Analog Devices

AD713KN - Quad Precision 4 MHz BiFET Op Amp | Analog Devices

MPN: AD713KN ✗ Akhir Hidup
0.5 mV for AD713K grade Vdss 14-pin PDIP Package 2 µV peak-to-peak from 0.1 Hz to 10 Hz Speed
MOQ: 1 |

AD713KN Ringkasan

Analog Devices AD713KN is a quad precision operational amplifier integrating four AD711 BiFET amplifier sections in a 14-pin PDIP package. Its headline specifications include a 4 MHz unity-gain bandwidth, 20 V/µs slew rate, and approximately 1 µs settling to 0.01% for a 10 V step. The monolithic construction also provides close matching of AC and DC characteristics among the four amplifier channels, making the device useful when multiple signal paths require consistent behavior.

An operational amplifier is a high-gain differential voltage amplifier intended for feedback-controlled signal conditioning. The AD713 belongs to the BiFET operational-amplifier hierarchy, combining low input bias current with relatively high bandwidth and slew rate. Four matched amplifiers in one package can reduce component count in instrumentation, audio, communication, and control circuits while preserving consistent propagation and settling behavior across channels.

Important performance characteristics include 0.0003% total harmonic distortion, 150 V/mV minimum open-loop gain, and a specified 14-bit accuracy claim. Depending on the selected AD713 grade, offset voltage and drift specifications differ; the AD713K-grade information identifies 0.5 mV maximum offset voltage and 20 mV/°C maximum drift. Low-frequency input noise is listed as 2 µV peak-to-peak from 0.1 Hz to 10 Hz, which supports precision signal-chain applications where input-referred noise affects usable resolution.

The AD713 architecture uses four BiFET amplifier sections on one monolithic die. Matching between amplifiers on the same die improves consistency of offset, drift, gain, bandwidth, and dynamic behavior. Its 4 MHz unity-gain bandwidth permits operation beyond the low-frequency precision region, while the 20 V/µs slew rate provides faster large-signal response than conventional precision amplifiers with substantially narrower bandwidth. The device can therefore serve precision buffers, active filters, and general-purpose signal-conditioning stages where both dc accuracy and ac performance matter.

Typical applications include audio preamplification and active filtering, low-level instrumentation, data-acquisition input conditioning, process-control signals, communications equipment, and four-channel measurement systems. Using one quad package instead of four separate amplifiers can simplify routing and maintain channel-to-channel consistency. However, thermal performance and input common-mode limitations must be checked against the manufacturer datasheet for each operating condition.

For PCB design, place bypass capacitors close to the power pins and keep feedback networks close to their associated amplifier pins. Maintain short, low-impedance ground returns and avoid routing sensitive input signals beside high-current outputs. Because this is a through-hole PDIP device, observe the correct pin-1 orientation and verify pin functions against the Analog Devices AD713 datasheet before fabrication.

This product page consolidates the AD713KN electrical characteristics, obsolete-life-cycle information, archival price reference, packaging details, and a qualified drop-in assessment. It also distinguishes verified replacement information from assumptions, helping engineers decide whether the AD713KN remains appropriate for repairs, legacy equipment, and newly qualified designs.

Alternatif penggantian untuk AD713KN — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

AD713KNZ

✅ Drop-In
📦 14-pin PDIP
Same 14-pin PDIP footprint and consistent terminals; documented as a complete replacement with no modification required

📋 Alternatif referensi (tidak dalam katalog)

AD713KN Rating Maksimal & Karakteristik Listrik

Amplifier Configuration Quad operational amplifier
Internal Amplifier Sections 4 AD711 BiFET operational amplifiers
Unity-Gain Bandwidth 4 MHz
Slew Rate 20 V/µs
Settling Time 1 µs to 0.01% for a 10 V step
Total Harmonic Distortion 0.0003%
Maximum Offset Voltage 0.5 mV for AD713K grade
Maximum Offset Drift 20 mV/°C for AD713K grade
Minimum Open-Loop Gain 150 V/mV
Low-Frequency Input Noise 2 µV peak-to-peak from 0.1 Hz to 10 Hz
Tegangan Pemuat ±18 V maximum
Accuracy 14-bit accuracy claim
Paket 14-pin PDIP
Tipe Mounting Through-hole
Temperature Grade Commercial grade
Number of Terminals 14 terminals

AD713KN 14-pin pdip Diamant Konfigurasi Panduan

Konfigurasi pin untuk AD713KN (14-pin pdip pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 14-pin pdip untuk AD713KN

Tidak ada data diatribut pin yang tersedia untuk AD713KN.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

AD713KN cocok untuk 6 aplikasis: Precision Active Filtering, Audio Signal Conditioning, Industrial Instrumentation, Data Acquisition Front Ends, Process Control Loops, Test and Measurement Equipment.

