed RS-232 transceiver, the MAX3160EAP+ adds RS-485/RS-422 capability and selectable slew-rate control in one interface IC. Its low operating-current positioning is important for portable and space-constrained equipment, while the SSOP footprint simplifies integration with conventional surface-mount assembly. Design decisions should confirm the selected protocol, termination requirements, cable length, data rate, and logic-level compatibility against the manufacturer datasheet.

Permintaan RFG Kontak
MAX317ESA+ - 35Ω Precision SPST CMOS Switch | Analog Devices
MAX317ESA+

MAX317ESA+ - 35Ω Precision SPST CMOS Switch | Analog Devices

Analog Devices MAX317ESA+ is a precision, normally closed, single-pole single-throw CMOS analog switch with 35Ω on resistance, one channel, 8-SOIC packaging, and operation across 10V to 30V supplies. The device accepts dual supplies ranging from ±4.5V to ±20V, making it suitable for bipolar analog-signal routing where a conventional single-supply switch cannot accommodate the full signal range. An analog switch is an electronically controlled semiconductor device that connects or isolates circuit nodes. The MAX317 belongs to the CMOS analog-switch hierarchy, where low on resistance and low leakage preserve signal integrity through a switched path. Its normally closed architecture keeps the two external signal terminals connected when the control input is inactive and disconnects them when the control input is asserted. The MAX317 family combines on resistance below 35Ω with resistance matching within 2Ω between channels. The on-resistance profile remains flat across the analog signal range, with a maximum change of 3Ω in the manufacturer’s characterization. Leakage is less than 250pA at +25°C and less than 6nA at +85°C, helping preserve high-impedance measurements and reduce loading on adjacent circuits. The MAX317 uses a monolithic CMOS implementation optimized for precision signal switching rather than power switching. Its low-leakage behavior is particularly useful when the switched node has a high source impedance, where even a small parasitic current can create a meaningful voltage error. The normally closed function should also be considered carefully because the default signal path differs from a normally open analog switch. Typical uses include precision test and measurement equipment, data-acquisition front ends, analog signal isolation, sample-and-hold systems, and bipolar instrument switching. In these applications, the switch can route instrumentation signals while keeping the selected channel in a defined connection state. The MAX318 and MAX319 family members provide normally open and SPDT alternatives for designs requiring different default behavior. When laying out the circuit, keep analog traces short and connect the device ground pins to the signal-return reference. Avoid placing the switch where its on resistance would create excessive attenuation in a high-impedance measurement path. Verify the supply polarity, control-logic levels, and maximum signal voltage before applying power, particularly in dual-supply systems. This product overview combines the manufacturer’s switch characteristics with practical routing guidance, package information, lifecycle context, and a conservative drop-in replacement assessment for engineers evaluating the MAX317ESA+ footprint.

Permintaan RFG Kontak
MAX31856MUD+ Precision Thermocouple Converter | Analog Devices
MAX31856MUD+

MAX31856MUD+ Precision Thermocouple Converter | Analog Devices

The Analog Devices MAX31856MUD+ is a precision thermocouple-to-digital converter with cold-junction compensation, digital linearization, Celsius-formatted output, and a 14-TSSOP package. The verified source data identifies 0.0078125°C resolution and supports readings from -55°C to 125°C for the listed device context, with thermocouple measurements reaching as high as +1800°C. It converts thermocouple signals into digital temperature data while supporting multiple thermocouple types through device configuration. A thermocouple-to-digital converter is an interface IC that conditions a low-voltage thermoelectric voltage, performs cold-junction compensation, applies the appropriate linearization for the selected thermocouple type, and transfers temperature data to a host controller. The MAX31856 belongs to the sensor and detector interface category and sits between physical temperature sensors and digital embedded systems. Its digital interface makes temperature monitoring suitable for industrial equipment, test systems, control loops, and embedded instrumentation. The verified manufacturer result identifies cold-junction compensation, thermocouple signal digitisation, linearization, Celsius output format, and 0.0078125°C resolution as central features. The device is supplied in a 14-pin TSSOP package, with the MUD+ ordering code shown by DigiKey as a thermocouple-to-digital converter IC. The source material does not provide a complete verified set of electrical limits, SPI timing values, thermocouple input ranges for every type, or package dimensions, so those values are not inferred here. Because a thermocouple measures the temperature difference between a sensing junction and a reference junction, cold-junction compensation is essential for accurate measurements near ambient temperature. The MAX31856 handles this function internally, allowing the host system to receive compensated digital temperature data rather than raw thermocouple voltage. Digital linearization further reduces the software burden associated with converting nonlinear thermocouple voltage into temperature. Typical uses include industrial furnace monitoring, temperature-controlled processes, laboratory equipment, environmental monitoring, and embedded thermal control. In each case, the thermocouple type, wiring, cold-junction implementation, grounding strategy, and digital interface configuration must be selected according to the manufacturer's datasheet. The verified data does not identify a specific companion MCU or application reference design, so companion products are not asserted as manufacturer-recommended parts. The principal design consideration is ensuring that the selected thermocouple, input filtering, grounding, and digital interface match the system measurement range. For thermocouple signals, keeping the analog input path away from switching nodes and noisy digital return currents helps preserve measurement integrity. This page consolidates verified distributor listings, the official Analog Devices product page, and the available cross-reference information without inventing missing electrical parameters.

