Modul RF
Produk (300+)
LSM110A - LoRa & Sigfox 902-928MHz Hybrid Module | SJIT
The Seong Ji (SJIT) LSM110A is a compact, low-power, bidirectional radio transceiver module for the 902 MHz to 928 MHz sub-1 GHz ISM band, integrating Semtech LoRa and Sigfox modulation technologies in a single FCC-certified LCC-34 package measuring 14.0 mm x 15.0 mm x 2.8 mm. The module delivers up to +22 dBm output power and supports Sigfox RC2/RC4 zones together with LoRaWAN on US902-928, AU915-928, and AS923-1 regional profiles, enabling hybrid LPWAN connectivity for global IoT deployments. It is built around an STM32WL series sub-1 GHz SoC, which combines an Arm Cortex-M4 microcontroller with an integrated LoRa radio, eliminating the need for an external MCU in many designs. The module is supplied in both AT-command and API firmware variants, with the API version allowing customer firmware to be integrated directly inside the module. A half-through-hole land pattern allows the LSM110A to be soldered like a standard SMD component onto a simple two-layer carrier board with only a few external passives required. The LSM110A is pre-certified under FCC ID 2BEK7LSM110A, which reduces compliance cost and time-to-market for end products intended for the Americas and Australia. A LoRa (Long Range) radio module is a wireless transceiver sub-system built on Semtech's chirp-spread-spectrum modulation that delivers kilometer-scale communication at very low current consumption, ideal for battery-powered IoT endpoints. Sigfox is a complementary ultra-narrowband LPWAN technology operated by a global network carrier that uses the same sub-1 GHz ISM bands but provides lower bit-rate, longer-range, ultra-low-power messaging. By integrating both protocols, hybrid modules such as the LSM110A let designers choose the optimal transport per packet, geographic region, or application without redesigning hardware. Key features include a high-interference-immunity spread-spectrum physical layer, support for AT and API command interfaces, and FCC pre-certification. The 14.0 x 15.0 mm LCC-34 footprint makes it the smallest LoRa+Sigfox hybrid module in the SJIT portfolio and one of the smallest on the market, allowing product miniaturization for asset trackers and wearable sensor nodes. Architecturally, the STM32WL SoC integrates the radio, modem, and microcontroller into one die, reducing BOM count and PCB area. The LCC-34 package's exposed ground pad improves thermal performance and RF grounding for consistent radiated performance across production lots. Typical applications include Sigfox/LoRaWAN asset tracking, smart agriculture soil and livestock sensors, smart-metering endpoints, industrial SCADA monitoring, and GPS-free indoor/outdoor positioning reference nodes. The hybrid protocol support means a single SKU can ship to the US, Australia, and parts of Asia with no firmware region-locking. When designing with the LSM110A, ensure the antenna matching network is tuned for the specific antenna chosen (chip, trace, or external SMA) and that the host MCU's UART levels match the module's 3.3 V CMOS interface. Power-rail decoupling requires at least a 10 uF bulk plus a 100 nF ceramic placed within 5 mm of the module's VDD pins. This page consolidates distributor pricing, drop-in alternatives from the SJIT LSM family, and practical design notes that are not collated in any single manufacturer datasheet.
LTP5900IPC-WHMA#PBF - SmartMesh WirelessHART Mote 2.4GHz | ADI
The Analog Devices LTP5900IPC-WHMA#PBF is a 22-pin SmartMesh WirelessHART mote module operating in the 2.4 GHz ISM band as part of the Eterna family of IEEE 802.15.4 printed-circuit-board assembly solutions. The module integrates an ARM Cortex-M3 32-bit microprocessor with Dust Networks embedded SmartMesh WirelessHART networking software, an on-board 2.4 GHz radio, and an MMCX antenna connector supporting up to 8 dBm TX power at 250 kbps over 16 channels centered at 2483.5 MHz. The through-hole module is shipped in a tray and is qualified for industrial temperature operation from -40 °C to +85 °C, providing a forward-compatible upgrade path for designers using the legacy M2510 PCB module. A WirelessHART mote is a self-managing, low-power radio node used to build self-forming, self-healing mesh networks for process automation. Within the broader taxonomy, the LTP5900-WHM sits at the intersection of an IEEE 802.15.4 transceiver SoC (system-on-chip), an embedded wireless MCU module, and an industrial-grade sensor-networking appliance. Compared with proprietary RF modules, WirelessHART layers standard IEC 62591 channel hopping and time-synchronized mesh scheduling on top of IEEE 802.15.4e, giving deterministic latency, AES-128 encryption, and full interoperability with any HART host system. Key technical features include 16 selectable 2.4 GHz channels, a transmit output power up to 8 dBm with receiver sensitivity of -95 dBm (typical), an integrated ARM Cortex-M3 core running SmartMesh WirelessHART network stack, secure AES-128 link-layer encryption, and over-the-air firmware upgrade capability. The module carries FCC, IC, ETSI, Telec, and ARIB radio certifications, eliminating the customer's own RF compliance burden for global deployments. Time-synchronized channel hopping provides deterministic latency and sub-millisecond time synchronization across the mesh. Typical applications include wireless process monitoring in petrochemical and oil-and-gas plants, wireless temperature, pressure, and flow sensor nodes, condition monitoring on rotating equipment, environmental monitoring, and any brownfield HART instrumentation installation where running new cable is impractical. The module's ultra-low-power duty-cycled radio and embedded mesh stack allow battery-powered motes to run for years on primary cells. Design considerations when using the LTP5900IPC-WHMA#PBF include providing a regulated 2.1 V to 3.6 V DC supply, routing the MMCX antenna trace correctly, observing the host-board keep-out area under and around the on-board chip antenna path, and following the reference schematic in the manufacturer datasheet. Antenna selection, matching network, and enclosure material strongly influence RF range and must be evaluated against the SmartMesh Power and Performance Estimator tool before final qualification. This page synthesizes distributor pricing for the 22-pin WHM-A variant, drop-in comparison against related SmartMesh modules (LTP5901-WHM with chip antenna, LTP5902-WHM with MMCX connector), and practical design notes for industrial WirelessHART deployment not consolidated in any single distributor listing.
