AD713KN - Quad Precision 4 MHz BiFET Op Amp | Analog Devices
MPN: AD713KN ✗ پایان تولیدAD713KN نمای کلی
An operational amplifier is a high-gain differential voltage amplifier intended for feedback-controlled signal conditioning. The AD713 belongs to the BiFET operational-amplifier hierarchy, combining low input bias current with relatively high bandwidth and slew rate. Four matched amplifiers in one package can reduce component count in instrumentation, audio, communication, and control circuits while preserving consistent propagation and settling behavior across channels.
Important performance characteristics include 0.0003% total harmonic distortion, 150 V/mV minimum open-loop gain, and a specified 14-bit accuracy claim. Depending on the selected AD713 grade, offset voltage and drift specifications differ; the AD713K-grade information identifies 0.5 mV maximum offset voltage and 20 mV/°C maximum drift. Low-frequency input noise is listed as 2 µV peak-to-peak from 0.1 Hz to 10 Hz, which supports precision signal-chain applications where input-referred noise affects usable resolution.
The AD713 architecture uses four BiFET amplifier sections on one monolithic die. Matching between amplifiers on the same die improves consistency of offset, drift, gain, bandwidth, and dynamic behavior. Its 4 MHz unity-gain bandwidth permits operation beyond the low-frequency precision region, while the 20 V/µs slew rate provides faster large-signal response than conventional precision amplifiers with substantially narrower bandwidth. The device can therefore serve precision buffers, active filters, and general-purpose signal-conditioning stages where both dc accuracy and ac performance matter.
Typical applications include audio preamplification and active filtering, low-level instrumentation, data-acquisition input conditioning, process-control signals, communications equipment, and four-channel measurement systems. Using one quad package instead of four separate amplifiers can simplify routing and maintain channel-to-channel consistency. However, thermal performance and input common-mode limitations must be checked against the manufacturer datasheet for each operating condition.
For PCB design, place bypass capacitors close to the power pins and keep feedback networks close to their associated amplifier pins. Maintain short, low-impedance ground returns and avoid routing sensitive input signals beside high-current outputs. Because this is a through-hole PDIP device, observe the correct pin-1 orientation and verify pin functions against the Analog Devices AD713 datasheet before fabrication.
This product page consolidates the AD713KN electrical characteristics, obsolete-life-cycle information, archival price reference, packaging details, and a qualified drop-in assessment. It also distinguishes verified replacement information from assumptions, helping engineers decide whether the AD713KN remains appropriate for repairs, legacy equipment, and newly qualified designs.
جایگزینهای drop-in برای AD713KN — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
AD713KNZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD713KN حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Configuration | Quad operational amplifier |
| Internal Amplifier Sections | 4 AD711 BiFET operational amplifiers |
| Unity-Gain Bandwidth | 4 MHz |
| Slew Rate | 20 V/µs |
| Settling Time | 1 µs to 0.01% for a 10 V step |
| Total Harmonic Distortion | 0.0003% |
| Maximum Offset Voltage | 0.5 mV for AD713K grade |
| Maximum Offset Drift | 20 mV/°C for AD713K grade |
| Minimum Open-Loop Gain | 150 V/mV |
| Low-Frequency Input Noise | 2 µV peak-to-peak from 0.1 Hz to 10 Hz |
| ولتاژ تغذیه | ±18 V maximum |
| Accuracy | 14-bit accuracy claim |
| بستهبندی | 14-pin PDIP |
| نوع نصب | Through-hole |
| Temperature Grade | Commercial grade |
| Number of Terminals | 14 terminals |
راهنمای پیکربندی پین AD713KN 14-pin pdip
پیکربندی پین برای AD713KN (پکیج 14-pin pdip). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای AD713KN.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
AD713KN مناسب است برای 6 کاربردs: Precision Active Filtering, Audio Signal Conditioning, Industrial Instrumentation, Data Acquisition Front Ends, Process Control Loops, Test and Measurement Equipment.
Precision Active Filtering
The AD713KN fits precision active-filter stages that need more bandwidth than a conventional precision op amp while retaining low offset and closely matched channels. Its 4 MHz unity-gain bandwidth supports useful loop gain at moderate signal frequencies, and the 20 V/µs slew rate improves large-signal behavior. Four amplifiers on one monolithic die can implement state-variable, low-pass, high-pass, or notch sections with consistent device characteristics. The design should account for output swing, noise gain, stability with the selected capacitor values, and the 14-pin PDIP lead capacitance. Decoupling capacitors should be placed close to the supply pins, while feedback resistors and capacitors should remain compact to minimize parasitic coupling and phase shifts.
پیشنهادی
Audio Signal Conditioning
AD713KN can condition low-level audio signals in mixer, preamplifier, and balanced-input stages where four amplifier channels reduce board area. The 4 MHz unity-gain bandwidth is ample for many audio-band applications, while the 20 V/µs slew rate permits cleaner handling of larger transients than a very slow precision amplifier. Its specified 0.0003% THD and 2 µV peak-to-peak low-frequency noise support low-distortion signal paths, although system noise also depends on resistor selection and grounding. Use identical feedback networks for channels that need closely matched gain, and keep the unused amplifier section properly biased according to the manufacturer guidance.