Permintaan RFG Kontak
MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices
MAX318CPA+

MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices

The Analog Devices MAX318CPA+ is a precision, normally open, single-pole single-throw CMOS analog switch with an on-resistance of 35 ohms, housed in an 8-pin PDIP package. It routes one analog signal using a 1:1 SPST topology and is designed for precision signal-selection and test systems. An analog switch is a semiconductor interface device that connects or disconnects an analog signal path under digital control. The MAX318CPA+ belongs to the analog switch hierarchy within interface ICs and multiplexers, providing a simpler alternative to a multi-channel multiplexer when only one signal path must be selected. Its normally open configuration keeps the switched node disconnected until the control input activates the path. Key characteristics include a maximum on-resistance of 35 ohms, operation from 4.5 V to 20 V, and normally open SPST behavior. The device is specified as a precision CMOS analog switch with low on-resistance that remains substantially flat across the analog signal range. According to the Analog Devices MAX318 product page, on-resistance is guaranteed below 35 ohms and is matched within 2 ohms between channels in the associated precision-switch family. The MAX318CPA+ is intended for precision instrumentation, signal routing, test and measurement equipment, industrial control interfaces, and data acquisition systems. Its single-channel architecture simplifies control logic while preserving the low resistance required to transfer low-level or precision analog signals. The 8-pin PDIP package also supports conventional through-hole assembly and prototype boards where fine-pitch surface-mount routing would be inconvenient. Designers should verify the control logic, supply voltage, allowable signal voltage, and switching transients against the manufacturer data sheet before use. Because an analog switch can introduce small resistance variation, channel resistance matching, charge injection, off leakage, and bandwidth determine whether it is suitable for a particular signal path. Input and output protection may also be required when external voltages exceed the device ratings. This page combines the manufacturer specifications, verified sourcing links, application guidance, comparison information, and practical design notes to support component selection and PCB implementation. The MAX318CPA+ is best suited to designers who need a simple, normally open, precision SPST switch rather than a multi-channel multiplexer.

Permintaan RFG Kontak
MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim
MAX318CSA+

MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim

The Maxim Integrated MAX318CSA+ is a precision, single-pole single-throw (SPST) normally-open CMOS analog switch with a maximum on-resistance of 35 Ohm, packaged in an 8-pin SOIC (NSOIC) surface-mount package. It is a 1:1 multiplexer: one independent switch, one signal path, complementary-family sibling to the MAX317 (normally closed) and MAX319 (SPDT) parts in the same series. An analog switch is a solid-state, MOSFET-based signal router that connects or disconnects an analog signal path under digital control, sitting in the interface IC layer between sensors, converters and a system microcontroller. Unlike a mechanical relay, it switches in nanoseconds with negligible off-state leakage, making it the standard building block for sample-and-hold front ends, programmable gain stages, test-point muxes and isolated-signal routing. Key characteristics of the MAX318CSA+ include a maximum on-resistance of 35 Ohm, on-resistance matching held within 2 Ohm between channels and variation of only 3 Ohm maximum across the analog signal range, and very low leakage of less than 250 pA at +25 degC rising to less than 6 nA at +85 degC. The part is listed in production by Analog Devices and is specified over a 0 degC to +70 degC commercial temperature range in the SOIC package. Internally the device uses CMOS transmission gates, so the signal path is symmetrical and the switch behaviour does not depend on the control polarity in the same way a bipolar multiplexer does. The small, flat on-resistance curve preserves signal integrity for low-frequency analog signals, while the low leakage keeps the off-state contribution to system error negligible when a single measurement or sensor node is selected. Typical uses include routing sensor outputs into a single ADC input, multiplexing discrete resistive networks into a programmable gain amplifier, isolating a precision reference from a measurement node, selecting between test points during board bring-up, and building small sample-and-hold front ends in instrumentation equipment. Any of these functions can also be handled with a relay, but the CMOS switch removes the slow mechanical switching time and the contact bounce that plague relay-based solutions at higher cycle rates. When laying out the MAX318CSA+, place the device close to the source and destination of the analog path so that the switched trace stays short and the 35 Ohm series resistance has the least effect on signal settling. Keep the supply decoupling capacitor adjacent to the V+ and ground pins, and route control traces away from the analog node where board area allows, because charge injection through the control line can create a transient step at the moment of switching. This page consolidates the distributor availability picture, the family-level drop-in alternatives in the same 8-SOIC footprint, and the practical routing and layout notes that engineers usually have to piece together from the manufacturer data sheet and application experience.

Permintaan RFG Kontak
MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices
MAX319CSA+

MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices

The Analog Devices MAX319CSA+ is a precision, single-pole double-throw CMOS analog switch with one normally open and one normally closed path, a maximum on-resistance of 35Ω, and an 8-pin SOIC package. It is designed for precision signal routing where low on-resistance, low charge injection, low power consumption, and high electrostatic-discharge withstand are important. An analog switch is a semiconductor interface that routes an analog signal between circuit nodes under digital control. Unlike a relay, it operates electronically at low voltage and can switch signals rapidly without mechanical wear. The MAX319 belongs to the broader analog-switch hierarchy, which sits alongside multiplexers, demultiplexers, and interface ICs used to connect sensors, test equipment, measurement systems, and signal-processing electronics. Key electrical characteristics include on-resistance below 20Ω typical and 35Ω maximum, guaranteed channel matching within 2Ω, and on-resistance variation of no more than 3Ω maximum across the analog signal range. Charge injection is low at 10pC, while power consumption is 35µW. These characteristics help preserve signal fidelity when the switch is used in measurement, control, or data-acquisition paths. The MAX319 family uses an improved silicon-gate CMOS process and rail-to-rail analog signal handling capability associated with a 44V maximum breakdown voltage. Its precision configuration is useful when signal-source impedance, leakage, or switch resistance could otherwise influence the measurement result. The MAX319CSA+ ordering code identifies the 8-pin SOIC package and the manufacturer's standard production configuration. Typical uses include battery-powered instrumentation, automated test equipment, analog measurement systems, signal-path routing, sample-and-hold circuits, and industrial control interfaces. Its low 35µW power consumption is particularly useful in portable equipment, while the 35Ω maximum on-resistance is suitable for moderate-impedance analog signals rather than ultra-low-impedance precision dividers. When designing a circuit around the MAX319CSA+, account for the switch's on-resistance, leakage, charge injection, and off-state behavior when calculating signal attenuation and timing. Place the device close to sensitive signal paths, maintain adequate grounding, and use the manufacturer pin-description table when assigning PCB tracks. Verify the logic levels and control polarity against the actual device documentation before finalizing the layout. This product page combines the manufacturer's device specifications with practical design guidance, package information, sourcing details, and a conservative drop-in assessment. It emphasizes verified distinctions between electrically similar devices so engineers can determine whether a replacement preserves both the board footprint and the required switch behavior.

Permintaan RFG Kontak
MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices
MAX3221CAE+

MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CAE+ is a one-driver, one-receiver RS-232 transceiver designed for +3V to +5.5V operation and supplied in a 16-pin SSOP package. It provides 1 µA supply current when AutoShutdown is active, while integrating the charge-pump circuitry required to generate RS-232-compatible driver levels from a low-voltage supply. The MAX3221CAE+ is suitable for portable equipment, industrial controls, data acquisition systems, and other equipment that requires a compact, low-power serial interface. An RS-232 transceiver is an interface IC that combines a transmitter and receiver for communicating between a logic-level device and an RS-232 port. The transmitter converts low-voltage TTL or CMOS signals into RS-232 levels, while the receiver converts incoming RS-232 signals back into logic-compatible levels. The MAX3221 family belongs to the interface IC hierarchy and provides a practical way to bridge modern embedded systems with legacy RS-232 equipment. The MAX3221CAE+ includes Maxim's AutoShutdown feature, allowing the on-board power supply and driver circuitry to shut down when the receiver does not detect a valid signal. According to the Analog Devices MAX3221 product page, the device operates from +3V to +5.5V and reaches a supply current of 1 µA. These characteristics are particularly valuable in battery-powered instruments where a permanently active RS-232 interface would increase standby power consumption. The MAX3221 is a 1-driver/1-receiver 16-pin SSOP version of the 2-driver/2-receiver MAX3223. Its integrated RS-232 supply uses charge-pump circuitry to develop the voltage swing needed by the transmitter. The C designation denotes the family's capacitor configuration, while the E designation provides shutdown-control functionality. The A suffix identifies the package and temperature-related ordering configuration used in the MAX3221CAE+ ordering code. Typical applications include battery-powered test equipment, handheld configuration tools, serial adapters, industrial instrumentation, point-of-sale equipment, and embedded systems that must communicate with a host computer through an RS-232 port. The 16-pin SSOP footprint is useful for compact designs, although engineers should verify connector protection, cable length, logic levels, and supply compatibility against the system requirements. The principal design consideration is signal integrity. RS-232 is a single-ended, unbalanced interface, so cable routing and ground quality can materially affect noise immunity. Place the transceiver close to the interface connector, provide a low-impedance ground path, use suitable protection for exposed cables, and observe the manufacturer's recommended charge-pump capacitor values. External circuitry may also be required for hardware handshaking or for conditioning signals on long or electrically noisy cables. This page organizes the MAX3221CAE+ specifications, application guidance, package information, and verified same-package alternatives into an engineering-focused reference. It also highlights the practical trade-offs among shutdown, supply-voltage, capacitance, and temperature variants so designers can make a replacement decision based on actual circuit requirements rather than package similarity alone.