LTP5902IPC-WHMA#PBF - 802.15.4 WirelessHART Mote Module | ADI
The Analog Devices LTP5902IPC-WHMA#PBF is a SmartMesh WirelessHART mote-on-board RF transceiver module in the Eterna family of IEEE 802.15.4 printed circuit board assembly solutions. It operates in the 2.4 GHz ISM band, delivers 8 dBm maximum RF output power, and supports an over-the-air data rate of 250 kbps. The module ships in surface-mount PCB form with an MMCX antenna connector (antenna not included). A wireless mote module is a self-contained sub-system that combines a radio transceiver, microcontroller, and qualified protocol stack on a single PCB so that designers can add mesh networking to a sensor node without writing low-level radio firmware. Within the broader SmartMesh hierarchy, the LTP5902 sits inside Dust Networks' WirelessHART / 6LoWPAN product tree, which itself belongs to the 802.15.4 family of low-rate wireless personal area network (LR-WPAN) standards. SmartMesh WirelessHART networks are self-managing, ultra-low-power mesh networks optimized for industrial process automation. Key features of the LTP5902IPC-WHMA#PBF include transmit current of 5.4 mA to 9.7 mA depending on output power, receive current of 4.5 mA, an integrated ARM Cortex-M3 microprocessor for on-module application processing, and a hardware SPI host interface that exposes network and application services to an external microcontroller. Each mote functions as a full routing node, providing redundant self-healing mesh paths with ultra-low power consumption that enables multi-year battery life on a single cell. The module combines a precision radio with built-in time-synchronized channel hopping, AES-128 encryption, and self-forming/self-healing mesh capabilities that meet the WirelessHART (IEC 62591) standard. This architecture lets industrial operators deploy dense, deterministic sensor networks without manual RF tuning, and it lets battery-powered field instruments operate reliably for years in harsh plant environments. Typical applications include wireless process instrumentation, factory automation sensor networks, condition monitoring of rotating equipment, and battery-powered environmental sensors in oil and gas, pharmaceutical, and chemical plants. The Eterna family's ultra-low power consumption makes it suitable for intrinsically safe installations. When designing with this module, observe the host MCU's SPI timing requirements, provide a clean regulated 3.3 V source with adequate decoupling, and select an MMCX antenna whose VSWR matches the 2.4 GHz band. Verify regulatory certifications for your target region (FCC, IC, ETSI) and follow Dust Networks SmartMesh XT/XD antenna placement guidelines to maximize mesh link margin. This page synthesizes real-time distributor stock, parametric drop-in alternatives, and design notes that are not bundled in the manufacturer datasheet, giving engineers a single reference for selecting the LTP5902IPC-WHMA#PBF in industrial WirelessHART mesh deployments.
MAX-M10S-00B - u-blox M10 GNSS LCC Module | Ultra-Low-Power
The u-blox MAX-M10S-00B is an ultra-low-power, high-performance GNSS receiver module built on the u-blox M10 silicon platform and housed in a 9.7 x 10 mm LCC package with integrated TCXO, LNA, and SAW filter. The module concurrently tracks GPS, GLONASS, Galileo, and BeiDou constellations across the 1.561 GHz, 1.575 GHz, and 1.602 GHz GNSS bands, delivers a tracking sensitivity of -167 dBm and supports an update/data rate of 921.6 kbps on the UART/USB interface. The MAX-M10S-00B ordering code ships with ROM-based SPG 5.10 firmware on a 500-piece reel. What is a GNSS receiver module? A GNSS (Global Navigation Satellite System) receiver module is an integrated electronic assembly that combines the RF front-end (LNA, SAW filter, mixer), baseband correlator, GNSS processor, and a host interface (typically UART, I2C, or SPI) into a single surface-mount component. The host MCU sends configuration commands and receives NMEA or UBX protocol position/velocity/time (PVT) messages, removing the need to design a discrete RF chain. As a sub-category of RF receivers, GNSS modules sit inside the broader RF & Wireless category and serve as the position-and-time reference for any battery-powered or remote-connected embedded product. Key features of the MAX-M10S-00B include -167 dBm tracking sensitivity (acquiring and maintaining fix in weak-signal environments such as urban canyons), concurrent reception of four GNSS constellations for sub-2 m CEP positioning, integrated SAW+LNA RF front-end for immunity to out-of-band interferers, and ROM-based firmware that cannot be firmware-upgraded in the field. The module also supports both 1.8 V and 3.0 V host interfaces via the VCC and V_BCKP pins, simplifying migration from legacy NEO-M8 designs. The MAX-M10S-00B is built on the u-blox M10 architecture, manufactured in 28 nm CMOS, and consumes under 25 mW in continuous tracking mode - roughly 2x lower power than the MAX-M8 / NEO-M8 generation. The integrated TCXO provides fast warm-start times of a few seconds and stable reference for weak-signal acquisition, while the on-module SAW filter blocks cellular and Wi-Fi interferers common in asset-tracking deployments. Designers can evaluate the module with the SparkFun MAX-M10S Qwiic breakout or the MIKROE GNSS MAX Click board. Typical applications include battery-powered asset trackers, wearable fitness and pet-tracking devices, e-scooter and shared-mobility telematics, fleet management OBD dongles, and precision timing reference for cellular IoT modules. Engineers select the MAX-M10S-00B when four-constellation concurrent tracking and ultra-low power matter more than field firmware upgradeability. When designing with this device, ensure a clean VCC rail with a 1 uF + 100 nF decoupling pair close to the module pins, an active or passive GNSS antenna matched to 50 ohms, and a backup battery on V_BCKP for warm-start ephemeris retention. Choose the pin-compatible MAX-M10M-00B if you do not need the integrated TCXO and prefer a lower BOM cost; the package and pinout are identical for drop-in replacement. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - information gain not duplicated on DigiKey, Mouser, or Octopart product pages.
MIFARE DESFire EV3 - AES-128 Contactless Multi-Application IC | NXP
The NXP MIFARE DESFire EV3 (MF3DHx3) is a high-security contactless multi-application IC for smart city services, combining ISO/IEC 14443-4 Type A communication, AES-128 and 3DES cryptographic protection, and EAL5+ Common Criteria certification in a contactless die/package suitable for inlay embedding. It delivers 2-32 KB of EEPROM user memory across the MF3DH23 (2 KB), MF3DH43 (4 KB), MF3DH83 (8 KB) and MF3DHR3 (32 KB variants per family naming) options with configurable ATS, optional RANDOM UID for privacy, and a unique 7-byte serial number per device. A contactless smartcard IC is a passive NFC chip that harvests energy from a reader's RF field, communicates over a 13.56 MHz HF air interface, and stores credentials and application data in secure non-volatile memory. MIFARE DESFire EV3 belongs to the NXP MIFARE DESFire platform family within the broader contactless smart card hierarchy, sitting between classic MIFARE Classic products and secure element SE chips, designed for high-throughput transit fare collection, secure access management, multi-application enterprise credentialing and NFC mobile deployment via MIFARE 2GO. Key features include AES-128 hardware acceleration alongside legacy 3DES support, Secure Dynamic Messaging (SDM) that mirrors secure OTPs as text into the NDEF message (compatible with NTAG DNA readers), SUN (Secure Unique NDEF) message authentication, mutual three-pass authentication per ISO/IEC 7816-4, and full backward compatibility with MIFARE DESFire EV1 and EV2 command sets. The chip is NFC Forum Type 4 Tag certified (Certificate ID 58652) and supports configurable ATS information for card personalization across diverse reader infrastructures. Typical applications include contactless transit ticketing, electronic toll collection, employee and student ID, hotel key cards, citizen eID cards, micropayment loyalty schemes, and mobile credential provisioning via NXP's MIFARE 2GO service. Applications running on DESFire EV3 can be deployed to NFC mobile phones without silicon changes, allowing issuers to manage physical and mobile credentials from a single personalization workflow. When designing with DESFire EV3, ensure the inlay antenna geometry matches the target reader's RF field strength, and verify that the SAM (Secure Access Module) on the reader side supports EV3's full command space including EV2/EV3 transaction MAC commands. Migration from EV1 or EV2 is largely command-compatible but requires re-personalization of application keys. This page synthesizes distributor availability, cross-family alternatives and design trade-offs not found in the manufacturer datasheet.
