Analog Devices

AD625BDZ - Programmable Gain Instrumentation Amplifier | Analog Devices

料号: AD625BDZ ✗ 停产
16-CDIP (0.300 inch, 7.62 mm) Package
最小起订量: 1 |

AD625BDZ 概述

Analog Devices AD625BDZ is a precision programmable-gain instrumentation amplifier packaged in a 16-CDIP ceramic dual in-line package. The device is designed for precision signal conditioning applications requiring user-programmed gains up to 10,000, low gain error, and low output noise. The AD625BDZ is identified by Analog Devices as not recommended for new designs, so engineers should evaluate the current product portfolio before beginning a new design.

An instrumentation amplifier is a differential-input analog IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. Within the broader hierarchy of amplifier ICs, operational amplifiers and instrumentation amplifiers support precision measurement, sensor conditioning, current sensing, biomedical instrumentation, and industrial control. The AD625 uses internal resistance networks and gain-control circuitry to provide accurate amplification where fixed-gain amplifiers or discrete op-amp stages would require additional parts.

Key characteristics include user-programmed gains up to 10,000, maximum low gain error of 0.02%, maximum low nonlinearity of 0.001%, a 25 MHz gain-bandwidth product, and a 5 V/µs slew rate. The input-referred noise is listed as 4 nV/√Hz at 1 kHz. These parameters make the AD625BDZ relevant to applications that need programmable sensitivity while maintaining low signal-level distortion and gain accuracy.

The AD625 architecture supports nonstandard gain selections that are not easily realized with conventional fixed-gain devices. Its internal gain network reduces the need for external resistor networks and calibration hardware, while the 25 MHz bandwidth provides signal-rate headroom. Designers must still account for gain-dependent bandwidth, input-referred noise, output swing, and settling behavior when configuring the gain-control interface.

Typical uses include bridge-transducer amplification, precision current measurement, laboratory instrumentation, biomedical sensor interfaces, and low-level differential signal acquisition. The 16-CDIP package favors through-hole construction and applications where ceramic DIP mechanical compatibility, serviceability, or long-term board availability is more important than minimal board area.

For implementation, follow the manufacturer datasheet for the gain-control logic, reference-voltage arrangement, power-supply sequence, decoupling, and output measurement connection. Because the AD625 is not recommended for new designs, engineers should verify lifecycle status, package availability, and qualification requirements against the current Analog Devices product information before committing a new PCB.

This page combines manufacturer lifecycle information, distributor catalog attributes, package and gain details, cross-reference findings, and practical selection guidance. It also distinguishes true package-level replacement candidates from general instrumentation-amplifier alternatives so that obsolete or restricted designs are not migrated without an engineering review.

直接替换替代料: AD625BDZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: AD625BDZ (相同外形与封装尺寸) ——差异在于 Package, Number of Circuits, Slew Rate, Amplifier Type, RoHS Status.

Analog Devices
Package: 16-CDIP, 0.300-inch (7.62 mm) width
Number of Circuits: 1
Amplifier Type: Programmable-gain instrumentation amplifier
对比 AD625BDZ →
Analog Devices
Package: 16-CDIP
RoHS Status: unknown
Analog Devices
Package: 16-CDIP, 0.300 inch pitch, 7.62 mm body
Slew Rate: 5 V/us
RoHS Status: Listed as RoHS on distributor product information
对比 AD625BDZ →

AD625CDZ

✅ 直接替换
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Instrumentation amplifier · 1 circuit · 25 MHz · 650 kHz · 5 V/us · 10 nA · +5 V · 16-CDIP, 0.300 inch pitch, 7.62 mm body

联系询价

查看数据手册 →

AD625BD/+

✅ 直接替换
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Programmable Gain Instrumentation Amplifier · 1 circuit · 16-CDIP · Programmable gain · Differential input

联系询价

查看数据手册 →

AD625BDZ 最大额定值与电气特性

Amplifier Type Instrumentation
Number of Circuits 1 circuit
Programmed Gain Range Up to 10,000
Maximum Low Gain Error 0.02%
Maximum Low Gain Temperature Coefficient 5 ppm/°C
Maximum Low Nonlinearity 0.001%
Gain-Bandwidth Product 25 MHz
Slew Rate 5 V/µs
Input-Referred Noise 4 nV/√Hz at 1 kHz
封装 16-CDIP (0.300 inch, 7.62 mm)
Packaging Tube

AD625BDZ 16-cdip (0.300 inch, 7.62 mm) 引脚配置指南

AD625BDZ(16-cdip (0.300 inch, 7.62 mm) 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

AD625BDZ 的 16-cdip (0.300 inch, 7.62 mm) 封装引脚图

暂无详细引脚数据: AD625BDZ.

