Analog Devices

ADM230LAQ - 5V RS-232 Interface IC | Analog Devices

MPN: ADM230LAQ ✓ Aktif
5 V Vdss 1 A Id 20-CDIP, 0.300 in (7.62 mm) Package
MOQ: 1 |

ADM230LAQ Ringkasan

The Analog Devices ADM230LAQ is a 5 V powered CMOS RS-232 line-driver and receiver interface IC capable of 120 kB/s data transmission. It integrates five driver/receiver channels, onboard DC-DC converters, and a 9 V output swing from a single 5 V supply. The device is packaged in a 20-lead ceramic DIP (CDIP-20) package.

An RS-232 interface IC is a semiconductor bridge between low-voltage digital logic and a physical RS-232 communications port. RS-232 uses single-ended, bipolar signaling that can employ voltage levels beyond the supply rails of ordinary CMOS logic. The ADM230LAQ combines driver channels for transmitting data with receiver channels for detecting incoming signals, allowing a +5 V system to communicate with legacy, industrial, or instrumentation equipment without external ±12 V supplies.

The ADM230LAQ operates from one 5 V supply and includes onboard DC-DC converters that allow the driver output to reach approximately 9 V of swing. Its specified data rate of 120 kB/s supports higher-speed serial links than legacy limited-rate RS-232 implementations. The receiver section supports 1 A input current handling and receiver inputs remain active during shutdown, helping preserve inbound communication when the transmitter side is powered down.

The interface circuitry is designed for EIA-232-E and V.28 implementations. Those standards define the electrical behavior expected of RS-232 drivers, receivers, and signal levels in point-to-point communications. Small 1 F capacitors are used with the onboard converters, allowing the complete interface to be implemented with a single low-voltage supply rather than separate positive and negative power rails.

Typical uses include industrial control equipment, test and measurement systems, point-of-sale terminals, embedded serial ports, and legacy peripheral interfaces. In each case, the five interface channels can support multi-channel RS-232 equipment while the 120 kB/s capability accommodates moderately high-speed command, status, and data traffic.

Designers should preserve the converter capacitor recommendations and route the interface return path as a continuous ground conductor. The ceramic DIP package supports through-hole insertion and thermal conduction, but its operating temperature grade and exact environmental qualifications must be checked against the current manufacturer documentation before deployment.

This page consolidates the confirmed ADM230LAQ interface specifications, package information, application guidance, and clearly qualified replacement considerations. It also distinguishes directly verified functions from parameters that require confirmation in the manufacturer datasheet, helping engineers plan a complete single-supply RS-232 implementation.

Alternatif penggantian untuk ADM230LAQ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian ADM230LAQ (sama faktor bentuk dan footprint) — berbeda di dalam Package, Product Type.

Analog Devices
Package: PDIP-14
Product Type: Dual RS-232 driver and receiver interface IC
Bandingkan dengan ADM230LAQ →

Tidak ada alternatif pengganti yang tersedia untuk produk ini.

Permintaan Alternatif

ADM230LAQ Spesifikasi

Product Type 5 V powered CMOS RS-232 drivers/receivers
Tegangan Pemuat 5 V
Number of Channels 5 channels
Maximum Data Rate 120 kB/s
Driver Output Swing 9 V
Receiver Input Current 1 A
Receiver Input Voltage 30 V
Converter Capacitor 1 F
Shutdown Feature Low-power shutdown with receivers active
Onboard Converter DC-DC converter
RS-232 Compliance EIA-232-E and V.28
Logic Family CMOS
Paket 20-CDIP, 0.300 in (7.62 mm)
Tipe Mounting Through-hole
Number of Terminals 20 terminals

ADM230LAQ 20-cdip, 0.300 in (7.62 mm) Diamant Konfigurasi Panduan

Konfigurasi pin untuk ADM230LAQ (20-cdip, 0.300 in (7.62 mm) pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 20-cdip, 0.300 in (7.62 mm) untuk ADM230LAQ

Tidak ada data diatribut pin yang tersedia untuk ADM230LAQ.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

ADM230LAQ cocok untuk 6 aplikasis: Industrial Control Terminals, Test and Measurement Equipment, Point-of-Sale and Retail Equipment, Legacy Computer Serial Ports, Instrument Communication Interfaces, Embedded Data Acquisition Systems.