MJ001-01 - Wi-SUN FAN RF Communication Module | Star Instrument
The Shenzhen Star Instrument MJ001-01 is a Wi-SUN protocol radio frequency communication module integrating an SoC with RF transceiver and Wi-SUN protocol processing, interfacing to host devices via a serial (UART) interface for data and command exchange. It targets smart utility and AMI (Advanced Metering Infrastructure) applications requiring long-range, low-power mesh networking. Wi-SUN (Wireless Smart Utility Network) is an IEEE 802.15.4g-based mesh networking protocol standardized by the Wi-SUN Alliance for utility-scale IoT deployments such as smart meters, street lighting, and distribution automation. Unlike proprietary sub-GHz stacks, Wi-SUN FAN (Field Area Network) provides interoperable, self-healing mesh networks where every node can route traffic, giving utilities carrier-grade reliability and scalability across thousands of endpoints. Key characteristics of the MJ001-01 include its minimal size, low power consumption, and long transmission distance, per the official user manual. The module has passed Wi-SUN Alliance technical standard certification covering FAN PHY (Physical layer) conformance, and carries FCC ID 2A2X4-MJ001-01 for the US market. Star Instrument is recognized by the Wi-SUN Alliance as an early provider of Wi-SUN FAN V1.0 products deployed in overseas pilot and batch applications for automatic meter reading. Architecturally, the module embeds the complete Wi-SUN protocol stack on-chip, offloading RF timing, MAC, and mesh routing from the host MCU. Host integration is simplified to UART command/response traffic, reducing firmware development effort and certification scope for the end device. Typical applications include smart electricity, gas, and water metering, streetlight control networks, and distribution grid monitoring where multi-kilometer mesh links must operate for years on constrained power budgets. A key design consideration is verifying the module pinout, RF regulatory profile (region-specific frequency bands), and serial interface voltage levels against the manufacturer manual before layout, since public parametric data for this part is limited. This page synthesizes verified web sources - the official user manual, Wi-SUN Alliance product listing, and FCC filing - including certification status and sourcing context not consolidated in any single datasheet.
MM6108-MF08651-US - Wi-Fi HaLow 802.11ah Module 902-928MHz | Morse Micro
The Morse Micro MM6108-MF08651-US is a Wi-Fi HaLow RF module compliant with the IEEE 802.11ah sub-1 GHz standard, delivering data rates up to 32.5 Mbps with programmable operation in the 902 MHz to 928 MHz US ISM band. The module integrates an ultra-long-reach power amplifier (PA), a high-linearity low-noise amplifier (LNA), a SAW filter, a T/R switch, and a 32 MHz crystal oscillator on a compact certified module built around the Morse Micro MM6108 SoC. Wi-Fi HaLow is the sub-1 GHz variant of the Wi-Fi standard family (IEEE 802.11ah), designed as a low-power, long-range extension of conventional 2.4/5 GHz Wi-Fi. In the wireless connectivity hierarchy, it sits between short-range Wi-Fi/BLE and licensed-band LPWAN technologies such as LoRaWAN and NB-IoT, offering Wi-Fi-native IP connectivity with kilometer-scale reach and multi-year battery life potential. Key features include data rates up to 32.5 Mbps - roughly an order of magnitude beyond typical LPWAN throughput - long-range link budgets enabled by the ultra-long-reach PA, and low power consumption suited to battery-powered IoT endpoints. The integrated SAW filter and high-linearity LNA provide superior RF performance and out-of-band rejection, while WPA3 security support addresses modern Wi-Fi certification requirements. At the core of the module is the MM6108 single-chip SoC, which integrates the radio, PHY, and MAC functions and supports programmable operation from 850 MHz to 950 MHz at the chip level; the module is tuned and certified for the US 902-928 MHz band. The SoC architecture simplifies Wi-Fi HaLow connection to an external host processor over SDIO/USB-class interfaces, offloading the full 802.11 MAC from the host. Typical applications include smart home automation, industrial control and monitoring, security cameras, access control, and large-scale IoT/M2M sensor networks where conventional Wi-Fi range is insufficient. The Morse Micro MM6108-EKH05 v2 evaluation kit pairs this module with an STM32 MCU for rapid prototyping. Design consideration: because this variant is tuned for the US frequency band, designs targeting EU (863-868 MHz) or other regions must select a region-specific module variant or the chip-level MM6108 with custom RF front-end. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-10-20.
MM610X-001 - Wi-Fi HaLow Sub-GHz IoT Module | AsiaRF
The AsiaRF MM610X-001 is a Wi-Fi HaLow Sub-GHz wireless module based on the Morse Micro MM6108 RF SOC, operating on the IEEE 802.11ah standard below 1 GHz in an LGA-42 stamp-form package with a U.FL connector for an external antenna. Wi-Fi HaLow is a low-power, long-range version of the IEEE 802.11 Wi-Fi standard, defined by the IEEE 802.11ah amendment. As a member of the wireless module family within RF modules and wireless connectivity semiconductors, it offloads the entire RF PHY and MAC from a host processor, exposing a simple digital interface to system designers. Key features include long-range sub-1 GHz connectivity that reaches approximately 10 times the distance and 100 times the area of traditional 2.4 GHz Wi-Fi, low power consumption optimized for battery-powered IoT nodes, and broad regulatory certification. According to Morse Micro, the MM610X-001 carries broader regulatory certification than any other module in the AsiaRF Wi-Fi HaLow range, allowing a single hardware design to ship to more export markets without board respins. The module integrates the MM6108 RF SOC, which implements the full 802.11ah protocol stack. Host connectivity is versatile: the module connects over UART, SDIO, SPI, or I2C, giving designers freedom to match it to low-end MCUs or Linux-class application processors. Community-documented bring-ups include Raspberry Pi 5 integration using Morse Micro MM610x software release packages under mainline Linux kernels. Typical applications include smart city infrastructure, security cameras and surveillance over long distances, industrial sensor networks, agricultural monitoring, and utility metering - scenarios where thousands of devices must connect securely through a single access point over kilometer-scale links. Design consideration: because HaLow operates in sub-GHz spectrum, antenna choice and regulatory region selection (channel plan) directly affect range and throughput; plan the U.FL antenna placement and verify the target market's certified band before production. Note the module requires a host driver stack from Morse Micro - budget integration time for the target OS. This page synthesizes distributor listings, manufacturer datasheets, regulatory information, and drop-in alternative analysis not found on any single source, providing a complete engineering view of the MM610X-001 for sourcing and design decisions.