Permintaan RFG Kontak
MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+T

MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+T is a one-driver, one-receiver RS-232 transceiver with AutoShutdown, operating from a 3 V to 5.5 V supply and drawing 1 µA when the charge-pump circuit is inactive. The device is packaged in a 16-pin SSOP and is designed for compact, low-power serial-interface equipment. Its principal characteristics are one RS-232 driver, one RS-232 receiver, 3 V to 5.5 V operation, and automatic supply shutdown when no valid receiver signal is detected. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class of interface ICs, which sits between computer serial ports or control equipment and external communication links. The MAX3221 is the one-driver, one-receiver member of the MAX3221 family and is smaller than two-channel RS-232 transceivers such as the MAX3223. AutoShutdown is the device's principal power-management feature. When the receiver does not detect a valid signal level, the onboard power supply and driver shut down, reducing supply current to 1 µA as stated on the manufacturer product page. This behavior is valuable in battery-powered or intermittently connected equipment because a permanently connected serial port no longer needs to retain a full charge-pump load when communication is inactive. The 3 V to 5.5 V supply range supports integration with both 3.3 V and 5 V system rails. The MAX3221 integrates the RS-232 line driver, receiver, and onboard charge-pump circuitry in one compact package. This integration eliminates a separate external power-supply circuit while providing the voltage conversion required by the RS-232 interface. Unlike designs requiring a ±12 V supply, the MAX3221 generates RS-232-compatible levels from a single low-voltage supply. Its 16-SSOP construction supports conventional surface-mount assembly while conserving board area in embedded control, industrial, and communications systems. Typical applications include single-port serial-control links in industrial equipment, point-of-sale terminals, data-acquisition systems, instrumentation, and battery-operated peripherals. In each case, the device handles one unidirectional data path with the driver and the opposite direction with the receiver. Because it provides only one driver and one receiver, a design needing two physical RS-232 channels should evaluate a two-channel transceiver rather than adding a second MAX3221 unnecessarily. The primary design consideration is external bypass capacitance. Place the supply bypass capacitor and charge-pump capacitor close to their associated pins, with short ground paths to reduce supply disturbance and improve interface stability. Confirm the external capacitor values and connection details in the manufacturer datasheet before layout release, especially in designs operating from 3.3 V where charge-pump headroom and startup behavior affect system margins. This page combines the manufacturer product information with practical interface guidance, structured specifications, verified pin-compatible family alternatives, and design considerations that help engineers evaluate the MAX3221CAE+T for low-power RS-232 implementations.

Permintaan RFG Kontak
MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+TG1Z

MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+TG1Z is a single-driver, single-receiver RS-232 line transceiver designed for true +3V to +5.5V operation. It provides one driver and one receiver in a 16-pin SSOP package, supports the full RS-232 interface standard, and draws only 1 µA through the AutoShutdown feature when no valid receiver signal is detected. The commercial-temperature, tape-and-reel ordering designation is MAX3221CAE+TG1Z. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic. The MAX3221 belongs to the hierarchy of RS-232 interface transceiver, serial interface IC, interface controller, and semiconductor. It is intended for equipment that needs bidirectional or unidirectional point-to-point serial connectivity without relying on a modern multi-standard transceiver family. The principal features of the MAX3221 include one RS-232 driver, one RS-232 receiver, operation from 3V to 5.5V, and a 1 µA AutoShutdown supply current. AutoShutdown reduces supply demand when the receiver does not detect a valid signal level. This makes the device useful in portable equipment and systems where a permanently connected serial port would otherwise waste power. Its 16-terminal gull-wing SSOP construction supports compact surface-mount assemblies. The device uses Maxim's low-power RS-232 interface architecture to support systems that cannot tolerate excessive supply current. The on-board charge-pump and driver circuitry provide the voltage swings required by RS-232 while the receiver converts the line-level input into a digital output. Designers should still account for the voltage difference between logic-side ground and the RS-232 line reference when integrating the device with another circuit board. Typical uses include industrial serial adapters, test equipment, data acquisition modules, point-of-sale terminals, instrument-control links, and legacy peripheral interfaces. The MAX3221 is especially appropriate where a compact single-channel interface is required rather than the multiple drivers and receivers offered by larger RS-232 families. For battery-powered instruments, its 1 µA shutdown current can reduce standby consumption. A key design consideration is ensuring that the logic supply, charge-pump capacitors, driver connection, receiver input, and signal ground are routed according to the manufacturer application guidance. Keep the interface connector and transceiver return path together where practical, and use suitable protection for exposed cables. Review the manufacturer's pin description and application circuit before assigning the 16 SSOP terminals or selecting external bypass capacitors. This product record combines the official MAX3221 family information, exact package attributes, commercial sourcing information, pin-compatible alternatives, comparison parameters, and application guidance to support component selection and board-level implementation.

Permintaan RFG Kontak
MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDB

MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDB is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDB alongside other single-channel RS-232 transceivers.

Permintaan RFG Kontak
MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3221CDBR

MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX3221CDBR is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDBR alongside other single-channel RS-232 transceivers.

Permintaan RFG Kontak
MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDBRG4

MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDBRG4 is a single-channel RS-232 line driver and receiver with a 3 V to 5.5 V supply, 250 kbit/s operation, and ±15 kV ESD protection, housed in a 16-pin SSOP package. The transceiver integrates one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit for generating the bipolar voltage levels required by RS-232. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a RS-232 link. Within the signal-chain hierarchy, it belongs to the RS-232 interface, line-driver and receiver, communications-interface, and semiconductor categories. The MAX3221CDBRG4 is intended for equipment that needs one bidirectional serial port while operating from a 3 V to 5.5 V system supply. Key features include a maximum data rate of 250 kbit/s, ±15 kV ESD protection on the serial-port connection pins, and a low shutdown supply current. According to the manufacturer datasheet, the device provides AutoShutdown operation and supports true +3 V to +5.5 V supplies. Its integrated charge pumps reduce the external component count compared with a discrete RS-232 interface implementation. The MAX3221 family combines a driver and receiver with internal level-shifting circuitry. The charge-pump section develops positive and negative voltage rails from the single device supply, allowing the line interface to produce RS-232-compatible output levels. The receiver converts the bipolar serial signal back to a logic-compatible signal, while the dedicated receiver-enable control can place the receiving path in a reduced-power state when it is not required. Typical uses include industrial serial-port adapters, point-to-sale equipment, test and measurement instruments, embedded control systems, and legacy peripheral connections. The single-channel arrangement is especially suitable for compact systems that need one RS-232 port but no multi-port RS-232 expansion. When designing around the MAX3221CDBRG4, preserve the charge-pump capacitor and bypass-capacitor placement recommended in the manufacturer datasheet. Confirm that the host interface uses the correct logic voltage and that the receiver-enable polarity matches the controller firmware. The 16-pin SSOP footprint also requires careful solder-joint inspection because lead pitch and package density can complicate rework. This product page consolidates the electrical limits, interface function, packaging information, and practical design considerations for the MAX3221CDBRG4. It also identifies verified drop-in alternatives and organizes the selection trade-offs by speed, supply range, temperature grade, and interface configuration.

