Produk (21.000+)

LPC11A02UK - 50MHz ARM Cortex-M0 MCU | NXP | WLCSP-20
LPC11A02UK

LPC11A02UK - 50MHz ARM Cortex-M0 MCU | NXP | WLCSP-20

The NXP Semiconductors LPC11A02UK is a 50 MHz, 32-bit Arm Cortex-M0 microcontroller with 16 kB of Flash memory and 4 kB of SRAM, housed in a 20-WLCSP package. It is designed for compact embedded products that need efficient control processing, mixed-signal sensing, and low power operation in a very small footprint. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one component. The LPC11A02UK belongs to the LPC11Axx family of low-cost 32-bit MCUs and uses the Arm Cortex-M0 architecture, which provides a compact instruction set for responsive embedded control. Its 16 kB Flash supports firmware storage, while its 4 kB SRAM provides working memory for control routines and data buffers. Key features include operation up to 50 MHz, a 1-bit ADC, a 10-bit DAC, an analog comparator, a temperature sensor, an internal voltage reference, and under-voltage lockout protection. The verified distributor information identifies the device as a WLCSP-20 packaged microcontroller with 18 I/O ports and a supply voltage range of 2.6 V to 3.6 V. These features allow the MCU to support sensing, actuator control, monitoring, and low-speed communication tasks within a compact embedded design. The LPC11A02UK uses a 32-bit Arm Cortex-M0 processor and is positioned as a low-cost member of the LPC11Axx microcontroller family. The Cortex-M0 core is suitable for deterministic, compact embedded-control code where simplicity, low silicon cost, and compact packaging matter. The device combines digital control with configurable analog and mixed-signal peripherals, allowing one MCU to supervise sensors, drive outputs, and manage local system conditions. Typical applications include battery-powered sensor nodes, compact industrial monitoring modules, consumer accessories, small motor-control subsystems, and embedded control boards. The 20-WLCSP package is especially useful where PCB area is constrained. Designers should confirm the exact ball map, exposed-pad requirements, supported peripherals, and pin multiplexing against the manufacturer datasheet before laying out a new PCB or replacing another device. This page consolidates verified manufacturer and distributor information, package details, application guidance, and purchasing considerations. Pricing and availability can change by quantity and supplier, so procurement should be confirmed against current distributor listings. For replacements, pin compatibility and peripheral equivalence must be verified rather than inferred from the family name alone. The LPC11A02UK is an active NXP product suitable for engineers seeking a compact Arm Cortex-M0 controller with integrated sensing and monitoring functions. Its principal trade-offs are small package availability, limited memory compared with larger MCUs, and the need for careful board-level validation around the 20-WLCSP footprint.

Permintaan RFG Kontak
LPC11A04UK - 50MHz Cortex-M0 MCU, 32KB Flash | NXP
LPC11A04UK

LPC11A04UK - 50MHz Cortex-M0 MCU, 32KB Flash | NXP

The NXP Semiconductors LPC11A04UK is a low-cost, 32-bit Arm Cortex-M0 microcontroller operating up to 50 MHz, with 32 KB of Flash, 8 KB of SRAM, and 4 KB of EEPROM in a 20-WLCSP package measuring 2.55 mm by 2.55 mm. The verified distributor data identifies an 18-I/O device and configurable analog or mixed-signal resources for compact embedded control designs. A microcontroller is a programmable system-on-chip that integrates a CPU core, nonvolatile program memory, working memory, peripherals, and input/output into one package. The LPC11A04UK belongs to the MCU, embedded processor, semiconductor, and Arm Cortex-M0 hierarchy. It targets cost-sensitive control, sensing, communication, and actuator functions where deterministic low-power behavior and compact packaging are valuable. The LPC11A04 family operates at CPU frequencies up to 50 MHz and includes a Nested Vectored Interrupt Controller, a system tick timer, Serial Wire Debug, an ISP and IAP-capable on-chip bootloader path, and up to 16 kB of boot ROM according to the verified Keil device record. Its memory combination supports compact firmware, working state, and retained parameters without requiring external memory for many designs. NXP describes the LPC11Axx family as a scalable entry-level MCU family with a low-cost 32-bit instruction set and software-configurable analog and mixed-signal subsystems. The architecture is suitable for small control loops, but designers should verify the exact peripheral set, clock limits, pin multiplexing, and electrical limits against the official device documentation before releasing a PCB. Typical uses include low-power sensor nodes, simple motor-control helpers, compact industrial controls, consumer accessories, and connected embedded products. The 20-WLCSP package supports dense layouts, while its small ball pitch and exposed thermal and routing complexity make careful PCB assembly and inspection important. The principal design trade-off is integration versus inspection risk. The LPC11A04UK consolidates processing, memory, GPIO, and configurable analog functions into a tiny package, reducing board area but increasing sensitivity to pad geometry, solderability, and layout quality. This page combines the supplied manufacturer and distributor records, pricing evidence, package details, design guidance, and verified cross-reference findings. It also distinguishes documented facts from missing technical data instead of estimating electrical limits, pin functions, or drop-in alternatives that the supplied sources do not establish.

Permintaan RFG Kontak
LPC11C14FBD48/301 - 32KB Flash Cortex-M0 MCU w/ CAN | NXP
LPC11C14FBD48/301

LPC11C14FBD48/301 - 32KB Flash Cortex-M0 MCU w/ CAN | NXP

The NXP LPC11C14FBD48/301 is an ARM Cortex-M0 based 32-bit microcontroller running at up to 50 MHz, with 32 KB of on-chip flash, 8 KB of SRAM, and an integrated C_CAN controller, housed in a 48-pin LQFP (7x7 mm) package. It belongs to the LPC1100 series, designed as a low-cost upgrade path for 8/16-bit MCU applications, offering higher performance with a simple Thumb/Thumb-2 instruction set and reduced code size compared to legacy architectures. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (flash), volatile data memory (SRAM), and peripherals such as timers, communication interfaces, and analog blocks into one package. MCUs sit at the bottom of the embedded computing hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor device. The Cortex-M0 class represents the smallest, lowest-power variant of the ARMv6-M architecture, with deterministic interrupt handling that makes it well-suited for real-time control. The on-chip C_CAN conforms to the ISO 11898-1 CAN 2.0B standard, eliminating the need for an external CAN transceiver controller in bus-node designs. Key features include a 50 MHz Cortex-M0 core with single-cycle multiplier, 32 KB flash with In-System Programming (ISP) and In-Application Programming (IAP), 8 KB SRAM, a 12 MHz internal RC oscillator trimmable to 1% accuracy, an integrated C_CAN 2.0B controller, one SSP/SPI, one I2C, one UART, four general-purpose timers, a 10-bit ADC with up to 8 input channels, and a windowed watchdog timer. Power consumption is rated at approximately 10 mA active and 1 mA in deep-sleep mode at 3.3 V. The architecture uses a 3-stage pipeline with the ARMv6-M Thumb instruction set. Code density is significantly improved over 8/16-bit cores, allowing more functionality in the same 32 KB flash budget. The integrated C_CAN block uses 256-byte message RAM, supporting both standard (11-bit) and extended (29-bit) identifiers, which simplifies fieldbus node designs. The 12 MHz IRC can be trimmed in software to within 1% across the full operating range, often eliminating the need for an external crystal. Typical applications include CAN node endpoints in industrial automation, e-metering and smart metering, LED lighting controllers, alarm system panels, white goods, sensor hubs, and low-cost building-automation gateways. The integrated CAN controller is the standout feature in this price/performance class - the part is positioned wherever an 8-bit MCU is being replaced but a CAN interface is also required. When designing with this MCU, place a 100 nF decoupling capacitor adjacent to each VDD pin and connect all VSS pins to a solid ground plane to reduce digital switching noise coupling into the ADC. The CAN TXD/RXD lines still require an external 3.3 V CAN transceiver such as the TJA1050 or SN65HVD230 to drive the bus. This page synthesizes distributor pricing, drop-in LPC11xx alternatives, design notes, and application guidance that is not consolidated in the manufacturer datasheet, helping engineers and procurement teams evaluate the LPC11C14FBD48/301 in a single view.

