DRV8814PWPR - 47V 2.5A Dual Brushed DC Motor Driver | TI
MPN: DRV8814PWPR ✓ AktifDRV8814PWPR Ringkasan
A dual H-bridge motor driver is a power IC that integrates four power MOSFET switches and their control logic into one package so a microcontroller can command direction, brake, coast, and PWM-based current regulation on two DC motors (or one bipolar stepper) from a single supply rail. These devices sit in the broader hierarchy of motor control IC -> motion control -> power management, and the DRV8814 family is part of TI's brushed-DC driver portfolio distinguished by integrated current-sense and parallel interface control.
Key features of the DRV8814PWPR include four-level winding current control, multiple decay modes (slow decay, fast decay, and mixed decay), a PHASE/EN parallel interface for direction and enable, an internal inrush current limiter that protects the supply rail at startup, and built-in protection features including overcurrent protection (OCP), thermal shutdown (TSD), undervoltage lockout (UVLO), and fault-current reporting via the FLT pin. The HTSSOP-28 PowerPAD package delivers a low thermal resistance of approximately 31 °C/W (junction-to-case), enabling continuous 2.5 A operation with moderate PCB copper area. The parallel control scheme allows four discrete control inputs, simplifying host-firmware logic and reducing MCU timer overhead compared to PWM-only stepper interfaces.
The DRV8814PWPR is typically used in printers, scanners, robotic actuators, automated teller machines, textile machinery, and office automation. Its 45-V absolute-maximum supply tolerance also makes it compatible with 24-V and 36-V industrial bus rails. The DRV8841 and DRV8843 are related TI parts but use different interfaces and are not drop-in compatible.
This page synthesizes distributor pricing, drop-in same-package alternatives, parametric tables, and practical design notes not consolidated on the manufacturer product page.
Alternatif penggantian untuk DRV8814PWPR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DRV8814PWPR (sama faktor bentuk dan footprint) — berbeda di dalam Package, RoHS Status, Control Interface, Number of Channels, Operating Temperature.
DRV8814PWP
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DRV8814PWPR-Q1
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
DRV8801PWP
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DRV8806PWPR
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →DRV8841PWPR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DRV8814PWPR Rating Maksimal & Karakteristik Listrik
| Motor Type | Brushed DC (dual H-bridge) |
| Tegangan Pemuat Kerja | 8 V to 45 V |
| Absolute Maximum Supply Voltage | 47 V |
| Maximum Drive Current | 2.5 A per channel (at 24 V, TA = 25 °C) |
| Number of H-Bridges | 2 |
| Control Interface | Parallel (PHASE/EN) |
| Current Control | 4-level winding current control |
| Decay Modes | Slow, fast, mixed |
| Inrush Protection | Yes (integrated) |
| Protection Features | OCP, TSD, UVLO, FLT pin reporting |
| Rentang Suhu Kerja | -40 °C to +85 °C |
| Paket | 28-HTSSOP (PWP) with PowerPAD, exposed thermal pad |
| Tipe Mounting | Surface Mount |
| Status RoHS | Compliant (RoHS & no Sb/Br) |
| Thermal Resistance (θJC) | approximately 31 °C/W (PowerPAD) |
Konfigurasi Pin DRV8814PWPR
| Pin produk 1 | OUT1B — H-bridge 1 output B |
| Pin produk 2 | OUT1A — H-bridge 1 output A |
| Pin produk 3 | GND — Ground |
| Pin produk 4 | OUT2B — H-bridge 2 output B |
| Pin produk 5 | OUT2A — H-bridge 2 output A |
| Pin produk 6 | NC — Not connected (per datasheet) |
| Pin produk 7 | GND — Ground |
| Pin produk 8 | VCP — Charge pump reservoir capacitor |
| Pin produk 9 | VM — Motor supply voltage |
| Pin produk 10 | VM — Motor supply voltage |
| Pin produk 11 | GND — Ground |
| Pin produk 12 | DECAY — Decay mode select |
| Pin produk 13 | FLT — Fault output (open-drain, active low) |
