AD625BDZ - Programmable Gain Instrumentation Amplifier | Analog Devices
MPN: AD625BDZ ✗ Akhir HidupAD625BDZ Ringkasan
An instrumentation amplifier is a differential-input analog IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. Within the broader hierarchy of amplifier ICs, operational amplifiers and instrumentation amplifiers support precision measurement, sensor conditioning, current sensing, biomedical instrumentation, and industrial control. The AD625 uses internal resistance networks and gain-control circuitry to provide accurate amplification where fixed-gain amplifiers or discrete op-amp stages would require additional parts.
Key characteristics include user-programmed gains up to 10,000, maximum low gain error of 0.02%, maximum low nonlinearity of 0.001%, a 25 MHz gain-bandwidth product, and a 5 V/µs slew rate. The input-referred noise is listed as 4 nV/√Hz at 1 kHz. These parameters make the AD625BDZ relevant to applications that need programmable sensitivity while maintaining low signal-level distortion and gain accuracy.
The AD625 architecture supports nonstandard gain selections that are not easily realized with conventional fixed-gain devices. Its internal gain network reduces the need for external resistor networks and calibration hardware, while the 25 MHz bandwidth provides signal-rate headroom. Designers must still account for gain-dependent bandwidth, input-referred noise, output swing, and settling behavior when configuring the gain-control interface.
Typical uses include bridge-transducer amplification, precision current measurement, laboratory instrumentation, biomedical sensor interfaces, and low-level differential signal acquisition. The 16-CDIP package favors through-hole construction and applications where ceramic DIP mechanical compatibility, serviceability, or long-term board availability is more important than minimal board area.
For implementation, follow the manufacturer datasheet for the gain-control logic, reference-voltage arrangement, power-supply sequence, decoupling, and output measurement connection. Because the AD625 is not recommended for new designs, engineers should verify lifecycle status, package availability, and qualification requirements against the current Analog Devices product information before committing a new PCB.
This page combines manufacturer lifecycle information, distributor catalog attributes, package and gain details, cross-reference findings, and practical selection guidance. It also distinguishes true package-level replacement candidates from general instrumentation-amplifier alternatives so that obsolete or restricted designs are not migrated without an engineering review.
Alternatif penggantian untuk AD625BDZ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian AD625BDZ (sama faktor bentuk dan footprint) — berbeda di dalam Package, Number of Circuits, Slew Rate, Amplifier Type, RoHS Status.
AD625CDZ
✅ Drop-InKontak untuk harga
Lihat Datasheet →AD625BD/+
✅ Drop-InKontak untuk harga
Lihat Datasheet →AD625BDZ Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Instrumentation |
| Number of Circuits | 1 circuit |
| Programmed Gain Range | Up to 10,000 |
| Maximum Low Gain Error | 0.02% |
| Maximum Low Gain Temperature Coefficient | 5 ppm/°C |
| Maximum Low Nonlinearity | 0.001% |
| Gain-Bandwidth Product | 25 MHz |
| Slew Rate | 5 V/µs |
| Input-Referred Noise | 4 nV/√Hz at 1 kHz |
| Paket | 16-CDIP (0.300 inch, 7.62 mm) |
| Packaging | Tube |
AD625BDZ 16-cdip (0.300 inch, 7.62 mm) Diamant Konfigurasi Panduan
Konfigurasi pin untuk AD625BDZ (16-cdip (0.300 inch, 7.62 mm) pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk AD625BDZ.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
AD625BDZ cocok untuk 6 aplikasis: Bridge Transducer Signal Conditioning, Precision Current Measurement, Biomedical Sensor Interface, Laboratory Measurement Instrumentation, Industrial Process Control, Legacy Sensor Acquisition System.
Bridge Transducer Signal Conditioning
The AD625BDZ fits bridge-based pressure, load, and force measurements where the sensor produces a small differential signal superimposed on a larger common-mode voltage. Its programmable gain up to 10,000 allows the amplifier stage to bring the millivolt-level bridge output into a useful measurement range, while the listed 0.02% maximum low gain error supports accurate scaling. Use the manufacturer application circuit as the starting point, then verify the actual gain, source impedance, excitation voltage, and bandwidth combination. The 25 MHz gain-bandwidth product provides design headroom, but usable bandwidth normally decreases as programmed gain increases. The 16-CDIP format also makes the device practical for instrument panels and laboratory equipment where through-hole serviceability is useful.
Direkomendasikan
Precision Current Measurement
AD625BDZ is applicable to precision current sensing when a shunt produces a small differential voltage that must be amplified without accepting the shunt common-mode voltage as signal. Programmable gain up to 10,000 provides substantial sensitivity for millivolt-level shunt outputs, and the listed 0.001% maximum low nonlinearity helps preserve amplitude relationships during measurement. The design should select a gain that keeps the output within the amplifier's usable swing and should account for the 5 V/µs slew rate when the sensed current changes quickly. Input-referred noise of 4 nV/√Hz at 1 kHz must be combined with shunt resistance and amplifier noise when calculating sensitivity. Differential routing and grounding remain critical because instrumentation amplifiers reject common-mode voltage but do not remove errors caused by mismatched impedances.