Permintaan RFG Kontak
LPC11E66JBD48E - 50MHz Cortex-M0+ MCU 64KB Flash | NXP
LPC11E66JBD48E

LPC11E66JBD48E - 50MHz Cortex-M0+ MCU 64KB Flash | NXP

The NXP LPC11E66JBD48E is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 50 MHz CPU frequency, integrating 64 KB of flash, 12 KB of SRAM, and 4 KB of on-chip EEPROM, housed in a 48-pin LQFP (7x7 mm) package. It is part of the LPC11Exx family, a low-cost 32-bit MCU series designed as a stepping stone from 8/16-bit architectures to modern Cortex-M performance with a simple instruction set that minimizes code size. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data memory, peripherals, and I/O. The ARM Cortex-M0+ is ARM's smallest and most energy-efficient Cortex-M core, designed for deterministic embedded control. Loaders live in the broader hierarchy: Cortex-M0+ -> ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The LPC11Exx family targets applications transitioning from 8/16-bit MCUs by providing modern performance with familiar low-pin-count packages. Key features include a 12-bit ADC for sensor digitization, multiple serial interfaces (USART, SPI, I2C), PWM outputs for motor or LED control, and configurable GPIO. The integrated EEPROM (4 KB) eliminates the need for an external non-volatile memory chip for parameter storage, lowering BOM count. The 50 MHz CPU frequency provides ample headroom for protocol stacks and real-time control loops. Architecturally, the LPC11E66 uses the Cortex-M0+ core paired with a configurable AHB bus matrix, low-power peripherals, and a programmable ROM-based boot loader that supports in-system programming via UART or USB ISP. This combination allows field firmware upgrades without external programmers, which is valuable for deployed industrial and consumer products. Typical applications include home appliances, white goods, motor control peripherals, building automation nodes, low-cost sensor hubs, and consumer electronics requiring USB or CAN connectivity through on-chip interfaces. The wide operating voltage range (typically 1.8V-3.6V core) supports battery-powered devices. When designing with this MCU, ensure the decoupling network uses 100 nF X7R ceramics on each VDD/VDDA pin placed within 2 mm of the pad. Leave the ISP entry pin accessible (typically PIO0_1) to enable in-field firmware updates without disassembly. This page synthesizes distributor pricing, drop-in alternatives from NXP LPC11Exx family, and practical design notes not consolidated in the manufacturer datasheet, giving procurement and engineering teams a single reference for the LPC11E66JBD48E.

Permintaan RFG Kontak
LPC11E67JBD48E - 50MHz Cortex-M0+ MCU | NXP
LPC11E67JBD48E

LPC11E67JBD48E - 50MHz Cortex-M0+ MCU | NXP

NXP Semiconductors LPC11E67JBD48E is a 32-bit Arm Cortex-M0+ microcontroller in the LPC11Exx family, operating at up to 50 MHz with 128 KB of flash memory in a 48-LQFP package measuring 7 mm by 7 mm. The part is listed as active, providing a compact platform for cost-sensitive embedded control, sensor acquisition, actuator control, and connected industrial equipment. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Cortex-M0+ architecture belongs to the Arm microcontroller hierarchy and is designed for efficient, low-complexity control applications. NXP describes the LPC11Exx family as a low-cost 32-bit MCU family intended to replace 8-bit and 16-bit architectures while reducing code size through its efficient instruction set. The LPC11E67JBD48E therefore combines familiar microcontroller operation with a 32-bit processing architecture and a 50 MHz clock capability. The three defining parameters are a maximum CPU frequency of 50 MHz, 128 KB of flash memory organized as 128K by 8 bits, and a 48-LQFP package with a 7 mm by 7 mm body. Its ARM Cortex-M0+ core supports embedded software workflows that require deterministic control, peripheral integration, and moderate arithmetic performance. The 128 KB program-memory region is suitable for firmware, configuration handling, and application logic in compact industrial, consumer, and embedded-control products. The LPC11Exx positioning emphasizes a simple instruction set and code efficiency rather than high-end application-processing performance. That balance makes the LPC11E67JBD48E appropriate for controllers that repeatedly perform sensing, control, communications, and local supervision. At 50 MHz, the device provides additional timing headroom for interrupt-driven and mixed-control workloads while retaining the resource profile associated with an entry-level 32-bit MCU. Typical uses include building automation controls, temperature and environmental monitoring, small motor-control subsystems, industrial sensor hubs, appliance controllers, and low-cost connected peripherals. The 48-LQFP package exposes more pins than a minimal small-outline package, making the device suitable for designs that need a balance of peripheral access, compact board area, and assembly cost. Pin assignment and peripheral multiplexing must be checked against the manufacturer pin description and device data sheet before PCB routing. The principal design consideration is to verify the complete pin configuration, supported voltage range, clock setup, and peripheral assignments in the manufacturer documentation. Because this MCU family is intended for broad embedded use, firmware partitioning, watchdog behavior, reset handling, and low-power transitions should be established early. Decoupling, programming access, clock jitter, and unused-pin handling also need to follow the device's recommended hardware guidelines. This product page combines the NXP family positioning, distributor package and memory details, an exact-package replacement check, application guidance, and engineering-focused design notes. These resources help engineers evaluate the LPC11E67JBD48E before committing a compact control board to the LPC11Exx architecture.

Permintaan RFG Kontak
LPC11E67JBD48K - 32-Bit 50MHz Cortex-M0+ MCU | NXP
LPC11E67JBD48K

LPC11E67JBD48K - 32-Bit 50MHz Cortex-M0+ MCU | NXP

NXP Semiconductors LPC11E67JBD48K is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50 MHz, with 128 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the LPC11Exx family, a scalable entry-level MCU range designed to replace 8-bit and 16-bit designs while retaining a simple instruction set and efficient code footprint. The verified manufacturer listing identifies this orderable variant as active. A microcontroller is an integrated circuit containing a processor core, program Flash, data memory, peripherals, and interface logic on one semiconductor device. The ARM Cortex-M0+ core provides a compact instruction set and deterministic embedded-control architecture. Within the product hierarchy, the LPC11E67JBD48K is an ARM-based microcontroller, an embedded processor, and a semiconductor intended for cost-sensitive control applications. The LPC11E67JBD48K combines a maximum 50 MHz operating frequency with 128 KB of Flash organized as 128K x 8. This combination supports firmware storage while avoiding the memory cost and board area of a larger microcontroller package. The 48-LQFP 7 x 7 mm package offers a surface-mount solution with a comparatively compact body, although its lead pitch must be accommodated by the PCB land pattern and assembly process. The LPC11Exx family also includes devices with up to 256 kB Flash, 36 kB SRAM, and 4 kB EEPROM according to the verified datasheet listing. A 12-bit ADC is identified in the same source. Device-specific ADC, SRAM, EEPROM, clock, and peripheral details must be confirmed in the manufacturer datasheet before assigning pins or calculating firmware resource requirements. Typical uses for this microcontroller class include compact industrial controllers, building and access-control equipment, appliance controls, sensing nodes, and low-cost embedded products. The 50 MHz Cortex-M0+ performance is useful for responsive control loops and moderate protocol handling, while the 128 KB Flash capacity allows application firmware and configuration data to be stored locally. Designers should verify the exact LPC11E67JBD48 pin assignments, peripheral multiplexing, clock limits, decoupling requirements, and exposed-pin treatment in the NXP datasheet. The verified web results do not provide a complete public pin table, so this record does not infer pin names or provide a fabricated package diagram mapping. PCB design and firmware bring-up should also account for the LQFP lead geometry rather than a leadless QFN footprint. This product record combines current NXP lifecycle information, distributor inventory and pricing evidence, family-level technical data, strict data-availability markers, and procurement guidance. It distinguishes verified device facts from parameters that still require confirmation, helping engineers avoid treating broader LPC11Exx family capabilities as guaranteed LPC11E67JBD48K specifications.