请参阅 数据手册 以查看完整引脚配置。

典型应用

AD625BDZ 适用于 6 应用s: Bridge Transducer Signal Conditioning, Precision Current Measurement, Biomedical Sensor Interface, Laboratory Measurement Instrumentation, Industrial Process Control, Legacy Sensor Acquisition System.

🏭

Bridge Transducer Signal Conditioning

The AD625BDZ fits bridge-based pressure, load, and force measurements where the sensor produces a small differential signal superimposed on a larger common-mode voltage. Its programmable gain up to 10,000 allows the amplifier stage to bring the millivolt-level bridge output into a useful measurement range, while the listed 0.02% maximum low gain error supports accurate scaling. Use the manufacturer application circuit as the starting point, then verify the actual gain, source impedance, excitation voltage, and bandwidth combination. The 25 MHz gain-bandwidth product provides design headroom, but usable bandwidth normally decreases as programmed gain increases. The 16-CDIP format also makes the device practical for instrument panels and laboratory equipment where through-hole serviceability is useful.

⚡

Precision Current Measurement

AD625BDZ is applicable to precision current sensing when a shunt produces a small differential voltage that must be amplified without accepting the shunt common-mode voltage as signal. Programmable gain up to 10,000 provides substantial sensitivity for millivolt-level shunt outputs, and the listed 0.001% maximum low nonlinearity helps preserve amplitude relationships during measurement. The design should select a gain that keeps the output within the amplifier's usable swing and should account for the 5 V/µs slew rate when the sensed current changes quickly. Input-referred noise of 4 nV/√Hz at 1 kHz must be combined with shunt resistance and amplifier noise when calculating sensitivity. Differential routing and grounding remain critical because instrumentation amplifiers reject common-mode voltage but do not remove errors caused by mismatched impedances.

💊

Biomedical Sensor Interface

The AD625BDZ can be evaluated for low-level biomedical sensor interfaces when the design requires a differential input, programmable gain, and legacy 16-CDIP support. Gains up to 10,000 are useful for conditioning small physiological or electrode-derived signals, while low gain error and low nonlinearity improve the accuracy of the measurement chain. Because the device is not recommended for new designs, a new medical product should compare a currently supported precision instrumentation amplifier rather than assume that an NRND part is acceptable for a new qualification cycle. Any medical use requires validation of input protection, leakage, patient isolation, electrical safety, and applicable risk-management processes outside the amplifier datasheet. The signal path should also be checked for motion artifacts, electrode impedance, connector noise, and settling time at the selected gain.

🧪

Laboratory Measurement Instrumentation

AD625BDZ is well matched to laboratory instruments that measure weak differential signals and need selectable sensitivity without a large external gain-switching network. Programmable gains up to 10,000 support a broad range of source amplitudes, and the 25 MHz gain-bandwidth product plus 5 V/µs slew rate provide useful response margin for moderate-bandwidth instrumentation. The 0.02% maximum low gain error and 0.001% maximum low nonlinearity are relevant when the instrument performs calibrated amplitude measurements. A practical implementation should provide stable excitation, low-noise grounding, and carefully bypassed supply rails. Because the package is a ceramic 16-CDIP rather than a surface-mount package, the part is especially suitable for legacy analytical instruments, modular test systems, and equipment where field replacement and through-hole assembly are more valuable than board-area reduction.

🏭

Industrial Process Control

AD625BDZ can be used in industrial process-control front ends that measure differential sensor outputs, provided the electrical ratings and lifecycle status remain appropriate for the equipment. Programmable gain up to 10,000 is useful for normalizing outputs from strain, pressure, and current sensors before conversion or control processing. Its differential architecture suppresses common-mode voltage, helping the stage handle sensors referenced to noisy industrial grounds. The design must still confirm input common-mode range, output swing, supply requirements, and gain-dependent bandwidth against the exact AD625BDZ datasheet. For new control platforms, the not-recommended-for-new-designs status should be treated as a lifecycle constraint. Confirming the AD625CDZ or AD625BD ordering entries is useful when maintaining a standardized platform, but it does not by itself establish drop-in qualification or industrial certification.

