DG423DY+ - Dual 35 Ohm CMOS Analog Switch | Maxim Integrated
MPN: DG423DY+ ✓ AktifDG423DY+ Ringkasan
A CMOS analog switch is an interface IC that uses MOSFET-based transmission paths to connect or disconnect signals. Within the semiconductor hierarchy, an analog switch belongs to the interface IC category, where it sits between a controlling digital circuit and an external analog signal. Unlike a mechanical relay, it changes state electronically and can route low-level signals without mechanical contact wear. The latch function is especially valuable when the selected signal path must remain stable while the control inputs return to an inactive state.
Key characteristics include a 35 ohm on-resistance, a 1:1 signal configuration, two switched circuits, a 16-pin SOIC package, and a rated operating voltage stated as 15 V. Published listings also identify the switch as an SPST, normally open device with a switching time of 250 ns and a leakage current of 500 pA. These figures position the DG423DY+ for precision signal isolation, sample-and-hold systems, instrumentation, and control interfaces where compactness and low off leakage are more important than very low on-resistance.
The DG423 family uses CMOS construction to combine low power consumption with high input impedance. Its latch-based control architecture separates the momentary command used to change a path from the stable state that maintains connectivity. Compared with continuously driven analog switches, this architecture can simplify firmware behavior because the selected path remains active without requiring the controller to hold a command signal. The 16-SOIC footprint also supports conventional surface-mount assembly and mixed analog/digital board layouts.
Typical uses include multiplexed sensor acquisition, precision measurement interfaces, sample-and-hold circuitry, automated test equipment, and low-level control-signal routing. The normally open topology provides a default disconnected condition when the device is reset or not actively commanded. In such systems, this behavior can reduce unintended signal coupling between circuit sections, although external pull resistors may still be required to establish a defined state during power-up.
Layout should preserve short analog traces, place input and output paths away from fast digital clocks, and route supply and ground connections carefully to minimize switching transients coupling into sensitive signals. Because the switch adds 35 ohms in its conducting state, source impedance, capacitance, and the impedance of the receiving circuit should be evaluated together. For applications needing more channels, adjacent Maxim DG-series devices can simplify design, but function and control compatibility must be checked independently.
This page organizes the DG423DY+ identity, documented electrical characteristics, practical applications, package information, and sourcing information into an engineering-focused guide. It also distinguishes verified device facts from specifications that require confirmation in the manufacturer datasheet, helping designers plan a compliant 16-SOIC analog-switch implementation without relying on generic connector or relay assumptions.
Alternatif penggantian untuk DG423DY+ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Tidak ada alternatif pengganti yang tersedia untuk produk ini.
Permintaan AlternatifDG423DY+ Rating Maksimal & Karakteristik Listrik
| Number of Switched Circuits | 2 circuits |
| Multiplexer Configuration | 1:1 |
| Switch Configuration | SPST normally open |
| On-Resistance | 35 ohm |
| Switching Time | 250 ns |
| Leakage Current | 500 pA |
| Rated Operating Voltage | 15 V |
| Control Interface | Latched CMOS control |
| Technology | CMOS |
| Power Class | Low-power |
| Temperature Grade | Industrial |
| Paket | 16-SOIC |
| Jumlah Pin | 16 pins |
| Package Shape | Rectangular |
| Tipe Mounting | Surface mount |
| Body Width | 3.90 mm |
| Lead Pitch | 0.154 inch |
DG423DY+ rectangular Diamant Konfigurasi Panduan
Konfigurasi pin untuk DG423DY+ (rectangular pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DG423DY+.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DG423DY+ cocok untuk 6 aplikasis: Precision Sensor Signal Multiplexing, Sample-and-Hold Signal Conditioning, Automated Test Equipment Signal Routing, Industrial Control Signal Isolation, Battery-Powered Portable Instrumentation, External Interface Line Routing.
Precision Sensor Signal Multiplexing
The DG423DY+ is suitable for routing low-level sensor signals when the system needs two independent, normally open paths with a latched configuration. Its stated 35 ohm on-resistance should be included in the source-impedance calculation, while the 500 pA leakage figure is relevant when high-impedance sensors are connected. The 250 ns switching time supports moderate-bandwidth acquisition rather than the fastest sampling systems. Because the device is normally open, it also provides a default isolation condition that can reduce unintended coupling between sensor branches during reset or control transitions.