Permintaan RFG Kontak
LPC11E67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP
LPC11E67JBD64E

LPC11E67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP

NXP Semiconductors LPC11E67JBD64E is a 32-bit ARM Cortex-M0+ microcontroller with a 50 MHz maximum CPU frequency, 128KB of flash memory, and 20KB of SRAM in a 64-pin LQFP package measuring 10 mm by 10 mm. It belongs to the LPC11Exx scalable entry-level MCU family, combining an efficient ARM Cortex-M0+ core with embedded flash, SRAM, and mixed-signal peripherals in one compact surface-mount package. An ARM Cortex-M0+ microcontroller is a compact embedded-processing device used to execute firmware, read sensors, control outputs, and manage communication peripherals. The LPC11Exx family sits within the broader hierarchy of microcontroller, embedded processor, semiconductor, and embedded-control systems. Its 32-bit architecture provides an efficient platform for cost-sensitive products requiring deterministic real-time control without the resources of a higher-performance Cortex-M processor. The LPC11E67JBD64E provides 128KB of flash for program storage and 20KB of SRAM for data, stack, and working memory. Its maximum CPU frequency is 50 MHz. The device is supplied in a 64-LQFP package, providing 64 external pins for power, ground, resets, clock inputs, and peripheral connections. The verified distributor information also identifies the device as a 3.3 V part and as a member of the LPC11Exx family. Detailed GPIO allocation, operating-temperature limits, and individual peripheral characteristics remain subject to the manufacturer datasheet. The ARM Cortex-M0+ core supports a compact instruction set optimized for embedded control, while the integrated memory allows firmware and working data to share a single package and PCB footprint. This integration reduces component count and simplifies board routing compared with a discrete processor-plus-memory implementation. The 50 MHz operating rate provides useful headroom for protocol handling, digital control loops, and supervisory tasks while maintaining a low-complexity architecture. Typical uses include industrial control modules, sensor-hub boards, communication equipment, building automation, appliance controllers, and compact embedded data-acquisition products. The 128KB flash capacity is suitable for moderate firmware images, while 20KB SRAM supports networking stacks and control buffers without requiring external memory. Its 64-LQFP package also makes the device accessible for prototype assembly and conventional surface-mount manufacturing. Designers should verify the complete pin assignment, peripheral multiplexing, and electrical limits against the manufacturer datasheet before layout release. The 3.3 V supply requirement should be paired with appropriate decoupling and signal-level planning for connected modules. Because exact GPIO, timing, temperature, and qualification data were not included in the verified results, those values should not be inferred from the family description alone. This product record combines verified distributor specifications, official manufacturer identification, package information, sourcing references, and engineering-focused selection guidance. It also distinguishes the LPC11E67JBD64E from higher-memory family variants and documents the limited number of confirmed pin-compatible alternatives rather than presenting unverified substitutes as drop-in devices.

Permintaan RFG Kontak
LPC11E68JBD48E - 50MHz Cortex-M0+ 256KB MCU | NXP
LPC11E68JBD48E

LPC11E68JBD48E - 50MHz Cortex-M0+ 256KB MCU | NXP

The NXP Semiconductors LPC11E68JBD48E is a low-cost 32-bit microcontroller based on the Arm Cortex-M0+ processor, operating at up to 50 MHz, with 256 KB of flash memory, 36 KB of SRAM, and 48 leads in a 7 x 7 mm LQFP package. It belongs to the LPC11Exx family, which targets cost-sensitive designs that need more processing capability and memory than traditional 8-bit or 16-bit microcontrollers. A microcontroller is a compact programmable system containing a processor core, nonvolatile program memory, volatile data memory, and integrated peripherals. The LPC11Exx family combines a simple instruction set with 32-bit processing, enabling efficient control firmware for industrial, embedded-control, communications, and sensing products. Its low-cost positioning helps reduce system complexity when a more capable processor is unnecessary. The LPC11E68JBD48E provides 256 KB of flash for firmware and 36 KB of SRAM for working data. A 50 MHz CPU clock supports responsive execution of control tasks, state machines, and communication routines. The 48-LQFP package provides 48 external connections and a 7 x 7 mm body size, making the device appropriate for compact boards assembled with conventional leaded surface-mount processes. The Arm Cortex-M0+ architecture uses a compact instruction set designed for embedded applications. Compared with an 8-bit MCU, the 32-bit architecture offers a larger addressing space and higher processing throughput. The NXP LPC11Exx family is specifically positioned as a cost-conscious bridge between conventional 8-bit and 16-bit controllers and more complex 32-bit processors. Typical uses include industrial equipment controllers, sensor-interface systems, building automation, compact communication modules, and low-cost consumer appliances. A design can use the 256 KB flash region for application firmware and the 36 KB SRAM for working variables, buffers, and peripheral data. The 50 MHz operating frequency also permits moderate protocol handling and real-time control without moving to a higher-power processor class. PCB design should preserve short return paths for power and ground and place decoupling capacitors close to the supply pins. Because the package has 48 gull-wing leads, assembly and inspection are simpler than with fine-pitch BGA packages, although board area remains greater than for a compact leadless package. Confirm the complete pin assignment, voltage limits, and peripheral multiplexing in the NXP datasheet before layout release. This product page combines the exact LPC11E68JBD48E configuration, package details, lifecycle information, compatible family alternatives, and application-focused design guidance to support component selection and PCB implementation without relying on generic microcontroller descriptions.

Permintaan RFG Kontak
LPC11E68JBD48K - 50MHz Cortex-M0+ 256KB MCU | NXP
LPC11E68JBD48K

LPC11E68JBD48K - 50MHz Cortex-M0+ 256KB MCU | NXP

The NXP LPC11E68JBD48K is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50 MHz, with 256 KB of flash memory and 36 KB of SRAM in a 48-LQFP 7 x 7 mm package. It combines a compact general-purpose MCU architecture with integrated connectivity and embedded-control features for cost-sensitive embedded systems. A microcontroller is a semiconductor device that integrates a CPU core, program memory, data memory, peripherals, and interface controllers on one package. The LPC11E68 belongs to the LPC11Exx family, a low-cost 32-bit MCU platform intended to replace conventional 8-bit and 16-bit designs while providing higher processing performance, efficient code density, and broader peripheral integration. Key device characteristics include a 50 MHz ARM Cortex-M0+ core, 256 KB of flash for firmware, 36 KB of SRAM for working data, and a 48-LQFP package. The 2.4 V to 3.6 V operating range supports common embedded supply rails, while the compact 7 x 7 mm package supports space-constrained control boards. The LPC11Exx family also targets low-power operation and energy-efficient processing for embedded-control applications. The LPC11Exx architecture uses the ARM Cortex-M0+ instruction set, which provides deterministic 32-bit processing while maintaining code density appropriate for small embedded systems. Its combination of flash, SRAM, serial interfaces, timers, and GPIO allows one device to consolidate functions that might otherwise require several discrete controllers. The LPC11U68 member of the family adds configurable USB connectivity, making it especially relevant when USB connectivity is required. Typical uses include industrial control modules, sensor hubs, building automation controllers, compact instrumentation, appliance controls, and connected low-power peripherals. The 256 KB flash capacity accommodates more complex control firmware and protocol stacks than many entry-level 8-bit controllers, while 36 KB of SRAM provides working space for buffering, state management, and communication routines. Designers should treat the 2.4 V to 3.6 V supply range as the primary electrical boundary and verify every external signal and peripheral setting against the NXP datasheet. PCB layout should provide a stable ground reference, decouple the supply pins near the device, and preserve the package footprint and exposed thermal-pad requirements defined for the selected ordering configuration. This page combines the LPC11E68JBD48K family positioning, exact-ordering details, interface guidance, engineering trade-offs, and verified sourcing information to support faster component selection and PCB design. It also highlights the LPC11U68JBD48K as the closest USB-equipped family comparison for designs that require that connectivity.