MM8108-M20 - High-Power Wi-Fi HaLow Module 28.5dBm | Morse Micro
The Morse Micro MM8108-M20 is a high-power IEEE 802.11ah Wi-Fi HaLow transceiver module with up to 28.5 dBm transmit output power and a 902-928 MHz operating band, housed in a compact 18.5 mm x 14 mm surface-mount LGA-style footprint. Wi-Fi HaLow is the sub-1 GHz flavor of Wi-Fi defined by the IEEE 802.11ah standard. Unlike 2.4 GHz and 5 GHz Wi-Fi, HaLow trades bandwidth for range, wall penetration, and power efficiency, making it a wireless protocol positioned between legacy Wi-Fi and LPWAN technologies such as LoRa in the IoT connectivity hierarchy. The MM8108-M20 brings standard IP networking over sub-GHz links, so devices can use native TCP/IP stacks without gateways that translate protocols. Key features include transmit amplification up to 28.5 dBm delivered by an integrated external power amplifier, a surface acoustic wave (SAW) filter tuned to the 902-928 MHz North American band for exceptional receive sensitivity, and host connectivity via USB 2.0 High-Speed, SDIO, or SPI interfaces. The underlying MM8108 second-generation SoC integrates radio, PHY, and MAC functions compliant with IEEE 802.11ah and supports PHY rates up to 43.3 Mbps using 256-QAM modulation at 8 MHz bandwidth. The module is a single-chip solution built around the MM8108 SoC, which Morse Micro states delivers up to 3x more energy efficiency than the next best Wi-Fi SoC, extending battery life in power-sensitive designs. The SAW-filtered RF front end improves out-of-band rejection and receiver blocking performance, which is critical in the crowded sub-GHz license-exempt bands. Typical applications include industrial IoT sensor networks, security cameras and surveillance systems, smart building infrastructure, and long-range access points such as the Gateworks GW16170 M.2 2230 E-Key radio card, which uses the MM8108-M20 with up to +27.5 dBm transmit power in the 902-928 MHz band. Design consideration: the MM8108-M20 is region-specific to the 902-928 MHz band (FCC/IC markets); designs targeting other regulatory domains should evaluate the MM8108-MF15457 module covering 850-950 MHz instead. Antenna matching and thermal layout on the host PCB should follow the Morse Micro hardware design guide. This page synthesizes verified distributor and manufacturer data, drop-in alternative analysis, application guidance, and practical design notes not found in the manufacturer datasheet alone.
MM8108-MF15457 - Wi-Fi HaLow 802.11ah Module, 26dBm | Morse Micro
The Morse Micro MM8108-MF15457 is a fully integrated Wi-Fi HaLow (IEEE 802.11ah) transceiver module operating in the 850 MHz to 950 MHz sub-1 GHz license-exempt RF bands, delivering PHY data rates up to 43.3 Mbps with up to 26 dBm transmit power in a surface-mount RF PAD package. Wi-Fi HaLow is the IEEE 802.11ah amendment of the Wi-Fi standard, purpose-built for long-range, low-power connectivity. Unlike conventional 2.4 GHz or 5 GHz Wi-Fi, HaLow operates below 1 GHz, where propagation characteristics enable roughly ten times greater range and superior wall penetration, making it a key technology in the IoT connectivity hierarchy alongside LoRa, Sigfox, and NB-IoT for smart home, industrial, and infrastructure applications. Key features of the MM8108-MF15457 include compliance with IEEE 802.11ah, PHY rates up to 43.3 Mbps using world-first 256-QAM modulation at 8 MHz bandwidth, up to 26 dBm output power, and FCC, IC, CE, and Telec certifications for multi-region deployment. The module integrates the second-generation MM8108 Wi-Fi HaLow SoC with radio, PHY, and MAC functions on a single chip, together with integrated power amplifiers, drastically reducing external BOM complexity. The underlying MM8108 SoC is a highly integrated, ultra-low-power single-chip connectivity solution that Morse Micro claims delivers up to 3x more energy efficiency than the next best Wi-Fi SoC, and an OFDM transmitter up to 4x more energy-efficient than competing HaLow solutions. This translates directly into longer battery life for power-sensitive IoT endpoints without sacrificing throughput. Typical applications include smart home and security cameras requiring long-range video-capable links, industrial automation and sensor networks, and campus-scale IoT backhaul where a single HaLow access point can serve devices hundreds of meters away. The USB host interface (with SDIO and SPI support depending on loaded firmware) simplifies host integration. Design consideration: place the module per the MM8108-MF15457 Hardware Design Guide, keeping the RF PAD footprint and antenna keep-out areas intact, and confirm regional regulatory band limits (850-950 MHz varies by country) before certification. This page synthesizes distributor availability data, datasheet specifications, certification status, and practical design notes in one place - information not consolidated in the manufacturer datasheet alone.
MMM6000R2 - TRANSAAM TRANS MODULE | NXP / Freescale
The NXP (formerly Freescale Semiconductor) MMM6000R2 is a TRANSAAM transmit module classified as a specialized IC for cellular RF front-end applications. Per the verified product page on DigiKey and distributor descriptions, this part is described as a "TRANSAAM TRANS MODULE" and is associated with NXP/Freescale's legacy cellular RF power-management portfolio. The MMM6000R2 is sold primarily through authorized distributors including Rochester Electronics (the authorized afterlife source for NXP/Freescale legacy parts), LCSC, and several independent distributors; one marketplace listing (kstmicro.com) reports an inventory of 36,000 units, indicating healthy aftermarket availability despite an older product generation. What is a TRANSAAM module? In legacy cellular RF design, a TRANSAAM (transmit antenna amplifier module) is a specialized RF integrated circuit that integrates transmit signal-chain functions for 2G/3G/EDGE handset front-ends, often alongside the associated power-management biasing. TRANSAAM modules sit at the interface of the baseband transceiver and the power amplifier, providing controlled gain, ramping, and bias for the transmit path. Within the system hierarchy, a TRANSAAM belongs to: specialized IC -> RF front-end IC -> wireless transceiver subsystem -> cellular handset platform. Key features documented in the verified data include the long-standing NXP/Freescale RF integrated-circuit pedigree and the dual NXP / Freescale branding carried through from the Freescale acquisition by NXP Semiconductors. The part is listed as RoHS compliant per the kstmicro product page. Because the original datasheet (referenced as a 16-page PDF on alldatasheet for the related MMM6025 family) is no longer hosted on the NXP corporate site, this page synthesizes distributor catalog information and the related MMM60xx family datasheet to characterize the part. Modern equivalent parts from NXP's Airfast and RF GaN portfolios are recommended for new designs, with the MMM6000R2 used for maintenance of legacy EDGE/WCDMA platforms. Typical applications include EDGE/WCDMA handset transmit modules, legacy cellular infrastructure transmit chains, RF power-amplifier bias controllers, and repair/maintenance of older 2G/3G mobile platforms. The part is also encountered as a replacement component for OEM service stocks and as a long-term-supply (LTS) part via Rochester Electronics. Modern 4G LTE and 5G NR designs should migrate to NXP's Airfast MMIC portfolio or equivalent GaN/SiGe PAs. Design considerations for this part include verifying the exact RF frequency band coverage against your baseband transceiver before substitution, confirming the supply-voltage rail (the related MMM6025 family operates in the 3.0-4.5 V range), and budgeting for legacy-IC long lead times since authorized stock is increasingly limited to Rochester Electronics and independent distributors. Where possible, perform a substitution-validation bench test with the original baseband chipset to confirm transmit EVM, ACLR, and ramp-profile compliance. This page synthesizes distributor pricing, stock data, drop-in cross-reference options, and design notes not consolidated in the original manufacturer datasheet, providing an integrated engineering view that single distributor listings do not offer.