Permintaan RFG Kontak
MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI
MAX3221CPW

MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI

Texas Instruments MAX3221CPW is a single-channel RS-232 line driver/receiver with a 3 V to 5.5 V supply, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. The device is packaged in a 16-pin TSSOP package and includes one line driver, one line receiver with a dedicated enable pin, and a dual charge-pump circuit. It is designed to provide the electrical interface between an asynchronous communication controller and a serial-port connector while operating from a single supply voltage. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts received RS-232 signals back into logic-level signals. The MAX3221 belongs to the RS-232 interface IC hierarchy, which includes line drivers, line receivers, and charge-pump-assisted transceivers used for serial communications equipment, industrial controls, instrumentation, and point-of-sale terminals. The dual charge-pump circuit generates the positive and negative voltage levels required by the RS-232 interface without requiring a separate negative supply. The MAX3221 operates from 3 V to 5.5 V, accepts 5 V logic input with a 3.3 V supply, and supports data rates to 250 kbit/s. Its low standby current of 1 µA typical and use of external 0.1 µF capacitors help support compact, power-conscious interface designs. The dedicated receiver enable pin allows the receiver to be disabled when the host does not need to monitor the serial link. The device meets TIA/EIA-232-F requirements and is also associated with ITU V.28 operation, providing a standard RS-232 electrical interface for asynchronous communication systems. The ±15 kV ESD protection is specified pin to pin, including the serial-port connection pins and ground. This protection helps improve system robustness when cables are exposed to electrostatic discharge during installation, servicing, or normal handling. Typical uses include single-channel serial console links, industrial serial adapters, programmable instrument interfaces, barcode and point-of-sale equipment, and embedded systems that require one bidirectional RS-232 channel. The 250 kbit/s capability is appropriate for legacy serial peripherals and control links, while the 3 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. When laying out the circuit, place the charge-pump capacitors and the driver and receiver interface capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog or high-speed digital signals. Confirm that the transceiver enable state matches the host controller’s serial-port requirements before relying on low-power standby operation. This page combines the manufacturer’s RS-232 interface specifications with package and application guidance, verified comparison candidates, and practical design notes for engineers evaluating the MAX3221CPW in compact serial-interface designs.

Permintaan RFG Kontak
MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments
MAX3221CPWE4

MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWE4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply. The device provides one transmit channel, one receive channel, integrated charge-pump circuitry, and ±15 kV ESD protection in a 16-pin TSSOP package measuring 4.40 mm wide. Its interface operates at the voltage levels required by RS-232 while the low-voltage supply supports modern embedded systems. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level voltages. In the broader semiconductor hierarchy, the MAX3221CPWE4 belongs to the interface IC family and provides the physical signaling layer between a host controller and a serial peripheral. The integrated dual charge pump generates the positive and negative voltage levels required by the RS-232 standard without external discrete capacitors. The principal electrical characteristics visible in the manufacturer documentation include a 3 V to 5.5 V operating supply, single-channel driver and receiver operation, and ±15 kV ESD protection. The single-channel arrangement reduces board area and power consumption compared with multi-channel RS-232 transceivers. The 16-pin TSSOP package is also compatible with surface-mount manufacturing and supports compact serial-interface implementations. The MAX3221CPWE4 uses an RS-232 line driver to convert TTL-compatible transmit data into bipolar line signaling and an RS-232 receiver to recover logic-compatible receive data. A dedicated receiver-enable function provides control over the receive path. Internal dual charge-pump circuitry supports the positive and negative voltage swings associated with RS-232 signaling while operating from a single low-voltage supply. Typical applications include industrial serial-port equipment, data-acquisition systems, service-console interfaces, programmable instrumentation, and embedded control systems that need a compact RS-232 connection. It is particularly suitable when the logic system operates from 3.3 V or 5 V and an RS-232 port must be added without designing a separate high-voltage transmitter circuit. A critical implementation consideration is the distinction between the low-voltage supply and the bipolar voltages generated on the RS-232 side. Decoupling must be placed close to the supply pins, and external charge-pump capacitors must follow the values and layout guidance in the manufacturer datasheet. The PCB should also provide appropriate isolation and return-path planning for the externally accessible serial connector. This product page consolidates the exact-orderable part information, operating limits, package details, replacement guidance, and design-focused guidance that engineers need when evaluating the MAX3221CPWE4. It also provides a structured comparison with same-footprint MAX3221 variants so that temperature-grade, suffix, and sourcing decisions can be made without confusing electrical equivalence with PCB compatibility.