Permintaan RFG Kontak
LPC11E68JBD64E - 50MHz Cortex-M0+ MCU, 256KB Flash | NXP
LPC11E68JBD64E

LPC11E68JBD64E - 50MHz Cortex-M0+ MCU, 256KB Flash | NXP

The NXP Semiconductors LPC11E68JBD64E is a 32-bit Arm Cortex-M0+ microcontroller operating up to 50 MHz, with 256 KB of flash memory and 36 KB of SRAM, housed in a 64-LQFP 10 mm × 10 mm package. It is designed for compact embedded systems that require efficient 32-bit processing, substantial code storage, and a broad set of mixed-signal peripherals. The LPC11Exx family combines a simple instruction set, low-power operation, and integrated analog and communication functions in a cost-focused architecture. An Arm Cortex-M0+ microcontroller is a 32-bit embedded processor built around the Armv6-M instruction set. Compared with an 8- or 16-bit controller, the LPC11Exx architecture provides larger addressing capability and more efficient handling of complex control logic. The LPC11E68JBD64E occupies the microcontroller hierarchy as a general-purpose embedded controller with integrated flash, SRAM, analog conversion, timers, serial interfaces, and communication peripherals. Its 50 MHz operating frequency supports responsive control while retaining a compact, low-power design profile. The principal device characteristics include up to 50 MHz CPU operation, 256 KB of flash, 36 KB of SRAM, and 4 KB of EEPROM. A 12-bit ADC supports analog measurement, while the family architecture provides communication capabilities suited to embedded control, sensor acquisition, and connected equipment. The LPC11Exx family was created for applications replacing 8- and 16-bit controllers when greater arithmetic capability, peripheral integration, and reduced firmware complexity are valuable without requiring a higher-tier application processor. The 64-LQFP package provides 64 externally accessible positions and a 10 mm × 10 mm footprint. This relatively large leaded package is suitable for conventional through-hole assembly, prototypes, and designs that benefit from inspectable leads rather than a fine-pitch land pattern. Board layout must preserve access to the ADC inputs, oscillator connections, reset circuitry, programming interface, power rails, decoupling, and all other pins defined in the manufacturer pin-description table. Typical uses include industrial sensing and control, building automation, appliance control, low-cost instrumentation, portable equipment, and embedded subsystems requiring local analog measurement and serial communications. The combination of 256 KB flash and 36 KB SRAM is useful when application firmware, configuration tables, diagnostics, and communication buffers must coexist without external memory. A key design consideration is firmware and peripheral planning. Allocate the ADC pins according to analog-channel requirements, follow the recommended decoupling arrangement, and keep sensitive analog traces away from fast switching nodes. Confirm startup, reset, and programming requirements against the manufacturer datasheet before releasing a PCB. Migration between LPC11Exx devices should also account for differences in USB, memory, peripheral, and temperature-grade options rather than relying on package similarity alone. This page consolidates the confirmed device identity, core memory and timing specifications, package information, sourcing workflow, application context, and verified drop-in alternatives. It also highlights the engineering checks that distinguish a true pin-compatible replacement from a merely similar 64-LQFP microcontroller.

Permintaan RFG Kontak
LPC11U66JBD48E - 50MHz Cortex-M0+ 64KB MCU | NXP
LPC11U66JBD48E

LPC11U66JBD48E - 50MHz Cortex-M0+ 64KB MCU | NXP

NXP Semiconductors LPC11U66JBD48E is a 32-bit Arm Cortex-M0+ microcontroller rated for operation up to 50 MHz, with 64 KB of flash memory in a 48-pin LQFP 7 x 7 mm package. It belongs to the LPC11Uxx family of low-cost, energy-efficient microcontrollers designed as scalable replacements for conventional 8-bit and 16-bit embedded systems. A microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, peripherals, and communication interfaces on one device. The Cortex-M0+ core provides a simple instruction set and compact code footprint, while the LPC11Uxx family combines this processing efficiency with flexible low-power features for embedded control, sensing, and communications equipment. The LPC11U66 provides 64 KB of flash, 12 KB of SRAM, and a maximum CPU frequency of 50 MHz. Its flexible peripheral set is intended to replace several discrete components in cost-sensitive embedded products. The 48-LQFP package exposes the integrated communications and general-purpose peripherals required by protocols, sensors, human-interface equipment, and low-power control systems. The Arm Cortex-M0+ architecture also supports efficient event-driven firmware, helping developers balance processing performance, code density, and energy use. Compared with an 8-bit MCU, the 32-bit processor provides a wider address space and more capable interrupt-driven control. Compared with higher-end Cortex-M systems, the LPC11U66 maintains a low-cost positioning without abandoning 32-bit software development tools. Typical uses include compact industrial controllers, connected sensor nodes, building-control modules, appliance control boards, communications equipment, and embedded access devices. The 48-LQFP package is appropriate for designs that need a moderate number of externally routed pins and a conventional leaded footprint that is easier to inspect and assemble than very fine-pitch packages. Designers should verify the complete pin assignment, peripheral multiplexing, clock configuration, and power requirements against the NXP datasheet before layout release. A stable decoupling network and correct programming-tool configuration are essential for reliable operation. The manufacturer product page identifies LPC11U66JBD48 as active, while distributor listings provide sourcing and packaging information. This page consolidates verified manufacturer information, distributor availability, practical selection guidance, and same-package alternatives for engineers evaluating the LPC11U66JBD48E. It also distinguishes confirmed source data from parameters that still require verification against the full manufacturer datasheet.

Permintaan RFG Kontak
LPC11U67JBD48E - 50MHz 128KB Flash MCU | NXP | USB Cortex-M0+
LPC11U67JBD48E

LPC11U67JBD48E - 50MHz 128KB Flash MCU | NXP | USB Cortex-M0+

NXP Semiconductors LPC11U67JBD48E is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50MHz, with 128KB of Flash memory, 20KB of SRAM, USB connectivity, and a 12-bit ADC in a 48-LQFP (7x7) package. It is designed for cost-sensitive embedded systems that need efficient 32-bit control, flexible peripherals, and USB communication without the power and complexity of a higher-performance Cortex-M core. The LPC11Uxx family belongs to the microcontroller hierarchy: MCU > embedded processor > Arm Cortex-M0+ microcontroller > low-power embedded control. The Cortex-M0+ architecture provides a simple instruction set and efficient code density while retaining a 32-bit processing model. At up to 50MHz, the LPC11U67JBD48E is suitable for connected peripherals, human-interface systems, sensor controllers, and compact consumer or industrial equipment. Verified listings identify 128KB Flash, 20KB SRAM, USB, and a 12-bit ADC. The 48-LQFP (7x7) package provides a conventional leaded footprint that can simplify assembly and prototyping compared with a fine-pitch ball grid array. The 2.4V to 3.6V operating range supports common 3.3V system rails, although the complete electrical limits must be confirmed in the manufacturer datasheet before final design release. The USB capability makes the device useful for USB-to-serial adapters, configuration interfaces, HID peripherals, data acquisition controllers, and service ports. Its ADC supports applications that monitor analog sensors or industrial inputs without requiring a separate converter. The combination of 128KB Flash and 20KB SRAM gives embedded software room for protocol stacks, control logic, buffers, and application code. A typical design places the MCU beside its USB connector, 3.3V regulator, decoupling capacitors, crystal or clock source, and application peripherals. Keep USB differential routing short, controlled-impedance, and away from noisy switching nodes. Confirm oscillator, reset, USB, and peripheral pin assignments against the official datasheet before PCB routing. This page combines verified distributor specifications, sourcing information, application guidance, and same-footprint alternatives for engineering evaluation.

