ADS7800JU - 12-Bit 3us SAR ADC | Texas Instruments | Precision
MPN: ADS7800JU ✓ AktifADS7800JU Ringkasan
An ADC is an integrated circuit that converts a continuous analog voltage into a numeric code. The ADS7800 belongs to the sampling ADC and successive-approximation hierarchy, commonly abbreviated SAR ADC. A SAR ADC compares the sampled input with an internally generated reference through a successive conversion process, producing a 12-bit result after approximately 3 us. This architecture combines relatively high conversion speed with useful resolution for industrial measurement, instrumentation, and control systems.
Key features include one analog input, 12-bit resolution, a 3 us conversion time, and a maximum sampling rate of 333 kSPS. The ADS7800JU is offered in the 24-pin SOIC (DW) package and is specified over -40 C to +85 C. Two device grades are described by Texas Instruments as offering different linearity and dynamic performance, allowing the application requirements to determine the appropriate grade. A parallel interface provides direct access to the converted digital value.
The ADC operates from a +5 V supply and either a -12 V or -15 V supply. These rails provide suitable operating conditions for bipolar analog input stages while the internal conversion process generates the digital result. Because the converter includes a complete sampling architecture, it reduces the need for separate sampling-hold circuitry while still requiring careful attention to input drive, reference stability, grounding, and digital-bus timing.
Typical applications include industrial process monitoring, laboratory instrumentation, sensor-interface circuits, closed-loop control, data acquisition, and embedded measurement systems. A system designer should select an input-conditioning network that keeps the analog signal within the converter's input range and provide a low-noise reference if measurement accuracy is important. The parallel output bus should be connected only to compatible logic, with suitable bus timing and unused inputs handled according to the manufacturer data sheet.
A key design consideration is the relationship between input bandwidth, acquisition time, and conversion rate. The 333 kSPS maximum rate is useful for continuous monitoring, but high-rate operation requires a low-impedance source and correct settling of the sampling network. The negative supply must be generated cleanly when the selected analog input range requires bipolar operation, and the +5 V rail should be decoupled close to the device.
This product page combines the manufacturer's core electrical, package, application, and lifecycle information with structured alternatives, application guidance, comparison data, and practical PCB-design notes. These resources help engineers identify whether the ADS7800JU fits a new design or whether a closely related ADC should be evaluated before layout begins.
Alternatif penggantian untuk ADS7800JU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ADS7800JU (sama faktor bentuk dan footprint) — berbeda di dalam Conversion Time, Package, Mounting Type, Resolution, Sampling Rate.
ADS7809UB
✅ Drop-InKontak untuk harga
Lihat Datasheet →AD7864
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MCP3204-CI/P
✅ Drop-InKontak untuk harga
Lihat Datasheet →MAX1241BCSA+T
✅ Drop-InKontak untuk harga
Lihat Datasheet →ADS7800JU Rating Maksimal & Karakteristik Listrik
| ADC Type | Successive-approximation sampling ADC |
| Resolusi | 12 bit |
| Number of Inputs | 1 input |
| Conversion Time | 3 us |
| Maximum Sampling Rate | 333 kSPS |
| Output Interface | Parallel |
| Positive Supply Voltage | +5 V |
| Negative Supply Voltage | -12 V or -15 V |
| Paket | 24-pin SOIC (DW) |
| Rentang Suhu Kerja | -40 C to +85 C |
| Available Commercial Temperature Range | 0 C to +70 C |
| Linearity and Dynamic Performance Grades | 2 grades |
| Tipe Mounting | Surface mount |
ADS7800JU 24-pin soic (dw) Diamant Konfigurasi Panduan
Konfigurasi pin untuk ADS7800JU (24-pin soic (dw) pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk ADS7800JU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ADS7800JU cocok untuk 6 aplikasis: Industrial Process Monitoring, Precision Data Acquisition, Laboratory Instrumentation, Closed-Loop Control, Sensor Interface Circuits, Embedded Measurement Systems.
Industrial Process Monitoring
The Texas Instruments ADS7800JU fits process-monitoring designs that require a 12-bit measurement updated at up to 333 kSPS. Its single input and 3 us conversion time support fast sensing of pressure, position, level, or temperature signals after suitable conditioning. The 24-pin SOIC package permits a conventional surface-mount layout, while the parallel output can connect to a processor or programmable logic. Engineers should scale the sensor output into the converter input range, provide a stable reference and clean supply rails, and verify acquisition timing against the source impedance.