| Pin produk 14 | VREF — Current threshold reference |
| Pin produk 15 | NC — Not connected (per datasheet) |
| Pin produk 16 | EN1 — H-bridge 1 enable input |
| Pin produk 17 | PHASE1 — H-bridge 1 phase (direction) input |
| Pin produk 18 | EN2 — H-bridge 2 enable input |
| Pin produk 19 | PHASE2 — H-bridge 2 phase (direction) input |
| Pin produk 20 | NC — Not connected (per datasheet) |
| Pin produk 21 | GND — Ground |
| Pin produk 22 | NC — Not connected (per datasheet) |
| Pin produk 23 | NC — Not connected (per datasheet) |
| Pin produk 24 | NC — Not connected (per datasheet) |
| Pin produk 25 | NC — Not connected (per datasheet) |
| Pin produk 26 | NC — Not connected (per datasheet) |
| Pin produk 27 | NC — Not connected (per datasheet) |
| Pin produk 28 | NC — Not connected (per datasheet) |
Aplikasi Umum
DRV8814PWPR cocok untuk 6 aplikasis: Office Printer Paper Feed & Carriage Motors, Document Scanner Belt Drive, Automated Teller Machine (ATM) Card & Cash Transport, Industrial Robotic Actuator, Textile & Sewing Machine Drive, Vending Machine Dispense Motors.
Office Printer Paper Feed & Carriage Motors
The DRV8814PWPR is purpose-built for office printers where two brushed DC motors drive paper feed rollers and the print-head carriage. Its 8-45 V supply range covers the printer's main logic rail plus motor back-EMF headroom, while 2.5 A per channel powers high-inertia paper-feed rollers. Four-level winding current control and slow/fast/mixed decay settings let designers minimize audible whine and EMI. Inrush protection prevents the high startup current of carriage motors from collapsing the main rail. Parallel PHASE/EN control simplifies the printer's MCU firmware compared to stepper pulse-trains.
Direkomendasikan
Document Scanner Belt Drive
Flatbed and sheet-fed scanners use two brushed DC motors: one for the document feed belt and one for the imaging bar carriage. The DRV8814PWPR's dual H-bridge topology drives both motors from a single 24-V rail, halving component count versus discrete drivers. The integrated fault (FLT) output signals the scanner controller on overcurrent or overtemperature events, enabling graceful shutdown to protect sensitive CCD/CIS sensors. 2.5 A continuous current handles the stall current of small geared scanner motors at start.
Direkomendasikan
Automated Teller Machine (ATM) Card & Cash Transport
ATMs depend on brushed DC gear motors for card readers, bill acceptors, and shutter control. The DRV8814PWPR's 45-V operating tolerance and 2.5 A drive allow one IC to handle multiple ATM motor channels, reducing BOM count. Integrated inrush protection prevents card-reader motor startup transients from triggering upstream supply brown-outs, while OCP and TSD protect against jammed-card stalls. The wide -40 °C to +85 °C operating range supports ATM outdoor and unheated vestibule installations.
Direkomendasikan
Industrial Robotic Actuator
Small industrial robotic arms and pick-and-place actuators use brushed DC gear motors for joint motion. The DRV8814PWPR delivers 2.5 A per channel for typical 12-24 V DC gear motors, with 47-V transient tolerance for back-EMF during deceleration. Four-level current control enables torque limiting via VREF, providing software-defined joint current caps for collaborative safety. The HTSSOP-28 PowerPAD package supports reflow soldering on standard 4-layer industrial PCBs with moderate copper area.
Direkomendasikan
Textile & Sewing Machine Drive
Industrial sewing and embroidery machines use brushed DC motors for fabric feed and needle-bar positioning. The DRV8814PWPR's parallel PHASE/EN interface allows the machine controller to drive two axes from a single IC, with mixed-decay mode minimizing needle-bar overshoot at high PWM rates. 2.5 A continuous current handles the inrush of sewing-motor start, while integrated inrush protection prevents mains-side supply collapse in low-cost sewing machine power stages.