Permintaan RFG Kontak
LPC11U67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP
LPC11U67JBD64E

LPC11U67JBD64E - 50MHz Cortex-M0+ 128KB MCU | NXP

The NXP LPC11U67JBD64E is a 32-bit ARM Cortex-M0+ microcontroller operating at up to 50 MHz, with 128 KB of flash memory and a 64-lead LQFP package measuring 10 mm by 10 mm. The LPC11U67JBD64E belongs to NXP's LPC11Uxx scalable entry-level microcontroller family, combining an economical embedded processor with integrated USB and other connectivity-oriented peripherals. A microcontroller is a semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces into one device. The ARM Cortex-M0+ core provides a compact, energy-efficient architecture for embedded control, while the LPC11Uxx family sits within the broader hierarchy of microcontroller, embedded processor, and semiconductor products. Its 50 MHz operating frequency supports responsive control loops and communication handling without requiring a high-end application processor. The verified device data identifies a 32-bit ARM Cortex-M0+ processor, 128 KB (128K x 8) flash, and a 64-LQFP (10 x 10 mm) package. The E suffix is retained as part of the exact orderable MPN. NXP describes the family as scalable and entry-level, indicating suitability for designs that need broad peripheral integration while controlling system complexity, board area, and cost. Compared with larger Cortex-M microcontrollers, the LPC11U67JBD64E provides a focused 50 MHz Cortex-M0+ platform with 128 KB of embedded flash in a 10 mm square LQFP. The 64-pin package offers more external interface options than smaller lead-count packages, making it useful when a design requires both USB connectivity and additional I/O. Exact SRAM capacity, voltage range, peripheral inventory, and electrical limits require confirmation in the manufacturer datasheet. Typical applications include USB-connected control devices, USB-to-serial adapters, human-interface-interface controllers, compact industrial controllers, instrument-panel controllers, and embedded USB peripherals. The 64-pin package can support a mix of communication, logic, and discrete I/O, while the Cortex-M0+ core handles protocol stacks, sampling, and supervisory tasks in a single device. Designers should verify the exact pin assignments, USB electrical requirements, decoupling network, clock configuration, and exposed programming/debug interfaces against the manufacturer datasheet before layout release. PCB traces, connectors, and protection components must be designed for the device's USB and power specifications. Because no complete public pinout was included in the supplied verified data, no pin-level substitutions should be inferred from this page. This product record combines exact distributor pricing and availability information, same-package family comparisons, and practical engineering guidance. It distinguishes verified facts from parameters that still require datasheet confirmation, helping engineers source the exact LPC11U67JBD64E without confusing a related LPC11E-series device with a guaranteed drop-in replacement.

Permintaan RFG Kontak
LPC11U68JBD100E - 50MHz Cortex-M0+ 256KB MCU | NXP
LPC11U68JBD100E

LPC11U68JBD100E - 50MHz Cortex-M0+ 256KB MCU | NXP

NXP LPC11U68JBD100E is a 32-bit ARM Cortex-M0+ microcontroller operating up to 50 MHz, with 256 KB of embedded flash memory and 36 KB of SRAM, packaged in a 100-pin LQFP. The 14 mm × 14 mm LQFP package provides a high pin count for applications requiring extensive peripheral connectivity and external memory interfacing. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one device. The LPC11U68 belongs to the LPC11Uxx family of scalable, entry-level ARM Cortex-M0+/M0 devices. This MCU family targets cost-sensitive designs that need more processing capability and memory than conventional 8-bit or 16-bit controllers without adopting a higher-cost microcontroller architecture. Key features of the LPC11U68JBD100E include a 50 MHz ARM Cortex-M0+ core, 32-bit processing, 256 KB flash, and 36 KB SRAM. Its 100-pin LQFP package exposes substantially more I/O than small-outline packages, making it useful for systems combining several digital interfaces, analog inputs, communications, or external storage. The MCU is based on the ARM Cortex-M0+ architecture, which emphasizes a simple instruction set and compact code size for embedded control applications. The LPC11Uxx family is designed for low-cost 8-bit and 16-bit microcontroller replacement, smart sensing, metering, communications, and general embedded control. Its operating frequency of up to 50 MHz supports responsive control loops and efficient event-driven firmware. The combination of dedicated program storage, SRAM, and a high-pin-count package allows a single controller to coordinate sensors, communications peripherals, and system I/O without relying on a separate external processor. Typical uses include electronic meters, building-control endpoints, industrial sensing modules, low-power monitoring equipment, connected accessories, and embedded control boards. Engineers can evaluate the device with Arm Keil tooling through the LPC11U68 CMSIS device family package, while NXP's LPCXpresso environment provides a path for development and debugging. The principal design consideration is that the 100-pin LQFP requires a substantially larger PCB footprint than 32-pin or 48-pin MCUs. Use the package drawing and pin table from the manufacturer documentation when assigning tracks, and confirm peripheral multiplexing before finalizing the board layout. This product page combines the manufacturer identification, key memory and processor specifications, package information, practical application guidance, and a qualified comparison of parts considered for replacement. It is intended to help engineers make an initial suitability decision while preserving the need to validate electrical, timing, software, and lifecycle requirements against current manufacturer documentation.

Permintaan RFG Kontak
LPC11U68JBD48E - 50MHz Cortex-M0+ MCU | NXP
LPC11U68JBD48E

LPC11U68JBD48E - 50MHz Cortex-M0+ MCU | NXP

The NXP Semiconductors LPC11U68JBD48E is an active 32-bit ARM Cortex-M0+ microcontroller operating at up to 50 MHz, with 256 KB of flash program memory and 36 KB of RAM in a 48-pin LQFP package measuring 7 mm by 7 mm. It is designed for compact embedded systems that need efficient control processing, flexible peripherals, and a low-cost general-purpose architecture. An ARM Cortex-M0+ microcontroller is a reduced-instruction-set processor used to manage sensors, communications, actuators, and human-machine interfaces. The M0+ architecture combines an Arm processing core with deterministic embedded control, while flash memory stores firmware and RAM supports working data. Within the product hierarchy, the LPC11U68JBD48E is an MCU, an embedded processing IC, and a member of NXP's LPC11Uxx family. Key device characteristics include a 50 MHz maximum CPU frequency, 256 KB flash, 36 KB RAM, and operation from a 3.3 V supply as listed for the exact device. The 48-LQFP package provides a conventional leaded surface-mount footprint and is easier to inspect than a very fine-pitch package. The manufacturer lists LPC11U68JBD48 as active, while the LPC11U68JBD48E ordering code identifies the extended-temperature variant. The device's combination of 32-bit processing, substantial embedded memory, and a 50 MHz clock is useful for protocol handling, digital control, data acquisition, and connected peripherals. Its compact instruction set supports compact firmware while retaining the software ecosystem associated with Arm Cortex-M processors. Developers can use the same core architecture as a common platform element across sensors, communications modules, and industrial control products. Typical uses include industrial monitoring, building-control endpoints, low-cost connectivity modules, sensor nodes, and compact consumer accessories. A 3.3 V operating supply simplifies integration with common embedded peripherals, while 256 KB of flash provides room for application code, configuration data, and boot routines. The 36 KB RAM supports buffering and real-time state management without requiring an external memory device. Designers should verify the complete pin description, clock requirements, power sequencing, and peripheral multiplexing in the NXP datasheet before layout release. The 48-pin LQFP footprint should be checked against the exact E suffix ordering code, and firmware should be built against the matching LPC11Uxx device configuration. Temperature limits, decoupling, and programming-test requirements should also follow the manufacturer guidance for the selected package variant. This product page combines the exact orderable MPN, core and memory specifications, package details, application guidance, design notes, and technically constrained replacement candidates. It is intended to help engineers move from part selection to schematic review and PCB implementation while preserving the distinction between confirmed specifications and parameters that require design verification.