Direkomendasikan
Biomedical Sensor Interface
The AD625BDZ can be evaluated for low-level biomedical sensor interfaces when the design requires a differential input, programmable gain, and legacy 16-CDIP support. Gains up to 10,000 are useful for conditioning small physiological or electrode-derived signals, while low gain error and low nonlinearity improve the accuracy of the measurement chain. Because the device is not recommended for new designs, a new medical product should compare a currently supported precision instrumentation amplifier rather than assume that an NRND part is acceptable for a new qualification cycle. Any medical use requires validation of input protection, leakage, patient isolation, electrical safety, and applicable risk-management processes outside the amplifier datasheet. The signal path should also be checked for motion artifacts, electrode impedance, connector noise, and settling time at the selected gain.
Direkomendasikan
Laboratory Measurement Instrumentation
AD625BDZ is well matched to laboratory instruments that measure weak differential signals and need selectable sensitivity without a large external gain-switching network. Programmable gains up to 10,000 support a broad range of source amplitudes, and the 25 MHz gain-bandwidth product plus 5 V/µs slew rate provide useful response margin for moderate-bandwidth instrumentation. The 0.02% maximum low gain error and 0.001% maximum low nonlinearity are relevant when the instrument performs calibrated amplitude measurements. A practical implementation should provide stable excitation, low-noise grounding, and carefully bypassed supply rails. Because the package is a ceramic 16-CDIP rather than a surface-mount package, the part is especially suitable for legacy analytical instruments, modular test systems, and equipment where field replacement and through-hole assembly are more valuable than board-area reduction.
Direkomendasikan
Industrial Process Control
AD625BDZ can be used in industrial process-control front ends that measure differential sensor outputs, provided the electrical ratings and lifecycle status remain appropriate for the equipment. Programmable gain up to 10,000 is useful for normalizing outputs from strain, pressure, and current sensors before conversion or control processing. Its differential architecture suppresses common-mode voltage, helping the stage handle sensors referenced to noisy industrial grounds. The design must still confirm input common-mode range, output swing, supply requirements, and gain-dependent bandwidth against the exact AD625BDZ datasheet. For new control platforms, the not-recommended-for-new-designs status should be treated as a lifecycle constraint. Confirming the AD625CDZ or AD625BD ordering entries is useful when maintaining a standardized platform, but it does not by itself establish drop-in qualification or industrial certification.
Direkomendasikan
Legacy Sensor Acquisition System
AD625BDZ is particularly relevant to legacy sensor-acquisition systems that already use its 16-CDIP footprint and require continuity without redesigning the analog front end. Programmable gains up to 10,000, low gain error, and low nonlinearity make it suitable for preserving established measurement behavior in older industrial, medical, or scientific equipment. The primary engineering issue is lifecycle risk rather than basic functionality: Analog Devices marks the AD625 as not recommended for new designs, so inventory planning and an approved migration path are necessary for long-term support. AD625CDZ and AD625BD should be reviewed against the ordering table for suffix-specific electrical and temperature-grade differences. Before replacing the part in production, compare pin assignments, gain-control logic, offset behavior, noise, bandwidth, and supply requirements, and verify that the new assembly method and ceramic DIP tolerances remain compatible with the PCB.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk AD625BDZ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | AD625CDZ | AD625BD |
|---|---|---|---|
| Package | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Type | Instrumentation | Instrumentation | Instrumentation |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
Diferensiator Kunci
- Programmable gain reaches 10,000 (vsAD625CDZ)
- Low gain error for precision measurement (vsAD625BD)
- Legacy-compatible ceramic DIP construction (vsAD625CDZ)
Catatan Desain
Use the official AD625 datasheet pin-description table to assign the 16-CDIP footprint and to place the gain-control, reference, supply, and measurement connections correctly. Keep input and reference networks close to their associated pins, provide a solid ground plane, and route sensitive differential inputs away from switching nodes. The CDIP lead pitch must match the existing PCB; changing to a surface-mount instrument amplifier requires a footprint and layout redesign rather than a simple component substitution.
Treat the AD625 as a gain-dependent analog stage rather than assuming its 25 MHz gain-bandwidth product applies at every programmed gain. Verify closed-loop bandwidth, settling time, and output slew requirements for the selected gain and sample rate. The listed 4 nV/√Hz input-referred noise at 1 kHz must be integrated over the actual measurement bandwidth and combined with sensor, resistor, and reference noise. This prevents an apparently low-noise amplifier from producing a poor system-level noise floor.
Follow the manufacturer guidance for supply decoupling, grounding, and output-reference connections. Place the required bypass capacitors at the device pins with short, low-inductance traces, and provide separate return paths for input, reference, and output currents. When upgrading a legacy board, inspect existing capacitors and contaminated sockets because long-term electrolytic leakage or high supply impedance can degrade offset and noise performance even when the amplifier itself is unchanged.
Do not infer that every AD625-family suffix is automatically interchangeable. The target is marked not recommended for new designs, and the available comparison records do not fully define suffix-specific gain, temperature-grade, offset, or pinout differences. Before replacing AD625BDZ, verify the manufacturer ordering table and pin descriptions, compare the programmed-gain interface, and confirm the operating-temperature grade and test requirements. Also verify that the replacement remains available in the required 16-CDIP package.
Informasi Konformitas
The available manufacturer and distributor excerpts do not state the AD625BDZ RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Obtain current manufacturer declarations and qualification records before using the part in a regulated program.