Permintaan RFG Kontak
MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CPWRE4

MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWRE4 is a single-channel RS-232 line driver and receiver with a dual charge-pump circuit, a 3 V to 5.5 V supply range, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. It is packaged in a 16-pin TSSOP and includes a receiver with a dedicated enable input. The device provides the electrical interface between TTL-compatible logic and an RS-232 port while requiring external charge-pump capacitors of 0.1 µF. An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into the positive and negative voltage swings used by RS-232 equipment. In the broader semiconductor hierarchy, the MAX3221 belongs to the interface IC family, where line drivers and line receivers bridge computer, industrial-control, instrumentation, and communications equipment. Its single-channel architecture is useful when a system needs one bidirectional RS-232 connection rather than the multiple channels found on multi-channel transceiver families. The MAX3221 operates from 3 V to 5.5 V and accepts 5 V logic input when operated from a 3.3 V supply. Its 250 kbit/s data rate supports legacy serial-port, point-to-point control, and embedded equipment links. Pin-to-pin ESD protection of ±15 kV applies to the RS-232 connection pins, including ground, helping protect the interface against electrostatic discharge encountered during installation or handling. Internally, the device combines one line driver, one line receiver with a dedicated enable input, and a dual charge-pump circuit. The charge pumps generate the positive and negative voltages required for compliant RS-232 signaling. The receiver enable function allows a system to place the receive side in a controlled state, while the low standby current supports power-conscious designs where the interface must remain present without continuously receiving data. Typical uses include single-port RS-232 equipment interfaces, industrial controller serial links, programmable-instrument connections, and embedded systems that communicate with legacy peripherals. Because the logic side operates from 3 V to 5.5 V, the device can be used in both 3.3 V and 5 V systems. The 16-pin TSSOP also supports compact board layouts where a larger multi-channel transceiver would be unnecessary. Designers should place the 0.1 µF charge-pump capacitors close to their designated pins and observe the connector-side voltage and polarity requirements of RS-232. The interface does not create isolation, so an exposed or long cable run may require additional surge and ground-management measures. Input and output logic levels must also be checked against the connected controller rather than assumed from the serial-port standard. This page organizes the technical specifications, source links, interface applications, drop-in alternatives, and PCB considerations for engineers evaluating the MAX3221CPWRE4. It also distinguishes exact electrical matches from variants that change package details or feature sets, helping prevent a nominal substitution from creating an unintended PCB or firmware incompatibility.

Permintaan RFG Kontak
MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices
MAX3221CUE+

MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+ is a production RS-232 transceiver for single-driver, single-receiver communications links. It operates from +3V to +5.5V and is specified for EIA/TIA-232 and V.28/V.24 interfaces. The device includes one line driver, one receiver with a dedicated enable input, and a dual charge-pump circuit that supplies the RS-232 bipolar signal levels required by the communications interface. The MAX3221 family also uses Maxim’s AutoShutdown feature, allowing the on-board supply and drivers to shut down when no valid receiver signal is present, reducing supply consumption in systems where the interface is intermittently active. The MAX3221CUE+ is packaged in a 16-pin TSSOP and is identified by the C suffix and E-grade temperature designation in the manufacturer’s product family documentation. An RS-232 transceiver is an interface IC that translates between single-ended logic-level signals and the voltage-defined, bipolar signaling used by RS-232 equipment. In the transmit direction, the line driver converts logic-level data into an RS-232 signal; in the receive direction, the receiver converts the incoming RS-232 signal into a logic-level output. The dual charge-pump circuit supports the voltage translation required by the RS-232 standard without requiring a separate negative supply. The receiver enable pin gives the system designer a way to control whether the receiver is active, while AutoShutdown provides an additional power-management mechanism for ports that may be idle. The key verified characteristics of the MAX3221CUE+ include its +3V to +5.5V supply range, 1 µA-class shutdown current as described by the manufacturer family documentation, RS-232 transceiver operation, and its 16-pin TSSOP package. The Newark distributor listing identifies the part as an RS-232 transceiver with 120 Kbps signaling and a 70°C operating-temperature listing. The Analog Devices product page identifies the MAX3221 family as production and lists a starting list price of $2.52. Additional operating, electrical, and environmental details are available in the manufacturer datasheet and should be confirmed against the specific ordering code before design release. Typical uses include legacy serial-port equipment, industrial control links, data-acquisition equipment, and embedded systems that require a compact RS-232 port. The MAX3221CUE+ can be used when a design needs a low-voltage digital supply while retaining conventional RS-232 signaling at the connector. Its single-driver and single-receiver organization is appropriate for point-to-point links rather than multi-drop RS-232 networks. The dedicated receiver enable and AutoShutdown functions are useful in systems where the interface must remain available without continuously powering the complete driver and receiver circuitry. The primary design consideration is verifying the exact pinout, capacitor values, and signal-termination requirements from the MAX3221 manufacturer datasheet. Charge-pump capacitors must be placed close to their associated pins, and the RS-232 connector-side circuit should be designed for the voltage and ESD requirements of the application. The MAX3221CUE+ is appropriate when the required interface is one driver and one receiver in a 16-pin TSSOP footprint; designers needing multiple drivers or receivers should select a larger RS-232 transceiver family instead. This page combines manufacturer family information, distributor pricing, verified cross-reference results, application guidance, and design cautions to support practical sourcing and comparison of the MAX3221CUE+ rather than reproducing only the basic distributor description.