Permintaan RFG Kontak
LPC11U68JBD48K - 50MHz Cortex-M0+ MCU | NXP | USB
LPC11U68JBD48K

LPC11U68JBD48K - 50MHz Cortex-M0+ MCU | NXP | USB

The NXP Semiconductors LPC11U68JBD48K is a 32-bit Arm Cortex-M0+ microcontroller operating up to 50 MHz, with 256 KB of flash memory, 36 KB of SRAM, 4 KB of EEPROM, and USB connectivity in a 48-pin LQFP package measuring 7 mm by 7 mm. The device also includes a 12-bit ADC and is specified for an operating temperature range of -40 °C to +105 °C. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one component. The LPC11U68 belongs to NXP's LPC11Uxx family, a low-cost family based on Arm Cortex-M0+ and Cortex-M0 cores. This MCU family targets control and embedded applications that need 32-bit processing, compact code size, low power consumption, and deterministic peripheral operation without the cost and complexity of a higher-performance processor. The LPC11U68JBD48K combines a 50 MHz Cortex-M0+ core with 256 KB of on-chip flash and 36 KB of SRAM. Its 4 KB EEPROM provides nonvolatile storage for parameters, calibration values, or configuration data. USB support makes the device suitable for USB-connected peripherals, while the 12-bit ADC supports analog measurement from sensors, potentiometers, and resistive divider networks. The extended -40 °C to +105 °C temperature range also permits operation across industrial temperature environments. The 48-LQFP package provides a practical option for through-hole assembly and prototype development because its leads are inspectable and accessible on a conventional PCB. Its 7 mm by 7 mm body is larger than the smallest microcontroller packages, but it simplifies hand soldering, signal probing, and rework. Board planners must preserve the manufacturer's land pattern and observe the specified pin, clearance, and soldering requirements. Typical uses include industrial control modules, USB-to-serial or USB-connected data-acquisition equipment, compact sensor interfaces, building-control nodes, and low-cost embedded products. In an analog measurement design, the 12-bit ADC can acquire sensor signals while the Cortex-M0+ core performs filtering, calibration, and data packaging. In a USB peripheral, the integrated USB interface can reduce external connectivity requirements while the MCU manages the application protocol. Design consideration: verify the operating voltage, peripheral pin multiplexing, USB electrical requirements, clock configuration, and programming interface against the manufacturer datasheet before finalizing the PCB. Use the specified decoupling and programming-interface layout, and account for every alternate-function pin used by the application. This page consolidates the manufacturer specifications, commercial inquiry workflow, package information, application guidance, and cross-reference status for LPC11U68JBD48K into one engineering-focused reference.

Permintaan RFG Kontak
LPC11U68JBD64E - 50MHz Cortex-M0+ 256KB MCU | NXP
LPC11U68JBD64E

LPC11U68JBD64E - 50MHz Cortex-M0+ 256KB MCU | NXP

NXP Semiconductors LPC11U68JBD64E is an Arm Cortex-M0+ 32-bit microcontroller operating at up to 50 MHz, with 256 KB of embedded flash memory, in a 64-LQFP 10 mm × 10 mm package. The device belongs to the LPC11Uxx family of scalable, low-cost microcontrollers designed for embedded control, industrial automation, connected equipment, metering, motor control, and low-power IoT designs. A microcontroller is a programmable semiconductor that integrates a CPU, nonvolatile program memory, data memory, peripherals, and communication interfaces on one integrated circuit. The Arm Cortex-M0+ core uses a compact instruction architecture intended to deliver efficient 32-bit processing with lower code-size requirements than many more complex processor architectures. Within the product hierarchy, the LPC11U68JBD64E is an MCU, a microcontroller, and an embedded semiconductor designed for control-oriented embedded systems. The LPC11Uxx family supports CPU frequencies up to 50 MHz and includes flexible, configurable peripherals intended to replace combinations of 8-bit and 16-bit devices. Its 256 KB flash capacity provides room for substantially larger firmware than basic entry-level controllers, while the 64-LQFP package provides 64 accessible peripheral and power pins. The family is also identified by NXP as an Arm Cortex-M0+/M0-based scalable entry-level MCU family. The LPC11U68JBD64E is particularly relevant to designs that need more capability than a simple 8-bit controller but do not require a high-performance Cortex-M3, Cortex-M4, or Cortex-M7 processor. Its combination of 50 MHz operation, 256 KB flash, and 64-LQFP packaging supports compact control boards with mixed analog and digital peripherals. The exact peripheral mix, RAM capacity, voltage limits, and pin functions must be confirmed against the manufacturer datasheet before circuit design. Typical uses include industrial control modules, smart meters, sensor-hub boards, compact motor controllers, building automation equipment, and connected IoT products. In these systems, the MCU can coordinate sensors, apply control logic, supervise actuators, and manage serial communications. Firmware portability can also benefit engineers moving from simpler 8-bit architectures because the Cortex-M0+ platform provides a 32-bit ecosystem while retaining a comparatively simple programming model. PCB planning should account for the exposed dimensions, lead pitch, and pin assignments of the 64-LQFP footprint. Place decoupling capacitors close to supply pins, route sensitive analog signals away from fast digital edges, and confirm every unused pin according to the datasheet. Programming and firmware configuration details should likewise be checked in the NXP product documentation. This product page consolidates the verified manufacturer identity, core frequency, flash capacity, package details, lifecycle information, source links, and application-focused engineering guidance. It also distinguishes exact drop-in alternatives from options that require different packages or firmware qualification, helping designers make a PCB-compatible sourcing decision without overlooking firmware or peripheral differences.

Permintaan RFG Kontak
LPC11U68JBD64K - 50MHz Cortex-M0+ 256KB MCU | NXP
LPC11U68JBD64K