🏭

Industrial Control Terminals

The ADM230LAQ fits industrial control terminals that need several RS-232 ports but only have a 5 V power rail. Its five driver/receiver channels can connect controllers, indicators, scales, and configuration tools without requiring separate positive and negative RS-232 supplies. Operation at up to 120 kB/s supports responsive status polling and moderate command traffic, while the onboard DC-DC converters deliver approximately 9 V of driver swing. The 20-CDIP format also suits equipment assembled with through-hole processes. Design the converter-capacitor layout exactly as directed by the manufacturer and maintain a continuous signal-ground path between the terminal and connected equipment.

🔧

Test and Measurement Equipment

The ADM230LAQ is useful in test and measurement instruments that retain RS-232 for instrument control, calibration, or legacy peripheral connectivity. The single 5 V supply simplifies front-panel and embedded instrument designs, and the 120 kB/s data rate is suitable for command exchange and moderate measurement transfers. Five channels allow one instrument to manage several RS-232 links without allocating a separate transceiver to every port. EIA-232-E and V.28 compatibility supports conventional control-system interoperability. Keep converter capacitors near their assigned pins and isolate interface traces from sensitive measurement circuitry to avoid coupling command activity into high-impedance analog nodes.

🖥️

Point-of-Sale and Retail Equipment

Retail peripherals such as scales, receipt printers, customer displays, and barcode equipment can use the ADM230LAQ for RS-232 connectivity in a 5 V embedded controller. The five-channel arrangement supports several peripherals from one interface device, and the 120 kB/s rate accommodates ordinary transaction and status traffic. Because many countertop systems have limited supply rails, onboard DC-DC conversion and a single 5 V input simplify system integration. The 20-CDIP package is appropriate for products assembled on through-hole boards. Use the manufacturer capacitor and grounding layout to preserve signal integrity, particularly when cables from printers or scales are physically distant from the logic board.

🖥️

Legacy Computer Serial Ports

The ADM230LAQ provides a practical bridge between modern +5 V logic and legacy RS-232 ports found on industrial computers, service equipment, and specialized peripherals. Its five channels allow one IC to service several serial connectors, while the approximately 9 V driver swing and EIA-232-E and V.28 behavior maintain compatibility with conventional RS-232 voltage expectations. A 120 kB/s ceiling supports faster legacy transfers than many basic RS-232 implementations. During shutdown, the receiver channels remain active, allowing inbound status or control signals to persist when the transmitter side is disabled. Validate grounding and cable routing to avoid ground-offset errors at the connected port.

📡

Instrument Communication Interfaces

The ADM230LAQ is appropriate for instruments that expose RS-232 command ports to laboratory computers or embedded controllers. The 5 V supply requirement is convenient for compact instruments, while the 120 kB/s data rate supports responsive command polling, configuration uploads, and status reads. Multiple receiver and driver channels can be allocated to separate instruments, provided the design follows the manufacturer’s per-channel loading and shutdown guidance. The receiver input rating of 30 V offers substantial withstand margin, but it should not be interpreted as permission for continuous operation outside the specified input range. Use a controlled ground reference and place the 1 F converter capacitors as directed.

📺

Embedded Data Acquisition Systems

The ADM230LAQ can connect legacy sensors, programmable instruments, and laboratory modules to a +5 V embedded controller. Its five channels support several RS-232 devices in one acquisition chassis, and the 120 kB/s rate accommodates periodic measurements and command traffic where sustained high-speed streaming is not required. The onboard converters eliminate a separate bipolar RS-232 supply, helping reduce board complexity in space-constrained systems. The through-hole CDIP package may simplify ruggedized control boards and prototype assembly. Separate converter and switching circuitry from sensitive acquisition inputs, use the specified 1 F capacitors, and provide a low-impedance ground return to minimize errors at the connected equipment.