🔧

Legacy Sensor Acquisition System

AD625BDZ is particularly relevant to legacy sensor-acquisition systems that already use its 16-CDIP footprint and require continuity without redesigning the analog front end. Programmable gains up to 10,000, low gain error, and low nonlinearity make it suitable for preserving established measurement behavior in older industrial, medical, or scientific equipment. The primary engineering issue is lifecycle risk rather than basic functionality: Analog Devices marks the AD625 as not recommended for new designs, so inventory planning and an approved migration path are necessary for long-term support. AD625CDZ and AD625BD should be reviewed against the ordering table for suffix-specific electrical and temperature-grade differences. Before replacing the part in production, compare pin assignments, gain-control logic, offset behavior, noise, bandwidth, and supply requirements, and verify that the new assembly method and ceramic DIP tolerances remain compatible with the PCB.

推荐产品汇总

AD625CDZ Analog Devices 用于: Bridge Transducer Signal Conditioning, Precision Current Measurement, Biomedical Sensor Interface, Laboratory Measurement Instrumentation, Industrial Process Control, Legacy Sensor Acquisition System AD625BD AD625-family orderable variant 用于: Bridge Transducer Signal Conditioning, Precision Current Measurement, Biomedical Sensor Interface, Laboratory Measurement Instrumentation, Industrial Process Control, Legacy Sensor Acquisition System
What is the AD625BDZ?
The AD625BDZ is a single-circuit, precision programmable-gain instrumentation amplifier from Analog Devices, supplied in a 16-CDIP ceramic DIP package. According to the manufacturer product page and datasheet, it supports user-programmed gains up to 10,000 and is intended for precision differential-signal conditioning. The device is marked not recommended for new designs, so it is primarily relevant to existing designs, maintenance, and qualified legacy platforms.
What is the gain range of the AD625BDZ?
The AD625BDZ supports user-programmed gains up to 10,000. The manufacturer describes the AD625 as a precision instrumentation amplifier for nonstandard gains that are difficult to obtain with conventional fixed-gain devices such as the AD524 or AD624. Gain programming is handled internally, reducing the need for external switchable resistor networks while preserving accurate gain selection for transducer and low-level sensor signals.
What is the noise performance of AD625BDZ?
The AD625BDZ has a listed input-referred noise density of 4 nV/√Hz at 1 kHz. This specification is important when the amplifier handles millivolt-level differential signals because input-referred noise contributes directly to the measured signal-to-noise ratio. Noise performance remains gain dependent, so engineers should check the gain setting, bandwidth, source impedance, and sensor noise before finalizing the signal-chain budget.
What package does AD625BDZ use?
The AD625BDZ uses a 16-CDIP package measuring 0.300 inch, or 7.62 mm, across the lead span, and distributor catalog data identifies tube packaging. The manufacturer product page and distributor listings identify the part as a single instrumentation amplifier. Because CDIP is a through-hole ceramic package, the footprint differs from surface-mount SOIC and DIP alternatives and cannot be substituted without PCB changes.
Where can I download the AD625BDZ datasheet?
The official AD625 datasheet and product documentation are available from the Analog Devices AD625 product page at https://www.analog.com/en/products/ad625.html. That page is the preferred source for the pin description, gain-control truth table, electrical characteristics, application circuit, and ordering information. Use the manufacturer pin-description table when assigning PCB tracks and verify the package suffix before releasing a layout.
Where can I find the AD625BDZ pinout?
The AD625BDZ pinout must be taken from the pin-description table in the official Analog Devices AD625 datasheet linked from the product page. The searchable catalog excerpt confirms a 16-CDIP package but does not reproduce the individual terminal assignments, so this page does not infer pin names from a generic package diagram. Use the 16-lead CDIP outline and the manufacturer pin table together when laying out the board.
Is AD625BDZ suitable for new designs?
The AD625BDZ is not recommended for new designs according to the Analog Devices product page. Its NRND status makes it appropriate for maintaining an existing design when the original footprint and behavior must be preserved. For a new design, engineers should review currently recommended precision instrumentation amplifiers and confirm gain range, bandwidth, noise, supply voltage, package, and lifecycle requirements before migration.
What is the AD625BDZ vs AD625CDZ difference?
