Maxim Integrated

DG423DY+ - Dual 35 Ohm CMOS Analog Switch | Maxim Integrated

Артикул: DG423DY+ ✓ Активен
15 V Vdss 500 pA Id 35 ohm Rds(on) 16-SOIC Package
MOQ: 1 |

DG423DY+ Обзор

Maxim Integrated DG423DY+ is a dual-circuit, 1:1 CMOS analog switch with a stated on-resistance of 35 ohms in a 16-pin SOIC package. The device is identified as an improved low-power CMOS analog switch with latches, allowing the switched paths to retain their configuration without a continuing control input. The DG423DY+ provides normally open SPST switching and is intended for low-power analog signal routing where low leakage, compact packaging, and latched operation are useful.

A CMOS analog switch is an interface IC that uses MOSFET-based transmission paths to connect or disconnect signals. Within the semiconductor hierarchy, an analog switch belongs to the interface IC category, where it sits between a controlling digital circuit and an external analog signal. Unlike a mechanical relay, it changes state electronically and can route low-level signals without mechanical contact wear. The latch function is especially valuable when the selected signal path must remain stable while the control inputs return to an inactive state.

Key characteristics include a 35 ohm on-resistance, a 1:1 signal configuration, two switched circuits, a 16-pin SOIC package, and a rated operating voltage stated as 15 V. Published listings also identify the switch as an SPST, normally open device with a switching time of 250 ns and a leakage current of 500 pA. These figures position the DG423DY+ for precision signal isolation, sample-and-hold systems, instrumentation, and control interfaces where compactness and low off leakage are more important than very low on-resistance.

The DG423 family uses CMOS construction to combine low power consumption with high input impedance. Its latch-based control architecture separates the momentary command used to change a path from the stable state that maintains connectivity. Compared with continuously driven analog switches, this architecture can simplify firmware behavior because the selected path remains active without requiring the controller to hold a command signal. The 16-SOIC footprint also supports conventional surface-mount assembly and mixed analog/digital board layouts.

Typical uses include multiplexed sensor acquisition, precision measurement interfaces, sample-and-hold circuitry, automated test equipment, and low-level control-signal routing. The normally open topology provides a default disconnected condition when the device is reset or not actively commanded. In such systems, this behavior can reduce unintended signal coupling between circuit sections, although external pull resistors may still be required to establish a defined state during power-up.

Layout should preserve short analog traces, place input and output paths away from fast digital clocks, and route supply and ground connections carefully to minimize switching transients coupling into sensitive signals. Because the switch adds 35 ohms in its conducting state, source impedance, capacitance, and the impedance of the receiving circuit should be evaluated together. For applications needing more channels, adjacent Maxim DG-series devices can simplify design, but function and control compatibility must be checked independently.

This page organizes the DG423DY+ identity, documented electrical characteristics, practical applications, package information, and sourcing information into an engineering-focused guide. It also distinguishes verified device facts from specifications that require confirmation in the manufacturer datasheet, helping designers plan a compliant 16-SOIC analog-switch implementation without relying on generic connector or relay assumptions.

Аналоги без доработки для DG423DY+ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

DG423DY+ Максимальные параметры и электрические характеристики

Number of Switched Circuits 2 circuits
Multiplexer Configuration 1:1
Switch Configuration SPST normally open
On-Resistance 35 ohm
Switching Time 250 ns
Leakage Current 500 pA
Rated Operating Voltage 15 V
Control Interface Latched CMOS control
Technology CMOS
Power Class Low-power
Temperature Grade Industrial
Корпус 16-SOIC
Число выводов 16 pins
Package Shape Rectangular
Тип монтажа Surface mount
Body Width 3.90 mm
Lead Pitch 0.154 inch

Руководство по цоколевке DG423DY+ в корпусе rectangular

Цоколевка для DG423DY+ (корпус rectangular). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса rectangular для DG423DY+

Нет подробных данных о распиновке для DG423DY+.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

DG423DY+ подходит для 6 применениеs: Precision Sensor Signal Multiplexing, Sample-and-Hold Signal Conditioning, Automated Test Equipment Signal Routing, Industrial Control Signal Isolation, Battery-Powered Portable Instrumentation, External Interface Line Routing.

