Interface Transceivers
Produk (4)
MAX202EEUE+T - 120kbps 5V RS-232 | Analog Devices
Analog Devices MAX202EEUE+T is a 5V RS-232 transceiver with two driver and two receiver channels, data rates up to 120kbps, and ±15kV ESD protection in a 16-pin TSSOP package. The MAX202E family supports single-supply operation through integrated charge-pump circuitry and complies with EIA/TIA-232E and CCITT V.28 requirements. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial port. Its drivers translate low-voltage logic levels into RS-232 bipolar levels, while its receivers perform the reverse conversion. The MAX202EEUE+T belongs to the RS-232 transceiver hierarchy, which also includes line drivers, line receivers, interface controllers, and broader communication interface semiconductors. The two-driver, two-receiver arrangement supports full-duplex serial communication through two data channels. Its 120kbps maximum data rate provides sufficient margin for common serial links while meeting the EIA/TIA-232E and CCITT V.28 specifications identified by Analog Devices. Integrated charge-pump circuitry generates the bipolar voltage required by RS-232 drivers from a single +5V supply, reducing the external power-supply complexity associated with older interface designs. ESD protection is a central feature of this device. The manufacturer describes the MAX202E family as having ±15kV Human Body Model ESD protection, making the interface suitable for systems where cables and connectors can be exposed to electrostatic discharge. The MAX202EEUE+T combines that protection with integrated charge-pump operation in a compact 16-pin TSSOP package suited to dense industrial, instrumentation, and embedded-control equipment. Typical uses include serial service ports, test and measurement equipment, industrial controllers, data-acquisition systems, and embedded systems that exchange data with RS-232 peripherals. Two channels can connect separate transmit and receive paths, while full-duplex operation allows the endpoint to send and receive simultaneously. The 120kbps rate is especially appropriate for configuration interfaces, diagnostic links, and legacy equipment connectivity rather than high-volume local-area networking. When laying out a design, place the charge-pump capacitors and interface bypass capacitors close to their designated pins, and route the RS-232 traces away from sensitive analog or high-speed digital signals. Treat the external connector as an ESD entry point, use a suitable chassis and signal-ground strategy, and verify the complete interface against the system grounding requirements. The manufacturer datasheet is the authoritative source for pin assignment, capacitor values, and test conditions. This product page combines the confirmed MAX202E specifications with package, sourcing, replacement, and design guidance. It also distinguishes true pin-compatible drop-in options from family members that use different packages, helping engineers avoid incorrect substitutions when reusing an existing PCB layout.
MAX211IDBG4 - 5V Multichannel RS-232 Transceiver | Texas Instruments
The Texas Instruments MAX211IDBG4 is a 5 V multichannel RS-232 line driver/receiver with four drivers, five receivers, operation up to 120 kbit/s, and ±15 kV human-body-model ESD protection, housed in a 28-pin SSOP package. The device also includes a dual charge-pump circuit, allowing the RS-232 transmit outputs to generate the required negative and positive voltage levels from a single supply. An RS-232 transceiver is an interface integrated circuit that combines logic-level driver and receiver functions with the voltage conversion required by the RS-232 standard. Within the signal-chain hierarchy, the MAX211IDBG4 belongs to the RS-232 interface IC class, connecting low-voltage digital systems to external serial ports. It is designed for equipment requiring multiple serial channels while conserving board space through a narrow surface-mount package. The MAX211IDBG4 operates from a 5 V supply and contains four RS-232 drivers and five receivers. Its maximum signaling rate is 120 kbit/s, making it appropriate for legacy serial-console, industrial-control, point-of-sale, and embedded-system connections. The listed ±15 kV HBM ESD protection applies to the serial-port connection pins, including ground, while shutdown operation reduces supply current to a typical 1 µA. Its dual charge-pump circuit generates the bipolar voltage levels used by RS-232 drivers from the 5 V supply. The device is specified to meet or exceed TIA/EIA-232-F and ITU V.28 requirements. This combination of integrated level translation, four transmit channels, five receive channels, and low-power shutdown makes the part useful where multiple serial interfaces must coexist on one board. Typical applications include multiport serial adapters, industrial controller interfaces, test equipment, POS terminals, and embedded debug systems. The five receivers also permit one incoming line to be monitored while four other channels are active. Designers should account for the charge-pump capacitors and ensure that signal routing, grounding, and connector protection preserve the specified ESD and communication performance. For a robust layout, place the charge-pump capacitors and interface bypass capacitor close to their associated pins, route transceiver outputs directly toward the connector, and maintain a low-impedance ground return. The 28-pin SSOP footprint reduces board area, but careful fan-out and signal-return management remain important because RS-232 uses single-ended signaling over relatively slow, long cable links. This page combines the device's principal electrical characteristics, verified source links, interface-design guidance, and selection criteria for engineers evaluating the MAX211IDBG4 in multichannel RS-232 systems.