AD625BDZ and AD625CDZ are both AD625-family instrumentation amplifiers listed for comparison, but the available catalog excerpt does not identify the parameter that distinguishes the BZ and CZ suffixes. Both are associated with the AD625 precision programmable-gain family, whose core characteristics include gains up to 10,000, 0.02% maximum low gain error, and 0.001% maximum low nonlinearity. Confirm the suffix-specific ordering table and temperature grade before treating one as a drop-in replacement.
When should I choose AD625BDZ over another instrumentation amplifier?
Choose the AD625BDZ when an existing system requires the exact AD625BDZ function, 16-CDIP footprint, and programmable gain behavior, especially during repair or lifecycle extension. Its 10,000 maximum programmed gain, 0.02% maximum low gain error, and 25 MHz gain-bandwidth product are useful for precision low-level measurements. For new designs, select an amplifier that is currently recommended and verify that its gain-control interface and package meet the system requirements.
Is AD625BDZ suitable for bridge and sensor measurements?
Yes, AD625BDZ is suitable for bridge-transducer and low-level differential sensor measurements when the required gain and bandwidth are within its capability. Programmable gains up to 10,000 and input-referred noise of 4 nV/√Hz at 1 kHz support precision signal acquisition. The design must account for gain-dependent bandwidth, common-mode range, output swing, sensor excitation noise, and the instrumentation-amplifier input architecture shown in the manufacturer application circuit.
What is the best drop-in replacement for AD625BDZ?
No replacement can be declared a guaranteed drop-in substitute from the available cross-reference results. AD625CDZ is the closest explicitly identified AD625-family comparison candidate, but the available data does not establish every suffix-specific electrical, temperature, and pin-compatibility requirement. Before replacing AD625BDZ, compare the manufacturer ordering tables and pin descriptions and confirm gain logic, supply range, offset, noise, bandwidth, and package dimensions.
What can replace AD625BDZ?
AD625CDZ is a candidate for an engineering review, but the available information does not prove that it is a drop-in replacement for AD625BDZ. The cross-reference results identify the AD625 family and a direct comparison with AD625CDZ, while the manufacturer data establishes the target's 16-CDIP construction and programmable-gain architecture. Use the official AD625 ordering table and pin descriptions to confirm suffix, grade, and terminal compatibility.
Where can I buy AD625BDZ online?
Use the Request a Quote form on this page to request AD625BDZ availability, lot conditions, and lead time. The part is identified by Analog Devices as not recommended for new designs, so supply status can vary with remaining inventory and legacy demand. Specify the exact AD625BDZ suffix, tube-packaging requirement, quantity, date code, and any inspection requirements when requesting a quotation.
What is the price of AD625BDZ?
Pricing for AD625BDZ should be confirmed through the Request a Quote form on this page because this is a not-recommended-for-new-designs part and commercial terms depend on quantity, traceability, condition, and remaining supply. The manufacturer lists the AD625 family as not recommended for new designs. Supply planning should therefore account for possible allocation constraints and avoid assuming that legacy inventory can be replenished indefinitely.
What is the lead time and stock status for AD625BDZ?
Use the Request a Quote form on this page to request current AD625BDZ stock, lead time, minimum order quantity, and date-code information. The manufacturer identifies the AD625 as not recommended for new designs, which makes remaining-stock confirmation especially important for maintenance schedules. For production continuity, request enough quantity for the planned service period and evaluate an approved current alternative for future revisions.
What are the key specifications engineers should know about AD625BDZ?
AD625BDZ is a one-circuit programmable-gain instrumentation amplifier in a 16-CDIP package. Its principal listed characteristics are user-programmed gains up to 10,000, maximum low gain error of 0.02%, maximum low nonlinearity of 0.001%, a 25 MHz gain-bandwidth product, a 5 V/µs slew rate, and 4 nV/√Hz input-referred noise at 1 kHz. The manufacturer also identifies the device as not recommended for new designs, making lifecycle planning essential.
Does AD625BDZ meet RoHS and automotive qualification requirements?
The available product information does not state the AD625BDZ RoHS, REACH, or automotive-qualification status, so those requirements cannot be confirmed from this page. The AD625BDZ is not identified as an AEC-Q100-qualified automotive variant in the available manufacturer description. For a regulated or automotive program, request the current manufacturer declaration and product-qualification documentation before treating the part as compliant or qualified.