🔧

Precision Active Filtering

The AD713KN fits precision active-filter stages that need more bandwidth than a conventional precision op amp while retaining low offset and closely matched channels. Its 4 MHz unity-gain bandwidth supports useful loop gain at moderate signal frequencies, and the 20 V/µs slew rate improves large-signal behavior. Four amplifiers on one monolithic die can implement state-variable, low-pass, high-pass, or notch sections with consistent device characteristics. The design should account for output swing, noise gain, stability with the selected capacitor values, and the 14-pin PDIP lead capacitance. Decoupling capacitors should be placed close to the supply pins, while feedback resistors and capacitors should remain compact to minimize parasitic coupling and phase shifts.

🎧

Audio Signal Conditioning

AD713KN can condition low-level audio signals in mixer, preamplifier, and balanced-input stages where four amplifier channels reduce board area. The 4 MHz unity-gain bandwidth is ample for many audio-band applications, while the 20 V/µs slew rate permits cleaner handling of larger transients than a very slow precision amplifier. Its specified 0.0003% THD and 2 µV peak-to-peak low-frequency noise support low-distortion signal paths, although system noise also depends on resistor selection and grounding. Use identical feedback networks for channels that need closely matched gain, and keep the unused amplifier section properly biased according to the manufacturer guidance.

🏭

Industrial Instrumentation

The AD713KN is appropriate for industrial instrumentation requiring several precision voltage-buffer channels in a compact through-hole package. The quad arrangement can condition outputs from sensors, transducers, and laboratory instrumentation while its 4 MHz bandwidth handles higher-frequency components more effectively than a narrow-band precision amplifier. The monolithic die provides close matching of AC and DC characteristics between channels, which is valuable in multichannel measurement systems. Designers should verify the input common-mode range against sensor output levels, calculate offset and drift error at the intended temperature, and provide clean grounding. Add supply bypass capacitance near the package and avoid long, high-impedance traces that can increase noise pickup and settling error.

📊

Data Acquisition Front Ends

AD713KN can provide four buffered inputs for a data-acquisition front end, placing a unity-gain or modest-gain buffer between a sensor network and subsequent converter. The 150 V/mV minimum open-loop gain supports accurate voltage-following operation, while the 4 MHz unity-gain bandwidth reduces the likelihood that the amplifier itself becomes the dominant bandwidth limitation in moderate-speed systems. Offset, drift, noise, and input bias current must be included in the total acquisition error budget. Keep sensor returns and amplifier grounds joined at a controlled point, use short feedback loops, and select external resistors with suitable noise and temperature coefficients for high-resolution measurements.

⚙️

Process Control Loops

The four matched amplifier sections in AD713KN can support comparator, current-buffer, error-amplifier, and signal-conditioning functions in process-control equipment. Its 20 V/µs slew rate allows faster response than many precision-only amplifiers, while the close AC and DC matching of monolithic channels is useful when several control or measurement signals are processed similarly. Choose feedback and compensation components carefully to maintain stability, particularly around sensor poles and actuator delays. The amplifier must remain within its input common-mode range and output swing throughout control transients. For repair of older control systems, AD713KNZ provides the clearest documented drop-in route, subject to electrical and lifecycle qualification.

🖥️

Test and Measurement Equipment

AD713KN can serve as a buffer or active element in test and measurement instruments requiring several consistent amplifier channels. The 4 MHz unity-gain bandwidth is useful for moderate-bandwidth measurement paths, and the monolithic quad implementation helps maintain similar response across input or output channels. Its 0.5 mV maximum offset for the AD713K grade makes it relevant to low-level voltage measurements, but the complete error budget must also include bias current, drift, noise, resistor tolerance, and reference accuracy. Place the device away from high-energy switching nodes, use low-leakage protection components where necessary, and validate settling behavior with the complete external network rather than relying only on the amplifier's unity-gain bandwidth.