پیشنهادی
Industrial Instrumentation
The AD713KN is appropriate for industrial instrumentation requiring several precision voltage-buffer channels in a compact through-hole package. The quad arrangement can condition outputs from sensors, transducers, and laboratory instrumentation while its 4 MHz bandwidth handles higher-frequency components more effectively than a narrow-band precision amplifier. The monolithic die provides close matching of AC and DC characteristics between channels, which is valuable in multichannel measurement systems. Designers should verify the input common-mode range against sensor output levels, calculate offset and drift error at the intended temperature, and provide clean grounding. Add supply bypass capacitance near the package and avoid long, high-impedance traces that can increase noise pickup and settling error.
پیشنهادی
Data Acquisition Front Ends
AD713KN can provide four buffered inputs for a data-acquisition front end, placing a unity-gain or modest-gain buffer between a sensor network and subsequent converter. The 150 V/mV minimum open-loop gain supports accurate voltage-following operation, while the 4 MHz unity-gain bandwidth reduces the likelihood that the amplifier itself becomes the dominant bandwidth limitation in moderate-speed systems. Offset, drift, noise, and input bias current must be included in the total acquisition error budget. Keep sensor returns and amplifier grounds joined at a controlled point, use short feedback loops, and select external resistors with suitable noise and temperature coefficients for high-resolution measurements.
پیشنهادی
Process Control Loops
The four matched amplifier sections in AD713KN can support comparator, current-buffer, error-amplifier, and signal-conditioning functions in process-control equipment. Its 20 V/µs slew rate allows faster response than many precision-only amplifiers, while the close AC and DC matching of monolithic channels is useful when several control or measurement signals are processed similarly. Choose feedback and compensation components carefully to maintain stability, particularly around sensor poles and actuator delays. The amplifier must remain within its input common-mode range and output swing throughout control transients. For repair of older control systems, AD713KNZ provides the clearest documented drop-in route, subject to electrical and lifecycle qualification.
پیشنهادی
Test and Measurement Equipment
AD713KN can serve as a buffer or active element in test and measurement instruments requiring several consistent amplifier channels. The 4 MHz unity-gain bandwidth is useful for moderate-bandwidth measurement paths, and the monolithic quad implementation helps maintain similar response across input or output channels. Its 0.5 mV maximum offset for the AD713K grade makes it relevant to low-level voltage measurements, but the complete error budget must also include bias current, drift, noise, resistor tolerance, and reference accuracy. Place the device away from high-energy switching nodes, use low-leakage protection components where necessary, and validate settling behavior with the complete external network rather than relying only on the amplifier's unity-gain bandwidth.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD713KN — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD713KNZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 14-pin PDIP | 14-pin PDIP |
| Amplifier Configuration | Quad operational amplifier | Quad operational amplifier |
| Internal Amplifier Sections | 4 AD711 BiFET amplifiers | AD713 family quad BiFET amplifier |
| Pin Compatibility | 14-pin PDIP | Pin-to-pin replacement without modification |
تفاوتهای کلیدی
- Four matched BiFET amplifiers on one monolithic die (در مقابلAD713KNZ)
- 4 MHz bandwidth with 20 V/µs slew rate (در مقابلAD713KNZ)
- Low offset and drift for the AD713K grade (در مقابلAD713KNZ)
یادداشتهای طراحی
Place power-supply bypass capacitors close to the AD713KN power pins and connect them to a low-impedance ground plane. Keep each channel's feedback components close to the corresponding amplifier pins to minimize parasitic capacitance in the feedback loop. Route high-impedance input nodes away from outputs, supply-current paths, and switching nodes. For a 14-pin PDIP, follow the manufacturer pin orientation exactly and leave sufficient spacing around adjacent leads to avoid solder bridges during manual rework.
The 4 MHz unity-gain bandwidth makes the AD713KN substantially faster than a conventional precision-only amplifier, so stability must be checked with the actual feedback network and load. Estimate closed-loop response using the noise gain rather than signal gain, and include capacitor tolerances and stray capacitance in the assessment. Add an isolation resistor where capacitive loading could create peaking or oscillation. Validate settling and overshoot with the complete analog section because additional poles outside the amplifier can materially change the result.
Do not treat any 14-pin quad op amp as an automatic replacement for AD713KN. Pin ordering, offset limits, noise, bandwidth, input bias current, common-mode range, and output swing must all be compatible with the original circuit. For AD713KN specifically, use the manufacturer pin-description table when assigning tracks and confirm the exact temperature grade. If the circuit relies on the closely matched channels of the monolithic AD713 die, verify that the proposed replacement provides equivalent channel matching rather than merely identical package dimensions.
اطلاعات انطباق
The component is identified as a commercial-grade 14-pin PDIP operational amplifier. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated and should be confirmed for the exact ordering code and manufacturing lot.