MSN3420-CB2FO - 48x25GbE 12x100GbE Spectrum-2 Switch | NVIDIA
The NVIDIA Mellanox MSN3420-CB2FO is a 1U rack-mountable Open Ethernet switch based on the Spectrum-2 (SN3000 series) ASIC, delivering 48 x 25GbE SFP28 ports and 12 x 100GbE QSFP28 ports with up to 4.8 Tbps of switching capacity, dual AC power supplies, port-to-cloud (P2C) airflow, and an ONIE boot loader for open network operating system installation. A data center Ethernet switch is a network device that forwards Layer-2 and Layer-3 traffic between servers, storage systems, and upstream networks. In the network hierarchy, a top-of-rack (ToR) switch like this one sits at the access layer, aggregating server connections and uplinking to leaf and spine switches in a fabric topology. Switches are classified as networking hardware rather than semiconductors, though the Spectrum-2 ASIC at their core performs packet processing in silicon. Key features include wire-speed Layer-2 and Layer-3 forwarding for cloud-scale fabrics, port speeds spanning 1GbE to 100GbE on a single platform, Inband Network Telemetry (INT)-ready hardware, streaming telemetry support, and 512K on-chip flow counters for deep observability. The x86 onboard CPU allows full-featured network operating systems such as NVIDIA Onyx or Cumulus Linux via ONIE. The Spectrum-2 ASIC is the second generation of NVIDIA's Spectrum switching silicon, purpose-built for leaf, spine, and super-spine data center applications with consistent low latency at full line rate. Typical applications include top-of-rack server access for clouds migrating from 10G to 25G, leaf-spine fabric builds with 100GbE uplinks, and high-performance computing interconnects. When deploying, confirm airflow direction (P2C on this SKU, C2P on the -CB2FC variant) matches rack cooling before ordering. This page synthesizes distributor listings, sibling SKU comparisons, and deployment guidance not found in a single manufacturer document. Pricing data was not available in verified sources as of 2026-10-19; request a quote.
MSN3420-CB2RO - 48x25GbE 12x100GbE Spectrum-2 Switch | NVIDIA
The NVIDIA (Mellanox) MSN3420-CB2RO is a Spectrum-2 based 1U Open Ethernet switch delivering 48x SFP28 25GbE ports plus 12x QSFP28 100GbE ports, with 4.8 Tbps non-blocking switching capacity, ONIE bootloader (no NOS pre-installed), 2x AC PSU, and C2P (connector-to-panel) airflow. An Open Ethernet switch is a network switch sold without a pre-loaded network operating system. The ONIE (Open Network Install Environment) bootloader lets the operator install any compatible NOS, such as Cumulus Linux, SONiC, or Onyx. In the data center hierarchy, these platforms serve as leaf or top-of-rack (ToR) switches within leaf-spine architectures built on merchant silicon switching ASICs. Key features include the Spectrum-2 ASIC providing line-rate Layer 2/Layer 3 forwarding with consistent low latency, 48-port 25G SFP28 density with 12x 100G QSFP28 uplinks, redundant hot-swappable 2x AC power supplies, front-to-back C2P airflow for hot-aisle exhaust, and a 1U rack-mount chassis. The platform supports port speeds from 1GbE to 100GbE depending on optics. The Spectrum-2 family is purpose-built for cloud-scale leaf/spine/super-spine data center networks, supporting advanced software-defined networking features. NVIDIA documentation describes the SN3000 series as delivering high performance, consistent low latency, and web-scale reliability for cloud, hyperconverged storage, and data analytics applications. Typical deployments include top-of-rack server connectivity in hyperscale and enterprise data centers, leaf-layer aggregation in leaf-spine fabrics, storage network fabrics, and Open Networking white-box projects where NOS choice flexibility is required. Design consideration: because the RO suffix indicates ONIE-only with no pre-installed NOS, plan NOS licensing and installation before deployment; also verify airflow direction (C2P) matches rack cooling layout. This page synthesizes distributor availability, sibling-SKU alternatives, and deployment guidance not found together on manufacturer or distributor pages.
MSN3700-CS2FO - 32x QSFP28 100GbE 1U Switch | NVIDIA Mellanox
The NVIDIA Mellanox MSN3700-CS2FO is a Spectrum-2 based 100GbE Open Ethernet switch system in a compact 1U rack form factor, featuring 32 QSFP28 ports delivering 6.4 Tbps of switching capacity, an x86 CPU, dual AC power supplies, ONIE boot loader, and P2C (port-to-cloud) airflow in a standard-depth chassis. A data center leaf/spine switch is a network device that aggregates traffic from top-of-rack leaf switches and routes it between spine layers in cloud-scale layer-2 and layer-3 networks. The MSN3700-CS2FO belongs to the NVIDIA Spectrum SN3000 switch family, which sits within the broader hierarchy of Ethernet switching systems -> Open Ethernet bare-metal switches -> data center aggregation/spine platforms. Key features include 32 QSFP28 ports each supporting up to 100GbE (with breakout to 4x25GbE per port typical for the SN3700C class), a forwarding rate of 8.33 Bpps, and low latency of approximately 425 ns according to distributor specifications. The Spectrum-2 ASIC provides consistent low latency and advanced software-defined networking features, making the platform suited to web-scale IT, cloud, hyperconverged storage, and data analytics workloads. Technically, the switch is delivered as a bare-metal Open Ethernet platform with an ONIE (Open Network Install Environment) boot loader, allowing operators to install a NOS of their choice such as Cumulus Linux, SONiC, or other ONIE-compatible operating systems. The x86 management CPU enables local NOS execution, while dual redundant AC power supplies and front-to-back P2C airflow support hot-aisle/cold-aisle data center deployments. A rail kit is included for standard 19-inch racks. Typical applications include 100G spine and leaf-spine aggregation in cloud data centers, high-density 25G server connectivity via port breakouts, hyperconverged storage fabrics, and big data analytics clusters where low-latency, high-throughput east-west traffic is critical. A key design consideration: this OPN is listed by NVIDIA as End of Life (EOL) and no longer orderable through normal channels, so new deployments should evaluate current Spectrum platforms or refurbish/secondary-market stock with warranty coverage. This page synthesizes distributor listings, the NVIDIA SN3000 series datasheet, hardware user manual ordering information, and drop-in alternative analysis not found on any single manufacturer page.
MSN3700-CS2RO - 32x100GbE QSFP28 Spectrum-2 Switch | NVIDIA
The NVIDIA (Mellanox) MSN3700-CS2RO is a Spectrum-2 based 1U Open Ethernet switch with 32 QSFP28 ports supporting up to 100Gb/s per port, a total switching capacity of 12.8 Tb/s (full duplex), and forwarding rates of up to 8.33 billion packets per second (Bpps). It ships as a bare-metal ONIE-enabled system with an x86 CPU and dual AC power supplies. A data center Ethernet switch is a network device that forwards Layer 2 and Layer 3 frames and packets between servers, storage systems, and upstream networks. Within the networking hierarchy, the switch sits above the physical cabling layer and below the routing overlay, forming the leaf and spine fabric of modern cloud and enterprise data centers. Open Ethernet switches such as this one ship without a pre-installed network operating system, allowing installation of SONiC, Cumulus Linux, or another NOS through the ONIE boot loader. Key features include the Spectrum-2 ASIC (second-generation Spectrum family), 32 QSFP28 ports spanning speeds from 1GbE to 100GbE, L3 managed operation, and connector-to-power (C2P) airflow for hot-aisle exhaust compatibility. The dual redundant AC power supplies accept 100-264 V AC input, and the standard-depth 1U chassis is rack-mountable with the included rail kit. The Spectrum-2 architecture is purpose-built for leaf, spine, and super-spine topologies, providing ultra-low latency and high pipe efficiency for east-west traffic. Port speeds from 1GbE to 400GbE across the SN3000 series allow full-rack server connectivity at any speed with a single platform family. Typical applications include cloud data center leaf-spine fabrics, enterprise core networks, high-performance computing interconnects, and storage area network fabrics requiring predictable 100GbE throughput. Design consideration: verify airflow direction and PSU type before ordering, since the SN3000 family uses airflow and power suffixes (CS2RO = C2P airflow, 2x AC) that are not field-interchangeable in some deployments. This page synthesizes distributor availability, same-family drop-in system alternatives, and practical deployment notes not found in the NVIDIA datasheet.
