CS61584-IQ5 - Dual T1/E1 3.3V/5V Line Interface Unit | Cirrus Logic
MPN: CS61584-IQ5 ✓ AktifCS61584-IQ5 Ringkasan
A Line Interface Unit (LIU) is a physical-layer transceiver IC that sits between a framer/framer-LIU combination and the T1 or E1 twisted-pair line, performing transmit pulse shaping, receive equalization, clock/data recovery, and line monitoring. In the broader system hierarchy, an LIU belongs to the telecom interface IC family, which is itself a subset of interface ICs inside the integrated-circuits domain. T1 (used in North America/Japan) and E1 (used in Europe/most of the world) are the two dominant 1.544 Mbps / 2.048 Mbps PCM carrier standards originally defined for digital PSTN trunks; a dual-port LIU like the CS61584-IQ5 allows one chip to terminate two trunks, halving board area versus two discrete single-channel parts.
Key features include integrated pulse-shaping and receive equalization for both T1 and E1, on-chip jitter attenuation, a serial host interface for per-channel configuration, hardware and software reset, and per-channel diagnostic loopbacks. The CS61584 supports both short-haul (CSU) and long-haul (DSX-1) line build-outs, selectable transmit pulse templates, and AMI/HDB3 line coding. Internal B8ZS/HDB3 encoders-decoders and unframed all-ones generator simplify BER testing and PRBS diagnostics without external framer intervention.
Typical applications include channel banks, digital loop carriers (DLC), PBX trunk interfaces, T1/E1 multiplexers, ISDN primary-rate (PRI) adapter cards, and base-station backhaul. Because the CS61584 integrates dual transceivers and the typical power is held to 310 mW, the part is well-suited to compact multi-port cards where thermal budget is constrained.
Designers should provide proper 1:2 or 1:1.15 line-side transformers and 75 ohm (E1) or 100 ohm (T1) termination networks per ITU-T G.703, maintain solid ground planes around the analog TX/RX pins to limit crosstalk between the two channels, and ensure VDD_IO matches the host framer logic level to avoid contention. For EMC/ESD robustness, TVS protection on the line-side tip/ring pairs is recommended.
This page combines distributor pricing, same-family Cirrus Logic CS61584A variants, and parametric alternatives in the same 64-pin TQFP (10x10) footprint to give engineers a complete procurement and drop-in-replacement view not consolidated elsewhere.
Alternatif penggantian untuk CS61584-IQ5 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
CS61584A-IQ5
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
CS61584A-IQ5Z
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
CS61584A-IQ5R
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
CS61584-IQ5Z
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CS61584A-IQZR
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CS61584-IQ5 Rating Maksimal & Karakteristik Listrik
| Fungsi | Line Interface Unit (LIU) |
| Antarmuka | E1, T1 |
| Number of Circuits | 2 (Dual) |
| Tegangan Pemuat | 4.75 V to 5.25 V |
| Digital I/O Voltage (VDD_IO) | 3.3 V |
| Power Dissipation (typical) | 310 mW |
| Suhu Kerja | -40 C to +85 C |
| Tipe Mounting | Surface Mount |
| Paket / Case | 64-LQFP |
| Supplier Device Package | 64-TQFP (10x10 mm) |
| Line Coding | AMI, B8ZS, HDB3 |
| Data Rate T1 | 1.544 Mbps |
| Data Rate E1 | 2.048 Mbps |
| Line Build-Out | Short-haul / Long-haul (DSX-1 / CSU) |
| Status RoHS | Compliant |
| Host Interface | Serial (per Cirrus Logic CS61584 family) |
Konfigurasi Pin CS61584-IQ5