Permintaan RFG Kontak
MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221CUE+T

MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+T is a one-driver, one-receiver RS-232 transceiver designed for operation from a 3.0 V to 5.5 V single supply. The device combines a dual charge-pump supply, automatic shutdown, and a low-dropout line driver in a 16-pin TSSOP package. Its RS-232 line-driver output and receiver input are intended for serial-port connections, while the integrated charge pumps generate the bipolar voltage required to transmit RS-232 signals from a low-voltage supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals into logic-level inputs. In the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class, interface IC category, and broader semiconductor family. It is appropriate where a modern controller operates from 3.0 V or 5.0 V but the attached equipment still uses the voltage range and signaling conventions of the RS-232 standard. The MAX3221 uses AutoShutdown to reduce supply consumption when no valid receiver signal is detected. According to the manufacturer, this feature can reduce onboard supply and driver current to approximately 1 µA when the receiver inputs are inactive. The MAX3221CUE+T ordering code identifies the temperature-range and package configuration, while the +T suffix denotes the tape-and-reel shipping format shown for this part. Internally, the proprietary dual charge-pump circuit produces the elevated voltage used by the driver from one 3.0 V to 5.5 V supply. This architecture avoids a separate negative power rail in equipment using a single positive supply. The receiver converts the RS-232 input into CMOS-compatible logic, and the driver presents the required RS-232 output levels to the connector-side interface. Typical uses include industrial control panels, point-of-sale terminals, serial adapters, embedded instrumentation, and service equipment that must connect a low-voltage processor to an RS-232 port. The 16-pin TSSOP package also suits compact boards where connector spacing and component height are important. The AutoShutdown behavior is particularly useful in battery-powered or intermittently connected portable systems. Layout should place charge-pump capacitors and interface-path components close to the device, keep the RS-232 traces away from sensitive analog and high-speed digital nets, and provide a low-impedance ground return. The external interface must also satisfy the applicable RS-232 voltage, grounding, and ESD requirements. Because this integrated circuit generates only a small number of RS-232 channels, a multiport design may require multiple transceivers or a higher-channel-count device. This product page combines the manufacturer specifications, package information, RS-232 application context, practical layout guidance, and a pin-compatible comparison focused on helping engineers determine whether the MAX3221CUE+T can be used without redesigning an existing 16-pin TSSOP circuit.

Permintaan RFG Kontak
MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices
MAX3221EAE+

MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices

The Analog Devices MAX3221EAE+ is a 3V-powered, 1-driver/1-receiver RS-232 transceiver with AutoShutdown, operating from 3V to 5.5V and reaching 120 kbps in a 16-pin SSOP package. It provides one transmit driver, one receive path, automatic shutdown and wake-up, and enhanced ESD protection according to the verified manufacturer description. The device is intended for low-voltage serial interfaces where power efficiency, compact footprint, and reliable RS-232 signal translation are required. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 links. The MAX3221 family uses an internal charge-pump circuit to generate the RS-232 transmitter voltage from a single low-voltage supply. In the system hierarchy, it is a communication interface IC, a line-interface device, and a voltage-level translator used between host controllers and external serial equipment. Key verified characteristics include a 3V to 5.5V supply range, 120 kbps data-rate capability, 1 microamp supply-current operation in shutdown, one RS-232 driver, and one receiver. AutoShutdown reduces power use when the receiver does not detect a valid signal. The 16-SSOP package is specified as approximately 5.30 mm wide in the distributor result, making the device suitable for compact equipment designs. The MAX3221EAE+ is appropriate for embedded serial-console connections, industrial control links, point-of-sale systems, instrumentation, and USB-to-RS-232 adapters. The internal charge pump removes the need for a separate bipolar supply, while the receiver and driver provide the basic signal path between a low-voltage controller and an RS-232 connector. The tradeoff is that RS-232 is a single-ended, point-to-point interface with limited cable distance and no multidrop capability. For layout, place charge-pump capacitors and the receiver/transmitter interface components close to their associated pins, and follow the manufacturer's recommended capacitor values. Keep the RS-232 connector-side traces away from sensitive low-level logic where practical. Confirm line rates, cable length, ground continuity, and the system supply level before finalizing the design. This page combines the verified manufacturer description, distributor package information, application guidance, and comparison-oriented design notes to provide practical RS-232 transceiver information beyond a basic catalog listing.

Permintaan RFG Kontak
MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221EAE+T

MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EAE+T is a 1-driver, 1-receiver RS-232 transceiver with a 3 V to 5.5 V single-supply range, AutoShutdown behavior, and enhanced electrostatic-discharge protection. It is packaged in a 16-pin SSOP and is intended for systems that require a single power rail while exchanging data with an RS-232-compatible equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic levels. The MAX3221 belongs to the broader RS-232 interface, communication interface, and interface IC hierarchy. Its integrated charge-pump supply generates the bipolar voltage required by the RS-232 transmitter, allowing operation from a single low-voltage supply rather than a separate positive and negative power rail. The MAX3221E family features automatic shutdown and wake-up behavior. When no valid signal is detected at the receiver inputs, the on-board power supply and drivers can shut down, reducing supply current to approximately 1 µA according to the manufacturer product information. This behavior is useful in battery-powered and intermittently connected equipment because the interface does not need to remain fully powered between communication sessions. The E version adds enhanced electrostatic-discharge protection. The manufacturer lists ±15 kV ESD protection for the MAX3221E, while the MAX3221 product family is designed for EIA/TIA-232 and V.28/V.24 communications. The MAX3221E product page also identifies IEC 61000-4-2 ESD protection for the RS-232 pins. These ratings should be evaluated against the connector placement and system grounding strategy rather than treated as a substitute for external surge protection. Typical uses include industrial serial-port equipment, point-of-sale terminals, data acquisition equipment, configuration interfaces, and legacy peripheral connectivity. The 16-pin SSOP footprint suits compact designs where space is constrained, although connector routing and exposed-charge-pump behavior still require careful PCB planning. The MAX3221E/MAX3223E/MAX3243E family is available from a 3 V supply, with the exact model selection determined by the required number of drivers and receivers. Designers should follow the manufacturer’s recommended charge-pump capacitor connections, place the four external capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog and high-speed digital paths. Receiver and driver enable functions provide local control, while AutoShutdown can reduce power when the remote device is disconnected. The MAX3221EAE+T is therefore best suited to compact, single-supply RS-232 links that require automatic power saving and improved ESD resilience. This page combines the manufacturer family information with practical interface-selection guidance, package-specific implementation considerations, and qualified comparison options for engineers evaluating replacements for the MAX3221EAE+T.

