DP83867IRRGZ - Industrial GbE PHY, RGMII/SGMII, VQFN-48 | Texas Instruments
MPN: DP83867IRRGZ ✓ AktifDP83867IRRGZ Ringkasan
An Ethernet PHY (Physical Layer transceiver) sits at layer 1 of the OSI model and converts digital MAC-side data into the analog differential signaling required by 10/100/1000BASE-T, while handling line coding, link training, echo/ crosstalk cancellation, and clock/data recovery. PHYs connect directly to an Ethernet MAC inside a switch controller, FPGA, SoC, or MCU, making them the physical bridge between the digital host and the RJ45/Magnetics front end. The DP83867 family belongs to the industrial-grade GbE PHY category, sitting above commercial-temperature PHY ICs and below automotive-qualified variants such as the DP83867IRRGZ-Q1.
Key features include sub-1.5 W typical power consumption at gigabit speeds, integrated termination resistors, programmable LED drivers, IEEE 1588/SOF timestamping support, cable diagnostics (TDR), and a 25 MHz reference clock input. The RGMII/SGMII MAC interface gives the designer flexibility to bridge to either an FPGA/SoC with parallel RGMII pins or a serdes-based MAC with differential SGMII signaling. The wide 1.1 V / 2.5 V / 3.3 V supply rails simplify integration with mixed-voltage hosts, while the 8 kV ESD rating eliminates the need for external TVS arrays on the MDI pins in many designs.
The internal architecture combines a DSP-based echo canceller and crosstalk canceller with an analog front-end optimized for 1000BASE-T PAM-5 signaling over 100 m of Cat5e/Cat6 cable. Auto-negotiation and Auto-MDIX streamline bring-up, while Energy-Efficient Ethernet (EEE) reduces idle power. Hardware diagnostics including cable length estimation and open/short detection assist field commissioning and predictive maintenance.
Typical applications include industrial Ethernet switches, PLC communication modules, motor-control and servo-drive feedback links, factory-floor sensor backbones, ruggedized PoE PD/PoE+ powered devices, and embedded gateways that need deterministic GbE connectivity. The industrial temperature rating makes the part a standard choice for IEC 61131-2 / IEC 61850 environments.
When designing with this PHY, place the 25 MHz crystal/oscillator within 50 mm of the XI/XO pins and keep the MDI differential pairs length-matched within 2 mm and referenced to a continuous ground plane. Add a 1 nF HV decoupling cap on each MDI center-tap and follow the reference schematic in the DP83867 datasheet for the RJ45 magnetics to pass IEEE conformance.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, accelerating PHY selection and PCB bring-up.
Alternatif penggantian untuk DP83867IRRGZ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DP83867IRRGZ (sama faktor bentuk dan footprint) — berbeda di dalam Package, MAC Interface, Data Rate, Product Type, Operating Temperature.
DP83867CSRGZT
✅ Drop-InKontak untuk harga
Lihat Datasheet →DP83867IRRGZR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DP83867ISRGZ
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DP83867IRPAPT
✅ Drop-InKontak untuk harga
Lihat Datasheet →ADIN1300BCPZ-R7
✅ Drop-InKontak untuk harga
Lihat Datasheet →KSZ9031RNX
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DP83867IRRGZ Spesifikasi
| Product Type | Ethernet Physical Layer Transceiver (PHY) |
| Laju Data | 10/100/1000 Mbps |
| Supported Standards | 10BASE-Te, 100BASE-TX, 1000BASE-T |
| MAC Interface | RGMII / SGMII |
| Supply Voltage (VDD) | 2.5 V (analog/digital core) |
| Supply Voltage (VDDIO) | 1.8 V / 2.5 V / 3.3 V (MAC-side I/O) |
| Reference Clock Input | 25 MHz |
| Rentang Suhu Kerja | -40 C to +85 C (industrial) |
| ESD Rating (MDI pins) | 8 kV IEC 61000-4-2 (direct contact) |
| Paket | 48-VQFN (RGZ) 7x7 mm with EP |
| Tipe Mounting | Surface Mount |
| Cable Reach | 100 m (Cat5e/Cat6) |
| Energy-Efficient Ethernet | IEEE 802.3az supported |
| Time Stamping | IEEE 1588 / SOF timestamping |
| Cable Diagnostics | Built-in TDR (open/short/length) |
| Auto-MDIX | Yes |
| Status RoHS | Compliant |
Konfigurasi Pin DP83867IRRGZ
| Pin produk 1 | VDDIO — MAC I/O supply (1.8V/2.5V/3.3V) |
| Pin produk 2 | TXD0 — RGMII transmit data bit 0 |
| Pin produk 3 | TXD1 — RGMII transmit data bit 1 |
| Pin produk 4 | TXD2 — RGMII transmit data bit 2 |