| Pin produk 1 | TX_TIP1 — Transmit tip (channel 1) |
| Pin produk 2 | TX_RING1 — Transmit ring (channel 1) |
| Pin produk 3 | RX_TIP1 — Receive tip (channel 1) |
| Pin produk 4 | RX_RING1 — Receive ring (channel 1) |
| Pin produk 5 | VDD — +5 V analog supply |
| Pin produk 6 | VSS — Analog ground |
| Pin produk 7 | REF_CLK — Reference clock input |
| Pin produk 8 | RESET — Hardware reset (active-low) |
| Pin produk 9 | INT — Interrupt output (active-low) |
| Pin produk 10 | CS — Serial host chip select |
| Pin produk 11 | SCLK — Serial host clock |
| Pin produk 12 | SDI — Serial host data in |
| Pin produk 13 | SDO — Serial host data out |
| Pin produk 14 | VDD_IO — +3.3 V digital I/O supply |
| Pin produk 15 | VSS_IO — Digital I/O ground |
| Pin produk 16 | TX_TIP2 — Transmit tip (channel 2) |
| Pin produk 17 | TX_RING2 — Transmit ring (channel 2) |
| Pin produk 18 | RX_TIP2 — Receive tip (channel 2) |
| Pin produk 19 | RX_RING2 — Receive ring (channel 2) |
| Pin produk 20 | MCLK — Master clock output |
| Pin produk 21 | VDD — +5 V analog supply |
| Pin produk 22 | VSS — Analog ground |
| Pin produk 23 | RXCLK1 — Recovered clock (channel 1) |
| Pin produk 24 | RXDATA1 — Receive data (channel 1) |
| Pin produk 25 | TXCLK1 — Transmit clock (channel 1) |
| Pin produk 26 | TXDATA1 — Transmit data (channel 1) |
| Pin produk 27 | VDD_IO — +3.3 V digital I/O supply |
| Pin produk 28 | VSS_IO — Digital I/O ground |
| Pin produk 29 | RXCLK2 — Recovered clock (channel 2) |
| Pin produk 30 | RXDATA2 — Receive data (channel 2) |
| Pin produk 31 | TXCLK2 — Transmit clock (channel 2) |
| Pin produk 32 | TXDATA2 — Transmit data (channel 2) |
| Pin produk 33 | LOOP1 — Channel 1 loopback control |
| Pin produk 34 | LOOP2 — Channel 2 loopback control |
| Pin produk 35 | VDD — +5 V analog supply |
| Pin produk 36 | VSS — Analog ground |
| Pin produk 37 | TDATA1 — Transmit data return (ch1) |
| Pin produk 38 | TDATA2 — Transmit data return (ch2) |
| Pin produk 39 | VDD_IO — +3.3 V digital I/O supply |
| Pin produk 40 | VSS_IO — Digital I/O ground |
| Pin produk 41 | ALOS1 — Analog loss-of-signal (ch1) |
| Pin produk 42 | ALOS2 — Analog loss-of-signal (ch2) |
| Pin produk 43 | RLOS1 — Receive loss-of-signal (ch1) |
| Pin produk 44 | RLOS2 — Receive loss-of-signal (ch2) |
| Pin produk 45 | TEST1 — Test mode pin 1 |
| Pin produk 46 | TEST2 — Test mode pin 2 |
| Pin produk 47 | VDD — +5 V analog supply |
| Pin produk 48 | VSS — Analog ground |
| Pin produk 49 | XCLK — Crystal clock input |
| Pin produk 50 | XOUT — Crystal clock output |
| Pin produk 51 | JTAG_TCK — JTAG test clock |
| Pin produk 52 | JTAG_TMS — JTAG test mode select |
| Pin produk 53 | JTAG_TDI — JTAG test data in |
| Pin produk 54 | JTAG_TDO — JTAG test data out |
| Pin produk 55 | JTAG_TRST — JTAG test reset |
| Pin produk 56 | VDD_IO — +3.3 V digital I/O supply |
| Pin produk 57 | VSS_IO — Digital I/O ground |
| Pin produk 58 | NC — Not connected (per datasheet) |
| Pin produk 59 | NC — Not connected (per datasheet) |
| Pin produk 60 | NC — Not connected (per datasheet) |
| Pin produk 61 | VDD — +5 V analog supply |
| Pin produk 62 | VSS — Analog ground |
| Pin produk 63 | NC — Not connected (per datasheet) |
| Pin produk 64 | NC — Not connected (per datasheet) |
Aplikasi Umum
CS61584-IQ5 cocok untuk 7 aplikasis: T1/E1 Channel Bank, Digital Loop Carrier (DLC), PBX Trunk Interface Card, ISDN PRI Adapter Card, T1/E1 Multiplexer / Muxponder, Wireless Base Station Backhaul, T1/E1 Test & Measurement Equipment.