MAX232ACWE+T - 116kbps Dual RS-232 Transceiver | Analog Devices
The Analog Devices MAX232ACWE+T is a dual RS-232 line transceiver with two drivers and two receivers, a maximum data rate of 116 kbps, and operation from a 5.5 V supply. The device is housed in a 16-pin wide SOIC-16W surface-mount package and is supplied in tape-and-reel packaging. It is intended for EIA/TIA-232E and V.28/V.24 serial interfaces where ±12 V is unavailable. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. Within the signal-chain hierarchy, the MAX232 belongs to the RS-232 interface transceiver class, combining transmitter, receiver, and voltage-generation functions in one package. This integration allows a compact equipment port to communicate with legacy serial equipment without requiring a separate external charge-pump supply. The MAX232ACWE+T provides two transmit channels and two receive channels in one device. Its listed 116 kbps data rate is suitable for conventional asynchronous serial communication rather than high-speed differential buses such as RS-485. The 5.5 V supply requirement permits operation in systems where only a positive 5 V rail is readily available. Its dual-channel organization also reduces component count when two RS-232 ports must share the same logic interface. The MAX232 family is designed for EIA/TIA-232E and V.28/V.24 communication interfaces, including equipment where ±12 V cannot be supplied. The integrated line-driver and receiver functions provide the electrical interface between CMOS/TTL-compatible logic and RS-232 lines. Device variants exist in multiple package and temperature options, so engineers should confirm the exact ordering suffix when matching a board footprint and environmental requirement. Typical uses include industrial control consoles, laboratory instrumentation, point-of-sale equipment, service interfaces, embedded serial ports, and data-acquisition systems. A two-driver, two-receiver arrangement is especially useful when one equipment enclosure must support two independent RS-232 links or combine full-duplex operation on two ports. PCB design should preserve the pin arrangement defined by the SOIC-16W footprint and follow the capacitor and charge-pump guidance in the manufacturer data sheet. Keep the interface connector, protection network, and transceiver on a controlled impedance-free point-to-point RS-232 path, and provide suitable grounding rather than relying on the logic ground as a substitute for a proper cable shield connection. This page combines the exact MAX232ACWE+T ordering information, verified manufacturer specifications, sourcing guidance, interface-use guidance, and a careful review of drop-in alternatives. It is intended to help engineers identify the correct package variant, evaluate replacement options, and implement a robust RS-232 interface without overlooking footprint or qualification differences.
TJA1051ATK/3/0Z - 5Mbps CAN Transceiver | NXP | Automotive
The NXP Semiconductors TJA1051ATK/3/0Z is a single-channel high-speed CAN transceiver with one transmit and one receive channel, a maximum data rate of 5 Mbps, a 4.5 V to 5.5 V supply range, and an 8-HVSON package measuring 3 mm by 3 mm. It is designed to connect a CAN protocol controller to a physical two-wire CAN bus in automotive and industrial electronic systems. A CAN transceiver, also called a CAN physical-layer interface, belongs to the interface-transceiver class of semiconductor devices. It converts the logic-level transmit and receive signals used by a CAN controller into the differential CANH and CANL signals carried by a two-wire bus. This physical-layer function complements the protocol processing performed by a CAN controller, while a terminating network, common-mode choke, surge protection, and correctly designed PCB routing complete the bus interface. The TJA1051ATK/3/0Z combines differential transmit and receive capability with a maximum CAN data rate of 5 Mbps. Its 4.5 V to 5.5 V operating supply range supports regulated 5 V logic systems, while the specified -40 °C to 150 °C temperature range covers demanding automotive environments. The compact 8-HVSON package reduces board area, and the package configuration identified in distributor catalogs as 8-HVSON (3 x 3) supports high-density controller and communication electronics. The transceiver provides the physical interface between a microcontroller-based CAN controller and the bus wiring. Its transmitter drives the differential CANH and CANL pair, while its receiver converts the bus differential voltage into a logic-level RXD signal for the controller. The TXD input accepts the controller's transmit command, allowing protocol firmware to arbitrate access, acknowledge frames, and manage fault recovery across the network. Typical uses include automotive body electronics, engine-control units, gateways, industrial automation controllers, embedded communications modules, and other equipment using high-speed CAN. The device is particularly suitable where a compact interface is needed alongside a 5 V CAN controller. Final system compatibility still depends on bus topology, termination, transceiver timing, electromagnetic-compatibility requirements, and the electrical limits of the connected nodes. For PCB implementation, place the transceiver close to the CAN connector or protected bus-entry section, provide a continuous ground reference, and route CANH and CANL as a tightly coupled differential pair. Follow the manufacturer datasheet for exposed-pad soldering, decoupling, bus protection, and component spacing. Keeping the high-current return path away from sensitive control signals helps reduce common-mode conversion and improves EMC behavior in automotive or industrial installations. This product page combines the exact orderable MPN, package identification, operating limits, datasheet access, replacement guidance, application guidance, and practical PCB-design considerations. It is intended to help engineers identify the correct variant, plan the hardware, and evaluate alternatives without changing the existing 8-HVSON footprint unnecessarily.