Direkomendasikan
Vending Machine Dispense Motors
Vending machines use brushed DC gear motors for spiral coil dispensing of snacks, drinks, and tickets. The DRV8814PWPR's 2.5 A per channel drives typical 12-24 V vending dispenser motors, with OCP and TSD protecting against jammed spiral jams. The 8-45 V supply range accommodates 24-V vending bus rails with inductive transient headroom. Parallel control reduces MCU overhead, freeing the controller to manage payment, inventory, and telemetry tasks in real time.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DRV8814PWPR — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DRV8814PWP | DRV8814PWPR-Q1 | DRV8801PWP | DRV8806PWPR | DRV8841PWPR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-HTSSOP (PWP) with PowerPAD | 28-HTSSOP (PWP) - same | 28-HTSSOP (PWP) - same | 28-HTSSOP (PWP) - same | 28-HTSSOP (PWP) - same | 28-HTSSOP (PWP) - same |
| Operating Voltage | 8 V to 45 V (47 V abs max) | 8 V to 45 V | 8 V to 45 V | 8 V to 38 V | 8 V to 38 V | 8 V to 45 V |
| Maximum Drive Current | 2.5 A per channel | 2.5 A | 2.5 A | 2.5 A (single H-bridge) | 0.5 A | 2.5 A |
| Number of H-Bridges | 2 | 2 | 2 | 1 | 2 | 2 |
| Control Interface | Parallel (PHASE/EN) | Parallel (PHASE/EN) | Parallel (PHASE/EN) | Parallel (PHASE/EN) | Parallel (PHASE/EN) | Different interface - verify |
| Inrush Protection | Yes (integrated) | Yes | Yes | No | No | No |
| Automotive Grade (AEC-Q100) | No (standard grade) | No | Yes | No | No | No |
Diferensiator Kunci
- Integrated inrush current protection (vsDRV8801PWP)
- 47-V absolute maximum supply tolerance (vsDRV8806PWPR)
- 2.5 A continuous per channel (vsDRV8806PWPR)
Catatan Desain
Estimated: at VM = 24 V and 2.5 A continuous per channel with both bridges active, total H-bridge loss is approximately 8-12 W depending on RDS(on) and PWM duty. The HTSSOP-28 PowerPAD has θJC of approximately 31 °C/W, requiring thermal vias under the PowerPAD and at least 1 square inch of 2-oz copper on top and bottom layers to keep Tj below 125 °C. For both bridges at 2.5 A simultaneously, derate current or use forced-air; single bridge at 2.5 A continuous is typically achievable with the standard PowerPAD footprint.
Place the VM supply bypass (10 µF ceramic + 100 µF electrolytic) as close to pins 9-10 (VM) as possible to absorb motor back-EMF. The VCP capacitor (0.1 µF, 16 V) between pin 8 (VCP) and pin 11 (GND) must be within 5 mm of the IC. The exposed PowerPAD must be soldered to a ground copper plane with a 3x3 thermal via grid (0.3 mm vias) for proper heatsinking. Keep motor output traces away from control logic traces to minimize dV/dt coupling.
Do not exceed 45 V continuous on VM; inductive transients from motor commutation can momentarily exceed this. Always provide a reverse-biased flyback path (or rely on the integrated clamping) and add a TVS or bulk cap if motor inductance is high. The FLT pin is open-drain and requires a pull-up; if not used, tie it to GND or leave NC per datasheet. Do not float any enable input (EN1/EN2, PHASE1/PHASE2); floating inputs can cause unexpected motor activation. The DECAY pin selects decay mode (slow/fast/mixed) and must be tied high, low, or driven by MCU - never left floating.
Informasi Konformitas
RoHS compliant and Sb/Br-free per TI product page. Standard grade - select DRV8814PWPR-Q1 variant for AEC-Q100 automotive qualification.