🧩

Precision Sensor Signal Multiplexing

The DG423DY+ is suitable for routing low-level sensor signals when the system needs two independent, normally open paths with a latched configuration. Its stated 35 ohm on-resistance should be included in the source-impedance calculation, while the 500 pA leakage figure is relevant when high-impedance sensors are connected. The 250 ns switching time supports moderate-bandwidth acquisition rather than the fastest sampling systems. Because the device is normally open, it also provides a default isolation condition that can reduce unintended coupling between sensor branches during reset or control transitions.

📺

Sample-and-Hold Signal Conditioning

The two latched SPST paths in the DG423DY+ can support acquisition and isolation functions in a sample-and-hold architecture. When a path conducts, its 35 ohm resistance contributes to the effective source impedance seen by the holding capacitor, so acquisition time must be calculated with the sensor output, switch, and capacitor together. The stated 250 ns switching time describes the switching interval but does not replace the separate settling-time calculation. The normally open topology also helps isolate the held node when the switch is not selected.

🏭

Automated Test Equipment Signal Routing

DG423DY+ fits compact automated test equipment that must connect test points under digital control while retaining the selected route. Its latched operation allows the controller to issue a command and then move on without continuously driving the control state. Two normally open circuits can isolate one DUT interface when another path is active. The 35 ohm resistance can affect high-impedance measurements, while the 500 pA leakage specification should be checked against the leakage floor of the instrument. The 16-SOIC package also supports conventional board-level automation.

⚡

Industrial Control Signal Isolation

The DG423DY+ can isolate low-level control or return paths in an industrial controller when default-open behavior is preferred. A normally open switch presents a disconnected condition until the control sequence selects the path, which can help prevent unintended command-line coupling during startup or reset. The stated 15 V operating voltage must be checked against the actual signal amplitude and supply environment, while industrial temperature-grade labeling supports deployment in suitable industrial conditions. Signal integrity depends on keeping analog traces short and routing them away from switching nodes and high-current outputs.

📱

Battery-Powered Portable Instrumentation

The low-power CMOS construction and latched state of the DG423DY+ can suit battery-powered instrumentation where minimizing sustained control activity is important. Once configured, the analog path can remain in its selected state without a continuously asserted command signal. The 35 ohm on-resistance must be acceptable for the sensor and amplifier input, and the 500 pA leakage figure is particularly relevant when working with high-impedance nodes. The compact 16-SOIC footprint leaves board area for the power system, analog front end, and user interface.

🌐

External Interface Line Routing

The DG423DY+ can route external interface lines when a circuit requires a normally open, electronically controlled connection and an isolated default state. This behavior is useful around removable or externally accessible interfaces because the path can be disconnected by default and asserted only under valid operating conditions. Its stated 500 pA leakage and 35 ohm resistance should be considered alongside connector leakage, ESD-protection components, and the receiving input impedance. The latch function supports stable routing, while the 16-SOIC package permits straightforward integration beside connector and protection circuitry.