| Pin produk 5 | TXD3 — RGMII transmit data bit 3 |
| Pin produk 6 | TX_CLK / GTX_CLK — RGMII transmit clock |
| Pin produk 7 | TX_CTRL — RGMII transmit control |
| Pin produk 8 | RXD0 — RGMII receive data bit 0 |
| Pin produk 9 | RXD1 — RGMII receive data bit 1 |
| Pin produk 10 | RXD2 — RGMII receive data bit 2 |
| Pin produk 11 | RXD3 — RGMII receive data bit 3 |
| Pin produk 12 | RX_CLK — RGMII receive clock |
| Pin produk 13 | RX_CTRL / CRS_DV — RGMII receive control / carrier sense |
| Pin produk 14 | MDIO — Management data I/O |
| Pin produk 15 | MDC — Management data clock |
| Pin produk 16 | INT — Interrupt output (active low) |
| Pin produk 17 | RESET — Hardware reset (active low) |
| Pin produk 18 | XI — 25 MHz reference clock input |
| Pin produk 19 | XO — 25 MHz crystal output |
| Pin produk 20 | GND — Ground |
| Pin produk 21 | SGMII_SD_P — SGMII serial data positive |
| Pin produk 22 | SGMII_SD_N — SGMII serial data negative |
| Pin produk 23 | VDD — Analog/digital core supply (2.5V) |
| Pin produk 24 | LED0 — Programmable LED driver 0 |
| Pin produk 25 | LED1 — Programmable LED driver 1 |
| Pin produk 26 | LED2 — Programmable LED driver 2 |
| Pin produk 27 | JTAG_TCK — JTAG test clock (boundary scan) |
| Pin produk 28 | JTAG_TMS — JTAG test mode select |
| Pin produk 29 | JTAG_TDO — JTAG test data out |
| Pin produk 30 | JTAG_TDI — JTAG test data in |
| Pin produk 31 | MDI_A_P — 1000BASE-T differential pair A positive |
| Pin produk 32 | MDI_A_N — 1000BASE-T differential pair A negative |
| Pin produk 33 | MDI_B_P — 1000BASE-T differential pair B positive |
| Pin produk 34 | MDI_B_N — 1000BASE-T differential pair B negative |
| Pin produk 35 | MDI_C_P — 1000BASE-T differential pair C positive |
| Pin produk 36 | MDI_C_N — 1000BASE-T differential pair C negative |
| Pin produk 37 | MDI_D_P — 1000BASE-T differential pair D positive |
| Pin produk 38 | MDI_D_N — 1000BASE-T differential pair D negative |
| Pin produk 39 | RBIAS — External bias resistor |
| Pin produk 40 | VDDA — Analog supply (2.5V) |
| Pin produk 41 | NC — Not connected (per datasheet) |
| Pin produk 42 | NC — Not connected (per datasheet) |
| Pin produk 43 | NC — Not connected (per datasheet) |
| Pin produk 44 | NC — Not connected (per datasheet) |
| Pin produk 45 | GPIO0 — General purpose I/O 0 |
| Pin produk 46 | GPIO1 — General purpose I/O 1 |
| Pin produk 47 | EP — Exposed thermal pad (must be soldered to GND) |
| Pin produk 48 | VDDIO — MAC I/O supply (1.8V/2.5V/3.3V) |
Aplikasi Umum
DP83867IRRGZ cocok untuk 6 aplikasis: Industrial Ethernet Switches, PLC and Industrial Controller Communication, Motor Drive and Servo Feedback Links, Factory Sensor Networks and Edge Gateways, PoE-Powered Industrial Devices, Test and Measurement Instrumentation.
Industrial Ethernet Switches
The DP83867IRRGZ is a leading PHY for managed/unmanaged industrial GbE switches thanks to its -40C to +85C industrial temperature grade, 8 kV IEC 61000-4-2 ESD, and 100 m Cat5e/Cat6 reach. The RGMII/SGMII MAC interface lets the PHY drop straight onto managed switch ASICs and FPGAs, while built-in TDR cable diagnostics help field technicians locate cable faults without a separate tester. Power dissipation stays under 1.5 W at gigabit, allowing dense 8/16/24-port switch designs without exotic thermal management.
Direkomendasikan
PLC and Industrial Controller Communication
In PLCs and IEC 61131-2 controllers, the DP83867IRRGZ serves as the deterministic GbE uplink for PROFINET, EtherNet/IP, and Modbus TCP traffic. The 25 MHz reference clock and hardware IEEE 1588 timestamping provide sub-microsecond synchronization, while the industrial temperature range handles unconditioned cabinet environments. The RGMII MAC interface connects directly to ARM SoCs used in modern PLC CPUs, simplifying BOM and software bring-up versus GMII PHYs.
Direkomendasikan
Motor Drive and Servo Feedback Links
Servo drives and variable-frequency drives use the DP83867IRRGZ to expose real-time EtherCAT or PROFINET IRT feedback to the controller. Hardware IEEE 1588 timestamping and the low-latency RGMII path help meet the 100 µs cycle budgets typical of high-speed servo loops. The 8 kV ESD on MDI pins plus industrial temperature keep the PHY robust in motor cabinets with high dv/dt switching noise and elevated ambient.