工程参考数据: AD625BDZ ——对比、设计指导和合规信息。

选型指南

Choose AD625BDZ when maintaining an existing 16-CDIP instrument-amplifier board that depends on programmable gains up to 10,000, low gain error, and low nonlinearity. Its 25 MHz gain-bandwidth product and 5 V/µs slew rate provide useful analog performance, but the not-recommended-for-new-designs status makes it less attractive for a new platform unless continuity or qualification requirements justify the lifecycle risk. Consider AD625CDZ for a family-level comparison, then verify its ordering suffix, temperature grade, gain-control logic, and pin description before replacement. AD625BD is another family candidate whose suffix-specific ratings should also be checked. If PCB area, automated assembly, or long-term product continuity drives the design, evaluate a currently recommended surface-mount precision instrumentation amplifier and plan the required footprint and signal-path changes rather than assuming a drop-in migration.

与替代料对比

参数 本产品 AD625CDZ AD625BD
Package 16-CDIP (0.300 inch, 7.62 mm) 16-CDIP (0.300 inch, 7.62 mm) 16-CDIP (0.300 inch, 7.62 mm)
Brand Analog Devices Analog Devices Analog Devices
Amplifier Type Instrumentation Instrumentation Instrumentation
Number of Circuits 1 circuit 1 circuit 1 circuit

关键差异点

  • Programmable gain reaches 10,000 (对比 AD625CDZ)
  • Low gain error for precision measurement (对比 AD625BD)
  • Legacy-compatible ceramic DIP construction (对比 AD625CDZ)

设计说明

Use the official AD625 datasheet pin-description table to assign the 16-CDIP footprint and to place the gain-control, reference, supply, and measurement connections correctly. Keep input and reference networks close to their associated pins, provide a solid ground plane, and route sensitive differential inputs away from switching nodes. The CDIP lead pitch must match the existing PCB; changing to a surface-mount instrument amplifier requires a footprint and layout redesign rather than a simple component substitution.

Treat the AD625 as a gain-dependent analog stage rather than assuming its 25 MHz gain-bandwidth product applies at every programmed gain. Verify closed-loop bandwidth, settling time, and output slew requirements for the selected gain and sample rate. The listed 4 nV/√Hz input-referred noise at 1 kHz must be integrated over the actual measurement bandwidth and combined with sensor, resistor, and reference noise. This prevents an apparently low-noise amplifier from producing a poor system-level noise floor.

Follow the manufacturer guidance for supply decoupling, grounding, and output-reference connections. Place the required bypass capacitors at the device pins with short, low-inductance traces, and provide separate return paths for input, reference, and output currents. When upgrading a legacy board, inspect existing capacitors and contaminated sockets because long-term electrolytic leakage or high supply impedance can degrade offset and noise performance even when the amplifier itself is unchanged.

Do not infer that every AD625-family suffix is automatically interchangeable. The target is marked not recommended for new designs, and the available comparison records do not fully define suffix-specific gain, temperature-grade, offset, or pinout differences. Before replacing AD625BDZ, verify the manufacturer ordering table and pin descriptions, compare the programmed-gain interface, and confirm the operating-temperature grade and test requirements. Also verify that the replacement remains available in the required 16-CDIP package.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The available manufacturer and distributor excerpts do not state the AD625BDZ RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Obtain current manufacturer declarations and qualification records before using the part in a regulated program.

相关搜索

ad625 datasheet AD625BDZ datasheet AD625BDZ pinout AD625BDZ datasheet pdf AD625BDZ equivalent AD625BDZ replacement AD625BDZ cross reference AD625BDZ vs AD625CDZ AD625BDZ 16-CDIP AD625BDZ programmable gain AD625BDZ noise 4 nV AD625BDZ instrumentation amplifier AD625BDZ price AD625BDZ stock Analog Devices AD625BDZ

相关元器件 & 术语

Analog Devices AD625BDZ AD625CDZ AD625BD AD625 precision instrumentation amplifier programmable gain amplifier analog amplifier IC differential input common-mode rejection gain-bandwidth product slew rate gain error nonlinearity input-referred noise 16-CDIP ceramic dual in-line package through-hole package surface mount bridge transducer current shunt biomedical sensor industrial process control laboratory instrumentation
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情