What is the DG423DY+?
The DG423DY+ is a dual-circuit, normally open SPST CMOS analog switch from Maxim Integrated. It provides a 1:1 configuration, a stated on-resistance of 35 ohms, a switching time of 250 ns, and a 16-SOIC package. According to the manufacturer datasheet, the device is an improved low-power CMOS analog switch with a latch, allowing the selected signal path to remain in its commanded state.
What are the key specifications of DG423DY+ that engineers should know?
The DG423DY+ combines two normally open SPST circuits with a 35 ohm on-resistance, 250 ns switching time, 500 pA leakage current, and 15 V rated operating voltage. It is packaged in a 16-pin surface-mount SOIC and uses latched CMOS control. According to the Maxim Integrated datasheet, the latch retains the switched state after the control action is completed, simplifying designs that require stable analog routing.
Is the DG423DY+ a SPST or SPDT analog switch?
The DG423DY+ is a normally open SPST analog switch with two circuits and a 1:1 configuration. It does not provide the alternate common-contact path characteristic of an SPDT device. According to Maxim Integrated product descriptions, the latch and normally open topology suit applications where a default isolated condition is desirable between externally accessible lines and internal circuitry.
What package does the DG423DY+ use?
The DG423DY+ uses a 16-SOIC surface-mount package with a rectangular body. Published dimensional information identifies a body width of 3.90 mm and a lead pitch of 0.154 inch. According to the manufacturer datasheet, the pin functions and package outline should be used as the controlling references for land-pattern design and assembly.
Where can I find the DG423DY+ datasheet and pinout?
The DG423DY+ datasheet PDF can be accessed through the listed Maxim Integrated document mirror, while the manufacturer pin-description table and package drawing should govern PCB assignments. The device uses 16 pins in an SOIC package. Use the pin-description table in the manufacturer datasheet when assigning control, common, and switched-terminal connections rather than inferring connections from package position.
How much on-resistance does the DG423DY+ have?
The DG423DY+ has a stated on-resistance of 35 ohms in the conducting state. According to the Maxim Integrated datasheet, the exact resistance depends on the applied voltage and current conditions, so the complete characterization table should be consulted for the operating point. That value must also be included when calculating voltage error and settling behavior in high-impedance signal paths.
What can replace the DG423DY+?
A valid replacement must match the 16-SOIC footprint, pin functions, normally open SPST topology, latch behavior, voltage rating, and critical switching parameters. No verified pin-compatible drop-in substitute was identified for the DG423DY+ in the available cross-reference results. DG419DY+, DG408DY+, and DG444DJ+ are related Maxim devices, but their different switching functions or pin assignments require schematic and footprint verification before replacement.
Is DG423DY+ the same as DG419DY+?
No. The DG423DY+ is a dual normally open SPST switch with latching, whereas the DG419DY+ is a related dual SPDT device. Although both Maxim Integrated products use related 16-pin SOIC packaging, a SPDT common-contact topology cannot be assumed to be pin-compatible with a normally open SPST connection. Use the individual datasheets to compare terminal assignments and control logic.
What is the best Maxim Integrated equivalent for DG423DY+?
No exact Maxim Integrated drop-in equivalent is established by the available cross-reference results. The closest functional alternatives are other DG-series analog switches, but changing among DG419DY+, DG408DY+, and DG444DJ+ changes the switching architecture or terminal count. For a genuine drop-in decision, confirm the 16-pin land pattern, control truth table, terminal assignments, maximum voltage, and latch behavior in the manufacturer datasheets.
When should I choose the DG423DY+ over another analog switch?
Choose the DG423DY+ when the circuit needs two normally open, latched signal paths, a compact 16-SOIC implementation, and a stated 35 ohm on-resistance. It is especially suitable when a default open condition is useful and the controller should not need to hold an active drive command. Select another switch when SPDT routing, greater channel count, lower resistance, or different terminal timing is required.
Is the DG423DY+ suitable for precision signal acquisition?
The DG423DY+ can be suitable for precision signal acquisition when its 500 pA leakage and 35 ohm on-resistance fit the source and measurement circuit. The switching time is 250 ns, while the latch supports stable path selection. Performance still depends on source impedance, capacitance, settling time, and the leakage and error characteristics of the connected analog front end.
How should DG423DY+ be used in a sample-and-hold circuit?
Use the DG423DY+ to connect the sampled signal to the holding network when the control path is asserted, then use the latched state to preserve that selection. Because the switch contributes 35 ohms and has a stated 250 ns switching time, account for settling across the combined switch, source, and capacitor impedance. Confirm hold behavior, leakage, and charge injection against the application requirements.
What power and environmental information should be checked before using DG423DY+?
The published operating voltage is 15 V, and the device is identified as an industrial-temperature-grade, low-power CMOS switch. Before deployment, verify the exact operating-voltage limits, supply requirements, control logic levels, power consumption, and environmental ratings in the Maxim Integrated datasheet. Compliance attributes including RoHS and REACH should be confirmed from the current manufacturer documentation or declaration.
Where can I buy DG423DY+ and check current stock?
Use the Request a Quote form on this page to request current DG423DY+ availability, lead time, and order handling. A distributor listing states that the DG423DY+ can ship today, but stock levels and delivery timing can change rapidly. Provide the exact 16-SOIC ordering code when requesting a quotation to avoid confusion with the related DG419DY+, DG408DY+, or DG444DJ+ devices.
What is the lead time for DG423DY+?
The current lead time for DG423DY+ should be requested through the Request a Quote form on this page. The verified product listing confirms that DG423DY+ is offered for purchase and indicates same-day shipment capability, but it does not establish a fixed lead time for every quantity. Share the required quantity and date code requirements so the order can be planned against current factory and distribution status.
What is the price of DG423DY+?
Use the Request a Quote form on this page for the current DG423DY+ price and volume-break review. The verified listing does not contain an explicit quantity-break price table, so no static price is reproduced here. Quote requests should specify the required quantity, package suffix, date-code preference, and target delivery location to obtain a current commercial response.