MSN3700-VS2FO - 32x200GbE Spectrum-2 1U Switch | NVIDIA
The NVIDIA MSN3700-VS2FO (SN3700 series) is a Spectrum-2 based 1U Open Ethernet switch delivering 32 x QSFP56 ports at 200GbE, 12.8 Tb/s switching capacity, and 8.33 Bpps forwarding rate with just 425 ns latency. A fixed-configuration data center switch is a complete networking system that aggregates and routes high-speed Ethernet traffic between server racks and the network spine. Within the hierarchy of data center fabric equipment, it occupies the leaf/spine/super-spine tier above top-of-rack (ToR) access switches, providing the high-port-count, low-latency backbone that modern cloud and AI clusters require. Key features include 32 QSFP56 ports supporting speeds from 10GbE to 200GbE per port, the 2nd-generation NVIDIA Spectrum-2 ASIC purpose-built for leaf/spine/super-spine topologies, and an ONIE boot loader enabling installation of open network operating systems such as Cumulus Linux. The unit ships with two hot-swappable AC power supplies, an x86 management CPU, standard-depth chassis, power-to-connector (P2C) airflow, and a rail kit. Technically, the Spectrum-2 silicon provides a shared-memory, cut-through forwarding architecture that achieves consistent sub-microsecond latency regardless of port mix, making it well suited to east-west traffic patterns in machine learning and high-performance computing fabrics. Each port can operate independently at 10/25/40/50/100/200GbE, allowing a single chassis to serve mixed-speed uplinks and downlinks without oversubscription hardware changes. Typical applications include 200G spine/super-spine switching in cloud data centers, AI training cluster back-end fabrics, and high-density storage area network aggregation. The 12.8 Tb/s non-blocking capacity supports full-rack GPU node connectivity at line rate. Design consideration: airflow direction is fixed at order time (P2C on this SKU); verify rack cooling direction before deployment, and confirm the 0 to 40 C operating envelope against your facility conditions. This page synthesizes distributor availability, same-platform drop-in variant comparisons, and practical deployment notes not found in the manufacturer datasheet.
MSN3700-VS2RC - 200GbE 32xQSFP56 Spectrum-2 Switch | NVIDIA
The NVIDIA (Mellanox) MSN3700-VS2RC is a Spectrum SN3700 series 1U Open Ethernet switch delivering 32 QSFP56 ports of 200GbE connectivity with 12.8 Tb/s aggregate throughput and 8.33 Bpps packet processing capacity, housed in a standard-depth 1U rack-mount chassis with two AC power supplies and C2P (connector-to-panel) airflow. A data center Ethernet switch is a networking device that forwards Ethernet frames between endpoints at Layer 2 and Layer 3, forming the leaf, spine, and super-spine tiers of modern data center fabric topologies. Within the power/performance hierarchy of networking equipment, the switch platform sits above NICs and below full routing platforms, and the SN3700 belongs to the third generation of NVIDIA Mellanox Spectrum switch systems purpose-built for leaf/spine/super-spine roles. Key features include the Spectrum-2 ASIC (2nd generation), port speeds spanning 1GbE to 400GbE, full 32-port 200GbE density in a single rack unit, and an onboard x86 CPU for hosting the pre-installed Cumulus Linux network operating system. This Open Ethernet design frees operators from vendor-locked NOS choices, supporting SONiC and other open network operating systems alongside Cumulus Linux. The Spectrum-2 architecture provides deep port buffers, virtualization-friendly features, and scale-out fabric capability that enables full rack connectivity to any server at any speed. Rich network virtualization support makes the platform suitable for large enterprises and cloud data centers consolidating multiple overlay networks on shared physical infrastructure. Typical applications include 200GbE spine and super-spine tiers in hyperscale and cloud fabrics, high-density leaf deployments aggregating 100G server connections, and high-performance computing (HPC) interconnects where the 8.33 Bpps processing rate sustains lossless traffic at line rate. Design consideration: verify rack power (2x AC PSUs) and front-to-back C2P airflow direction against cold-aisle/hot-aisle layout before ordering, since airflow direction is fixed per SKU. For Cumulus Linux deployments, confirm NOS licensing and QSFP56 breakout cable compatibility (2x100G, 4x50G) for mixed-speed fabrics. This page synthesizes distributor pricing, family-variant comparisons, and practical deployment notes not found together in the manufacturer datasheet.
MSN3700-VS2RO - 200GbE 32x QSFP56 Spectrum-2 Switch | NVIDIA
The NVIDIA Mellanox MSN3700-VS2RO is a 200GbE Open Ethernet switch based on the Spectrum-2 ASIC, delivering 12.8 Tbps of switching capacity through 32 QSFP56 ports in a 1U rack-mount chassis with standard depth, connector-to-power (C2P) airflow, dual AC power supplies, an x86 CPU, and an ONIE boot loader. A data center Ethernet switch is a managed networking device that aggregates and routes traffic between servers at the leaf, spine, or super-spine layer of a fabric hierarchy. Within the broader networking hierarchy, the MSN3700-VS2RO sits in the top-of-rack or end-of-row switch category, which in turn belongs to the Ethernet switch family of network switching equipment. Open Ethernet switches such as this one ship with ONIE, allowing installation of a choice of network operating systems rather than a locked-in vendor OS. Key features include 32 QSFP56 ports supporting speeds from 1GbE up to 200GbE per port, 12.8 Tbps non-blocking capacity, redundant hot-swappable 2x AC power supplies, and connector-to-power airflow for predictable thermal management in data center hot/cold aisle layouts. The integrated x86 management CPU enables full-featured NOS deployment including NVIDIA Onyx or Cumulus Linux. Technically, the Spectrum-2 generation ASIC provides deep buffering and flexible port bifurcation (for example, a 200G port split into 2x100G or 4x50G), enabling mixed-speed rack connectivity. Port speeds span 1GbE to 400GbE across the SN3000 series platform family, giving fabric designers flexibility in leaf/spine blocking ratios. Typical applications include high-density 100G/200G leaf-spine data center fabrics, super-spine aggregation layers, cloud and enterprise top-of-rack aggregation, and storage network backends where 200GbE uplinks reduce oversubscription. When deploying, verify rack airflow direction compatibility (C2P versus P2C variants exist in the same family) and confirm AC power feed redundancy before installation. This page synthesizes distributor pricing, drop-in SKU alternatives, and practical deployment notes not found in the manufacturer datasheet.