Ringkasan Produk Direkomendasikan

AD713KNZ Same-family drop-in replacement Digunakan di dalam: Precision Active Filtering, Audio Signal Conditioning, Industrial Instrumentation, Data Acquisition Front Ends, Process Control Loops, Test and Measurement Equipment AD712 Related dual precision BiFET amplifier Digunakan di dalam: Precision Active Filtering, Industrial Instrumentation, Data Acquisition Front Ends, Test and Measurement Equipment AD711 Single amplifier section used within AD713 Digunakan di dalam: Audio Signal Conditioning, Industrial Instrumentation, Data Acquisition Front Ends, Process Control Loops, Test and Measurement Equipment
What are the key specifications of AD713KN that engineers should know?
The AD713KN is a quad precision BiFET operational amplifier with four AD711 sections, a 4 MHz unity-gain bandwidth, a 20 V/µs slew rate, and approximately 1 µs settling to 0.01% for a 10 V step. According to the Analog Devices AD713 product page and manufacturer datasheet, its monolithic construction provides close matching of AC and DC characteristics between channels. The AD713K grade is listed with 0.5 mV maximum offset voltage and 20 mV/°C maximum drift. It is supplied in a 14-pin PDIP package and is suitable for precision buffering, filtering, audio, instrumentation, and general signal-conditioning applications.
Where can I download the AD713KN datasheet PDF?
The official AD713KN documentation is available through the Analog Devices AD713 product page at analog.com, with a direct manufacturer datasheet also indexed at alldatasheet.com. The manufacturer page is the preferred source for the AD713 family electrical characteristics, package drawings, ordering information, and pin descriptions. Review the pin-assignment section and the obsolete-product notice before using the component in a new design. The AD713KN suffix identifies the 14-pin PDIP configuration, while related suffixes can represent different package or temperature-grade options.
Where can I find the AD713KN pinout?
The AD713KN pinout is documented in the pin-configuration section of the Analog Devices AD713 manufacturer datasheet and on the AD713KN datasheet PDF indexed by AllDataSheet. The device uses a 14-pin PDIP package with four amplifier sections. Before assigning PCB nets, verify the offset null, inverting input, non-inverting input, output, positive-supply, and negative-supply connections against the exact datasheet revision. Do not infer a replacement's pinout solely from its amplifier count; each channel's pin order must be confirmed for the selected package.
Can AD713KNZ replace AD713KN?
Yes, AD713KNZ is a documented drop-in replacement candidate for AD713KN because both use the same 14-pin PDIP configuration and retain consistent terminals and functional characteristics. The FindIC comparison identifies AD713KNZ as a complete replacement requiring no modification. The manufacturer naming convention indicates a packaging-code difference, but the exact ordering information and electrical grade should still be checked before substitution. The AD713KN remains obsolete, so verify lifecycle status, traceability, and any required qualification before using either package variant in production equipment.
What can replace AD713KN in an existing circuit?
AD713KNZ is the clearest documented drop-in replacement for AD713KN because it retains the same 14-pin PDIP footprint, pin arrangement, and amplifier functionality. It is rated as a complete replacement without circuit modification. The replacement should be qualified against the original system's supply voltage, input common-mode range, output swing, noise, bandwidth, offset, drift, and load requirements. Analog Devices lists AD713KN as obsolete, making a documented same-family replacement preferable to an unqualified third-party substitution.
What is the difference between AD713KN and AD713KNZ?
The principal documented difference between AD713KN and AD713KNZ is the ordering or packaging suffix, while both correspond to the AD713 family in a 14-pin PDIP configuration. FindIC reports that AD713KNZ can completely replace AD713KN because the terminals, package, and principal performance characteristics are consistent. For engineering use, confirm the exact suffix ordering table and full operating limits in the Analog Devices documentation rather than treating suffix equivalence as permission to ignore temperature-grade, lead, or qualification requirements.
Is AD713KN suitable for precision instrumentation and active filters?
Yes, AD713KN is suitable for precision instrumentation and moderate-bandwidth active-filter circuits. Its 4 MHz unity-gain bandwidth, 150 V/mV minimum open-loop gain, and 20 V/µs slew rate provide useful dynamic performance for low-level signal conditioning. The AD713K grade is listed with 0.5 mV maximum offset voltage, while the monolithic four-channel construction promotes consistent dc and AC matching. Confirm the input common-mode range, output swing, stability, noise, and supply requirements against the manufacturer datasheet for the exact operating point.
When should I choose AD713KN over a general-purpose quad op amp?