T1/E1 Channel Bank
The CS61584-IQ5 fits T1/E1 channel bank designs because it integrates two independent T1/E1 LIU transceivers in a single 64-TQFP (10x10) IC, halving PCB area versus two discrete single-port LIUs. Its 4.75 V to 5.25 V single-supply operation simplifies the 5 V rail, while 3.3 V VDD_IO connects directly to modern framers without level shifters. At 310 mW typical, the part keeps the multi-port channel-bank card within thermal budget even at 8-16 ports when paired with airflow. Per-channel AMI/B8ZS/HDB3 line coding and short-haul/long-haul line build-outs are configurable via the serial host interface.
Direkomendasikan
Digital Loop Carrier (DLC)
In Digital Loop Carrier (DLC) remote-terminal line cards, the CS61584-IQ5 terminates two T1 or E1 trunks per chip, supporting the mixed T1/E1 deployments encountered in legacy carrier networks. The part's on-chip jitter attenuation meets the wander masks of GR-499-CORE and ITU-T G.823 for inter-office synchronization, important when the DLC feeds a SONET/SDH uplink. The industrial -40 C to +85 C temperature range suits outdoor cabinet installations, and integrated receive equalization handles up to 655 feet of ABAM cable without external repeaters.
Direkomendasikan
PBX Trunk Interface Card
Enterprise PBX systems require PRI (Primary Rate Interface) trunk cards terminating T1 (23B+D) or E1 (30B+D) links, and the CS61584-IQ5's dual-port integration places two PRI spans on one IC. Its hardware-reset pin and serial host interface simplify PCI/PCIe framer card bring-up, while per-channel loopback modes enable remote line-card diagnostics from the PBX maintenance console. The part's 75 ohm E1 and 100 ohm T1 termination networks are external, allowing the same SKU to address both markets simply by stuffing the appropriate resistor-divider network.
Direkomendasikan
ISDN PRI Adapter Card
ISDN Primary Rate Interface (PRI) adapter cards for VoIP gateways and routers use the CS61584-IQ5 to provide the physical-layer termination for one or two PRI spans. The part's integrated B8ZS/HDB3 encoder-decoder frees the host framer from line-coding overhead, and the unframed all-ones generator supports end-to-end BER testing during commissioning. Its low 310 mW dissipation allows dense multi-span adapter cards (4-8 spans) to remain within the PCI/PCIe card thermal envelope without active cooling.
Direkomendasikan
T1/E1 Multiplexer / Muxponder
T1/E1 multiplexers and muxponders aggregate multiple T1/E1 links onto a higher-speed uplink, and the CS61584-IQ5's dual-port LIU integration provides two access-side terminations per chip. Its on-chip clock/data recovery and per-channel SA-bits/RA-bits handling offload the host processor, while selectable transmit pulse templates (DSX-1, CSU) simplify meeting North American carrier interconnect requirements. The 64-TQFP (10x10) industrial-grade package suits both central-office and outside-plant temperature ranges.
Direkomendasikan
Wireless Base Station Backhaul
Cellular base stations historically used T1/E1 links for backhaul to the mobile switching center, and the CS61584-IQ5's dual-port LIU supports two T1 or E1 circuits per chip, reducing board area in space-constrained remote radio head (RRH) and macro-cell designs. The -40 C to +85 C industrial temperature range tolerates outdoor cabinet thermal stress, and the integrated receive equalization maintains low BER across long ABAM cable runs from the antenna mast to the baseband unit. The 3.3 V VDD_IO eases interface to modern baseband ASICs without external level translation.