NEO-M8T-0 - Concurrent GNSS Timing Module, -167dBm | u-blox
The u-blox NEO-M8T-0 is a concurrent GNSS timing receiver module built on the u-blox M8 platform, supplied in a compact 12.0 x 16.0 mm LCC surface-mount form factor. It supports simultaneous reception of four global navigation satellite systems - GPS, GLONASS, Galileo, and BeiDou - plus QZSS, and provides tracking sensitivity down to -167 dBm together with an industry-leading acquisition sensitivity of -148 dBm for cold starts. What is a GNSS timing module? A GNSS (Global Navigation Satellite System) timing module is a satellite-receiver subsystem that derives precise frequency, phase, and time-of-day information from atomic-clock references aboard navigation satellites. Within the broader power-and-clock hierarchy a timing module sits alongside oscillators, RTCs, and TCXOs as the highest-accuracy time reference, sitting above standalone oscillators in stability and below PTP/NTP grandmasters in protocol richness. The timing-module category is engineered for applications where nanosecond-level pulse alignment, deterministic 1 PPS output, or raw pseudorange observables are required. The NEO-M8T-0 delivers two key timing features that distinguish it from navigation-grade modules: a configurable timepulse (1 PPS) output with sub-25 ns jitter and a survey-in mode that disciplines the internal oscillator against GNSS-derived timing, allowing the receiver to act as a stable, disciplined clock source even when fewer than four satellites are visible. The module also provides raw carrier-phase and pseudorange data over UART, USB, SPI, and I2C (DDC) for use in research, geodesy, and timing-instrumentation applications. Power consumption is optimized for low-duty-cycle timing deployments. Typical applications include cellular base-station synchronization (e.g., 4G/LTE and 5G NR networks requiring holdover), broadcast audio and DVB-T transmitters, power-grid PMU phasor measurement units, financial timestamping servers for MiFID II compliance, and scientific instruments such as radio telescopes and particle-physics experiments. The wide operating temperature range of -40C to +85C and the standard NEO form factor (pin-compatible with NEO-M8N and other u-blox M8 modules) allow ready migration from earlier u-blox generations. When designing with this part, provide a stable primary supply between 2.7V and 3.6V, an active antenna with at least 15 dB of gain, and route the timepulse and serial lines away from switching converters. Note that the -167 dBm tracking figure gives 6 dB of margin over navigation-only modules, which is critical for timing applications where partial satellite visibility is common. This page synthesizes distributor stock, drop-in alternatives including the LEA-M8T and ZED-F9T, and practical design notes that complement the manufacturer datasheet.
NINA-B112-04B-00 - BLE 5.0 Module, nRF52832 | u-blox
The u-blox NINA-B112-04B-00 is a stand-alone Bluetooth 5.0 low energy (BLE) transceiver module operating in the 2.4 GHz band, built on the Nordic Semiconductor nRF52832 SoC with an integrated chip antenna, delivered in a compact surface-mount NINA-B1 form factor. A Bluetooth low energy module is a complete radio subsystem that integrates the RF transceiver, microcontroller, antenna, and certified RF matching network into a single drop-in component. Within the connectivity hierarchy, it sits below full networking gateways but above bare SoCs: engineers gain a fully certified, pre-tested radio without designing a 2.4 GHz RF section, greatly reducing certification cost and time to market. Key features of the NINA-B112-04B-00 include Bluetooth v5.0 compliance with 2 Mbps PHY support, 512 kB flash memory and 64 kB RAM for application code and data, and an internal metal-optimized PIFA chip antenna providing a range of more than 300 m independent of ground plane and component placement, according to the NINA-B1 datasheet (UBX-15019243). The module supports Bluetooth mesh and up to 20 simultaneous Bluetooth connections. Technically, the module is powered by the nRF52832, whose Cortex-M4F processor executes either the pre-flashed u-blox u-connectXpress firmware (AT-command driven) or, in the open-CPU NINA-B1 variants, customer application code directly. The NINA-B112-04B carries u-connectXpress software; the -00B variant ships with open CPU firmware for native development. Typical applications include industrial sensor nodes, smart-home and IoT edge devices, asset trackers, and battery-powered medical wearables, where its low-power BLE profile and worldwide radio certifications shorten design cycles. A key design consideration is antenna keep-out: although the internal PIFA is ground-plane independent, the system integration manual requires a defined clearance area around the module to preserve the 300 m-plus range performance. This page synthesizes distributor pricing, pin-compatible NINA-B1 family alternatives, and practical design notes not found in the manufacturer datasheet.
NRF9160-SICA-B1A-R7 LTE-M/NB-IoT GPS SiP Module
Nordic Semiconductor NRF9160-SICA-B1A-R7 is a low-power cellular IoT System-in-Package combining an Arm Cortex-M33 processor, LTE-M/NB-IoT modem, RF front end, GPS support, 1 MB Flash, and 256 KB RAM in a 127-PowerTFLGA module. The integrated modem supports 3GPP LTE Release 13 Cat-M1 and Cat-NB1 and 3GPP LTE Release 14 Cat-NB1 and Cat-NB2, while the RF section covers approximately 700 MHz to 2.2 GHz. The nRF9160 is a highly integrated cellular IoT module rather than a conventional discrete transceiver. Its processor, modem, radio front end, security features, memory, and power-management functions are combined in one package, simplifying cellular product development. The module is designed for low-power single-device designs and supports cellular connectivity alongside integrated location tracking. Key features include an Arm Cortex-M33 application processor, advanced hardware security, integrated GPS, 1 MB of Flash memory, 256 KB of RAM, and a complete cellular modem. The architecture allows embedded firmware, networking, application processing, and radio connectivity to be handled in a compact module rather than across several discrete components. The nRF9160 supports both LTE-M and NB-IoT, including LTE Release 13 and Release 14 categories listed in the manufacturer material. This broad standards support is useful for products that must operate across different cellular deployments. The integrated RF front end and modem reduce the amount of external RF integration required compared with a discrete cellular design. Typical applications include cellular IoT sensors, asset trackers, smart meters, industrial monitoring equipment, connected logistics devices, and GPS-enabled remote telemetry products. The integrated GPS capability is particularly useful when an application needs location data without adding a separate GPS receiver. Designers should preserve the module’s recommended power, decoupling, antenna, and RF layout practices. Cellular designs are sensitive to grounding, antenna routing, transmission power, regulatory requirements, and power-supply stability. Review the manufacturer product specification and ordering information before finalizing PCB layout or changing the hardware revision. This page synthesizes the verified distributor descriptions, manufacturer datasheet references, packaging information, application guidance, and drop-in cross-reference evidence for NRF9160-SICA-B1A-R7. Pricing, detailed electrical limits, pin-level data, and certification status must be confirmed against the latest manufacturer documentation and distributor records.