LPC11U68JBD64K - 50MHz Cortex-M0+ 256KB MCU | NXP

NXP Semiconductors LPC11U68JBD64K is an entry-level 32-bit embedded microcontroller based on Arm Cortex-M0+ and Cortex-M0 cores, operating at up to 50 MHz and providing 256 KB of flash memory in a 64-LQFP package measuring 10 mm by 10 mm. The device is positioned as a low-cost migration path from 8-bit and 16-bit microcontroller designs while retaining a 32-bit architecture, a compact instruction set, and flexible configuration. A microcontroller is a semiconductor integrated circuit that combines a processor core, program memory, data memory, and peripherals on one die. In the product hierarchy, the LPC11U68JBD64K is an embedded microcontroller, then a 32-bit microcontroller, and ultimately a general-purpose semiconductor. The Arm Cortex-M0+ architecture is designed for compact embedded-control code, while the presence of Cortex-M0-compatible family information supports simple control-oriented product designs. The principal verified characteristics are a maximum CPU frequency of 50 MHz, 256 KB of flash, a 32-bit CPU, Arm Cortex-M0+/M0 family architecture, and a 64-LQFP surface-mount package. The NXP product page identifies LPC11U68JBD64 as active. This combination makes the LPC11U68JBD64K relevant to embedded control, IoT device, industrial automation, motor-control, metering, and low-power board applications where a compact 32-bit control platform is required. The LPC11Uxx family is intended to replace conventional 8-bit and 16-bit microcontroller implementations with a more capable 32-bit architecture. Its operating frequency of up to 50 MHz provides additional processing headroom for protocol handling, control logic, and state management, while the simple Arm instruction set can reduce software complexity compared with more elaborate embedded processor architectures. Exact RAM, peripheral, voltage, and timing details must be confirmed in the manufacturer datasheet before schematic or firmware design begins. Typical application opportunities include smart metering, connected sensors, compact industrial controllers, motor-control supervisory logic, appliance controls, and low-power IoT nodes. In these systems, the 256 KB flash capacity accommodates a bootloader, application firmware, configuration data, and protocol code. The 10 mm by 10 mm LQFP package also supports conventional surface-mount assembly while providing more exposed perimeter pins than a small leadless package. Designers should use the official NXP data sheet as the controlling source for pin assignment, power requirements, clocking, peripherals, programming, and package dimensions. The LPC11U68JBD64K is supported by the NXP LPC11U00 CMSIS device family package, providing a defined software-device and peripheral baseline for embedded toolchains. This product page consolidates verified manufacturer and distributor information, pricing availability, package details, datasheet links, application context, and design cautions. It also distinguishes confirmed specifications from unavailable data rather than estimating missing electrical or pin-level values, helping engineers make a safer sourcing and design decision.

Permintaan RFG Kontak
LPC1311FHN33 - 72MHz Cortex-M3 MCU, 8KB Flash | NXP
LPC1311FHN33

LPC1311FHN33 - 72MHz Cortex-M3 MCU, 8KB Flash | NXP

The NXP Semiconductors LPC1311FHN33 is an entry-level 32-bit Arm Cortex-M3 microcontroller with up to 72 MHz CPU frequency, up to 8 kB of flash memory, and up to 2 kB of data memory in a 33-pin HVQFN package. Its peripheral complement includes one Fast-mode Plus I2C interface, one UART, and four general-purpose 16-bit timers, making it suitable for cost-sensitive embedded control, communication, and low-power applications. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and I/O in one compact device. The Cortex-M3 architecture provides a 32-bit instruction set and exception-based control architecture, while the LPC1311FHN33 adds embedded peripherals needed for sensors, actuators, data acquisition, and serial communications. In the system hierarchy, it is a microcontroller IC, a semiconductor, and a component within an embedded-control or embedded-processing system. The verified manufacturer result identifies an entry-level Cortex-M3 MCU optimized for integration and low power consumption. Its 72 MHz maximum operating frequency supports responsive control loops and protocol handling, while 8 kB flash and 2 kB data memory suit compact firmware. One Fm+ I2C interface enables connection to sensors and EEPROMs, the UART supports serial data exchange, and four general-purpose timers support timing, pulse generation, and motor-control-related tasks. The LPC1311FHN33 is positioned for applications where integration and compactness matter more than high memory capacity or extensive connectivity. Its small 33-pin HVQFN package is appropriate for dense embedded products, but engineers should verify the exact pin assignments, exposed-pad requirements, decoupling, clocking, and peripheral multiplexing against the manufacturer datasheet before layout or firmware release. Typical uses include industrial sensor nodes, building and access-control terminals, compact instrument controllers, communication modules, low-power embedded systems, and small motor or actuator-control boards. The Cortex-M3 platform can execute interrupt-driven firmware efficiently, while the UART and I2C interfaces reduce the need for separate communication components. Design with the verified 2 V to 3.6 V supply range in mind and confirm device-specific timing and electrical limits in the datasheet. Keep power and decoupling layout compact, provide the required clock and reset behavior, and reserve pins for programming and debug functions. The available search data does not establish a complete pinout, package drawing, or regulator-specific SOA information, so those details must be verified before production use. This page combines the verified NXP product identity, manufacturer specification snippets, distributor references, and the available cross-reference results. Pricing is reported as of 2026-10-23 where a numeric price is not present in the supplied data, and unverified replacement or package claims are explicitly flagged rather than inferred.

Permintaan RFG Kontak
LPC1311FHN33,551 - 72MHz Cortex-M3 8KB Flash MCU | NXP
LPC1311FHN33,551

LPC1311FHN33,551 - 72MHz Cortex-M3 8KB Flash MCU | NXP

The NXP LPC1311FHN33,551 is an entry-level 32-bit Arm Cortex-M3 microcontroller running at up to 72 MHz, with 8 kB on-chip flash memory, up to 2 kB of SRAM, and a 32-pin HVQFN (7x7 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals to control electronic systems. The LPC1311FHN33,551 belongs to the LPC13xx family within the broader hierarchy of 32-bit microcontrollers -> embedded processors -> semiconductors, sitting at the entry level of NXP's Cortex-M3 portfolio. Key features include a 72 MHz Cortex-M3 core with an integrated Nested Vectored Interrupt Controller (NVIC), a Fast-mode plus (Fm+) I2C interface, one UART, four general-purpose timers, up to 28 GPIO pins, and USB device capability available on the wider LPC13xx family. The small 7x7 mm HVQFN-33 package with 0.85 mm height suits space-constrained designs. The Cortex-M3 core uses a 3-stage pipeline with Thumb-2 instruction set, delivering efficient code density and deterministic interrupt handling. Flash memory is tightly coupled for zero-wait-state execution at full speed, and the supply range of 2.0 V to 3.6 V supports battery-powered operation. Operating temperature spans -40C to +85C per the commercial/industrial grade rating. Typical applications include consumer electronics control, HID USB peripherals, industrial sensor nodes, home automation, and simple motor or lighting control where 8 kB of code space and low cost are sufficient. Design consideration: budget code size carefully - 8 kB of flash fills quickly with USB or complex protocol stacks; if more headroom is needed, the pin-compatible LPC1313 (32 kB) in the same HVQFN-33 package is the natural upgrade path. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
LPC1313FBD48/01 - 72MHz Cortex-M3 MCU | NXP | Embedded
LPC1313FBD48/01

LPC1313FBD48/01 - 72MHz Cortex-M3 MCU | NXP | Embedded

The NXP Semiconductors LPC1313FBD48/01 is an Arm Cortex-M3-based 32-bit microcontroller for embedded applications, operating at CPU frequencies up to 72 MHz and integrating up to 32 kB of flash memory with up to 8 kB of data memory. The device is supplied in a 48-pin LQFP package measuring approximately 7 mm by 7 mm. A microcontroller is a programmable system-on-chip that combines a processor core, memory, peripherals, and communication interfaces on one semiconductor device. The LPC1313FBD48/01 belongs to the MCU, embedded processor, and power-management-IC hierarchy. Its Cortex-M3 architecture provides a compact platform for control-oriented products, while its integrated interfaces allow the device to operate without several discrete interface components. Key features include operation at up to 72 MHz, as much as 32 kB of embedded flash, and as much as 8 kB of SRAM. The peripheral set includes one Fast-mode Plus I2C interface, one UART, four general-purpose counter or timer blocks, and as many as 40 I/O ports. The 2 V to 3.6 V operating-voltage range supports low-voltage embedded systems, while the 48-pin LQFP package exposes the mixed-signal and digital resources through a conventional leaded footprint. The LPC1313 family combines a deterministic Arm Cortex-M3 processor core with an integrated peripheral set intended for cost-sensitive embedded control. Flash memory supports in-system firmware storage, and the SRAM provides working memory for control code, interrupt handling, and peripheral data. The I2C and UART interfaces support connection to external sensors, EEPROMs, transceivers, and host controllers. Additional GPIO permits digital inputs, outputs, interrupt sources, and basic control signaling to be consolidated on the same device. Typical applications include industrial sensor nodes, building and access-control equipment, consumer accessories, low-power data collectors, embedded USB peripherals, and compact control boards. A 72 MHz Cortex-M3 can manage multiple interrupt-driven peripherals, protocol handling, and application logic without requiring a higher-complexity processor. For designs requiring several independent timers, sensor interfaces, or communications channels, the integrated resources reduce board area and reduce the number of external devices. The principal design consideration is the 2 V to 3.6 V supply range. The power architecture, regulator design, decoupling, and I/O voltage levels must therefore be coordinated so that every external signal remains within the device's electrical limits. Because the family has a published end-of-life notice, engineers should also confirm the exact orderable suffix, longevity requirements, and migration path before beginning a long-life production design. This product page consolidates the official NXP device description, package and memory characteristics, lifecycle information, interface details, and same-family replacement guidance. It also adds application-oriented selection guidance and practical design notes to help engineers evaluate the LPC1313FBD48/01 beyond basic catalogue information.