Direkomendasikan
Sample-and-Hold Signal Conditioning
The two latched SPST paths in the DG423DY+ can support acquisition and isolation functions in a sample-and-hold architecture. When a path conducts, its 35 ohm resistance contributes to the effective source impedance seen by the holding capacitor, so acquisition time must be calculated with the sensor output, switch, and capacitor together. The stated 250 ns switching time describes the switching interval but does not replace the separate settling-time calculation. The normally open topology also helps isolate the held node when the switch is not selected.
Direkomendasikan
Automated Test Equipment Signal Routing
DG423DY+ fits compact automated test equipment that must connect test points under digital control while retaining the selected route. Its latched operation allows the controller to issue a command and then move on without continuously driving the control state. Two normally open circuits can isolate one DUT interface when another path is active. The 35 ohm resistance can affect high-impedance measurements, while the 500 pA leakage specification should be checked against the leakage floor of the instrument. The 16-SOIC package also supports conventional board-level automation.
Direkomendasikan
Industrial Control Signal Isolation
The DG423DY+ can isolate low-level control or return paths in an industrial controller when default-open behavior is preferred. A normally open switch presents a disconnected condition until the control sequence selects the path, which can help prevent unintended command-line coupling during startup or reset. The stated 15 V operating voltage must be checked against the actual signal amplitude and supply environment, while industrial temperature-grade labeling supports deployment in suitable industrial conditions. Signal integrity depends on keeping analog traces short and routing them away from switching nodes and high-current outputs.
Direkomendasikan
Battery-Powered Portable Instrumentation
The low-power CMOS construction and latched state of the DG423DY+ can suit battery-powered instrumentation where minimizing sustained control activity is important. Once configured, the analog path can remain in its selected state without a continuously asserted command signal. The 35 ohm on-resistance must be acceptable for the sensor and amplifier input, and the 500 pA leakage figure is particularly relevant when working with high-impedance nodes. The compact 16-SOIC footprint leaves board area for the power system, analog front end, and user interface.
Direkomendasikan
External Interface Line Routing
The DG423DY+ can route external interface lines when a circuit requires a normally open, electronically controlled connection and an isolated default state. This behavior is useful around removable or externally accessible interfaces because the path can be disconnected by default and asserted only under valid operating conditions. Its stated 500 pA leakage and 35 ohm resistance should be considered alongside connector leakage, ESD-protection components, and the receiving input impedance. The latch function supports stable routing, while the 16-SOIC package permits straightforward integration beside connector and protection circuitry.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DG423DY+ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini |
|---|---|
| Brand | Maxim Integrated |
| Package | 16-SOIC |
| Switch Type | SPST normally open |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | 1:1 |
| On-Resistance | 35 ohm |
| Switching Time | 250 ns |
| Leakage Current | 500 pA |
| Rated Operating Voltage | 15 V |
| Control Function | Latched CMOS control |
Catatan Desain
Include the 35 ohm on-resistance when calculating source impedance, voltage division, and capacitor settling time. For a sample-and-hold node, the effective resistance seen by the holding capacitor includes the signal source, the selected DG423DY+ path, and the capacitor's effective series resistance. Confirm that the resulting acquisition interval accommodates the stated 250 ns switching time and the circuit's required settling accuracy.
Use the 16-SOIC package drawing and pin-description table in the manufacturer datasheet to create the land pattern. Place input and output traces close to their associated pins and provide a continuous ground reference beneath the device. Keep high-impedance analog nodes away from clocks, relay drivers, inductors, and other switching-current paths to reduce capacitive feedthrough and unintended coupling.
Do not treat the latched state as a guarantee of a defined electrical state during initial power-up. Confirm the control truth table, input logic levels, and power-on behavior in the manufacturer datasheet. If a connected node must remain at a known potential, use suitable external bias or pull components after verifying their effect on leakage, signal level, and power consumption.
Minimize loop area around switched terminals and sensitive receivers because charge injection and switching transients can appear at the output even when the control edge is clean. Maintain separation from high-current switching paths, provide local supply decoupling where required by the application, and evaluate the assembled board with an oscilloscope when the switched signal is small relative to digital control-edge energy.
Informasi Konformitas
The device is identified as industrial temperature grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from current Maxim Integrated documentation.