Choose AD713KN when a legacy circuit requires a matched quad BiFET amplifier with 4 MHz unity-gain bandwidth, 20 V/µs slew rate, and precision-oriented offset and noise behavior. It is especially relevant for repairs of equipment designed around the original AD713. For a new design, account for its obsolete lifecycle and evaluate the documented AD713KNZ replacement or another currently supported amplifier after checking the entire signal chain. A general-purpose TL084-class amplifier may offer similar functionality, but it should not be treated as an unqualified drop-in choice.
What is the AD713KN power supply range?
The AD713KN is identified as a ±18 V maximum general-purpose operational amplifier, indicating operation around a maximum total supply of 36 V. Exact minimum, typical, and maximum supply limits should be taken from the Analog Devices AD713 manufacturer datasheet for the relevant grade and package. Both positive and negative rails must remain within the absolute maximum ratings, including during power-up, shutdown, and fault conditions. Confirm input common-mode and output-swing limits because a valid supply voltage alone does not guarantee linear operation.
How much thermal dissipation does the AD713KN allow?
The AD713KN's allowable dissipation depends on the exact supply voltage, output swing, load current, ambient temperature, and PCB thermal path, none of which is fixed by the product listing. A useful design calculation is estimated power dissipation, Pd = (Vsupply − Vswing) × Iload, followed by junction-temperature estimation using the package thermal resistance from the manufacturer datasheet. Because this is a 14-pin PDIP device, lead length, copper area, airflow, and neighboring heat sources can materially change the result. Do not use a generic thermal rating as a substitute for the datasheet limits.
What design considerations matter when using four AD713KN amplifier channels?
Keep each feedback network short and place it close to its associated amplifier channel to minimize parasitic feedback and instability. Route high-impedance inputs away from output and supply-return paths, and connect the power-supply bypass capacitors close to the device. Use a common, low-impedance ground reference for all four channels when channel matching is important. Because AD713 is monolithic, the channels share package and die characteristics, but trace routing, loading, and grounding can still create practical differences between channels.
Is AD713KN in stock, and what is its current availability?
The AD713KN is listed as obsolete, and current availability should be confirmed through the Request a Quote form on this page. Its historical last transaction was recorded in February 2001, so it should not be assumed to be a readily stocked, current-production device. For maintenance work, provide the original assembly and revision details when requesting sourcing support. For new production, use a documented replacement such as AD713KNZ after completing package, pinout, electrical, and qualification checks.
What is the price of AD713KN?
The AD713KN is an obsolete component, and its current commercial terms should be requested through the Request a Quote form on this page. The structured price reference on this page records an archival unit-price observation from 2001, but that historical value does not represent current availability or a guaranteed quotation. Submit the required quantity, package, and inspection requirements with the request so the sourcing team can confirm any new supply, traceability, and lifecycle constraints.
What is the lead time for AD713KN?
The current lead time for AD713KN should be confirmed through the Request a Quote form because the device is listed as obsolete and no current stock commitment is shown. Lead time depends on remaining manufacturer or authorized inventory, quantity, inspection level, and whether a new-production alternative is acceptable. For repair schedules, request a time-critical quotation and include the original equipment date code. For new designs, ask for both AD713KN availability and AD713KNZ lifecycle information so production planning can avoid depending on an end-of-life component.
Where can I buy AD713KN online?
Use the Request a Quote form on this page to request AD713KN pricing, availability, and lead time from XAIPART. The component is listed as obsolete, so live inventory can be limited and may consist of remaining stock rather than ongoing manufacturer production. Include the required quantity, package, date-code preference, and any inspection or traceability requirements. For new designs, AD713KNZ is a documented same-package replacement candidate and should be evaluated before committing the design to the obsolete original.
Does the AD713KN support RoHS or automotive qualification?
RoHS and AEC-Q100 status for the exact AD713KN ordering code are not stated in the manufacturer page text available for this component, so compliance must be confirmed from the current Analog Devices product documentation or the supplier's declaration. The AD713KN is identified as a commercial-grade, through-hole device rather than an automotive-qualified variant. Do not infer RoHS, REACH, lead-free, halogen-free, or conflict-minerals status from the package code alone. Obtain lot-specific documentation when compliance traceability is a procurement requirement.