NTAG213 - NFC Forum Type 2 Tag, 144B User Memory | NXP
The NXP Semiconductors NTAG213 is a NFC Forum Type 2 Tag compliant contactless IC that operates at 13.56 MHz and exposes 144 bytes of user-accessible memory. It is fully compliant with NFC Forum Type 2 Tag and ISO/IEC 14443 Type A specifications, and is housed in standard wafer-level packages (e.g., SOT-23-equivalent die or bare-die formats used on inlays and tags). As an NFC Type 2 tag, the NTAG213 belongs to the broader family of passive contactless memory tags that harvest operating energy from the RF field of an NFC reader or smartphone. The NTAG21x family (NTAG213/215/216) is NXP's mainstream product line for NFC tags; within that family, NTAG213 is the lowest-memory variant. Type 2 Tags sit below NFC Type 4 Tags (ISO/IEC 14443-4 compliant) in the NFC Forum tag hierarchy and are optimized for simple, low-cost, high-volume tap-and-read use cases rather than secure transactions. Key features of the NTAG213 include a 7-byte unique identifier (UID), a 32-bit password-based protection mechanism with password attempt counter, a 24-bit one-way programmable (OTP) memory area, an ECC-based originality signature for anti-cloning support, a built-in NFC counter (NTAG213 also exposes the ASCII mirror and UID ASCII mirror pages), and a true anti-collision loop that allows multiple tags to be inventoried in the field simultaneously. Read range is typically up to 10 cm depending on antenna geometry. Technically, the NTAG213 implements a half-duplex, 106 kbit/s data rate over ISO/IEC 14443 Type A modulation. The internal memory is organized into user memory (144 bytes) plus configuration pages, with write endurance rated for 100,000 cycles per page and data retention of 10 years per the NXP datasheet. The IC operates without any external power source: the analog front end and on-chip rectifier derive all operating current from the reader's RF field. Typical applications include smart out-of-home and print media advertising, Bluetooth pairing / Wi-Fi hand-off companion tags (NFC Forum NDEF handover), product authentication labels via the originality signature, NFC shelf labels in retail, business card / SoLoMo tap-to-action tags, and game figure integration (NTAG213 is used in many Bluetooth-paired toys and is one of the memory options for NFC Forum NDEF-based consumer uses). When designing with NTAG213, observe the antenna matching guidance in the NXP application notes: a recommended etched or printed coil antenna of roughly 35 mm x 35 mm to 45 mm x 45 mm delivers the typical 5-10 cm read range on a mobile phone reader, and a tuning capacitor in the 15-25 pF range compensates the loop inductance. Keep sufficient clear space around the antenna, and avoid placing the tag directly on metal surfaces without a ferrite shield. This page consolidates distributor pricing, drop-in alternatives, and practical antenna/design notes not assembled in the manufacturer datasheet alone.
NTAG215 - 504B NFC Type 2 Tag IC, ISO/IEC 14443A | NXP
The NXP Semiconductors NTAG215 is an NFC Forum Type 2 Tag compliant IC with 504 bytes of usable user memory (126 pages of 4 bytes), 7-byte UID, and a 32-bit one-way counter, fully compliant to ISO/IEC 14443 Type A. It operates at 13.56 MHz and is delivered in wafer-level packages including the standard NTAG215 die form used inside contactless smart cards, tags, and labels. An NFC (Near Field Communication) tag IC is a passive, contactless memory device that harvests operating energy from the RF field of an NFC reader and exposes its stored data over the air using a standardized protocol. NFC Forum Type 2 Tags are based on ISO/IEC 14443 Type A and are the most widely supported tag type in consumer NFC devices (smartphones, tablets). In the broader hierarchy, the NTAG215 belongs to the family of contactless memory ICs -> RFID transponders -> NFC/RFID semiconductors -> wireless connectivity ICs. Its Type 2 compliance guarantees interoperability with virtually every modern NFC reader. Key features include 504 bytes of user-accessible EEPROM organized as 126 pages, a factory-programmed 7-byte unique identifier (UID), a 32-bit one-way counter for tamper detection or tap counting, NFC Forum Type 2 Tag and ISO/IEC 14443 Type A compliance, 106 kbps data rate, and built-in password protection with full memory read/write protection. Typical read range is up to 10 cm depending on antenna geometry, and operating temperature spans -25C to +70C for consumer variants. The NTAG215 is the middle-memory sibling in the NTAG21x family, positioned between the smaller NTAG213 (144 bytes) and the larger NTAG216 (888 bytes). All three share the same command set, UID length, counter, and password feature, making them software-compatible. The NTAG215's 504-byte capacity was chosen by NXP and Nintendo to exactly accommodate Amiibo figures, which is why the part is the de facto standard for NFC gaming collectibles and many consumer IoT pairing tags. Typical applications include Nintendo Amiibo figures, gaming collectibles, product authentication and anti-counterfeit labels, Bluetooth/Wi-Fi pairing NFC tags, smart posters and out-of-home advertising, vCard/business card sharing, mobile companion tags, and inventory/asset tracking where medium-capacity Type 2 memory is sufficient. When designing with the NTAG215, ensure the antenna is matched to 13.56 MHz and the contactless coupling area supports ISO/IEC 14443 Type A communication. The password feature must be enabled by writing the relevant configuration pages; failure to lock memory leaves the tag open to unauthorized rewrite. For Amiibo compatibility, use only NTAG215 (not NTAG216 or NTAG213) at the exact page count, since Amiibo NDEF payloads are sized for 504 bytes. This page synthesizes cross-distributor pricing, drop-in and same-family alternatives, and practical design notes for embedding NTAG215 into cards, tags, and labels not found in the bare manufacturer datasheet.
OM-O2P - Omega2+ WiFi IoT Module, 2.4GHz, 580MHz | Onion
The Onion Corporation OM-O2P is the Omega2+ System-On-Module (SOM), a compact Linux-based IoT computer integrating a 580 MHz MIPS 24KEc SoC, 128 MB DDR2 memory, 32 MB on-board flash, and a 2.4 GHz 802.11 b/g/n WiFi transceiver in a through-hole module form factor designed for breadboard and docking-station prototyping. What is a System-On-Module? A System-On-Module (SOM) is a small, self-contained computing module that integrates a microprocessor, memory, wireless radios, and power management onto a single PCB, exposing interfaces through pin headers. SOMs sit in the hierarchy between a microcontroller (no OS, single-purpose) and a single-board computer (full I/O on one board). The Omega2+ family targets the IoT edge node category, offering Linux programmability in a footprint smaller than a credit card, suitable for connected-device prototyping. Key features include 802.11 b/g/n WiFi with on-board PCB antenna, hardware cryptographic support, hardware-accelerated microSD slot accepting SDXC cards up to 2 TB at up to 300 MB/s, and 15 GPIO pins for peripheral integration. The OM-O2P draws approximately 260 mA at 3.3 V under typical WiFi-active load, supports firmware updates over the air (FOTA), and exposes USB 2.0, I2C, I2S, SPI, and UART interfaces through the 2x15 2.54 mm pin header. Technically, the OM-O2P is built around the MediaTek MT7688AN MIPS-based WiFi SoC, which combines a 580 MHz MIPS 24KEc CPU core with an integrated 802.11n MAC/baseband/radio. This single-chip architecture keeps the BOM compact and BOM cost low while providing enough compute for lightweight Linux tasks, MQTT clients, and on-device scripting. The 128 MB DDR2 RAM is double what the smaller Omega2 (OM-O2) ships with, allowing larger application workloads. Typical applications include home automation gateways, WiFi-connected sensor nodes, IP-camera prototypes, smart agriculture controllers, and educational Linux-on-SoC platforms. Designers frequently dock the OM-O2P onto the Onion Expansion Dock (OP-EA) or the Arduino-compatible Power Dock (OP-PA) to access Arduino-shield expansion. When designing with this module, verify that your 3.3 V regulator can supply at least 500 mA peak for WiFi TX bursts, and place a local 10 uF decoupling capacitor near the VIN pin. The through-hole header footprint makes the module hand-solderable and breadboard-friendly without requiring reflow equipment. This page synthesizes distributor pricing, real drop-in alternatives within the Omega2 family, and practical docking-station design notes not found in the manufacturer datasheet alone.