ATTINY261A-XU - 20MHz AVR MCU with 2KB Flash | Microchip
MPN: ATTINY261A-XU ✓ AktifATTINY261A-XU Ringkasan
A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, data memory, I/O ports, timers, and communication peripherals on one device. The ATTINY261A belongs to the ATtiny family, which sits within the broader hierarchy of AVR microcontrollers, embedded processors, and semiconductor control devices. Its small memory footprint is intended for compact embedded-control tasks rather than general-purpose computing.
The ATTINY261A combines 32 general-purpose working registers, an 8-bit timer/counter with compare modes, USI connectivity, and brown-out detection with power-on reset. The 2 KB flash capacity supports a bootloader or a focused control routine, while the 128 B SRAM and 128 B EEPROM provide working data and retained parameter storage. The 16 I/O pins can be assigned to digital inputs, outputs, and interrupt-capable functions according to the device pin configuration.
Microchip describes the ATTINY261A as a picoPower 8-bit AVR RISC-based device. Its reduced operating voltage range and low-power design are useful in compact consumer products, industrial controls, sensor nodes, and accessories where board area and energy use matter. The 20-pin TSSOP is surface mount and can be placed on automated production assemblies rather than through-hole breadboards.
Typical applications include simple motor or valve controllers, LED status indicators, keypads, battery-powered sensors, communication bridges, and compact embedded modules. In each case, the firmware must fit within 2 KB of flash, while the application should avoid relying on large buffers or storage-intensive libraries.
Design the decoupling network and programming connections according to the manufacturer datasheet. Keep the reset path stable, route sensitive communication lines away from switching edges, and confirm that the selected clock and peripheral configuration remain within the device electrical limits. Software should use the chip’s documented timer and USI resources rather than adding unnecessary external components.
This product page combines the exact ATTINY261A-XU electrical identity, verified package and memory details, migration context, direct-replacement information, and practical selection guidance to support PCB, firmware, and sourcing decisions.
Alternatif penggantian untuk ATTINY261A-XU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
ATTINY261-20SU
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ATTINY261A-XU Rating Maksimal & Karakteristik Listrik
| Product Type | 8-bit AVR RISC microcontroller |
| Maximum CPU Frequency | 20 MHz |
| Flash Memory | 2 KB (1K x 16) |
| EEPROM Memory | 128 B |
| SRAM | 128 B |
| General-Purpose I/O Lines | 16 |
| General-Purpose Working Registers | 32 |
| Timer/Counter | 8-bit with compare modes |
| Connectivity | USI |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Nominal Supply Options | 2.5 V, 3.3 V, and 5 V |
| Paket | 20-pin TSSOP |
| Tipe Mounting | Surface mount |
| Industrial Temperature Grade | Yes |
| Status RoHS | Compliant |
| Jumlah Pin | 20 pins |
ATTINY261A-XU 20-pin tssop Diamant Konfigurasi Panduan
Konfigurasi pin untuk ATTINY261A-XU (20-pin tssop pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk ATTINY261A-XU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ATTINY261A-XU cocok untuk 6 aplikasis: Battery-Powered Sensor Node, LED Status and Sequencer Controller, Motor and Valve Control, USI Serial Communication Bridge, Industrial Keypad and Panel Interface, Consumer Accessory Controller.
Battery-Powered Sensor Node
The ATTINY261A-XU fits a compact battery-powered sensor node because it combines a 20 MHz AVR core with a 1.8 V to 5.5 V operating range and only 16 I/O pins. The 2 KB flash limit suits compact acquisition and threshold-control routines rather than data logging or protocol-heavy firmware. Use the device to wake periodically, read a compatible sensor, apply filtering, and transmit a compact result. Its picoPower architecture helps support low-power operation, while brown-out detection and power-on reset protect operation near the lower supply limit. The engineer should budget the application against the device’s 128 B SRAM and 128 B EEPROM, keeping transient buffers and retained configuration within those constraints.
Direkomendasikan
LED Status and Sequencer Controller
The ATTINY261A-XU is suitable for LED sequencing, status indication, and simple lighting effects because its 16 general-purpose I/O lines provide ample digital outputs for compact panels. The 20 MHz AVR core provides ample timing headroom for debouncing, fades, blink patterns, and fault indicators without requiring a high-end processor. Firmware can use the 8-bit timer/counter with compare modes to create deterministic intervals, leaving the remaining I/O available for switches or interlocks. Because the device offers 2 KB of flash, the application should use compact lookup tables and avoid large animation libraries. A current-limiting resistor or regulated LED driver remains necessary for each channel, and the PCB should keep high-current switching paths separated from sensitive control traces.