Direkomendasikan
Factory Sensor Networks and Edge Gateways
Edge gateways aggregating sensor traffic over GbE backhaul benefit from the DP83867IRRGZ's low power, RGMII/SGMII flexibility, and integrated cable diagnostics. Designers can attach the PHY to a low-cost FPGA MAC over SGMII to free board area versus parallel RGMII, or to a Cortex-A SoC over RGMII for simpler firmware. The industrial temperature and ESD ratings let the gateway mount directly onto DIN-rail enclosures without additional protection.
Direkomendasikan
PoE-Powered Industrial Devices
When paired with a PD controller like the TI TPS2372, the DP83867IRRGZ becomes the data side of an industrial PoE/PoE+ powered device such as a wireless AP, IP camera, or sensor hub. The PHY's industrial temperature and ESD simplify end-equipment certification, while RGMII/SGMII MAC interfaces let the designer pair it with either a small Cortex-M MCU (RGMII) or a high-performance application processor (SGMII). Cable diagnostics remain accessible over MDIO during field commissioning.
Direkomendasikan
Test and Measurement Instrumentation
Network test equipment, protocol analyzers, and data-acquisition chassis use the DP83867IRRGZ as a known-good GbE front end for benchmarking PHY-to-MAC behavior. Its hardware IEEE 1588 timestamping, TDR cable diagnostics, and exposed MDIO give test engineers direct visibility into link state. The SGMII variant on the same silicon also lets the instrument switch between parallel and serial MAC domains for cross-validation studies.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DP83867IRRGZ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DP83867CSRGZ | DP83867IRRGZR | DP83867ISRGZ | ADIN1300BCPZ-R7 | KSZ9031RNX |
|---|---|---|---|---|---|---|
| Package | 48-VQFN (RGZ) 7x7 mm | 48-VQFN (RGZ) 7x7 mm - same | 48-VQFN (RGZ) 7x7 mm - same | 48-VQFN (RGZ) 7x7 mm - same | 48-LFCSP (QFN) 7x7 mm - compatible footprint | 48-QFN 7x7 mm - compatible footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Microchip Technology |
| Data Rate | 10/100/1000 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps | 10/100/1000 Mbps |
| MAC Interface | RGMII / SGMII | RGMII / SGMII | RGMII / SGMII | RGMII / SGMII | RGMII / SGMII | RGMII only |
| Operating Temperature | -40 C to +85 C (industrial) | 0 C to +70 C (commercial) | -40 C to +85 C (industrial) | -40 C to +85 C (extended) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) |
| IEEE 1588 Timestamping | Yes (hardware) | Yes | Yes | Yes | Yes | Yes |
| Cable Diagnostics (TDR) | Built-in | Built-in | Built-in | Built-in | Built-in | Built-in |
Diferensiator Kunci
- Best-in-class 8 kV IEC 61000-4-2 ESD on MDI pins (vsADIN1300BCPZ-R7)
- RGMII + SGMII dual MAC interface in same package (vsKSZ9031RNX)
- Industrial -40C to +85C operating range across entire family (vsDP83867CSRGZ)
Catatan Desain
Place the 25 MHz crystal within 50 mm of the XI/XO pins and guard the traces with a continuous ground plane to avoid spurious frequency deviation. Route the four MDI differential pairs (MDI_A+/-, B+/-, C+/-, D+/-) with 100 ohm differential impedance, length-matched within 2 mm, and reference them to an unbroken ground pour. Add a 1 nF HV decoupling cap on each MDI center-tap to provide AC return paths and reduce common-mode emissions, following TI reference design SNLA088.
Estimated: at gigabit full-duplex traffic the DP83867IRRGZ dissipates approximately 1.4 W (typical supply currents 2.5 V at 540 mA and 1.1 V at 90 mA). The 48-VQFN (RGZ) thermal pad must be soldered to a ground copper pour of at least 25 mm x 25 mm on the top and inner layers to keep theta_JA below 30 C/W. Without the EP properly soldered, junction temperature can exceed 100 C in sealed industrial enclosures and trigger thermal shutdown.
Do not leave the RBIAS pin floating - it requires a 11 kohm 1% resistor to ground to set internal bias currents, otherwise the PHY fails to link. Strap pins (RX_DV, RX_ER, CRS, COL, AN_EN, AN_1, EEE_DIS) define MAC interface and auto-negotiation defaults at reset; if left floating they default to internal pull-ups that may not match the host MAC mode. Always check the strap-pin state table in Section 8 of the TI datasheet before PCB layout.
Keep the MDC/MDIO traces short (<100 mm) and pull MDIO up to VDDIO with a 1.5 kohm to 10 kohm resistor for reliable management transactions. For SGMII, route the differential SGMII_SD_P/N pair with 100 ohm differential impedance and length-match to within 0.5 mm of the host serdes pins; mismatched SGMII length will cause eye closure and CRC errors at gigabit.
Informasi Konformitas
RoHS compliant per TI product page. Industrial temperature grade (-40C to +85C), not automotive AEC-Q100 qualified - use DP83867IRRGZ-Q1 for automotive. IEC 61000-4-2 8 kV ESD on MDI pins per TI datasheet.