What is the ADM230LAQ?
The ADM230LAQ is a five-channel, 5 V powered CMOS RS-232 line-driver and receiver interface from Analog Devices. It supports data rates up to 120 kB/s and includes onboard DC-DC converters that provide a 9 V driver output swing from one 5 V supply. The device is offered in a 20-lead ceramic DIP package. Analog Devices describes it as an EIA-232-E and V.28-compatible interface.
What are the key specifications of ADM230LAQ that engineers should know?
The principal ADM230LAQ specifications are a single 5 V supply, five RS-232 channels, 120 kB/s maximum data rate, 9 V driver output swing, 1 A receiver input capability, and 30 V receiver input rating. Its converter circuit uses small 1 F capacitors, and receiver channels remain active during shutdown. The physical device uses a through-hole 20-CDIP package measuring 0.300 in (7.62 mm) across the package row.
Does the ADM230LAQ need a ±12 V power supply?
No, the ADM230LAQ operates from a single 5 V supply rather than requiring separate positive and negative RS-232 rails. Onboard DC-DC converters generate the elevated driver voltage required to obtain approximately 9 V of output swing. This makes the interface suitable for systems in which only a 5 V power rail is available, although the manufacturer still requires the specified converter capacitors and layout.
What is the maximum data rate of ADM230LAQ?
The ADM230LAQ supports a maximum data rate of 120 kB/s. This rating applies to the five-channel RS-232 driver and receiver interface when operated within the manufacturer’s specified supply, capacitance, loading, and wiring conditions. For a new design, use the data-sheet timing and loading characteristics to confirm the required slew rate, cable length, and termination arrangement rather than treating the headline rate as independent of the channel conditions.
Where can I download the ADM230LAQ datasheet PDF?
The ADM230LAQ datasheet PDF is available through the Analog Devices documentation identified by the verified data-sheet link on this page, and a manufacturer-document mirror is also accessible through the listed data source. The documentation describes the +5 V powered CMOS RS-232 drivers and receivers, EIA-232-E and V.28 compliance, 120 kB/s operation, converter circuitry, and shutdown behavior. Use the manufacturer document for final pin, electrical, and application details.
Where is the ADM230LAQ pinout located?
The ADM230LAQ pinout is located in the pin-description table and package drawing of the manufacturer datasheet. The verified product information confirms a 20-lead ceramic DIP with through-hole mounting, but it does not reproduce individual pin numbers or signal names. Therefore, no pin assignments are asserted on this page. Before wiring the device, map every driver, receiver, supply, ground, enable, and converter-capacitor connection directly from the datasheet.
Is the ADM230LAQ suitable for industrial RS-232 equipment?
The ADM230LAQ is suitable for many industrial RS-232 interfaces because it provides five channels, 120 kB/s operation, EIA-232-E and V.28 compatibility, and a single 5 V supply. Its 30 V receiver input rating also provides useful margin for connected equipment. Industrial suitability should still be confirmed against the device’s exact operating-temperature range and environmental qualification, because those details must be taken from the manufacturer documentation.
What can replace the ADM230LAQ?
The ADM230L family includes closely related devices, but a valid replacement must match the ADM230LAQ’s electrical ratings, shutdown behavior, 20-lead package, pin arrangement, and temperature grade. ADM230LAN and ADM230LJN appear in cross-reference results, but their package and full pin compatibility were not confirmed by the available technical data. Treat them as review candidates rather than drop-in replacements until the manufacturer pinouts and ordering information establish an exact match.
Is ADM230LAQ the same as ADM230LAN?
No exact equivalence can be concluded from the available information. Both devices belong to the ADM230L interface family and are presented in a direct comparison, but the verified material does not establish that ADM230LAN uses the same 20-lead ceramic DIP package, pinout, temperature grade, and shutdown implementation. Check the package suffix and datasheet before substitution. A shared family name alone does not establish drop-in compatibility.
What is the best Analog Devices equivalent for ADM230LAQ?
The closest confirmed family candidates are ADM230LAN and ADM230LJN, both identified in RS-232 cross-reference material. However, the exact Analog Devices equivalent depends on whether the replacement must preserve ceramic-DIP construction, industrial temperature coverage, converter pinout, receiver shutdown behavior, and lead spacing. Do not approve either candidate as a drop-in replacement until its package drawing and pin-description table have been compared with the ADM230LAQ.
When should I choose ADM230LAQ over another RS-232 interface?
Choose the ADM230LAQ when a design needs five RS-232 channels, a single 5 V supply, operation up to 120 kB/s, and a 20-lead ceramic DIP implementation. It is particularly suitable where a through-hole industrial or legacy interface is preferred and where external positive and negative RS-232 rails are undesirable. Select another interface if a surface-mount package, different channel count, isolated bus, lower data rate, or modern alternate protocol better matches the system.
Is ADM230LAQ suitable for a five-port RS-232 controller?
The ADM230LAQ can support a five-channel RS-232 interface because it contains five driver/receiver functions and operates from one 5 V supply. Its 120 kB/s capability is suitable for command, status, and moderate data transfers across multiple ports. Confirm that all five channels are used according to the datasheet, provide the required converter capacitors, and route each interface signal with an appropriate ground reference to minimize noise and data errors.
Why does ADM230LAQ use onboard DC-DC converters?
The ADM230LAQ uses onboard DC-DC converters so its RS-232 drivers can generate approximately 9 V of output swing from a single 5 V supply. Standard RS-232 signals are bipolar, while many embedded systems provide only low-voltage positive rails. The converters therefore bridge the voltage-domain difference internally, reducing system power-supply complexity while retaining the signal swing needed for compliant EIA-232-E and V.28 operation.
Where can I buy ADM230LAQ online and check its price?
Use the Request a Quote form on this page to request ADM230LAQ availability, current pricing, lot size, and lead time. The page intentionally does not publish a static price because transaction terms and inventory change. When requesting a quotation, specify the required quantity, 20-CDIP package acceptance, operating-temperature needs, and whether RoHS or other compliance documentation is required.
Is ADM230LAQ in stock and what is its lead time?
Current stock and a fixed lead time are not established by the available product documentation, so request a quote on this page for the latest allocation and delivery information. Provide the quantity, target date, approved sourcing status, and packaging requirements. Do not infer availability from an older catalog entry, because stock for legacy RS-232 interface devices can change independently of the manufacturer’s lifecycle status.
How should a PCB layout implement the ADM230LAQ converter capacitors?
Place the specified 1 F converter capacitors close to their designated ADM230LAQ pins and follow the manufacturer’s reference layout for trace length and return paths. Keep the RS-232 driver and receiver routes away from sensitive analog or high-speed digital traces, and provide a continuous ground return to the connected equipment. Because the verified material does not include the complete pin table or layout drawing, the final implementation should be checked against the datasheet before release.