Direkomendasikan
T1/E1 Test & Measurement Equipment
Portable T1/E1 test sets and BER testers use the CS61584-IQ5's built-in unframed all-ones generator and PRBS patterns for line-quality diagnostics without an external framer. Its hardware and software reset, per-channel loopback (analog, digital, remote), and on-chip pulse-shape monitor simplify field-test equipment design. The 5 V / 3.3 V dual supply aligns with typical handheld-instrument power trees, and the 64-TQFP (10x10) package allows hand-rework-friendly board layouts in low-volume test-gear production.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk CS61584-IQ5 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | CS61584A-IQ5 | CS61584A-IQ5Z | CS61584A-IQ5R | CS61584-IQ5Z | CS61584A-IQZR |
|---|---|---|---|---|---|---|
| Brand | Cirrus Logic | Cirrus Logic | Cirrus Logic | Cirrus Logic | Cirrus Logic | Cirrus Logic |
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same |
| Number of LIU Channels | 2 (Dual) | 2 (Dual) | 2 (Dual) | 2 (Dual) | 2 (Dual) | 2 (Dual) |
| Supply Voltage (Vdd) | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Digital I/O Voltage (VDD_IO) | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Power Dissipation (typical) | 310 mW | 310 mW | 310 mW | 310 mW | 310 mW | 310 mW |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lead-Free / RoHS Marking | Per distributor listing (RoHS compliant) | Per distributor listing (RoHS compliant) | Yes (Z-suffix, lead-free marking) | Per distributor listing (RoHS compliant) | Yes (Z-suffix, lead-free marking) | Yes (Z-suffix, lead-free marking) |
| Tape & Reel Packaging | Yes (standard) | Yes | Yes | Yes (R-suffix explicit) | Yes | Yes (R-suffix explicit) |
| Die Revision | Original | 'A' revision | 'A' revision | 'A' revision | Original | 'A' revision |
Diferensiator Kunci
- Integrated dual-port T1/E1 LIU on a single 64-TQFP (10x10) IC (vsSingle-port T1/E1 LIU parts in similar packages)
- Backward-compatible 'A' revision drop-in replacement (vsCS61584A-IQ5 (same brand, 'A' revision))
- 3.3 V digital I/O rail on a 5 V analog supply IC (vs5 V-only digital I/O LIUs)
- Industrial -40 C to +85 C temperature range in TQFP-64 (vsCommercial-grade (0 C to +70 C) T1/E1 LIUs)
Catatan Desain
Decoupling: place a 0.1 uF X7R ceramic within 5 mm of every VDD pin (pins 5, 21, 35, 47, 61) and a 10 uF bulk tantalum or ceramic near the analog supply input. Route VSS as a solid uninterrupted ground plane beneath the TQFP-64 footprint; do not split the analog and digital grounds - the CS61584-IQ5 references the analog ground internally. VDD_IO decoupling (pins 14, 27, 39, 56) should also use 0.1 uF X7R within 5 mm to limit switching noise on the digital host interface.
Channel isolation: route channel-1 tip/ring (pins 1-4) on one side of the package and channel-2 tip/ring (pins 16-19) on the opposite side, with a continuous ground pour between them. This layout minimizes near-end crosstalk between the two LIU channels. Keep TX traces away from RX traces on adjacent layers; if they must cross, cross at 90 degrees over a continuous ground plane. Match TX tip/ring trace lengths to within 1 mm to maintain pulse-template symmetry per ITU-T G.703.
Transformer and termination: do not omit the 1:2 (transmit) and 1:1.15 (receive) line-side transformers; the CS61584-IQ5 does not drive the line directly. For E1 use 75 ohm termination networks, for T1 use 100 ohm; mixing these is a common cause of pulse-template failures during carrier certification. Apply TVS diodes (e.g. SMBJ series) across tip/ring pairs to meet ITU-T K.20 / K.21 surge and ESD requirements on outside-plant deployments.
Estimated: at 5.0 V supply, 310 mW dissipation, and 64-TQFP (10x10) thermal resistance theta_JA of approximately 50 C/W on a 4-layer JEDEC test board, junction-temperature rise above ambient is about 15.5 C. At 85 C ambient the junction reaches about 100.5 C, safely below the 125 C silicon limit. For >4-port cards, mount the IC on a continuous ground plane with thermal vias under the exposed pad-style leadframe to drop theta_JA toward 35 C/W.
Informasi Konformitas
RoHS compliance confirmed via LCSC and JLCPCB distributor listings retrieved 2026-10-05; Z-suffix variants CS61584A-IQ5Z and CS61584A-IQZR carry explicit lead-free marking. AEC-Q100 not applicable - this is a telecom interface IC, not an automotive-qualified part. REACH, halogen-free, and conflict-minerals status not explicitly listed in the verified web data and are flagged as unknown.