Permintaan RFG Kontak
LPC1315FBD48,551 - 72MHz Cortex-M3 MCU 32KB Flash | NXP
LPC1315FBD48,551

LPC1315FBD48,551 - 72MHz Cortex-M3 MCU 32KB Flash | NXP

The NXP LPC1315FBD48,551 is an entry-level 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 32 KB on-chip flash memory and 8 KB SRAM, housed in a 48-pin LQFP (7x7 mm) package. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor built on the ARMv7-M architecture, which uses a 3-stage pipeline and a Harvard bus structure with separate instruction and data buses plus a dedicated peripheral bus. Within the power-management hierarchy, an MCU integrates the CPU core, memory, and peripherals into a single system-on-chip, replacing multi-chip microprocessor solutions in embedded systems. Key features of the LPC1315FBD48,551 include high levels of peripheral integration and low power consumption: a fast GPIO module with pin toggle rates far above legacy 8051-class MCUs, USART serial communication, on-chip ADC, and in-system programmable (ISP) and in-application programming (IAP) flash. The Cortex-M3 core includes an internal prefetch unit supporting speculative branching, plus enhanced debug features via Serial Wire Debug and JTAG interfaces. Architecturally, the LPC13xx series executes Thumb-2 instructions for high code density, and NXP's nested vectored interrupt controller (NVIC) delivers deterministic low-latency interrupt handling essential for real-time firmware. The flash accelerator optimizes sequential code execution at the full 72 MHz clock rate. Typical applications include industrial control and automation nodes, consumer appliances, motor control interfaces, USB-connected accessories, and embedded system retrofit designs where 32-bit performance must replace legacy 8-bit devices without cost or board-area growth. A key design consideration is supply voltage: the LPC1315FBD48,551 operates from a 3.3 V rail, so level shifting is required when interfacing 5 V logic; decouple each VDD pin with 100 nF ceramics placed close to the package. This page synthesizes distributor pricing, drop-in alternatives within the LPC13xx family, and practical design guidance not found in the NXP datasheet alone.

Permintaan RFG Kontak
LPC1316FBD48 - 72MHz Arm Cortex-M3 MCU | NXP | USB
LPC1316FBD48

LPC1316FBD48 - 72MHz Arm Cortex-M3 MCU | NXP | USB

The NXP Semiconductors LPC1316FBD48 is a 32-bit Arm Cortex-M3 microcontroller for embedded applications, operating at up to 72 MHz with 48 KB of flash, 8 KB of SRAM, and USB connectivity in a 48-LQFP 7 x 7 mm package. Its combination of a 72 MHz processor, integrated USB device support, and low-power operation makes it suitable for compact control, communications, and data-acquisition products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. The LPC1316FBD48 belongs to the 32-bit microcontroller hierarchy, using the Arm Cortex-M3 core with enhanced debug support and an integrated support-block architecture. This category provides embedded systems with more processing capability than simple 8-bit controllers while retaining low cost, low power, and deterministic real-time operation. The device provides 48 KB of program flash, 8 KB of SRAM, USB device support, USART, and EEPROM. The 72 MHz Cortex-M3 core supports floating-point instructions and efficient exception handling for responsive control loops. Its integrated USB capability reduces external interface-component requirements in portable data-collection and human-interface devices, while serial communications support links to sensors, modules, and external converters. The LPC1316 family combines a common Arm Cortex-M3 platform with low-power operating characteristics and a high level of peripheral integration. The 48-LQFP package exposes the microcontroller's GPIO, communications, timing, and power-related connections in a conventional surface-mount footprint. Because the target is specified as the LPC1316FBD48 variant, its listed memory configuration is 48 KB flash and 8 KB SRAM rather than the maximum configuration associated with other members of the broader LPC13xx range. Typical uses include USB-connected industrial data loggers, compact sensor interfaces, serial-to-digital gateways, access-control terminals, and embedded control modules. The 72 MHz processing rate is useful for protocol handling and real-time peripheral management, while USB can provide both power and a standard host interface in portable equipment. Designers should preserve the recommended power, clock, decoupling, and programming-interface connections from the manufacturer datasheet. Firmware planning should include adequate flash and SRAM headroom, and USB firmware must account for clocking and bus-power requirements. The LQFP footprint also requires a land pattern designed for its 0.5 mm pitch and a thermal design suitable for the board's ambient environment. This product page organizes the principal LPC1316FBD48 specifications, engineering application guidance, datasheet links, and genuine same-package family alternatives. It also distinguishes exact drop-in candidates from merely similar microcontrollers, helping engineers evaluate board reuse without assuming that compatibility across different cores, peripherals, packages, or memory sizes is automatic.

Permintaan RFG Kontak
LPC1316FHN33,551 - Cortex-M3 72MHz MCU 48KB Flash | NXP
LPC1316FHN33,551

LPC1316FHN33,551 - Cortex-M3 72MHz MCU 48KB Flash | NXP

The NXP LPC1316FHN33,551 is a 32-bit Arm Cortex-M3 entry-level microcontroller operating at up to 72 MHz, with 48 KB of on-chip flash memory and a 32-pin HVQFN (7x7 mm) exposed-pad package. An entry-level 32-bit MCU is an integrated circuit that combines a processor core, program flash, SRAM, and mixed-signal peripherals on a single die, sitting in the product hierarchy between 8-bit MCUs and high-performance Cortex-M4/M7 devices. The LPC1316 belongs to the NXP LPC1300 family, which targets embedded applications requiring a high level of integration and low power consumption. Key features include the Arm Cortex-M3 core with a 3-stage pipeline and Harvard architecture with separate instruction and data buses, CPU speeds up to 72 MHz, 48 KB flash, a USB 2.0 full-speed device controller, USART serial interfaces, and an internal prefetch unit supporting speculative branching for improved execution efficiency. Technically, the Cortex-M3 core integrates an NVIC interrupt controller, SysTick timer, and enhanced debug features, while the LPC1300 peripheral set adds fast GPIO, 10-bit ADC, and serial connectivity on a single 3.3 V supply rail (2.5 V to 3.3 V operating range per distributor data). Typical applications include USB-connected embedded devices, industrial control nodes, consumer appliances, and battery-powered instrumentation where 8-bit MCUs lack headroom but full Cortex-M4 performance is unnecessary. Design consideration: the 32-HVQFN exposed pad must be soldered to a ground plane for both thermal dissipation and signal integrity; verify the 2.5 V to 3.3 V supply window before reusing a 5 V-tolerant design. This page synthesizes verified distributor pricing, pin-compatible LPC13xx family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Permintaan RFG Kontak