Data referensi engineering untuk ADM230LAQ — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the ADM230LAQ when a system needs five RS-232 channels, operation from a single 5 V supply, data rates up to 120 kB/s, and a through-hole 20-lead ceramic DIP package. Its onboard DC-DC converters produce approximately 9 V of driver swing, reducing the need for external positive and negative RS-232 rails. The receiver channels remain active during shutdown, which is useful when inbound status must survive transmitter shutdown. However, the ADM230LAQ is not a universal pin-compatible substitute for every ADM230L suffix. ADM230LAN and ADM230LJN are family-review candidates, but their package and pin compatibility were not confirmed. Select them only after comparing the manufacturer package drawings and pin tables. For designs requiring surface-mount packaging, fewer channels, isolation, or a different communications protocol, choose a different qualified interface rather than modifying this through-hole layout.

Catatan Desain

Place the required 1 F converter capacitors at the locations assigned by the manufacturer datasheet and keep their associated traces short. The available information confirms the capacitor value and single-supply converter function but does not reproduce the pinout, so the final placement must be checked against the device drawing. Avoid routing converter-current paths across sensitive receiver or measurement signals, and provide a continuous ground plane beneath the interface area where the package and board construction permit.

Keep RS-232 driver and receiver traces away from clocks, switching-regulator nodes, and high-impedance analog inputs. Maintain a continuous signal-ground return to the connected equipment because RS-232 is a single-ended interface and ground potential differences can appear as data errors. If the ADM230LAQ sits near a cable connector, place transient-protection structures at the connector boundary and use the receiver’s 30 V input rating as protection margin rather than as a substitute for a correctly selected protection network.

Do not substitute an ADM230 family member solely because its product description mentions EIA-232-E or V.28 compatibility. Verify the package suffix, pin names, pin numbers, converter implementation, shutdown behavior, temperature grade, and lead dimensions before approving a replacement. Also avoid assuming that receiver operation during shutdown makes every channel suitable for live use; follow the datasheet limits for signal amplitude, loading, and data state.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for ADM230LAQ. The industrial temperature classification shown by a distributor listing does not by itself constitute AEC-Q100 qualification.

Data disahkan pada: 2026-11-09 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

ADM230LAQ datasheet ADM230LAQ datasheet pdf ADM230LAQ pinout ADM230LAQ specifications ADM230LAQ 20 CDIP Analog Devices ADM230LAQ ADM230LAQ RS-232 interface ADM230LAQ 120 kB/s ADM230LAQ equivalent ADM230LAQ replacement ADM230LAQ vs ADM230LAN ADM230LAQ price ADM230LAQ stock ADM230LAQ industrial interface ADM230LAQ single 5 V supply

Komponen dan Istilah Terkait

Analog Devices ADM230LAQ ADM230LAN ADM230LJN RS-232 EIA-232-E V.28 CMOS line driver line receiver interface IC serial communications IC semiconductor DC-DC converter single 5 V supply 120 kB/s 9 V output swing 30 V receiver input 1 A receiver input 1 F capacitor low-power shutdown 20-CDIP through-hole package industrial control equipment
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