Precision Data Acquisition
The ADS7800JU is appropriate for compact 12-bit acquisition systems that need deterministic conversion timing without a multiplexing stage. A conversion time of 3 us and a maximum sampling rate of 333 kSPS allow rapid capture of a conditioned analog waveform. Its 24-pin parallel interface exposes the result directly to digital logic, reducing conversion-interface complexity. For best performance, use a low-impedance drive network, separate analog and digital return paths, and validate the input's settling behavior at the highest operating sample rate.
Laboratory Instrumentation
In laboratory instruments, the ADS7800JU can digitize a conditioned measurement channel while providing 12-bit resolution and a 3 us conversion time. This combination is useful for front ends that sample slowly varying sensor signals or repetitive waveform segments. The parallel interface can feed a control FPGA or microcontroller without requiring a serial ADC. Calibration performance will depend on the reference network, analog front-end linearity, noise, grounding, and the specified input range, so those details should be established from the manufacturer data sheet during design.
Closed-Loop Control
The ADS7800JU can serve as the measurement element in a closed-loop motion or equipment-control system. A 3 us conversion time allows the controller to receive a new 12-bit measurement rapidly, while the one-input architecture keeps the design focused on a primary feedback channel. The converter requires +5 V and either -12 V or -15 V supplies, which makes rail planning important in compact embedded systems. Validate control-loop latency, output update behavior, analog noise, and fault-state handling before using the ADC in a safety-critical path.
Sensor Interface Circuits
The ADS7800JU is suitable for digitizing outputs from bridge, resistive, and active sensor front ends when the conditioned signal can be handled by a 12-bit, single-input SAR converter. Its 333 kSPS maximum rate is more than adequate for many temperature, pressure, and position sensors, while the 3 us conversion time supports higher-rate feedback. The analog conditioning network should include gain, filtering, and any required level shifting. Check input settling, reference accuracy, and supply requirements in the data sheet to ensure the complete signal chain does not exceed the converter's accuracy target.
Embedded Measurement Systems
The 24-pin SOIC ADS7800JU works well in embedded measurement equipment where a parallel ADC simplifies connection between analog conditioning and digital control logic. Texas Instruments specifies the JU grade over -40 C to +85 C, supporting industrial-temperature designs when the complete system also meets its environmental requirements. The +5 V, -12 V, and -15 V operating options provide flexibility in dual-supply analog architectures. Designers should reserve routing space for the parallel bus, keep converter traces away from sensitive analog inputs, and use local bypass capacitors according to the recommended application circuit.
Data referensi engineering untuk ADS7800JU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ADS7809UB | AD7864 | MCP3204 | MAX1241 |
|---|---|---|---|---|---|
| Package | 24-pin SOIC (DW) | 24-pin SOIC (DW) | 24-pin SOIC | 24-pin SOIC | 24-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Microchip Technology | Maxim Integrated |
Diferensiator Kunci
- Single-input converter with a defined 3 us conversion time (vsMCP3204)
- Family choice of linearity and dynamic-performance grades (vsAD7864)
- Single-supplier continuity with a related Texas Instruments ADC (vsMAX1241)
Catatan Desain
Place the input-conditioning components, local supply bypass capacitors, and converter as close together as practical. Keep sensitive analog traces short and route the 12-bit parallel output away from the analog input and reference network. Use a single ground strategy that keeps analog return currents from crossing the digital output current path; the manufacturer application circuit should guide the final reference layout.
Validate the source impedance and acquisition network against the 3 us conversion specification. A high-impedance sensor or slow-settling filter can cause conversion error even when the digital timing is correct. Measure the input at the ADC pin with appropriate test equipment, and adjust the source drive or acquisition time before increasing the sample rate beyond 333 kSPS.
Design the supply network for +5 V together with either -12 V or -15 V. Decouple each supply close to the device and use stable, low-noise sources for the analog rails and reference circuitry. Because the available data does not state the exact input range, reference voltage, or power dissipation, use the manufacturer data sheet to confirm that the selected bipolar rails and signal amplitudes remain within the operating limits.
Informasi Konformitas
The manufacturer product page identifies the ADS7800JU temperature range, supply requirements, and package, but the retrieved information does not state specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals results. AEC-Q100 status is marked not applicable because the device is not identified as an automotive-qualified product.