Справочные инженерные данные для DG423DY+ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the DG423DY+ when the design requires two normally open SPST paths, latched routing, a 16-SOIC footprint, and a stated 35 ohm on-resistance. Its default-open behavior is useful for isolating external lines, separating sensor branches, and preventing unintended command paths during reset. The DG419DY+ should be considered instead when SPDT routing is required, but its terminal assignments and common-contact architecture require schematic verification. The DG408DY+ belongs to a broader multiplexed-routing family and should be used only when its channel count, truth table, and pinout satisfy the design. The DG444DJ+ offers a related DG-series function, but it should not be treated as a direct replacement unless its switch topology, package pins, latch behavior, and electrical ratings align with the existing board. For every alternative, verify the exact ordering suffix, pinout, control truth table, voltage limits, switching time, leakage, and on-resistance before approving a substitution.

Сравнение с аналогами

Параметр Этот товар
Brand Maxim Integrated
Package 16-SOIC
Switch Type SPST normally open
Number of Circuits 2 circuits
Multiplexer Configuration 1:1
On-Resistance 35 ohm
Switching Time 250 ns
Leakage Current 500 pA
Rated Operating Voltage 15 V
Control Function Latched CMOS control

Заметки по проектированию

Include the 35 ohm on-resistance when calculating source impedance, voltage division, and capacitor settling time. For a sample-and-hold node, the effective resistance seen by the holding capacitor includes the signal source, the selected DG423DY+ path, and the capacitor's effective series resistance. Confirm that the resulting acquisition interval accommodates the stated 250 ns switching time and the circuit's required settling accuracy.

Use the 16-SOIC package drawing and pin-description table in the manufacturer datasheet to create the land pattern. Place input and output traces close to their associated pins and provide a continuous ground reference beneath the device. Keep high-impedance analog nodes away from clocks, relay drivers, inductors, and other switching-current paths to reduce capacitive feedthrough and unintended coupling.

Do not treat the latched state as a guarantee of a defined electrical state during initial power-up. Confirm the control truth table, input logic levels, and power-on behavior in the manufacturer datasheet. If a connected node must remain at a known potential, use suitable external bias or pull components after verifying their effect on leakage, signal level, and power consumption.

Minimize loop area around switched terminals and sensitive receivers because charge injection and switching transients can appear at the output even when the control edge is clean. Maintain separation from high-current switching paths, provide local supply decoupling where required by the application, and evaluate the assembled board with an oscilloscope when the switched signal is small relative to digital control-edge energy.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The device is identified as industrial temperature grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from current Maxim Integrated documentation.

Данные проверены: 2026-11-10 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

DG423DY+ datasheet DG423DY+ pinout DG423DY+ specifications DG423DY+ datasheet pdf DG423DY+ equivalent DG423DY+ replacement DG423DY+ cross reference DG423DY+ 35 ohm switch DG423DY+ 16-SOIC DG423DY+ sample and hold DG423DY+ vs DG419DY+ Maxim Integrated DG423DY+ DG423DY+ price DG423DY+ stock how to use DG423DY+

Связанные компоненты & термины

Maxim Integrated DG423DY+ DG419DY+ DG408DY+ DG444DJ+ CMOS analog switch analog switch interface IC semiconductor SPST switch normally open switch latched control on-resistance switching time leakage current 16-SOIC SOIC package family surface-mount package sample-and-hold circuit signal multiplexing sensor interface industrial instrumentation external line isolation charge injection RoHS REACH
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