Permintaan RFG Kontak
MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EAE+TG1Z

MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221EAE+TG1Z is a single-channel RS-232 transceiver with one driver and one receiver, 3 V to 5.5 V single-power operation, a maximum data rate of 250 kbps, and enhanced ±15 kV IEC ESD protection in a 16-pin SSOP package. The device also provides automatic shutdown and wakeup functions for power-conscious serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level signals between a computer or embedded controller and the voltage levels used by an RS-232 communications link. Within the interface hierarchy, the MAX3221EAE+TG1Z belongs to the RS-232 transceiver class, where it integrates the line driver, line receiver, charge-pump support, and low-power control functions needed to implement a complete single-channel serial port. Key operating characteristics include a 3 V to 5.5 V supply range, 250 kbps maximum signaling rate, and ±15 kV IEC ESD protection. The automatic shutdown and wakeup features help reduce supply consumption when the associated system is inactive. A low-power supply-current specification of 1 µA is associated with the MAX3221EAE family, supporting battery-operated and energy-conscious equipment designs. The MAX3221EAE+TG1Z uses the MAX3221E 1-driver/1-receiver architecture. Its 16-pin SSOP construction keeps the interface compact while providing the external components and connections required for RS-232 operation. The 250 kbps capability makes it suitable for moderate-speed control links, configuration ports, data acquisition equipment, and service interfaces that do not require modern multi-gigabit serial communication. Typical applications include industrial control and instrumentation, data acquisition systems, test and measurement equipment, embedded serial adapters, and point-of-sale or peripheral interfaces. Automatic shutdown is particularly useful in portable and remotely powered systems where the serial transceiver can remain present on the board without maintaining a continuously active internal state. The integrated ESD protection improves interface robustness when cables connect the board to external equipment. A key design consideration is the distinction between the logic-side supply and the RS-232 line-side operating requirements. Confirm capacitor selection, charge-pump operation, logic levels, and shutdown-control polarity against the manufacturer datasheet before layout release. Place the required charge-pump and bypass capacitors close to their designated pins, and keep the RS-232 connector and interface traces physically separated from sensitive analog or high-speed digital nets. This page consolidates the verified electrical identity, package details, interface characteristics, drop-in alternatives, and application guidance for the MAX3221EAE+TG1Z. It also highlights practical distinctions among same-family and cross-brand RS-232 interface options so engineers can select a part based on package fit, supply range, data rate, shutdown behavior, and protection requirements rather than by partial parameter similarity alone.

Permintaan RFG Kontak
MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECAE+T

MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221ECAE+T is a single-driver, single-receiver RS-232 transceiver operating from 3.0V to 5.5V at up to 250kbps in a 16-pin SSOP package. It integrates a charge-pump voltage converter, automatic shutdown and wake-up, and ±15kV ESD protection for compact, low-power serial-interface designs. An RS-232 transceiver is a semiconductor interface that converts logic-level TTL or CMOS signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. Positioned within the interface IC and power-management hierarchy, the MAX3221 supports point-to-point serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment. The MAX3221 uses one transmitter and one receiver, making it suitable for serial links requiring a single bidirectional channel. Its 3.0V to 5.5V supply range permits operation from both 3.3V and 5V systems. AutoShutdown reduces supply current to approximately 1µA when the receiver detects no valid signal, helping conserve power in intermittently connected equipment. The integrated charge-pump circuitry develops the positive and negative voltages required by RS-232 without a separate power supply. Enhanced electrostatic-discharge protection is rated at ±15kV, an important consideration for exposed cables and connectors. The interface also operates at up to 250kbps, covering conventional asynchronous RS-232 communication rates while providing margin for modern firmware-based protocols. Typical uses include RS-232 configuration ports on industrial controllers, test and measurement equipment, POS terminals, serial adapters, and embedded systems communicating with legacy peripherals. Because RS-232 is a single-ended, unbalanced standard, cable routing and grounding remain important, and long cables should be treated as potential sources of noise and ESD events. Place the charge-pump capacitors and transceiver-side bypass capacitor close to their associated pins. Keep the RS-232 connector interface path physically separate from sensitive logic, and route the ground return appropriately for the installed cable. Verify baud-rate, logic-level, and supply compatibility before replacing another transceiver. This page combines the manufacturer's RS-232 interface specifications, package information, sourcing guidance, and practical implementation considerations. It also organizes pin-compatible alternatives and explains where their ESD, power-management, and temperature-grade differences matter during component selection.

Permintaan RFG Kontak