BLE113-A-M256K - Bluetooth 4.0 BLE Module 256K Flash | Silicon Labs
MPN: BLE113-A-M256K ✓ AktifBLE113-A-M256K Ringkasan
A Bluetooth Low Energy (BLE) module is a complete wireless subsystem within the broader hierarchy of RF transceiver modules and short-range wireless communication devices. Whereas a bare radio chip requires the designer to integrate a microcontroller, antenna matching network, and protocol stack, a BLE module such as the BLE113 integrates all features required for a Bluetooth smart application: the Bluetooth radio, antenna, MCU, and certified stack, reducing time to market and RF design risk.
Key features include the 256 KB flash variant (versus 128 KB on BLE113-A-V1), which is significant for over-the-air (OTA) firmware updates and extensive BGScript applications, integrated chip antenna eliminating external RF matching design, and low power operation targeted at small sensors and accessories. Serial interfaces include ISP, PWM, SPI, and UART, allowing flexible host connectivity or fully standalone operation via BGSCRIPT.
Technically, the module is built around the Texas Instruments CC2541 utilized IC and belongs to the Bluegiga BLE113 family acquired by Silicon Labs. The -93 dBm sensitivity supports reliable connections at Class 2 power levels on the 2.4 GHz ISM band, and the integrated antenna means the RF performance is pre-certified, saving regulatory test cost.
Typical applications include low-power sensors and accessories, battery-powered health and fitness devices, beacons, smart home endpoints, and industrial wireless sensor nodes where a compact, certified BLE link is required.
A key design consideration is supply voltage: the module accepts only 2.0 V to 3.6 V, so a single CR2032 coin cell or a regulated LiPo rail works well, but 5 V systems require an LDO. Allow antenna keep-out clearance on the PCB around the chip antenna region.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternatif penggantian untuk BLE113-A-M256K — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian BLE113-A-M256K (sama faktor bentuk dan footprint) — berbeda di dalam Flash Memory, Serial Interfaces, Mounting Type, Frequency Band, Supply Voltage Range.
BLE113-A-V1
✅ Drop-InKontak untuk harga
Lihat Datasheet →BLE113-A-M256K-MT4
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
BLE121LR-A-M256K
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
BLE112-A-V1
✅ Drop-InKontak untuk harga
Lihat Datasheet →BLE113-A-M256K Spesifikasi (diterbitkan produsen)
| Wireless Standard | Bluetooth v4.0 (Bluetooth Smart / BLE) |
| Frequency Band | 2.4 GHz ISM |
| Flash Memory | 256 KB |
| Supply Voltage Range | 2.0 V to 3.6 V |
| Laju Data | 2 Mbps |
| Receiver Sensitivity | -93 dBm |
| Antenna Type | Integrated chip antenna |
| Transmit Power Class | Class 2 (802.15.1) |
| Utilized IC | CC2541 |
| Serial Interfaces | ISP, PWM, SPI, UART |
| Tipe Mounting | Surface Mount |
| Package Type | Bluetooth module, castellated SMD pads |
| Mounting Category | Integrated, Chip antenna |
| Series | BLE113 |
| Status RoHS | RoHS compliant |
| Application Target | Small and low power sensors and accessories |
BLE113-A-M256K Antarmuka & Konnektor
BLE113-A-M256K mengekspose antarmuka dan konnektor berikut seperti dipublikasikan oleh produsen: Nirkabel, Masukan Kuasa. Pada dokumentasi produsen, definisi untuk penomoran pin ekspansi, nomor pin konnektor, dan batasan elektrik.
| Nirkabel | Bluetooth v4.0 (Bluetooth Smart / BLE) |
| Masukan Kuasa | 2.0 V to 3.6 V |
Lihat ke: dokumentasi produsen untuk tampilan penuh header pinout dan nomor pin penghubung.
Karakteristik Kuasa & Thermal
| Kuasa Masuk | 2.0 V to 3.6 V |
Parameter kuasa masuk dan thermal untuk BLE113-A-M256K seperti dipublikasikan oleh produsen.
Aplikasi Umum
BLE113-A-M256K cocok untuk 6 aplikasis: Battery-Powered BLE Sensors, Fitness and Health Accessories, Smart Home and IoT Endpoints, iBeacon and Eddystone Beacons, Industrial Wireless Sensor Nodes, Smartphone-Connected Consumer Devices.
Battery-Powered BLE Sensors
The BLE113-A-M256K was purpose-built for small and low power sensors and accessories, making it the default choice for coin-cell sensor nodes. Its 2.0 V to 3.6 V supply accepts a CR2032 directly without a regulator, and Bluetooth Low Energy connection intervals let the module sleep at microamp average current between events. The 256 KB flash leaves room for sensor calibration tables, a full BGScript application, and an OTA update image simultaneously. In a typical temperature or humidity sensor node, the module connects via its SPI, UART, or PWM interfaces to the sensor IC and reports over BLE GATT characteristics at -93 dBm sensitivity, giving reliable whole-home coverage from the integrated chip antenna with zero external RF components.
Direkomendasikan
Fitness and Health Accessories
Wearable health and fitness products such as heart-rate straps, activity trackers, and thermometers benefit directly from the BLE113-A-M256K integration level: radio, MCU, certified Bluetooth 4.0 stack, and chip antenna in one castellated surface-mount module, shrinking the wireless BOM to a single part. The 2 Mbps over-the-air rate handles streaming sensor data to smartphone apps, while the standard GATT profiles used by the Silicon Labs stack ensure interoperability with iOS and Android devices. Because regulatory certification of the radio is already completed at module level, accessory makers avoid costly RF requalification. The 256 KB flash supports OTA firmware updates, a practical necessity for consumer wearables that receive feature updates in the field.