Data referensi engineering untuk AD713KN — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose AD713KN when repairing legacy equipment that specifically requires the original 14-pin PDIP AD713 amplifier and its documented precision BiFET performance. The device provides four matched amplifier sections, 4 MHz unity-gain bandwidth, 20 V/µs slew rate, and low offset behavior in a single monolithic package. For maintenance and long-term availability, AD713KNZ is the preferred documented drop-in candidate because its package, terminals, and functional characteristics match without circuit modification. Do not choose a generic TL084-class amplifier solely from the 14-pin package outline; verify pin order, dc accuracy, noise, bias current, bandwidth, stability, and input common-mode range. For a new design, favor a currently supported amplifier unless reproducing the original circuit, confirming legacy loading, and performing full electrical qualification make the AD713 family necessary.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini AD713KNZ
Brand Analog Devices Analog Devices
Package 14-pin PDIP 14-pin PDIP
Amplifier Configuration Quad operational amplifier Quad operational amplifier
Internal Amplifier Sections 4 AD711 BiFET amplifiers AD713 family quad BiFET amplifier
Pin Compatibility 14-pin PDIP Pin-to-pin replacement without modification

Diferensiator Kunci

  • Four matched BiFET amplifiers on one monolithic die (vsAD713KNZ)
  • 4 MHz bandwidth with 20 V/µs slew rate (vsAD713KNZ)
  • Low offset and drift for the AD713K grade (vsAD713KNZ)

Catatan Desain

Place power-supply bypass capacitors close to the AD713KN power pins and connect them to a low-impedance ground plane. Keep each channel's feedback components close to the corresponding amplifier pins to minimize parasitic capacitance in the feedback loop. Route high-impedance input nodes away from outputs, supply-current paths, and switching nodes. For a 14-pin PDIP, follow the manufacturer pin orientation exactly and leave sufficient spacing around adjacent leads to avoid solder bridges during manual rework.

The 4 MHz unity-gain bandwidth makes the AD713KN substantially faster than a conventional precision-only amplifier, so stability must be checked with the actual feedback network and load. Estimate closed-loop response using the noise gain rather than signal gain, and include capacitor tolerances and stray capacitance in the assessment. Add an isolation resistor where capacitive loading could create peaking or oscillation. Validate settling and overshoot with the complete analog section because additional poles outside the amplifier can materially change the result.

Do not treat any 14-pin quad op amp as an automatic replacement for AD713KN. Pin ordering, offset limits, noise, bandwidth, input bias current, common-mode range, and output swing must all be compatible with the original circuit. For AD713KN specifically, use the manufacturer pin-description table when assigning tracks and confirm the exact temperature grade. If the circuit relies on the closely matched channels of the monolithic AD713 die, verify that the proposed replacement provides equivalent channel matching rather than merely identical package dimensions.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The component is identified as a commercial-grade 14-pin PDIP operational amplifier. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated and should be confirmed for the exact ordering code and manufacturing lot.

Pencarian Terkait

AD713KN datasheet AD713KN datasheet pdf AD713KN pinout AD713KN replacement AD713KN equivalent AD713KN cross reference AD713KN vs AD713KNZ Analog Devices AD713KN AD713KN 14-pin PDIP AD713KN 4 MHz op amp AD713KN price AD713KN stock

Komponen dan Istilah Terkait

Analog Devices AD713KN AD713KNZ AD713 AD711 AD712 quad operational amplifier BiFET operational amplifier precision operational amplifier signal-conditioning IC semiconductor 14-pin PDIP PDIP package through-hole package unity-gain bandwidth slew rate settling time offset voltage offset drift total harmonic distortion open-loop gain input noise active filter instrumentation data acquisition
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