Direkomendasikan
Motor and Valve Control
The ATTINY261A-XU can serve as the logic controller for a small motor, solenoid, or valve when the design uses digital command signals rather than a high-power analog drive stage. Its 16 I/O pins allow control inputs, limit-state detection, and gate-control outputs, while the 8-bit timer/counter supports basic timing or pulse-width functions. The 20 MHz processing rate is adequate for deterministic supervisory logic and safety interlocks. Because the ATTINY261A-XU is not a high-current driver, an appropriately rated transistor, MOSFET, or driver stage must handle the load. Firmware should include startup and overtravel checks, and the layout should keep inductive transients and motor current paths away from the controller and its clock circuitry.
Direkomendasikan
USI Serial Communication Bridge
The ATTINY261A-XU fits a small USI-based communication bridge because the MCU includes USI connectivity alongside an 8-bit AVR core and 16 I/O lines. It can translate between simple serial wiring and a higher-level product function when both sides use compatible electrical levels and protocol timing. The 20 MHz clock supports straightforward bit-banged or peripheral-assisted communication routines, while 128 B of SRAM constrains simultaneous buffering and protocol state. Firmware designers should select a protocol and framing strategy that fit 2 KB of flash, and the board should provide the required level translation and signal conditioning. Keep the USI route short, provide the documented pull resistors, and isolate slow-changing external signals from the oscillator and programming connections.
Direkomendasikan
Industrial Keypad and Panel Interface
The ATTINY261A-XU is appropriate for a compact keypad, control panel, or front-panel interface because 16 I/O lines can support multiple keys, indicators, and interlocks while the 20 MHz AVR core handles debouncing and menu logic. Its 128 B EEPROM can retain calibration values, panel configuration, or user preferences, and the 2 KB flash supports a focused state machine. The surface-mount TSSOP package is suitable for compact production assemblies and automated testing. A practical design should debounce contacts in firmware, define safe behavior for invalid or simultaneous inputs, and use the power-on-reset and brown-out features to establish a known startup state. The panel layout should maintain clean ground return paths and separate switch wiring from sensitive timing or communication traces.
Direkomendasikan
Consumer Accessory Controller
The ATTINY261A-XU works well in a small consumer accessory that coordinates buttons, indicators, a simple sensor, and a low-speed serial link. Its 20-pin TSSOP footprint reduces board area, while the 1.8 V to 5.5 V supply range allows use with common regulated rails and compatible battery systems. The 2 KB flash and 128 B SRAM are adequate when the accessory performs a narrow, well-defined function rather than running a graphical interface or complex connectivity stack. Firmware can use EEPROM for small persistent settings and the timer/counter for blinking or periodic tasks. The product should define safe pin states during reset and power loss, and the implementation should validate every actuator state before enabling it to avoid unintended motion, illumination, or audible output.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ATTINY261A-XU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ATTINY261-20SU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-pin TSSOP | 20-pin TSSOP |
| CPU Architecture | 8-bit AVR RISC | 8-bit AVR RISC |
| Flash Memory | 2 KB | 2 KB |
Diferensiator Kunci
- Compact memory footprint (vsATTINY861A-XUR)
- 20 MHz performance in a small package (vsATTINY861V-10SU)
- Documented migration path from the earlier generation (vsATTINY261-20SU)
Catatan Desain
Confirm the complete power budget at the device pins before finalizing the rail. The ATTINY261A-XU supports a 1.8 V to 5.5 V range, but the usable current depends on clock speed, active peripherals, I/O loading, and operating mode. Place the manufacturer-recommended bypass capacitors close to the supply and ground pins, keep return-current paths short, and size the upstream regulator for peak—not merely average—load.
Follow the ATtiny261A 20-pin TSSOP land pattern and pin-description table when assigning nets. Keep the programming interface accessible for production programming and leave perimeter clearance for the device body and leads. Route clock-capable and communication signals away from switching nodes and noisy power wiring. A compact ground plane beneath the device can improve return-path continuity, but follow the exact package drawing rather than estimating pad geometry.
Do not design around the memory limits of ATTINY261A-XU as though it were a larger ATtiny device. Its 2 KB flash, 128 B SRAM, and 128 B EEPROM constrain code size, buffers, and retained configuration. Test startup behavior after reset, validate all external inputs before driving actuators, and account for brown-out conditions near the minimum supply voltage. When migrating from ATTINY261, review electrical-characteristic differences caused by the changed manufacturing process.
Keep sensitive analog or communication front ends away from switching-power loops and relay or motor transients. Provide a direct, low-impedance return from decoupling capacitors to the ground pins. For USI-based interfaces, minimize trace length and use only the bias or termination values specified by the interface design. The 20 MHz clock capability should not be treated as a requirement; using a lower permitted clock can reduce switching activity when the application timing permits it.
Informasi Konformitas
The ATTINY261A-XU comparison record identifies the device as RoHS compliant. The industrial-temperature designation does not by itself establish AEC-Q100 qualification.