Direkomendasikan
Smart Home and IoT Endpoints
Smart home endpoints such as door/window sensors, smart plugs, lighting controls, and BLE-to-cloud bridges use the BLE113-A-M256K as a certified 2.4 GHz Bluetooth Smart link. The UART and SPI interfaces connect cleanly to any host MCU, or BGScript eliminates the host MCU entirely for simple devices, cutting BOM cost. The -93 dBm receiver sensitivity and integrated chip antenna deliver Class 2 range suitable for room-to-room coverage, and the 2.0 V to 3.6 V supply works from mains-derived 3.3 V rails or backup coin cells for power-loss memory retention. OTA capability enabled by the 256 KB flash lets installed endpoints receive stack and application updates without physical access, which is essential for large smart home fleets.
Direkomendasikan
iBeacon and Eddystone Beacons
Proximity beacons are an ideal single-purpose fit for the BLE113-A-M256K: the device only transmits periodic advertisement packets, so it can run for many months on a CR2032 cell within the module's 2.0 V to 3.6 V input range. A compact BGScript application configures the 256 KB flash to hold multiple beacon frames (iBeacon, Eddystone-URL, Eddystone-UID) and switch between them, while the integrated chip antenna provides consistent radiated output without RF tuning. Deployments in retail proximity marketing, asset tracking, and indoor navigation use the module's configurable advertising interval to trade beacon rate against battery life, and OTA updates allow re-flashing beacon identifiers across a fleet without physical retrieval.
Direkomendasikan
Industrial Wireless Sensor Nodes
Industrial condition-monitoring nodes measuring vibration, current, or temperature use the BLE113-A-M256K to bridge sensor frontends to smartphones and gateways without cabling. The module's SPI and UART interfaces connect to industrial ADCs and MCUs, PWM supports simple actuator or alarm outputs, and the castellated pads allow reflow soldering onto conformal-coated industrial PCBs. The -93 dBm sensitivity penetrates typical factory obstruction better than lower-sensitivity radios at Class 2 power, and operation down to 2.0 V permits direct battery backup designs. With the certified Bluetooth Smart stack on-module, integrators avoid RF layout risk in electrically noisy enclosures, and the 256 KB flash hosts protocol translation firmware alongside OTA maintenance images.
Direkomendasikan
Smartphone-Connected Consumer Devices
Consumer products that pair with a mobile app - toys, locks, scales, coffee machines, audio accessories - use the BLE113-A-M256K as the certified wireless interface. Because the Bluetooth 4.0 stack runs on-module and exposes a simple UART/SPI API, the host MCU only needs to implement product logic, and the CC2541-based radio interoperates with every BLE-capable phone. The 2 Mbps air rate provides responsive app interaction, the chip antenna removes RF certification design work, and the 3.3 V-friendly supply integrates into typical consumer electronics rails. The 256 KB flash supports product-specific GATT services plus OTA update capability, letting manufacturers ship hardware early and refine firmware through app-triggered updates after launch.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk BLE113-A-M256K — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | BLE113-A-V1 | BLE113-A-M256K-MT4 | BLE121LR-A-M256K | BLE112-A-V1 |
|---|---|---|---|---|---|
| Package | BLE113 castellated SMD module, integrated chip antenna | BLE113 castellated SMD module - same footprint | BLE113 castellated SMD module - same footprint | Bluegiga castellated SMD module family | BLE112 castellated SMD module - footprint-compatible |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Flash Memory | 256 KB | 128 KB | 256 KB | 256 KB | 128 KB |
| Bluetooth Version | 4.0 (Bluetooth Smart) | 4.0 (Bluetooth Smart) | 4.0 (Bluetooth Smart) | 4.0 (Bluetooth Smart) | 4.0 (Bluetooth Smart) |
| Supply Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Range Class | Class 2 (standard range) | Class 2 (standard range) | Class 2 (standard range) | Long range (higher TX power) | Class 2 (standard range) |
| Availability Channel | DigiKey, Mouser, LCSC, Octopart (14 distributors) | Distribution (DigiKey, Mouser) | Direct Silicon Labs only (custom OPN) | Distribution | Distribution (legacy) |
Diferensiator Kunci
- Double the flash for OTA and large BGScript apps (vsBLE113-A-V1)
- Longer-range sibling with same flash (vsBLE121LR-A-M256K)
- Newer generation sensitivity (vsBLE112-A-V1)
Catatan Desain
Design the supply rail for 2.0 V to 3.6 V strictly; 3.3 V LDO output or a fresh lithium coin cell sits comfortably in range. Place a 100 nF ceramic capacitor close to the module supply pads plus bulk 10 uF for TX burst current. Estimated: BLE-class radios draw burst currents in the tens of milliamps during transmit; undersized decoupling causes brownout resets during connection events, so verify rail droop with an oscilloscope on first prototypes.
Respect the antenna keep-out: no copper pours, traces, ground planes, batteries, or metal enclosures in the region specified by the Silicon Labs datasheet around the integrated chip antenna end of the module. Even though the antenna is pre-tuned and certified, nearby dielectric or metal detunes it and can cost several dB of link margin. If the enclosure is metal, place the module at a plastic window or use an external antenna variant instead.
Confirm flash budget early: the -M256K was chosen over BLE113-A-V1 specifically for OTA updates or large BGScript applications, which consume the 256 KB quickly. If you later footprint-swap to BLE113-A-V1 (128 KB), OTA images plus application may no longer fit. Also note that BLE113-A-M256K-MT4 is a custom preloaded-firmware OPN available only direct from Silicon Labs - do not expect to source it from distribution.
Informasi Konformitas
RoHS compliance indicated by distributor listings (etei.com comparison covers RoHS status). REACH, halogen-free, and conflict mineral status not stated in provided data.
